1 files changed, 0 insertions, 104 deletions
diff --git a/os/hal/platforms/LPC8xx/platform.dox b/os/hal/platforms/LPC8xx/platform.dox
deleted file mode 100644
index 85b60bcad..000000000
--- a/os/hal/platforms/LPC8xx/platform.dox
+++ /dev/null
@@ -1,104 +0,0 @@
-/*
-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @defgroup LPC8xx LPC8xx Drivers
- * @details This section describes all the supported drivers on the LPC8xx
- *          platform and the implementation details of the single drivers.
- *
- * @ingroup platforms
- */
-
-/**
- * @defgroup LPC8xx_HAL LPC8xx Initialization Support
- * @details The LPC8xx HAL support is responsible for system initialization.
- *
- * @section lpc8xx_hal_1 Supported HW resources
- * - SYSCON.
- * - Flash.
- * .
- * @section lpc8xx_hal_2 LPC8xx HAL driver implementation features
- * - Clock tree initialization.
- * - Clock source selection.
- * - Flash controller initialization.
- * - SYSTICK initialization based on current clock and kernel required rate.
- * .
- * @ingroup LPC8xx
- */
-
-/**
- * @defgroup LPC8xx_GPT LPC8xx GPT Support
- * @details The LPC8xx GPT driver uses the MRT peripheral.
- *
- * @section lpc8xx_gpt_1 Supported HW resources
- * - MRT.
- * .
- * @section lpc8xx_gpt_2 LPC8xx GPT driver implementation features
- * - Each timer can be independently enabled and programmed.
- * - Programmable MRT interrupt priority level.
- * .
- * @ingroup LPC8xx
- */
-
-/**
- * @defgroup LPC8xx_PAL LPC8xx PAL Support
- * @details The LPC8xx PAL driver uses the GPIO peripheral.
- *
- * @section lpc8xx_pal_1 Supported HW resources
- * - GPIO_PORT.
- * .
- * @section lpc8xx_pal_2 LPC8xx PAL driver implementation features
- * - 18 bits wide ports.
- * - Atomic set/reset functions.
- * - Atomic Toggle functions.
- * - Atomic set+reset function (atomic bus operations).
- * - Output latched regardless of the pad setting.
- * - Direct read of input pads regardless of the pad setting.
- * .
- * @section lpc8xx_pal_3 Supported PAL setup modes
- * - @p PAL_MODE_RESET.
- * - @p PAL_MODE_UNCONNECTED.
- * - @p PAL_MODE_INPUT.
- * - @p PAL_MODE_OUTPUT_PUSHPULL.
- * .
- * Any attempt to setup an invalid mode is ignored.
- *
- * @section lpc8xx_pal_4 Suboptimal behavior
- * Some GPIO features are less than optimal:
- * - Group operations are not atomic.
- * - Pull-up and Pull-down resistors cannot be programmed through the PAL
- *   driver and must be programmed separately using the IOCON peripheral.
- * .
- * @ingroup LPC8xx
- */
-
-/**
- * @defgroup LPC8xx_SERIAL LPC8xx Serial Support
- * @details The LPC8xx Serial driver uses the UART peripheral in a
- *          buffered, interrupt driven, implementation.
- *
- * @section lpc8xx_serial_1 Supported HW resources
- * The serial driver can support any of the following hardware resources:
- * - UART.
- * .
- * @section lpc8xx_serial_2 LPC8xx Serial driver implementation features
- * - Clock stop for reduced power usage when the driver is in stop state.
- * - Fully interrupt driven.
- * - Programmable priority level.
- * .
- * @ingroup LPC8xx
- */
-