git-svn-id: svn://svn.code.sf.net/p/chibios/svn/trunk@2381 35acf78f-673a-0410-8e92-d51de3d6d3f4

1 files changed, 0 insertions, 123 deletions

diff --git a/os/hal/platforms/STM8/platform.dox b/os/hal/platforms/STM8/platform.dox
deleted file mode 100644
index 2bf6f73a3..000000000
--- a/os/hal/platforms/STM8/platform.dox
+++ /dev/null
@@ -1,123 +0,0 @@
-/*

-    ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010 Giovanni Di Sirio.

-

-    This file is part of ChibiOS/RT.

-

-    ChibiOS/RT is free software; you can redistribute it and/or modify

-    it under the terms of the GNU General Public License as published by

-    the Free Software Foundation; either version 3 of the License, or

-    (at your option) any later version.

-

-    ChibiOS/RT is distributed in the hope that it will be useful,

-    but WITHOUT ANY WARRANTY; without even the implied warranty of

-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

-    GNU General Public License for more details.

-

-    You should have received a copy of the GNU General Public License

-    along with this program.  If not, see <http://www.gnu.org/licenses/>.

-*/

-

-/**

- * @defgroup STM8S STM8Sx Drivers

- * @details This section describes all the supported drivers on the STM8S

- *          platform and the implementation details of the single drivers.

- *

- * @ingroup platforms

- */

-

-/**

- * @defgroup STM8S_HAL STM8S Initialization Support

- * @details The STM8S HAL support is responsible for system initialization.

- *

- * @section stm8s_hal_1 Supported HW resources

- * - CLK.

- * .

- * @section stm8s_hal_2 STM8S HAL driver implementation features

- * - Clock tree initialization.

- * - Clock source selection.

- * .

- * @ingroup STM8S

- */

-

-/**

- * @defgroup STM8S_PAL STM8S GPIO Support

- * @details The STM8S PAL driver uses the GPIO peripherals.

- *

- * @section stm8s_pal_1 Supported HW resources

- * - AFIO.

- * - GPIOA.

- * - GPIOB.

- * - GPIOC.

- * - GPIOD.

- * - GPIOE.

- * - GPIOF.

- * - GPIOG (where present).

- * - GPIOH (where present).

- * - GPIOI (where present).

- * .

- * @section stm8s_pal_2 STM8S PAL driver implementation features

- * The PAL driver implementation fully supports the following hardware

- * capabilities:

- * - 8 bits wide ports.

- * - Atomic set/reset/toggle functions because special STM8S instruction set.

- * - Output latched regardless of the pad setting.

- * - Direct read of input pads regardless of the pad setting.

- * .

- * @section stm8s_pal_3 Supported PAL setup modes

- * The STM8S PAL driver supports the following I/O modes:

- * - @p PAL_MODE_RESET.

- * - @p PAL_MODE_UNCONNECTED.

- * - @p PAL_MODE_INPUT.

- * - @p PAL_MODE_INPUT_PULLUP.

- * - @p PAL_MODE_OUTPUT_PUSHPULL.

- * - @p PAL_MODE_OUTPUT_OPENDRAIN.

- * .

- * Any attempt to setup an invalid mode is ignored.

- *

- * @section stm8s_pal_4 Suboptimal behavior

- * The STM8S GPIO is less than optimal in several areas, the limitations

- * should be taken in account while using the PAL driver:

- * - Bus/group writing is not atomic.

- * - Pad/group mode setup is not atomic.

- * .

- * @ingroup STM8S

- */

-

-/**

- * @defgroup STM8S_SPI STM8S SPI Support

- * @details The SPI driver supports the STM8S SPI peripheral in an interrupt

- *          driven implementation.

- * @note    Being the SPI a fast peripheral, much care must be taken to

- *          not saturate the CPU bandwidth with an excessive IRQ rate. The

- *          maximum transfer bit rate is likely limited by the IRQ

- *          handling.

- *

- * @section stm8s_spi_1 Supported HW resources

- * - SPI.

- * .

- * @section stm8s_spi_2 STM8S SPI driver implementation features

- * - Clock stop for reduced power usage when the driver is in stop state.

- * - Fully interrupt driven.

- * .

- * @ingroup STM8S

- */

-

-/**

- * @defgroup STM8S_SERIAL STM8S UART Support (buffered)

- * @details The STM8S Serial driver uses the UART peripherals in a

- *          buffered, interrupt driven, implementation.

- *

- * @section stm8s_serial_1 Supported HW resources

- * The serial driver can support any of the following hardware resources:

- * - UART1.

- * - UART2 (where present).

- * - UART3 (where present).

- * .

- * @section stm8s_serial_2 STM8S Serial driver implementation features

- * - Clock stop for reduced power usage when the driver is in stop state.

- * - Each UART can be independently enabled and programmed. Unused

- *   peripherals are left in low power mode.

- * - Fully interrupt driven.

- * .

- * @ingroup STM8S

- */