aboutsummaryrefslogtreecommitdiffstats
path: root/os/hal/boards/OLIMEX_STM32_103STK/board.h
blob: 0d726c9b017256f69065017e5a6005684e376b52 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
/*
    ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

#ifndef _BOARD_H_
#define _BOARD_H_

/*
 * Setup for the Olimex STM32-103STK proto board.
 */

/*
 * Board identifier.
 */
#define BOARD_OLIMEX_STM32_103STK
#define BOARD_NAME              "Olimex STM32-103STK"

/*
 * Board frequencies.
 */
#define STM32_LSECLK            32768
#define STM32_HSECLK            8000000

/*
 * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
 */
#define STM32F103xB

/*
 * IO pins assignments.
 */
#define GPIOA_BUTTON_WAKEUP     0
#define GPIOC_BUTTON_TAMPER     13
#define GPIOC_JOY               5
#define GPIOC_JOY_CENTER_BUT    6

#define GPIOA_SPI1NSS           4
#define GPIOB_SPI2NSS           12

#define GPIOC_MMCWP             2
#define GPIOC_MMCCP             1

#define GPIOC_USB_P             4
#define GPIOC_LCD_RES           7
#define GPIOC_NRF_CE            8
#define GPIOC_NRF_IRQ           9
#define GPIOC_LCD_E             10

#define GPIOC_USB_DISC          11
#define GPIOC_LED               12

#define GPIOB_ACCEL_IRQ         5

/*
 * I/O ports initial setup, this configuration is established soon after reset
 * in the initialization code.
 *
 * The digits have the following meaning:
 *   0 - Analog input.
 *   1 - Push Pull output 10MHz.
 *   2 - Push Pull output 2MHz.
 *   3 - Push Pull output 50MHz.
 *   4 - Digital input.
 *   5 - Open Drain output 10MHz.
 *   6 - Open Drain output 2MHz.
 *   7 - Open Drain output 50MHz.
 *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
 *   9 - Alternate Push Pull output 10MHz.
 *   A - Alternate Push Pull output 2MHz.
 *   B - Alternate Push Pull output 50MHz.
 *   C - Reserved.
 *   D - Alternate Open Drain output 10MHz.
 *   E - Alternate Open Drain output 2MHz.
 *   F - Alternate Open Drain output 50MHz.
 * Please refer to the STM32 Reference Manual for details.
 */

/*
 * Port A setup.
 * Everything input with pull-up except:
 * PA0  - Normal input      (BUTTON).
 * PA2  - Alternate output  (USART2 TX).
 * PA3  - Normal input      (USART2 RX).
 */
#define VAL_GPIOACRL            0x88884B84      /*  PA7...PA0 */
#define VAL_GPIOACRH            0x88888888      /* PA15...PA8 */
#define VAL_GPIOAODR            0xFFFFFFFF

/*
 * Port B setup.
 * Everything input with pull-up except:
 * PB6,7   - Alternate open drain (I2C1).
 * PB10,11 - Alternate open drain (I2C2).
 * PB12    - Push Pull output  (MMC SPI2 NSS).
 * PB13    - Alternate output  (MMC SPI2 SCK).
 * PB14    - Normal input      (MMC SPI2 MISO).
 * PB15    - Alternate output  (MMC SPI2 MOSI).
 */
#define VAL_GPIOBCRL            0xEE888888      /*  PB7...PB0 */
#define VAL_GPIOBCRH            0xB4B3EE88      /* PB15...PB8 */
#define VAL_GPIOBODR            0xFFFFFFFF

/*
 * Port C setup.
 * Everything input with pull-up except:
 * PC4  - Normal input because there is an external resistor.
 * PC5  - Analog input (joystick).
 * PC6  - Normal input because there is an external resistor.
 * PC7  - Normal input because there is an external resistor.
 * PC10 - Push Pull output (CAN CNTRL).
 * PC11 - Push Pull output (USB DISC).
 * PC12 - Open Drain output (LED).
 */
#define VAL_GPIOCCRL            0x44048888      /*  PC7...PC0 */
#define VAL_GPIOCCRH            0x88863388      /* PC15...PC8 */
#define VAL_GPIOCODR            0xFFFFFFFF

/*
 * Port D setup.
 * Everything input with pull-up except:
 * PD0  - Normal input (XTAL).
 * PD1  - Normal input (XTAL).
 */
#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
#define VAL_GPIODODR            0xFFFFFFFF

/*
 * Port E setup.
 * Everything input with pull-up except:
 */
#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
#define VAL_GPIOEODR            0xFFFFFFFF

/*
 * USB bus activation macro, required by the USB driver.
 */
#define usb_lld_connect_bus(usbp) palClearPad(GPIOC, GPIOC_USB_DISC)

/*
 * USB bus de-activation macro, required by the USB driver.
 */
#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOC, GPIOC_USB_DISC)

#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
  void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */

#endif /* _BOARD_H_ */