diff options
Diffstat (limited to 'os/hal/ports/STM32L1xx/hal_lld.c')
| -rw-r--r-- | os/hal/ports/STM32L1xx/hal_lld.c | 236 |
1 files changed, 236 insertions, 0 deletions
diff --git a/os/hal/ports/STM32L1xx/hal_lld.c b/os/hal/ports/STM32L1xx/hal_lld.c new file mode 100644 index 000000000..529099e6a --- /dev/null +++ b/os/hal/ports/STM32L1xx/hal_lld.c @@ -0,0 +1,236 @@ +/*
+ ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file STM32L1xx/hal_lld.c
+ * @brief STM32L1xx HAL subsystem low level driver source.
+ *
+ * @addtogroup HAL
+ * @{
+ */
+
+/* TODO: LSEBYP like in F3.*/
+
+#include "ch.h"
+#include "hal.h"
+
+/*===========================================================================*/
+/* Driver local definitions. */
+/*===========================================================================*/
+
+/*===========================================================================*/
+/* Driver exported variables. */
+/*===========================================================================*/
+
+/*===========================================================================*/
+/* Driver local variables and types. */
+/*===========================================================================*/
+
+/*===========================================================================*/
+/* Driver local functions. */
+/*===========================================================================*/
+
+/**
+ * @brief Initializes the backup domain.
+ */
+static void hal_lld_backup_domain_init(void) {
+
+ /* Backup domain access enabled and left open.*/
+ PWR->CR |= PWR_CR_DBP;
+
+ /* Reset BKP domain if different clock source selected.*/
+ if ((RCC->CSR & STM32_RTCSEL_MASK) != STM32_RTCSEL){
+ /* Backup domain reset.*/
+ RCC->CSR |= RCC_CSR_RTCRST;
+ RCC->CSR &= ~RCC_CSR_RTCRST;
+ }
+
+ /* If enabled then the LSE is started.*/
+#if STM32_LSE_ENABLED
+ RCC->CSR |= RCC_CSR_LSEON;
+ while ((RCC->CSR & RCC_CSR_LSERDY) == 0)
+ ; /* Waits until LSE is stable. */
+#endif
+
+#if STM32_RTCSEL != STM32_RTCSEL_NOCLOCK
+ /* If the backup domain hasn't been initialized yet then proceed with
+ initialization.*/
+ if ((RCC->CSR & RCC_CSR_RTCEN) == 0) {
+ /* Selects clock source.*/
+ RCC->CSR |= STM32_RTCSEL;
+
+ /* RTC clock enabled.*/
+ RCC->CSR |= RCC_CSR_RTCEN;
+ }
+#endif /* STM32_RTCSEL != STM32_RTCSEL_NOCLOCK */
+}
+
+/*===========================================================================*/
+/* Driver interrupt handlers. */
+/*===========================================================================*/
+
+/*===========================================================================*/
+/* Driver exported functions. */
+/*===========================================================================*/
+
+/**
+ * @brief Low level HAL driver initialization.
+ *
+ * @notapi
+ */
+void hal_lld_init(void) {
+
+ /* Reset of all peripherals.*/
+ rccResetAHB(~RCC_AHBRSTR_FLITFRST);
+ rccResetAPB1(~RCC_APB1RSTR_PWRRST);
+ rccResetAPB2(~0);
+
+ /* SysTick initialization using the system clock.*/
+ SysTick->LOAD = STM32_HCLK / CH_FREQUENCY - 1;
+ SysTick->VAL = 0;
+ SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
+ SysTick_CTRL_ENABLE_Msk |
+ SysTick_CTRL_TICKINT_Msk;
+
+ /* DWT cycle counter enable.*/
+ SCS_DEMCR |= SCS_DEMCR_TRCENA;
+ DWT_CTRL |= DWT_CTRL_CYCCNTENA;
+
+ /* PWR clock enabled.*/
+ rccEnablePWRInterface(FALSE);
+
+ /* Initializes the backup domain.*/
+ hal_lld_backup_domain_init();
+
+#if defined(STM32_DMA_REQUIRED)
+ dmaInit();
+#endif
+
+ /* Programmable voltage detector enable.*/
+#if STM32_PVD_ENABLE
+ PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
+#endif /* STM32_PVD_ENABLE */
+}
+
+/**
+ * @brief STM32L1xx voltage, clocks and PLL initialization.
+ * @note All the involved constants come from the file @p board.h.
+ * @note This function should be invoked just after the system reset.
+ *
+ * @special
+ */
+#if defined(STM32L1XX_MD) || defined(__DOXYGEN__)
+/**
+ * @brief Clocks and internal voltage initialization.
+ */
+void stm32_clock_init(void) {
+
+#if !STM32_NO_INIT
+ /* PWR clock enable.*/
+ RCC->APB1ENR = RCC_APB1ENR_PWREN;
+
+ /* Core voltage setup.*/
+ while ((PWR->CSR & PWR_CSR_VOSF) != 0)
+ ; /* Waits until regulator is stable. */
+ PWR->CR = STM32_VOS;
+ while ((PWR->CSR & PWR_CSR_VOSF) != 0)
+ ; /* Waits until regulator is stable. */
+
+ /* Initial clocks setup and wait for MSI stabilization, the MSI clock is
+ always enabled because it is the fallback clock when PLL the fails.
+ Trim fields are not altered from reset values.*/
+ RCC->CFGR = 0;
+ RCC->ICSCR = (RCC->ICSCR & ~STM32_MSIRANGE_MASK) | STM32_MSIRANGE;
+ RCC->CSR = RCC_CSR_RMVF;
+ RCC->CR = RCC_CR_MSION;
+ while ((RCC->CR & RCC_CR_MSIRDY) == 0)
+ ; /* Waits until MSI is stable. */
+
+#if STM32_HSI_ENABLED
+ /* HSI activation.*/
+ RCC->CR |= RCC_CR_HSION;
+ while ((RCC->CR & RCC_CR_HSIRDY) == 0)
+ ; /* Waits until HSI is stable. */
+#endif
+
+#if STM32_HSE_ENABLED
+#if defined(STM32_HSE_BYPASS)
+ /* HSE Bypass.*/
+ RCC->CR |= RCC_CR_HSEBYP;
+#endif
+ /* HSE activation.*/
+ RCC->CR |= RCC_CR_HSEON;
+ while ((RCC->CR & RCC_CR_HSERDY) == 0)
+ ; /* Waits until HSE is stable. */
+#endif
+
+#if STM32_LSI_ENABLED
+ /* LSI activation.*/
+ RCC->CSR |= RCC_CSR_LSION;
+ while ((RCC->CSR & RCC_CSR_LSIRDY) == 0)
+ ; /* Waits until LSI is stable. */
+#endif
+
+#if STM32_LSE_ENABLED
+ /* LSE activation, have to unlock the register.*/
+ if ((RCC->CSR & RCC_CSR_LSEON) == 0) {
+ PWR->CR |= PWR_CR_DBP;
+ RCC->CSR |= RCC_CSR_LSEON;
+ PWR->CR &= ~PWR_CR_DBP;
+ }
+ while ((RCC->CSR & RCC_CSR_LSERDY) == 0)
+ ; /* Waits until LSE is stable. */
+#endif
+
+#if STM32_ACTIVATE_PLL
+ /* PLL activation.*/
+ RCC->CFGR |= STM32_PLLDIV | STM32_PLLMUL | STM32_PLLSRC;
+ RCC->CR |= RCC_CR_PLLON;
+ while (!(RCC->CR & RCC_CR_PLLRDY))
+ ; /* Waits until PLL is stable. */
+#endif
+
+ /* Other clock-related settings (dividers, MCO etc).*/
+ RCC->CR |= STM32_RTCPRE;
+ RCC->CFGR |= STM32_MCOPRE | STM32_MCOSEL |
+ STM32_PPRE2 | STM32_PPRE1 | STM32_HPRE;
+ RCC->CSR |= STM32_RTCSEL;
+
+ /* Flash setup and final clock selection.*/
+#if defined(STM32_FLASHBITS1)
+ FLASH->ACR = STM32_FLASHBITS1;
+#endif
+#if defined(STM32_FLASHBITS2)
+ FLASH->ACR = STM32_FLASHBITS2;
+#endif
+
+ /* Switching to the configured clock source if it is different from MSI.*/
+#if (STM32_SW != STM32_SW_MSI)
+ RCC->CFGR |= STM32_SW; /* Switches on the selected clock source. */
+ while ((RCC->CFGR & RCC_CFGR_SWS) != (STM32_SW << 2))
+ ;
+#endif
+#endif /* STM32_NO_INIT */
+
+ /* SYSCFG clock enabled here because it is a multi-functional unit shared
+ among multiple drivers.*/
+ rccEnableAPB2(RCC_APB2ENR_SYSCFGEN, TRUE);
+}
+#else
+void stm32_clock_init(void) {}
+#endif
+
+/** @} */
|