1 files changed, 0 insertions, 93 deletions
diff --git a/os/hal/platforms/MSP430/platform.dox b/os/hal/platforms/MSP430/platform.dox
deleted file mode 100644
index 131743e66..000000000
--- a/os/hal/platforms/MSP430/platform.dox
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @defgroup MSP430_DRIVERS MSP430 Drivers
- * @details This section describes all the supported drivers on the MSP430
- *          platform and the implementation details of the single drivers.
- *
- * @ingroup platforms
- */
-
-/**
- * @defgroup MSP430_HAL MSP430 Initialization Support
- * @details The MSP430 HAL support is responsible for system initialization.
- *
- * @section msp430_hal_1 Supported HW resources
- * - DCOCTL.
- * - BCSCTL1.
- * - BCSCTL2.
- * .
- * @section msp430_hal_2 MSP430 HAL driver implementation features
- * - Clock source selection.
- * .
- * @ingroup MSP430_DRIVERS
- */
-
-/**
- * @defgroup MSP430_PAL MSP430 PAL Support
- * @details The MSP430 PAL driver uses the PORT peripherals.
- *
- * @section msp430_pal_1 Supported HW resources
- * - PORT1 (where present).
- * - PORT2 (where present).
- * - PORT3 (where present).
- * - PORT4 (where present).
- * - PORT5 (where present).
- * - PORT6 (where present).
- * .
- * @section msp430_pal_2 MSP430 PAL driver implementation features
- * The PAL driver implementation fully supports the following hardware
- * capabilities:
- * - 8 bits wide ports.
- * - Atomic set/reset/toggle functions because special MSP430 instruction set.
- * - Output latched regardless of the pad setting.
- * - Direct read of input pads regardless of the pad setting.
- * .
- * @section msp430_pal_3 Supported PAL setup modes
- * The MSP430 PAL driver supports the following I/O modes:
- * - @p PAL_MODE_RESET.
- * - @p PAL_MODE_UNCONNECTED.
- * - @p PAL_MODE_INPUT.
- * - @p PAL_MODE_OUTPUT_PUSHPULL.
- * .
- * Any attempt to setup an invalid mode is ignored.
- *
- * @section msp430_pal_4 Suboptimal behavior
- * The MSP430 PORT is less than optimal in several areas, the limitations
- * should be taken in account while using the PAL driver:
- * - Bus/group writes is not atomic.
- * - Pad/group mode setup is not atomic.
- * .
- * @ingroup MSP430_DRIVERS
- */
-
-/**
- * @defgroup MSP430_SERIAL MSP430 Serial Support
- * @details The MSP430 Serial driver uses the USART peripherals in a
- *          buffered, interrupt driven, implementation.
- *
- * @section msp430_serial_1 Supported HW resources
- * The serial driver can support any of the following hardware resources:
- * - USART0.
- * - USART1.
- * .
- * @section msp430_serial_2 MSP430 Serial driver implementation features
- * - Each USART can be independently enabled and programmed.
- * - Fully interrupt driven.
- * .
- * @ingroup MSP430_DRIVERS
- */