1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
|
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the Olimex STM32-P103 proto board.
*/
/*
* Board identifier.
*/
#define BOARD_OLIMEX_STM32_P103
#define BOARD_NAME "Olimex STM32-P103"
/*
* Board frequencies.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 8000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F103xB
/*
* IO pins assignments.
*/
#define GPIOA_BUTTON 0
#define GPIOA_SPI1NSS 4
#define GPIOB_SPI2NSS 12
#define GPIOC_USB_P 4
#define GPIOC_MMCWP 6
#define GPIOC_MMCCP 7
#define GPIOC_CAN_CNTL 10
#define GPIOC_USB_DISC 11
#define GPIOC_LED 12
/*
* IO lines assignments.
*/
#define LINE_BUTTON PAL_LINE(GPIOA, 0U)
#define LINE_SPI1NSS PAL_LINE(GPIOA, 4U)
#define LINE_SPI2NSS PAL_LINE(GPIOB, 12U)
#define LINE_USB_P PAL_LINE(GPIOC, 4U)
#define LINE_MMCWP PAL_LINE(GPIOC, 6U)
#define LINE_MMCCP PAL_LINE(GPIOC, 7U)
#define LINE_CAN_CNTL PAL_LINE(GPIOC, 10U)
#define LINE_USB_DISC PAL_LINE(GPIOC, 11U)
#define LINE_LED PAL_LINE(GPIOC, 12U)
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
* PA0 - Normal input (BUTTON).
* PA2 - Alternate output (USART2 TX).
* PA3 - Normal input (USART2 RX).
* PA11 - Normal input (USB DM).
* PA12 - Normal input (USB DP).
*/
#define VAL_GPIOACRL 0x88884B84 /* PA7...PA0 */
#define VAL_GPIOACRH 0x88844888 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup.
* Everything input with pull-up except:
* PB13 - Alternate output (MMC SPI2 SCK).
* PB14 - Normal input (MMC SPI2 MISO).
* PB15 - Alternate output (MMC SPI2 MOSI).
*/
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
#define VAL_GPIOBCRH 0xB4B88888 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input with pull-up except:
* PC4 - Normal input because there is an external resistor.
* PC6 - Normal input because there is an external resistor.
* PC7 - Normal input because there is an external resistor.
* PC10 - Push Pull output (CAN CNTRL).
* PC11 - Push Pull output (USB DISC).
* PC12 - Push Pull output (LED).
*/
#define VAL_GPIOCCRL 0x44848888 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x88833388 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
/*
* Port D setup.
* Everything input with pull-up except:
* PD0 - Normal input (XTAL).
* PD1 - Normal input (XTAL).
*/
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
#define VAL_GPIODODR 0xFFFFFFFF
/*
* Port E setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
/*
* USB bus activation macro, required by the USB driver.
*/
#define usb_lld_connect_bus(usbp) palClearPad(GPIOC, GPIOC_USB_DISC)
/*
* USB bus de-activation macro, required by the USB driver.
*/
#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOC, GPIOC_USB_DISC)
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
