diff options
Diffstat (limited to 'os/hal/platforms/STM8S/pal_lld.h')
| -rw-r--r-- | os/hal/platforms/STM8S/pal_lld.h | 229 |
1 files changed, 0 insertions, 229 deletions
diff --git a/os/hal/platforms/STM8S/pal_lld.h b/os/hal/platforms/STM8S/pal_lld.h deleted file mode 100644 index 86246a05b..000000000 --- a/os/hal/platforms/STM8S/pal_lld.h +++ /dev/null @@ -1,229 +0,0 @@ -/*
- ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-/**
- * @file STM8S/pal_lld.h
- * @brief STM8S GPIO low level driver header.
- *
- * @addtogroup PAL
- * @{
- */
-
-#ifndef _PAL_LLD_H_
-#define _PAL_LLD_H_
-
-#if HAL_USE_PAL || defined(__DOXYGEN__)
-
-/*===========================================================================*/
-/* Unsupported modes and specific modes */
-/*===========================================================================*/
-
-#undef PAL_MODE_INPUT_PULLDOWN
-
-/**
- * @brief STM8S specific alternate push-pull slow output mode.
- */
-#define PAL_MODE_OUTPUT_PUSHPULL_SLOW 16
-
-/**
- * @brief STM8S specific alternate open-drain slow output mode.
- */
-#define PAL_MODE_OUTPUT_OPENDRAIN_SLOW 17
-
-/*===========================================================================*/
-/* I/O Ports Types and constants. */
-/*===========================================================================*/
-
-/**
- * @brief Generic I/O ports static initializer.
- * @details An instance of this structure must be passed to @p palInit() at
- * system startup time in order to initialized the digital I/O
- * subsystem. This represents only the initial setup, specific pads
- * or whole ports can be reprogrammed at later time.
- */
-typedef struct {
-#if defined(STM8S105) || defined(__DOXYGEN__)
- GPIO_TypeDef P[7];
-#elif defined(STM8S207) || defined(STM8S208)
- GPIO_TypeDef P[9];
-#else
- GPIO_TypeDef P[6];
-#endif
-} PALConfig;
-
-/**
- * @brief Width, in bits, of an I/O port.
- */
-#define PAL_IOPORTS_WIDTH 8
-
-/**
- * @brief Whole port mask.
- * @brief This macro specifies all the valid bits into a port.
- */
-#define PAL_WHOLE_PORT ((ioportmask_t)0xFF)
-
-/**
- * @brief Digital I/O port sized unsigned type.
- */
-typedef uint8_t ioportmask_t;
-
-/**
- * @brief Digital I/O modes.
- */
-typedef uint8_t iomode_t;
-
-/**
- * @brief Port Identifier.
- */
-typedef GPIO_TypeDef *ioportid_t;
-
-/*===========================================================================*/
-/* I/O Ports Identifiers. */
-/*===========================================================================*/
-
-/**
- * @brief GPIO ports as a whole.
- */
-#define IOPORTS ((PALConfig *)0x5000)
-
-/**
- * @brief GPIO port A identifier.
- */
-#define IOPORT1 GPIOA
-
-/**
- * @brief GPIO port B identifier.
- */
-#define IOPORT2 GPIOB
-
-/**
- * @brief GPIO port C identifier.
- */
-#define IOPORT3 GPIOC
-
-/**
- * @brief GPIO port D identifier.
- */
-#define IOPORT4 GPIOD
-
-/**
- * @brief GPIO port E identifier.
- */
-#define IOPORT5 GPIOE
-
-/**
- * @brief GPIO port F identifier.
- */
-#define IOPORT6 GPIOF
-
-#if defined(STM8S207) || defined(STM8S208) || defined(STM8S105) || \
- defined(__DOXYGEN__)
-/**
- * @brief GPIO port G identifier.
- */
-#define IOPORT7 GPIOG
-#endif
-
-#if defined(STM8S207) || defined(STM8S208) || defined(__DOXYGEN__)
-/**
- * @brief GPIO port H identifier.
- */
-#define IOPORT8 GPIOH
-
-/**
- * @brief GPIO port I identifier.
- */
-#define IOPORT9 GPIOI
-#endif
-
-/*===========================================================================*/
-/* Implementation, some of the following macros could be implemented as */
-/* functions, if so please put them in pal_lld.c. */
-/*===========================================================================*/
-
-/**
- * @brief Low level PAL subsystem initialization.
- *
- * @param[in] config architecture-dependent ports configuration
- *
- * @notapi
- */
-#define pal_lld_init(config) (*IOPORTS = *(config))
-
-/**
- * @brief Reads the physical I/O port states.
- *
- * @param[in] port port identifier
- * @return The port bits.
- *
- * @notapi
- */
-#define pal_lld_readport(port) ((port)->IDR)
-
-/**
- * @brief Reads the output latch.
- * @details The purpose of this function is to read back the latched output
- * value.
- *
- * @param[in] port port identifier
- * @return The latched logical states.
- *
- * @notapi
- */
-#define pal_lld_readlatch(port) ((port)->ODR)
-
-/**
- * @brief Writes a bits mask on a I/O port.
- *
- * @param[in] port port identifier
- * @param[in] bits bits to be written on the specified port
- *
- * @notapi
- */
-#define pal_lld_writeport(port, bits) ((port)->ODR = (bits))
-
-/**
- * @brief Pads group mode setup.
- * @details This function programs a pads group belonging to the same port
- * with the specified mode.
- *
- * @param[in] port port identifier
- * @param[in] mask group mask
- * @param[in] offset group bit offset within the port
- * @param[in] mode group mode
- *
- * @notapi
- */
-#define pal_lld_setgroupmode(port, mask, offset, mode) \
- _pal_lld_setgroupmode(port, mask << offset, mode)
-
-extern ROMCONST PALConfig pal_default_config;
-
-#ifdef __cplusplus
-extern "C" {
-#endif
- void _pal_lld_setgroupmode(ioportid_t port,
- ioportmask_t mask,
- iomode_t mode);
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* HAL_USE_PAL */
-
-#endif /* _PAL_LLD_H_ */
-
-/** @} */
|