diff options
Diffstat (limited to 'os/hal/platforms/SPC5xx/LINFlex_v1/serial_lld.h')
| -rw-r--r-- | os/hal/platforms/SPC5xx/LINFlex_v1/serial_lld.h | 302 |
1 files changed, 0 insertions, 302 deletions
diff --git a/os/hal/platforms/SPC5xx/LINFlex_v1/serial_lld.h b/os/hal/platforms/SPC5xx/LINFlex_v1/serial_lld.h deleted file mode 100644 index cbd446b86..000000000 --- a/os/hal/platforms/SPC5xx/LINFlex_v1/serial_lld.h +++ /dev/null @@ -1,302 +0,0 @@ -/*
- SPC5 HAL - Copyright (C) 2013 STMicroelectronics
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-/**
- * @file SPC5xx/LINFlex_v1/serial_lld.h
- * @brief SPC5xx low level serial driver header.
- *
- * @addtogroup SERIAL
- * @{
- */
-
-#ifndef _SERIAL_LLD_H_
-#define _SERIAL_LLD_H_
-
-#if HAL_USE_SERIAL || defined(__DOXYGEN__)
-
-#include "spc5_linflex.h"
-
-/*===========================================================================*/
-/* Driver constants. */
-/*===========================================================================*/
-
-/**
- * @name Serial driver allowable modes
- * @{
- */
-#define SD_MODE_8BITS_PARITY_NONE (SPC5_UARTCR_WL)
-#define SD_MODE_8BITS_PARITY_EVEN (SPC5_UARTCR_WL | \
- SPC5_UARTCR_PCE)
-#define SD_MODE_8BITS_PARITY_ODD (SPC5_UARTCR_WL | \
- SPC5_UARTCR_PCE | \
- SPC5_UARTCR_OP)
-/** @} */
-
-/*===========================================================================*/
-/* Driver pre-compile time settings. */
-/*===========================================================================*/
-
-/**
- * @brief LINFlex-0 driver enable switch.
- * @details If set to @p TRUE the support for LINFlex-0 is included.
- */
-#if !defined(SPC5_SERIAL_USE_LINFLEX0) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_USE_LINFLEX0 FALSE
-#endif
-
-/**
- * @brief LINFlex-1 driver enable switch.
- * @details If set to @p TRUE the support for LINFlex-1 is included.
- */
-#if !defined(SPC5_SERIAL_USE_LINFLEX1) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_USE_LINFLEX1 FALSE
-#endif
-
-/**
- * @brief LINFlex-2 driver enable switch.
- * @details If set to @p TRUE the support for LINFlex-2 is included.
- */
-#if !defined(SPC5_SERIAL_USE_LINFLEX2) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_USE_LINFLEX2 FALSE
-#endif
-
-/**
- * @brief LINFlex-3 driver enable switch.
- * @details If set to @p TRUE the support for LINFlex-3 is included.
- */
-#if !defined(SPC5_SERIAL_USE_LINFLEX3) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_USE_LINFLEX3 FALSE
-#endif
-
-/**
- * @brief LINFlex-0 interrupt priority level setting.
- */
-#if !defined(SPC5_SERIAL_LINFLEX0_PRIORITY) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX0_PRIORITY 8
-#endif
-
-/**
- * @brief LINFlex-1 interrupt priority level setting.
- */
-#if !defined(SPC5_SERIAL_LINFLEX1_PRIORITY) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX1_PRIORITY 8
-#endif
-
-/**
- * @brief LINFlex-2 interrupt priority level setting.
- */
-#if !defined(SPC5_SERIAL_LINFLEX2_PRIORITY) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX2_PRIORITY 8
-#endif
-
-/**
- * @brief LINFlex-3 interrupt priority level setting.
- */
-#if !defined(SPC5_SERIAL_LINFLEX3_PRIORITY) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX3_PRIORITY 8
-#endif
-
-/**
- * @brief LINFlex-0 peripheral configuration when started.
- * @note The default configuration is 1 (always run) in run mode and
- * 2 (only halt) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX0_START_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX0_START_PCTL (SPC5_ME_PCTL_RUN(1) | \
- SPC5_ME_PCTL_LP(2))
-#endif
-
-/**
- * @brief LINFlex-0 peripheral configuration when stopped.
- * @note The default configuration is 0 (never run) in run mode and
- * 0 (never run) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX0_STOP_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX0_STOP_PCTL (SPC5_ME_PCTL_RUN(0) | \
- SPC5_ME_PCTL_LP(0))
-#endif
-
-/**
- * @brief LINFlex-1 peripheral configuration when started.
- * @note The default configuration is 1 (always run) in run mode and
- * 2 (only halt) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX1_START_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX1_START_PCTL (SPC5_ME_PCTL_RUN(1) | \
- SPC5_ME_PCTL_LP(2))
-#endif
-
-/**
- * @brief LINFlex-1 peripheral configuration when stopped.
- * @note The default configuration is 0 (never run) in run mode and
- * 0 (never run) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX1_STOP_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX1_STOP_PCTL (SPC5_ME_PCTL_RUN(0) | \
- SPC5_ME_PCTL_LP(0))
-#endif
-
-/**
- * @brief LINFlex-2 peripheral configuration when started.
- * @note The default configuration is 1 (always run) in run mode and
- * 2 (only halt) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX2_START_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX2_START_PCTL (SPC5_ME_PCTL_RUN(1) | \
- SPC5_ME_PCTL_LP(2))
-#endif
-
-/**
- * @brief LINFlex-2 peripheral configuration when stopped.
- * @note The default configuration is 0 (never run) in run mode and
- * 0 (never run) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX2_STOP_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX2_STOP_PCTL (SPC5_ME_PCTL_RUN(0) | \
- SPC5_ME_PCTL_LP(0))
-#endif
-
-/**
- * @brief LINFlex-3 peripheral configuration when started.
- * @note The default configuration is 1 (always run) in run mode and
- * 2 (only halt) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX3_START_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX3_START_PCTL (SPC5_ME_PCTL_RUN(1) | \
- SPC5_ME_PCTL_LP(2))
-#endif
-
-/**
- * @brief LINFlex-3 peripheral configuration when stopped.
- * @note The default configuration is 0 (never run) in run mode and
- * 0 (never run) in low power mode. The defaults of the run modes
- * are defined in @p hal_lld.h.
- */
-#if !defined(SPC5_SERIAL_LINFLEX3_STOP_PCTL) || defined(__DOXYGEN__)
-#define SPC5_SERIAL_LINFLEX3_STOP_PCTL (SPC5_ME_PCTL_RUN(0) | \
- SPC5_ME_PCTL_LP(0))
-#endif
-
-/*===========================================================================*/
-/* Derived constants and error checks. */
-/*===========================================================================*/
-
-#if SPC5_SERIAL_USE_LINFLEX0 && !SPC5_HAS_LINFLEX0
-#error "LINFlex-0 not present in the selected device"
-#endif
-
-#if SPC5_SERIAL_USE_LINFLEX1 && !SPC5_HAS_LINFLEX1
-#error "LINFlex-1 not present in the selected device"
-#endif
-
-#if SPC5_SERIAL_USE_LINFLEX2 && !SPC5_HAS_LINFLEX2
-#error "LINFlex-2 not present in the selected device"
-#endif
-
-#if SPC5_SERIAL_USE_LINFLEX3 && !SPC5_HAS_LINFLEX3
-#error "LINFlex-3 not present in the selected device"
-#endif
-
-#if !SPC5_SERIAL_USE_LINFLEX0 && !SPC5_SERIAL_USE_LINFLEX1 && \
- !SPC5_SERIAL_USE_LINFLEX2 && !SPC5_SERIAL_USE_LINFLEX3
-#error "SERIAL driver activated but no LINFlex peripheral assigned"
-#endif
-
-/*===========================================================================*/
-/* Driver data structures and types. */
-/*===========================================================================*/
-
-/**
- * @brief Generic Serial Driver configuration structure.
- * @details An instance of this structure must be passed to @p sdStart()
- * in order to configure and start a serial driver operations.
- * @note This structure content is architecture dependent, each driver
- * implementation defines its own version and the custom static
- * initializers.
- */
-typedef struct {
- /**
- * @brief Bit rate.
- */
- uint32_t speed;
- /**
- * @brief Mode flags.
- */
- uint8_t mode;
-} SerialConfig;
-
-/**
- * @brief @p SerialDriver specific data.
- */
-#define _serial_driver_data \
- _base_asynchronous_channel_data \
- /* Driver state.*/ \
- sdstate_t state; \
- /* Input queue.*/ \
- InputQueue iqueue; \
- /* Output queue.*/ \
- OutputQueue oqueue; \
- /* Input circular buffer.*/ \
- uint8_t ib[SERIAL_BUFFERS_SIZE]; \
- /* Output circular buffer.*/ \
- uint8_t ob[SERIAL_BUFFERS_SIZE]; \
- /* End of the mandatory fields.*/ \
- /* Pointer to the volatile LINFlex registers block.*/ \
- volatile struct spc5_linflex *linflexp;
-
-/*===========================================================================*/
-/* Driver macros. */
-/*===========================================================================*/
-
-/*===========================================================================*/
-/* External declarations. */
-/*===========================================================================*/
-
-#if SPC5_SERIAL_USE_LINFLEX0 && !defined(__DOXYGEN__)
-extern SerialDriver SD1;
-#endif
-#if SPC5_SERIAL_USE_LINFLEX1 && !defined(__DOXYGEN__)
-extern SerialDriver SD2;
-#endif
-#if SPC5_SERIAL_USE_LINFLEX2 && !defined(__DOXYGEN__)
-extern SerialDriver SD3;
-#endif
-#if SPC5_SERIAL_USE_LINFLEX3 && !defined(__DOXYGEN__)
-extern SerialDriver SD4;
-#endif
-
-#ifdef __cplusplus
-extern "C" {
-#endif
- void sd_lld_init(void);
- void sd_lld_start(SerialDriver *sdp, const SerialConfig *config);
- void sd_lld_stop(SerialDriver *sdp);
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* HAL_USE_SERIAL */
-
-#endif /* _SERIAL_LLD_H_ */
-
-/** @} */
|