diff options
Diffstat (limited to 'boards/OLIMEX_STM32_P107/board.h')
| -rw-r--r-- | boards/OLIMEX_STM32_P107/board.h | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/boards/OLIMEX_STM32_P107/board.h b/boards/OLIMEX_STM32_P107/board.h new file mode 100644 index 000000000..8bf523d33 --- /dev/null +++ b/boards/OLIMEX_STM32_P107/board.h @@ -0,0 +1,193 @@ +/*
+ ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for the Olimex STM32-P107 Rev.A evaluation board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_OLIMEX_STM32_P107_REV_A
+#define BOARD_NAME "Olimex STM32-P107 Rev.A"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK 32768
+#define STM32_HSECLK 25000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F10X_CL
+
+/*
+ * Ethernet PHY type.
+ */
+#define BOARD_PHY_ID MII_STE101P_ID
+#define BOARD_PHY_RMII
+
+/*
+ * IO pins assignments.
+ */
+#define GPIOA_SWITCH_WKUP 0
+#define GPIOA_SPI3_CS_MMC 4
+#define GPIOC_LED_STATUS1 6
+#define GPIOC_LED_STATUS2 7
+#define GPIOC_SWITCH_TAMPER 13
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ * 0 - Analog input.
+ * 1 - Push Pull output 10MHz.
+ * 2 - Push Pull output 2MHz.
+ * 3 - Push Pull output 50MHz.
+ * 4 - Digital input.
+ * 5 - Open Drain output 10MHz.
+ * 6 - Open Drain output 2MHz.
+ * 7 - Open Drain output 50MHz.
+ * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ * 9 - Alternate Push Pull output 10MHz.
+ * A - Alternate Push Pull output 2MHz.
+ * B - Alternate Push Pull output 50MHz.
+ * C - Reserved.
+ * D - Alternate Open Drain output 10MHz.
+ * E - Alternate Open Drain output 2MHz.
+ * F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ * PA0 - Normal input (WKUP BUTTON).
+ * PA1 - Normal input (ETH_RMII_REF_CLK).
+ * PA2 - Alternate output (ETH_RMII_MDIO).
+ * PA3 - Input with PU (unconnected).
+ * PA4 - Open Drain output (CS_MMC).
+ * PA5 - Input with PU (unconnected).
+ * PA6 - Input with PU (unconnected).
+ * PA7 - Normal input (ETH_RMII_CRS_DV).
+ * PA8 - Alternate output (MCO).
+ * PA9 - Normal input (OTG_VBUS).
+ * PA10 - Normal input (OTG_ID).
+ * PA11 - Normal input (OTG_DM).
+ * PA12 - Normal input (OTG_DP).
+ * PA13 - Normal input (TMS).
+ * PA14 - Normal input (TCK).
+ * PA15 - Normal input (TDI).
+ */
+#define VAL_GPIOACRL 0x48878B44 /* PA7...PA0 */
+#define VAL_GPIOACRH 0x4444444B /* PA15...PA8 */
+#define VAL_GPIOAODR 0xFFFFFFFF
+
+/*
+ * Port B setup:
+ * PB0 - Input with PU (unconnected).
+ * PB1 - Input with PU (unconnected).
+ * PB2 - Normal input (BOOT1).
+ * PB3 - Normal input (TDO).
+ * PB4 - Normal input (TRST).
+ * PB5 - Input with PU (unconnected).
+ * PB6 - Input with PU (unconnected).
+ * PB7 - Input with PU (unconnected).
+ * PB8 - Alternate O.D. (I2C1 SCL, remapped).
+ * PB9 - Alternate O.D. (I2C1 SDA, remapped).
+ * PB10 - Input with PU (unconnected).
+ * PB11 - Alternate output (ETH_RMII_TX_EN).
+ * PB12 - Alternate output (ETH_RMII_TXD0).
+ * PB13 - Alternate output (ETH_RMII_TXD1).
+ * PB14 - Input with PU (unconnected).
+ * PB15 - Push Pull output (CS_UEXT).
+ */
+#define VAL_GPIOBCRL 0x88844488 /* PB7...PB0 */
+#define VAL_GPIOBCRH 0x38BBB8FF /* PB15...PB8 */
+#define VAL_GPIOBODR 0xFFFFFFFF
+
+/*
+ * Port C setup:
+ * PC0 - Input with PU (unconnected).
+ * PC1 - Alternate output (ETH_MDC).
+ * PC2 - Input with PU (unconnected).
+ * PC3 - Input with PU (unconnected).
+ * PC4 - Normal input (ETH_RMII_RXD0).
+ * PC5 - Normal input (ETH_RMII_RXD1).
+ * PC6 - Push Pull output (STAT1 green LED).
+ * PC7 - Push Pull output (STAT2 yellow LED).
+ * PC8 - Input with PU (unconnected).
+ * PC9 - Input with PU (unconnected).
+ * PC10 - Alternate output (SPI3 SCK).
+ * PC11 - Input with PU (SPI3 MISO).
+ * PC12 - Alternate output (SPI3 MOSI).
+ * PC13 - Normal input (TAMPER).
+ * PC14 - Normal input (OSC32 IN).
+ * PC15 - Normal input (OSC32 OUT).
+ */
+#define VAL_GPIOCCRL 0x334488B8 /* PC7...PC0 */
+#define VAL_GPIOCCRH 0x444B8B88 /* PC15...PC8 */
+#define VAL_GPIOCODR 0xFFFFFF3F
+
+/*
+ * Port D setup:
+ * PD0 - Input with PU (unconnected).
+ * PD1 - Input with PU (unconnected).
+ * PD2 - Input with PU (unconnected).
+ * PD3 - Input with PU (unconnected).
+ * PD4 - Input with PU (unconnected).
+ * PD5 - Alternate output (USART2 TX, UEXT).
+ * PD6 - Input with PU (USART2 RX, UEXT).
+ * PD7 - Push Pull output (USB_VBUSON).
+ * PD8 - Alternate output (USART2 TX, remapped).
+ * PD9 - Normal input (USART2 RX, remapped).
+ * PD10 - Input with PU (unconnected).
+ * PD11 - Normal input (USART2 CTS, remapped).
+ * PD12 - Alternate output (USART2 RTS, remapped).
+ * PD13 - Input with PU (unconnected).
+ * PD14 - Input with PU (unconnected).
+ * PD15 - Input with PU (unconnected).
+ */
+#define VAL_GPIODCRL 0x38B88888 /* PD7...PD0 */
+#define VAL_GPIODCRH 0x888B484B /* PD15...PD8 */
+#define VAL_GPIODODR 0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ * PE14 - Normal input (ETH_RMII_MDINT).
+ * PE15 - Normal input (USB_FAULT).
+ */
+#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
+#define VAL_GPIOECRH 0x44888888 /* PE15...PE8 */
+#define VAL_GPIOEODR 0xFFFFFFFF
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+ void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
|