diff options
Diffstat (limited to 'demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg')
4 files changed, 1732 insertions, 0 deletions
diff --git a/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/chconf.h b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/chconf.h new file mode 100644 index 000000000..dcd31d1eb --- /dev/null +++ b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/chconf.h @@ -0,0 +1,714 @@ +/*
+ ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/chconf.h
+ * @brief Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ * contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef CHCONF_H
+#define CHCONF_H
+
+#define _CHIBIOS_RT_CONF_
+#define _CHIBIOS_RT_CONF_VER_6_0_
+
+/*===========================================================================*/
+/**
+ * @name System timers settings
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief System time counter resolution.
+ * @note Allowed values are 16 or 32 bits.
+ */
+#if !defined(CH_CFG_ST_RESOLUTION)
+#define CH_CFG_ST_RESOLUTION 16
+#endif
+
+/**
+ * @brief System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ * setting also defines the system tick time unit.
+ */
+#if !defined(CH_CFG_ST_FREQUENCY)
+#define CH_CFG_ST_FREQUENCY 2000
+#endif
+
+/**
+ * @brief Time intervals data size.
+ * @note Allowed values are 16, 32 or 64 bits.
+ */
+#if !defined(CH_CFG_INTERVALS_SIZE)
+#define CH_CFG_INTERVALS_SIZE 32
+#endif
+
+/**
+ * @brief Time types data size.
+ * @note Allowed values are 16 or 32 bits.
+ */
+#if !defined(CH_CFG_TIME_TYPES_SIZE)
+#define CH_CFG_TIME_TYPES_SIZE 32
+#endif
+
+/**
+ * @brief Time delta constant for the tick-less mode.
+ * @note If this value is zero then the system uses the classic
+ * periodic tick. This value represents the minimum number
+ * of ticks that is safe to specify in a timeout directive.
+ * The value one is not valid, timeouts are rounded up to
+ * this value.
+ */
+#if !defined(CH_CFG_ST_TIMEDELTA)
+#define CH_CFG_ST_TIMEDELTA 2
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ * threads before preemption occurs. Setting this value to zero
+ * disables the preemption for threads with equal priority and the
+ * round robin becomes cooperative. Note that higher priority
+ * threads can still preempt, the kernel is always preemptive.
+ * @note Disabling the round robin preemption makes the kernel more compact
+ * and generally faster.
+ * @note The round robin preemption is not supported in tickless mode and
+ * must be set to zero in that case.
+ */
+#if !defined(CH_CFG_TIME_QUANTUM)
+#define CH_CFG_TIME_QUANTUM 0
+#endif
+
+/**
+ * @brief Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ * then the whole available RAM is used. The core memory is made
+ * available to the heap allocator and/or can be used directly through
+ * the simplified core memory allocator.
+ *
+ * @note In order to let the OS manage the whole RAM the linker script must
+ * provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note Requires @p CH_CFG_USE_MEMCORE.
+ */
+#if !defined(CH_CFG_MEMCORE_SIZE)
+#define CH_CFG_MEMCORE_SIZE 0
+#endif
+
+/**
+ * @brief Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ * does not spawn the idle thread. The application @p main()
+ * function becomes the idle thread and must implement an
+ * infinite loop.
+ */
+#if !defined(CH_CFG_NO_IDLE_THREAD)
+#define CH_CFG_NO_IDLE_THREAD FALSE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ * is used when two possible implementations exist.
+ *
+ * @note This is not related to the compiler optimization options.
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_OPTIMIZE_SPEED)
+#define CH_CFG_OPTIMIZE_SPEED TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Time Measurement APIs.
+ * @details If enabled then the time measurement APIs are included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_TM)
+#define CH_CFG_USE_TM TRUE
+#endif
+
+/**
+ * @brief Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_REGISTRY)
+#define CH_CFG_USE_REGISTRY TRUE
+#endif
+
+/**
+ * @brief Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_WAITEXIT)
+#define CH_CFG_USE_WAITEXIT TRUE
+#endif
+
+/**
+ * @brief Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_SEMAPHORES)
+#define CH_CFG_USE_SEMAPHORES TRUE
+#endif
+
+/**
+ * @brief Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ * priority rather than in FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#if !defined(CH_CFG_USE_SEMAPHORES_PRIORITY)
+#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE
+#endif
+
+/**
+ * @brief Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_MUTEXES)
+#define CH_CFG_USE_MUTEXES TRUE
+#endif
+
+/**
+ * @brief Enables recursive behavior on mutexes.
+ * @note Recursive mutexes are heavier and have an increased
+ * memory footprint.
+ *
+ * @note The default is @p FALSE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#if !defined(CH_CFG_USE_MUTEXES_RECURSIVE)
+#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE
+#endif
+
+/**
+ * @brief Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#if !defined(CH_CFG_USE_CONDVARS)
+#define CH_CFG_USE_CONDVARS TRUE
+#endif
+
+/**
+ * @brief Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ * specification are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_CONDVARS.
+ */
+#if !defined(CH_CFG_USE_CONDVARS_TIMEOUT)
+#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE
+#endif
+
+/**
+ * @brief Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_EVENTS)
+#define CH_CFG_USE_EVENTS TRUE
+#endif
+
+/**
+ * @brief Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ * are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_EVENTS.
+ */
+#if !defined(CH_CFG_USE_EVENTS_TIMEOUT)
+#define CH_CFG_USE_EVENTS_TIMEOUT TRUE
+#endif
+
+/**
+ * @brief Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_MESSAGES)
+#define CH_CFG_USE_MESSAGES TRUE
+#endif
+
+/**
+ * @brief Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ * FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_MESSAGES.
+ */
+#if !defined(CH_CFG_USE_MESSAGES_PRIORITY)
+#define CH_CFG_USE_MESSAGES_PRIORITY FALSE
+#endif
+
+/**
+ * @brief Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ * included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#if !defined(CH_CFG_USE_MAILBOXES)
+#define CH_CFG_USE_MAILBOXES TRUE
+#endif
+
+/**
+ * @brief Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_MEMCORE)
+#define CH_CFG_USE_MEMCORE TRUE
+#endif
+
+/**
+ * @brief Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
+ * @p CH_CFG_USE_SEMAPHORES.
+ * @note Mutexes are recommended.
+ */
+#if !defined(CH_CFG_USE_HEAP)
+#define CH_CFG_USE_HEAP TRUE
+#endif
+
+/**
+ * @brief Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_MEMPOOLS)
+#define CH_CFG_USE_MEMPOOLS TRUE
+#endif
+
+/**
+ * @brief Objects FIFOs APIs.
+ * @details If enabled then the objects FIFOs APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_OBJ_FIFOS)
+#define CH_CFG_USE_OBJ_FIFOS TRUE
+#endif
+
+/**
+ * @brief Pipes APIs.
+ * @details If enabled then the pipes APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_CFG_USE_PIPES)
+#define CH_CFG_USE_PIPES TRUE
+#endif
+
+/**
+ * @brief Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_WAITEXIT.
+ * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
+ */
+#if !defined(CH_CFG_USE_DYNAMIC)
+#define CH_CFG_USE_DYNAMIC TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Objects factory options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Objects Factory APIs.
+ * @details If enabled then the objects factory APIs are included in the
+ * kernel.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_CFG_USE_FACTORY)
+#define CH_CFG_USE_FACTORY TRUE
+#endif
+
+/**
+ * @brief Maximum length for object names.
+ * @details If the specified length is zero then the name is stored by
+ * pointer but this could have unintended side effects.
+ */
+#if !defined(CH_CFG_FACTORY_MAX_NAMES_LENGTH)
+#define CH_CFG_FACTORY_MAX_NAMES_LENGTH 8
+#endif
+
+/**
+ * @brief Enables the registry of generic objects.
+ */
+#if !defined(CH_CFG_FACTORY_OBJECTS_REGISTRY)
+#define CH_CFG_FACTORY_OBJECTS_REGISTRY TRUE
+#endif
+
+/**
+ * @brief Enables factory for generic buffers.
+ */
+#if !defined(CH_CFG_FACTORY_GENERIC_BUFFERS)
+#define CH_CFG_FACTORY_GENERIC_BUFFERS TRUE
+#endif
+
+/**
+ * @brief Enables factory for semaphores.
+ */
+#if !defined(CH_CFG_FACTORY_SEMAPHORES)
+#define CH_CFG_FACTORY_SEMAPHORES TRUE
+#endif
+
+/**
+ * @brief Enables factory for mailboxes.
+ */
+#if !defined(CH_CFG_FACTORY_MAILBOXES)
+#define CH_CFG_FACTORY_MAILBOXES TRUE
+#endif
+
+/**
+ * @brief Enables factory for objects FIFOs.
+ */
+#if !defined(CH_CFG_FACTORY_OBJ_FIFOS)
+#define CH_CFG_FACTORY_OBJ_FIFOS TRUE
+#endif
+
+/**
+ * @brief Enables factory for Pipes.
+ */
+#if !defined(CH_CFG_FACTORY_PIPES) || defined(__DOXYGEN__)
+#define CH_CFG_FACTORY_PIPES TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Debug option, kernel statistics.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_STATISTICS)
+#define CH_DBG_STATISTICS FALSE
+#endif
+
+/**
+ * @brief Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ * at runtime.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_SYSTEM_STATE_CHECK)
+#define CH_DBG_SYSTEM_STATE_CHECK FALSE
+#endif
+
+/**
+ * @brief Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ * parameters are activated.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_ENABLE_CHECKS)
+#define CH_DBG_ENABLE_CHECKS FALSE
+#endif
+
+/**
+ * @brief Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ * activated. This includes consistency checks inside the kernel,
+ * runtime anomalies and port-defined checks.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_ENABLE_ASSERTS)
+#define CH_DBG_ENABLE_ASSERTS FALSE
+#endif
+
+/**
+ * @brief Debug option, trace buffer.
+ * @details If enabled then the trace buffer is activated.
+ *
+ * @note The default is @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#if !defined(CH_DBG_TRACE_MASK)
+#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED
+#endif
+
+/**
+ * @brief Trace buffer entries.
+ * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
+ * different from @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#if !defined(CH_DBG_TRACE_BUFFER_SIZE)
+#define CH_DBG_TRACE_BUFFER_SIZE 128
+#endif
+
+/**
+ * @brief Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note The default is @p FALSE.
+ * @note The stack check is performed in a architecture/port dependent way.
+ * It may not be implemented or some ports.
+ * @note The default failure mode is to halt the system with the global
+ * @p panic_msg variable set to @p NULL.
+ */
+#if !defined(CH_DBG_ENABLE_STACK_CHECK)
+#define CH_DBG_ENABLE_STACK_CHECK FALSE
+#endif
+
+/**
+ * @brief Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ * value when a thread is created. This can be useful for the
+ * runtime measurement of the used stack.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_FILL_THREADS)
+#define CH_DBG_FILL_THREADS FALSE
+#endif
+
+/**
+ * @brief Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p thread_t structure that
+ * counts the system ticks occurred while executing the thread.
+ *
+ * @note The default is @p FALSE.
+ * @note This debug option is not currently compatible with the
+ * tickless mode.
+ */
+#if !defined(CH_DBG_THREADS_PROFILING)
+#define CH_DBG_THREADS_PROFILING FALSE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief System structure extension.
+ * @details User fields added to the end of the @p ch_system_t structure.
+ */
+#define CH_CFG_SYSTEM_EXTRA_FIELDS \
+ /* Add threads custom fields here.*/
+
+/**
+ * @brief System initialization hook.
+ * @details User initialization code added to the @p chSysInit() function
+ * just before interrupts are enabled globally.
+ */
+#define CH_CFG_SYSTEM_INIT_HOOK() { \
+ /* Add threads initialization code here.*/ \
+}
+
+/**
+ * @brief Threads descriptor structure extension.
+ * @details User fields added to the end of the @p thread_t structure.
+ */
+#define CH_CFG_THREAD_EXTRA_FIELDS \
+ /* Add threads custom fields here.*/
+
+/**
+ * @brief Threads initialization hook.
+ * @details User initialization code added to the @p _thread_init() function.
+ *
+ * @note It is invoked from within @p _thread_init() and implicitly from all
+ * the threads creation APIs.
+ */
+#define CH_CFG_THREAD_INIT_HOOK(tp) { \
+ /* Add threads initialization code here.*/ \
+}
+
+/**
+ * @brief Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ */
+#define CH_CFG_THREAD_EXIT_HOOK(tp) { \
+ /* Add threads finalization code here.*/ \
+}
+
+/**
+ * @brief Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \
+ /* Context switch code here.*/ \
+}
+
+/**
+ * @brief ISR enter hook.
+ */
+#define CH_CFG_IRQ_PROLOGUE_HOOK() { \
+ /* IRQ prologue code here.*/ \
+}
+
+/**
+ * @brief ISR exit hook.
+ */
+#define CH_CFG_IRQ_EPILOGUE_HOOK() { \
+ /* IRQ epilogue code here.*/ \
+}
+
+/**
+ * @brief Idle thread enter hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to activate a power saving mode.
+ */
+#define CH_CFG_IDLE_ENTER_HOOK() { \
+ /* Idle-enter code here.*/ \
+}
+
+/**
+ * @brief Idle thread leave hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to deactivate a power saving mode.
+ */
+#define CH_CFG_IDLE_LEAVE_HOOK() { \
+ /* Idle-leave code here.*/ \
+}
+
+/**
+ * @brief Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#define CH_CFG_IDLE_LOOP_HOOK() { \
+ /* Idle loop code here.*/ \
+}
+
+/**
+ * @brief System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ * after processing the virtual timers queue.
+ */
+#define CH_CFG_SYSTEM_TICK_HOOK() { \
+ /* System tick event code here.*/ \
+}
+
+/**
+ * @brief System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ * the system is halted.
+ */
+#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \
+ /* System halt code here.*/ \
+}
+
+/**
+ * @brief Trace hook.
+ * @details This hook is invoked each time a new record is written in the
+ * trace buffer.
+ */
+#define CH_CFG_TRACE_HOOK(tep) { \
+ /* Trace code here.*/ \
+}
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h). */
+/*===========================================================================*/
+
+#endif /* CHCONF_H */
+
+/** @} */
diff --git a/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/ffconf.h b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/ffconf.h new file mode 100644 index 000000000..944ffde25 --- /dev/null +++ b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/ffconf.h @@ -0,0 +1,272 @@ +/* CHIBIOS FIX */
+#include "ch.h"
+
+/*---------------------------------------------------------------------------/
+/ FatFs - Configuration file
+/---------------------------------------------------------------------------*/
+
+#define FFCONF_DEF 87030 /* Revision ID */
+
+/*---------------------------------------------------------------------------/
+/ Function Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_FS_READONLY 0
+/* This option switches read-only configuration. (0:Read/Write or 1:Read-only)
+/ Read-only configuration removes writing API functions, f_write(), f_sync(),
+/ f_unlink(), f_mkdir(), f_chmod(), f_rename(), f_truncate(), f_getfree()
+/ and optional writing functions as well. */
+
+
+#define FF_FS_MINIMIZE 0
+/* This option defines minimization level to remove some basic API functions.
+/
+/ 0: All basic functions are enabled.
+/ 1: f_stat(), f_getfree(), f_unlink(), f_mkdir(), f_truncate() and f_rename()
+/ are removed.
+/ 2: f_opendir(), f_readdir() and f_closedir() are removed in addition to 1.
+/ 3: f_lseek() function is removed in addition to 2. */
+
+
+#define FF_USE_STRFUNC 0
+/* This option switches string functions, f_gets(), f_putc(), f_puts() and f_printf().
+/
+/ 0: Disable string functions.
+/ 1: Enable without LF-CRLF conversion.
+/ 2: Enable with LF-CRLF conversion. */
+
+
+#define FF_USE_FIND 0
+/* This option switches filtered directory read functions, f_findfirst() and
+/ f_findnext(). (0:Disable, 1:Enable 2:Enable with matching altname[] too) */
+
+
+#define FF_USE_MKFS 0
+/* This option switches f_mkfs() function. (0:Disable or 1:Enable) */
+
+
+#define FF_USE_FASTSEEK 0
+/* This option switches fast seek function. (0:Disable or 1:Enable) */
+
+
+#define FF_USE_EXPAND 0
+/* This option switches f_expand function. (0:Disable or 1:Enable) */
+
+
+#define FF_USE_CHMOD 0
+/* This option switches attribute manipulation functions, f_chmod() and f_utime().
+/ (0:Disable or 1:Enable) Also FF_FS_READONLY needs to be 0 to enable this option. */
+
+
+#define FF_USE_LABEL 0
+/* This option switches volume label functions, f_getlabel() and f_setlabel().
+/ (0:Disable or 1:Enable) */
+
+
+#define FF_USE_FORWARD 0
+/* This option switches f_forward() function. (0:Disable or 1:Enable) */
+
+
+/*---------------------------------------------------------------------------/
+/ Locale and Namespace Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_CODE_PAGE 850
+/* This option specifies the OEM code page to be used on the target system.
+/ Incorrect code page setting can cause a file open failure.
+/
+/ 437 - U.S.
+/ 720 - Arabic
+/ 737 - Greek
+/ 771 - KBL
+/ 775 - Baltic
+/ 850 - Latin 1
+/ 852 - Latin 2
+/ 855 - Cyrillic
+/ 857 - Turkish
+/ 860 - Portuguese
+/ 861 - Icelandic
+/ 862 - Hebrew
+/ 863 - Canadian French
+/ 864 - Arabic
+/ 865 - Nordic
+/ 866 - Russian
+/ 869 - Greek 2
+/ 932 - Japanese (DBCS)
+/ 936 - Simplified Chinese (DBCS)
+/ 949 - Korean (DBCS)
+/ 950 - Traditional Chinese (DBCS)
+/ 0 - Include all code pages above and configured by f_setcp()
+*/
+
+
+#define FF_USE_LFN 3
+#define FF_MAX_LFN 255
+/* The FF_USE_LFN switches the support for LFN (long file name).
+/
+/ 0: Disable LFN. FF_MAX_LFN has no effect.
+/ 1: Enable LFN with static working buffer on the BSS. Always NOT thread-safe.
+/ 2: Enable LFN with dynamic working buffer on the STACK.
+/ 3: Enable LFN with dynamic working buffer on the HEAP.
+/
+/ To enable the LFN, Unicode handling functions (option/unicode.c) must be added
+/ to the project. The working buffer occupies (FF_MAX_LFN + 1) * 2 bytes and
+/ additional 608 bytes at exFAT enabled. FF_MAX_LFN can be in range from 12 to 255.
+/ It should be set 255 to support full featured LFN operations.
+/ When use stack for the working buffer, take care on stack overflow. When use heap
+/ memory for the working buffer, memory management functions, ff_memalloc() and
+/ ff_memfree(), must be added to the project. */
+
+
+#define FF_LFN_UNICODE 0
+/* This option switches character encoding on the API, 0:ANSI/OEM or 1:UTF-16,
+/ when LFN is enabled. Also behavior of string I/O functions will be affected by
+/ this option. When LFN is not enabled, this option has no effect.
+*/
+
+
+#define FF_STRF_ENCODE 3
+/* When FF_LFN_UNICODE = 1 with LFN enabled, string I/O functions, f_gets(),
+/ f_putc(), f_puts and f_printf() convert the character encoding in it.
+/ This option selects assumption of character encoding ON THE FILE to be
+/ read/written via those functions.
+/
+/ 0: ANSI/OEM
+/ 1: UTF-16LE
+/ 2: UTF-16BE
+/ 3: UTF-8
+*/
+
+
+#define FF_FS_RPATH 0
+/* This option configures support for relative path.
+/
+/ 0: Disable relative path and remove related functions.
+/ 1: Enable relative path. f_chdir() and f_chdrive() are available.
+/ 2: f_getcwd() function is available in addition to 1.
+*/
+
+
+/*---------------------------------------------------------------------------/
+/ Drive/Volume Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_VOLUMES 1
+/* Number of volumes (logical drives) to be used. (1-10) */
+
+
+#define FF_STR_VOLUME_ID 0
+#define FF_VOLUME_STRS "RAM","NAND","CF","SD","SD2","USB","USB2","USB3"
+/* FF_STR_VOLUME_ID switches string support for volume ID.
+/ When FF_STR_VOLUME_ID is set to 1, also pre-defined strings can be used as drive
+/ number in the path name. FF_VOLUME_STRS defines the drive ID strings for each
+/ logical drives. Number of items must be equal to FF_VOLUMES. Valid characters for
+/ the drive ID strings are: A-Z and 0-9. */
+
+
+#define FF_MULTI_PARTITION 0
+/* This option switches support for multiple volumes on the physical drive.
+/ By default (0), each logical drive number is bound to the same physical drive
+/ number and only an FAT volume found on the physical drive will be mounted.
+/ When this function is enabled (1), each logical drive number can be bound to
+/ arbitrary physical drive and partition listed in the VolToPart[]. Also f_fdisk()
+/ funciton will be available. */
+
+
+#define FF_MIN_SS 512
+#define FF_MAX_SS 512
+/* This set of options configures the range of sector size to be supported. (512,
+/ 1024, 2048 or 4096) Always set both 512 for most systems, generic memory card and
+/ harddisk. But a larger value may be required for on-board flash memory and some
+/ type of optical media. When FF_MAX_SS is larger than FF_MIN_SS, FatFs is configured
+/ for variable sector size mode and disk_ioctl() function needs to implement
+/ GET_SECTOR_SIZE command. */
+
+
+#define FF_USE_TRIM 0
+/* This option switches support for ATA-TRIM. (0:Disable or 1:Enable)
+/ To enable Trim function, also CTRL_TRIM command should be implemented to the
+/ disk_ioctl() function. */
+
+
+#define FF_FS_NOFSINFO 0
+/* If you need to know correct free space on the FAT32 volume, set bit 0 of this
+/ option, and f_getfree() function at first time after volume mount will force
+/ a full FAT scan. Bit 1 controls the use of last allocated cluster number.
+/
+/ bit0=0: Use free cluster count in the FSINFO if available.
+/ bit0=1: Do not trust free cluster count in the FSINFO.
+/ bit1=0: Use last allocated cluster number in the FSINFO if available.
+/ bit1=1: Do not trust last allocated cluster number in the FSINFO.
+*/
+
+
+
+/*---------------------------------------------------------------------------/
+/ System Configurations
+/---------------------------------------------------------------------------*/
+
+#define FF_FS_TINY 0
+/* This option switches tiny buffer configuration. (0:Normal or 1:Tiny)
+/ At the tiny configuration, size of file object (FIL) is shrinked FF_MAX_SS bytes.
+/ Instead of private sector buffer eliminated from the file object, common sector
+/ buffer in the filesystem object (FATFS) is used for the file data transfer. */
+
+
+#define FF_FS_EXFAT 1
+/* This option switches support for exFAT filesystem. (0:Disable or 1:Enable)
+/ When enable exFAT, also LFN needs to be enabled.
+/ Note that enabling exFAT discards ANSI C (C89) compatibility. */
+
+
+#define FF_FS_NORTC 1
+#define FF_NORTC_MON 5
+#define FF_NORTC_MDAY 1
+#define FF_NORTC_YEAR 2017
+/* The option FF_FS_NORTC switches timestamp functiton. If the system does not have
+/ any RTC function or valid timestamp is not needed, set FF_FS_NORTC = 1 to disable
+/ the timestamp function. All objects modified by FatFs will have a fixed timestamp
+/ defined by FF_NORTC_MON, FF_NORTC_MDAY and FF_NORTC_YEAR in local time.
+/ To enable timestamp function (FF_FS_NORTC = 0), get_fattime() function need to be
+/ added to the project to read current time form real-time clock. FF_NORTC_MON,
+/ FF_NORTC_MDAY and FF_NORTC_YEAR have no effect.
+/ These options have no effect at read-only configuration (FF_FS_READONLY = 1). */
+
+
+#define FF_FS_LOCK 0
+/* The option FF_FS_LOCK switches file lock function to control duplicated file open
+/ and illegal operation to open objects. This option must be 0 when FF_FS_READONLY
+/ is 1.
+/
+/ 0: Disable file lock function. To avoid volume corruption, application program
+/ should avoid illegal open, remove and rename to the open objects.
+/ >0: Enable file lock function. The value defines how many files/sub-directories
+/ can be opened simultaneously under file lock control. Note that the file
+/ lock control is independent of re-entrancy. */
+
+
+#define FF_FS_REENTRANT 0
+#define FF_FS_TIMEOUT MS2ST(1000)
+#define FF_SYNC_t semaphore_t*
+/* The option FF_FS_REENTRANT switches the re-entrancy (thread safe) of the FatFs
+/ module itself. Note that regardless of this option, file access to different
+/ volume is always re-entrant and volume control functions, f_mount(), f_mkfs()
+/ and f_fdisk() function, are always not re-entrant. Only file/directory access
+/ to the same volume is under control of this function.
+/
+/ 0: Disable re-entrancy. FF_FS_TIMEOUT and FF_SYNC_t have no effect.
+/ 1: Enable re-entrancy. Also user provided synchronization handlers,
+/ ff_req_grant(), ff_rel_grant(), ff_del_syncobj() and ff_cre_syncobj()
+/ function, must be added to the project. Samples are available in
+/ option/syscall.c.
+/
+/ The FF_FS_TIMEOUT defines timeout period in unit of time tick.
+/ The FF_SYNC_t defines O/S dependent sync object type. e.g. HANDLE, ID, OS_EVENT*,
+/ SemaphoreHandle_t and etc. A header file for O/S definitions needs to be
+/ included somewhere in the scope of ff.h. */
+
+/* #include <windows.h> // O/S definitions */
+
+
+
+/*--- End of configuration options ---*/
diff --git a/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/halconf.h b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/halconf.h new file mode 100644 index 000000000..59b8fe277 --- /dev/null +++ b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/halconf.h @@ -0,0 +1,532 @@ +/*
+ ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/halconf.h
+ * @brief HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ * various device drivers from your application. You may also use
+ * this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef HALCONF_H
+#define HALCONF_H
+
+#define _CHIBIOS_HAL_CONF_
+#define _CHIBIOS_HAL_CONF_VER_6_0_
+
+#include "mcuconf.h"
+
+/**
+ * @brief Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL TRUE
+#endif
+
+/**
+ * @brief Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC FALSE
+#endif
+
+/**
+ * @brief Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN FALSE
+#endif
+
+/**
+ * @brief Enables the cryptographic subsystem.
+ */
+#if !defined(HAL_USE_CRY) || defined(__DOXYGEN__)
+#define HAL_USE_CRY FALSE
+#endif
+
+/**
+ * @brief Enables the DAC subsystem.
+ */
+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
+#define HAL_USE_DAC FALSE
+#endif
+
+/**
+ * @brief Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT FALSE
+#endif
+
+/**
+ * @brief Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT FALSE
+#endif
+
+/**
+ * @brief Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C FALSE
+#endif
+
+/**
+ * @brief Enables the I2S subsystem.
+ */
+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
+#define HAL_USE_I2S FALSE
+#endif
+
+/**
+ * @brief Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU FALSE
+#endif
+
+/**
+ * @brief Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC FALSE
+#endif
+
+/**
+ * @brief Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI FALSE
+#endif
+
+/**
+ * @brief Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM FALSE
+#endif
+
+/**
+ * @brief Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC FALSE
+#endif
+
+/**
+ * @brief Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC TRUE
+#endif
+
+/**
+ * @brief Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB TRUE
+#endif
+
+/**
+ * @brief Enables the SIO subsystem.
+ */
+#if !defined(HAL_USE_SIO) || defined(__DOXYGEN__)
+#define HAL_USE_SIO FALSE
+#endif
+
+/**
+ * @brief Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI FALSE
+#endif
+
+/**
+ * @brief Enables the TRNG subsystem.
+ */
+#if !defined(HAL_USE_TRNG) || defined(__DOXYGEN__)
+#define HAL_USE_TRNG FALSE
+#endif
+
+/**
+ * @brief Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART FALSE
+#endif
+
+/**
+ * @brief Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB TRUE
+#endif
+
+/**
+ * @brief Enables the WDG subsystem.
+ */
+#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
+#define HAL_USE_WDG FALSE
+#endif
+
+/**
+ * @brief Enables the WSPI subsystem.
+ */
+#if !defined(HAL_USE_WSPI) || defined(__DOXYGEN__)
+#define HAL_USE_WSPI FALSE
+#endif
+
+/*===========================================================================*/
+/* PAL driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(PAL_USE_CALLBACKS) || defined(__DOXYGEN__)
+#define PAL_USE_CALLBACKS FALSE
+#endif
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(PAL_USE_WAIT) || defined(__DOXYGEN__)
+#define PAL_USE_WAIT FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE TRUE
+#endif
+
+/**
+ * @brief Enforces the driver to use direct callbacks rather than OSAL events.
+ */
+#if !defined(CAN_ENFORCE_USE_CALLBACKS) || defined(__DOXYGEN__)
+#define CAN_ENFORCE_USE_CALLBACKS FALSE
+#endif
+
+/*===========================================================================*/
+/* CRY driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the SW fall-back of the cryptographic driver.
+ * @details When enabled, this option, activates a fall-back software
+ * implementation for algorithms not supported by the underlying
+ * hardware.
+ * @note Fall-back implementations may not be present for all algorithms.
+ */
+#if !defined(HAL_CRY_USE_FALLBACK) || defined(__DOXYGEN__)
+#define HAL_CRY_USE_FALLBACK FALSE
+#endif
+
+/**
+ * @brief Makes the driver forcibly use the fall-back implementations.
+ */
+#if !defined(HAL_CRY_ENFORCE_FALLBACK) || defined(__DOXYGEN__)
+#define HAL_CRY_ENFORCE_FALLBACK FALSE
+#endif
+
+/*===========================================================================*/
+/* DAC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(DAC_USE_WAIT) || defined(__DOXYGEN__)
+#define DAC_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p dacAcquireBus() and @p dacReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(DAC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define DAC_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the zero-copy API.
+ */
+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
+#define MAC_USE_ZERO_COPY FALSE
+#endif
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ * This option is recommended also if the SPI driver does not
+ * use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Number of initialization attempts before rejecting the card.
+ * @note Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY 100
+#endif
+
+/**
+ * @brief Include support for MMC cards.
+ * @note MMC support is not yet implemented so this option must be kept
+ * at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT FALSE
+#endif
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING TRUE
+#endif
+
+/**
+ * @brief OCR initialization constant for V20 cards.
+ */
+#if !defined(SDC_INIT_OCR_V20) || defined(__DOXYGEN__)
+#define SDC_INIT_OCR_V20 0x50FF8000U
+#endif
+
+/**
+ * @brief OCR initialization constant for non-V20 cards.
+ */
+#if !defined(SDC_INIT_OCR) || defined(__DOXYGEN__)
+#define SDC_INIT_OCR 0x80100000U
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ * default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE 38400
+#endif
+
+/**
+ * @brief Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ * buffers depending on the requirements of your application.
+ * @note The default is 16 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE 16
+#endif
+
+/*===========================================================================*/
+/* SERIAL_USB driver related setting. */
+/*===========================================================================*/
+
+/**
+ * @brief Serial over USB buffers size.
+ * @details Configuration parameter, the buffer size must be a multiple of
+ * the USB data endpoint maximum packet size.
+ * @note The default is 256 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_SIZE 256
+#endif
+
+/**
+ * @brief Serial over USB number of buffers.
+ * @note The default is 2 buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_NUMBER 2
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables circular transfers APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_CIRCULAR) || defined(__DOXYGEN__)
+#define SPI_USE_CIRCULAR FALSE
+#endif
+
+
+/**
+ * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/**
+ * @brief Handling method for SPI CS line.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_SELECT_MODE) || defined(__DOXYGEN__)
+#define SPI_SELECT_MODE SPI_SELECT_MODE_PAD
+#endif
+
+/*===========================================================================*/
+/* UART driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
+#define UART_USE_WAIT FALSE
+#endif
+
+/**
+ * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define UART_USE_MUTUAL_EXCLUSION FALSE
+#endif
+
+/*===========================================================================*/
+/* USB driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
+#define USB_USE_WAIT FALSE
+#endif
+
+/*===========================================================================*/
+/* WSPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(WSPI_USE_WAIT) || defined(__DOXYGEN__)
+#define WSPI_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p wspiAcquireBus() and @p wspiReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(WSPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define WSPI_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+#endif /* HALCONF_H */
+
+/** @} */
diff --git a/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/mcuconf.h b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/mcuconf.h new file mode 100644 index 000000000..a89194897 --- /dev/null +++ b/demos/STM32/RT-STM32F103-STM3210E_EVAL-FATFS-USB/cfg/mcuconf.h @@ -0,0 +1,214 @@ +/*
+ ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef MCUCONF_H
+#define MCUCONF_H
+
+#define STM32F103_MCUCONF
+
+/*
+ * STM32F103 drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0 Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3 Lowest...Highest.
+ */
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT FALSE
+#define STM32_HSI_ENABLED TRUE
+#define STM32_LSI_ENABLED FALSE
+#define STM32_HSE_ENABLED TRUE
+#define STM32_LSE_ENABLED FALSE
+#define STM32_SW STM32_SW_PLL
+#define STM32_PLLSRC STM32_PLLSRC_HSE
+#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1
+#define STM32_PLLMUL_VALUE 9
+#define STM32_HPRE STM32_HPRE_DIV1
+#define STM32_PPRE1 STM32_PPRE1_DIV2
+#define STM32_PPRE2 STM32_PPRE2_DIV2
+#define STM32_ADCPRE STM32_ADCPRE_DIV4
+#define STM32_USB_CLOCK_REQUIRED TRUE
+#define STM32_USBPRE STM32_USBPRE_DIV1P5
+#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
+#define STM32_RTCSEL STM32_RTCSEL_HSEDIV
+#define STM32_PVD_ENABLE FALSE
+#define STM32_PLS STM32_PLS_LEV0
+
+/*
+ * IRQ system settings.
+ */
+#define STM32_IRQ_EXTI0_PRIORITY 6
+#define STM32_IRQ_EXTI1_PRIORITY 6
+#define STM32_IRQ_EXTI2_PRIORITY 6
+#define STM32_IRQ_EXTI3_PRIORITY 6
+#define STM32_IRQ_EXTI4_PRIORITY 6
+#define STM32_IRQ_EXTI5_9_PRIORITY 6
+#define STM32_IRQ_EXTI10_15_PRIORITY 6
+#define STM32_IRQ_EXTI16_PRIORITY 6
+#define STM32_IRQ_EXTI17_PRIORITY 6
+#define STM32_IRQ_EXTI18_PRIORITY 6
+#define STM32_IRQ_EXTI19_PRIORITY 6
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_USE_ADC1 FALSE
+#define STM32_ADC_ADC1_DMA_PRIORITY 2
+#define STM32_ADC_ADC1_IRQ_PRIORITY 6
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1 FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY 11
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1 FALSE
+#define STM32_GPT_USE_TIM2 FALSE
+#define STM32_GPT_USE_TIM3 FALSE
+#define STM32_GPT_USE_TIM4 FALSE
+#define STM32_GPT_USE_TIM5 FALSE
+#define STM32_GPT_USE_TIM8 FALSE
+#define STM32_GPT_TIM1_IRQ_PRIORITY 7
+#define STM32_GPT_TIM2_IRQ_PRIORITY 7
+#define STM32_GPT_TIM3_IRQ_PRIORITY 7
+#define STM32_GPT_TIM4_IRQ_PRIORITY 7
+#define STM32_GPT_TIM5_IRQ_PRIORITY 7
+#define STM32_GPT_TIM8_IRQ_PRIORITY 7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1 FALSE
+#define STM32_I2C_USE_I2C2 FALSE
+#define STM32_I2C_BUSY_TIMEOUT 50
+#define STM32_I2C_I2C1_IRQ_PRIORITY 5
+#define STM32_I2C_I2C2_IRQ_PRIORITY 5
+#define STM32_I2C_I2C1_DMA_PRIORITY 3
+#define STM32_I2C_I2C2_DMA_PRIORITY 3
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1 FALSE
+#define STM32_ICU_USE_TIM2 FALSE
+#define STM32_ICU_USE_TIM3 FALSE
+#define STM32_ICU_USE_TIM4 FALSE
+#define STM32_ICU_USE_TIM5 FALSE
+#define STM32_ICU_USE_TIM8 FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY 7
+#define STM32_ICU_TIM2_IRQ_PRIORITY 7
+#define STM32_ICU_TIM3_IRQ_PRIORITY 7
+#define STM32_ICU_TIM4_IRQ_PRIORITY 7
+#define STM32_ICU_TIM5_IRQ_PRIORITY 7
+#define STM32_ICU_TIM8_IRQ_PRIORITY 7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED FALSE
+#define STM32_PWM_USE_TIM1 FALSE
+#define STM32_PWM_USE_TIM2 FALSE
+#define STM32_PWM_USE_TIM3 FALSE
+#define STM32_PWM_USE_TIM4 FALSE
+#define STM32_PWM_USE_TIM5 FALSE
+#define STM32_PWM_USE_TIM8 FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY 7
+#define STM32_PWM_TIM2_IRQ_PRIORITY 7
+#define STM32_PWM_TIM3_IRQ_PRIORITY 7
+#define STM32_PWM_TIM4_IRQ_PRIORITY 7
+#define STM32_PWM_TIM5_IRQ_PRIORITY 7
+#define STM32_PWM_TIM8_IRQ_PRIORITY 7
+
+/*
+ * RTC driver system settings.
+ */
+#define STM32_RTC_IRQ_PRIORITY 15
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1 FALSE
+#define STM32_SERIAL_USE_USART2 FALSE
+#define STM32_SERIAL_USE_USART3 FALSE
+#define STM32_SERIAL_USE_UART4 FALSE
+#define STM32_SERIAL_USE_UART5 FALSE
+#define STM32_SERIAL_USART1_PRIORITY 12
+#define STM32_SERIAL_USART2_PRIORITY 12
+#define STM32_SERIAL_USART3_PRIORITY 12
+#define STM32_SERIAL_UART4_PRIORITY 12
+#define STM32_SERIAL_UART5_PRIORITY 12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1 FALSE
+#define STM32_SPI_USE_SPI2 FALSE
+#define STM32_SPI_USE_SPI3 FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY 1
+#define STM32_SPI_SPI2_DMA_PRIORITY 1
+#define STM32_SPI_SPI3_DMA_PRIORITY 1
+#define STM32_SPI_SPI1_IRQ_PRIORITY 10
+#define STM32_SPI_SPI2_IRQ_PRIORITY 10
+#define STM32_SPI_SPI3_IRQ_PRIORITY 10
+#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY 8
+#define STM32_ST_USE_TIMER 2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1 FALSE
+#define STM32_UART_USE_USART2 FALSE
+#define STM32_UART_USE_USART3 FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY 12
+#define STM32_UART_USART2_IRQ_PRIORITY 12
+#define STM32_UART_USART3_IRQ_PRIORITY 12
+#define STM32_UART_USART1_DMA_PRIORITY 0
+#define STM32_UART_USART2_DMA_PRIORITY 0
+#define STM32_UART_USART3_DMA_PRIORITY 0
+#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1 TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
+
+/*
+ * WDG driver system settings.
+ */
+#define STM32_WDG_USE_IWDG FALSE
+
+#endif /* MCUCONF_H */
|