New board.

git-svn-id: svn://svn.code.sf.net/p/chibios/svn/trunk@8487 35acf78f-673a-0410-8e92-d51de3d6d3f4

3 files changed, 279 insertions, 0 deletions

diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.c b/os/hal/boards/ST_EVALKITST7580_1/board.c
new file mode 100644
index 000000000..eed5bb874
--- /dev/null
+++ b/os/hal/boards/ST_EVALKITST7580_1/board.c
@@ -0,0 +1,53 @@
+/*

+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

+

+    Licensed under the Apache License, Version 2.0 (the "License");

+    you may not use this file except in compliance with the License.

+    You may obtain a copy of the License at

+

+        http://www.apache.org/licenses/LICENSE-2.0

+

+    Unless required by applicable law or agreed to in writing, software

+    distributed under the License is distributed on an "AS IS" BASIS,

+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

+    See the License for the specific language governing permissions and

+    limitations under the License.

+*/

+

+/*

+   Concepts and parts of this file have been contributed by Rocco Marco

+   Guglielmi.

+ */

+#include "hal.h"

+

+/**

+ * @brief   PAL setup.

+ * @details Digital I/O ports static configuration as defined in @p board.h.

+ *          This variable is used by the HAL when initializing the PAL driver.

+ */

+#if HAL_USE_PAL || defined(__DOXYGEN__)

+const PALConfig pal_default_config =

+{

+  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},

+  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},

+  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},

+  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},

+  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},

+};

+#endif

+

+/*

+ * Early initialization code.

+ * This initialization must be performed just after stack setup and before

+ * any other initialization.

+ */

+void __early_init(void) {

+

+  stm32_clock_init();

+}

+

+/*

+ * Board-specific initialization code.

+ */

+void boardInit(void) {

+}

diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.h b/os/hal/boards/ST_EVALKITST7580_1/board.h
new file mode 100644
index 000000000..1ff513443
--- /dev/null
+++ b/os/hal/boards/ST_EVALKITST7580_1/board.h
@@ -0,0 +1,221 @@
+/*

+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

+

+    Licensed under the Apache License, Version 2.0 (the "License");

+    you may not use this file except in compliance with the License.

+    You may obtain a copy of the License at

+

+        http://www.apache.org/licenses/LICENSE-2.0

+

+    Unless required by applicable law or agreed to in writing, software

+    distributed under the License is distributed on an "AS IS" BASIS,

+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

+    See the License for the specific language governing permissions and

+    limitations under the License.

+*/

+

+/*

+   Concepts and parts of this file have been contributed by Rocco Marco

+   Guglielmi.

+ */

+#ifndef _BOARD_H_

+#define _BOARD_H_

+

+/*

+ * Setup for the ST7580 Evaluation kit board.

+ */

+

+/*

+ * Board identifier.

+ */

+#define BOARD_ST_EVALKIT_ST7580

+#define BOARD_NAME              "STMicroelectronics EVALKITST7580_1"

+

+/*

+ * Board frequencies.

+ */

+#define STM32_LSECLK            0

+#define STM32_HSECLK            8000000

+

+/*

+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.

+ */

+#define STM32F10X_MD

+

+/*

+ * IO pins assignments.

+ */

+#define GPIOA_CL_ADC            0

+#define GPIOA_PLC_T_REQ         1

+#define GPIOA_PLC_TXD           2

+#define GPIOA_PLC_RXD           3

+#define GPIOA_SD_NSS            4

+#define GPIOA_SD_SCLK           5

+#define GPIOA_SD_MISO           6

+#define GPIOA_SD_MOSI           7

+#define GPIOA_8MHZ_MCO          8

+#define GPIOA_UART1_TXD         9

+#define GPIOA_UART1_RXD         10

+#define GPIOA_USBDM             11

+#define GPIOA_USBDP             12

+#define GPIOA_JTMS              13

+#define GPIOA_JTCK              14

+#define GPIOA_JTDI              15

+

+#define GPIOB_SD_CD             0

+#define GPIOB_PA_ADC            1

+#define GPIOB_BOOT1             2

+#define GPIOB_J_TDO             3

+#define GPIOB_J_TRSTN           4

+#define GPIOB_LED_RED           5

+#define GPIOB_LED_YELLOW        6

+#define GPIOB_LED_GREEN         7

+#define GPIOB_I2C1_SCL          8

+#define GPIOB_I2C1_SDA          9

+#define GPIOB_SW4               10

+#define GPIOB_SW3               11

+#define GPIOB_DIP_SW4           12

+#define GPIOB_DIP_SW3           13

+#define GPIOB_DIP_SW2           14

+#define GPIOB_DIP_SW1           15

+

+#define GPIOC_PC0               0

+#define GPIOC_PC1               1

+#define GPIOC_PC2               2

+#define GPIOC_PC3               3

+#define GPIOC_PC4               4

+#define GPIOC_PC5               5

+#define GPIOC_PC6               6

+#define GPIOC_PC7               7

+#define GPIOC_PC8               8

+#define GPIOC_PC9               9

+#define GPIOC_PC10              10

+#define GPIOC_PC11              11

+#define GPIOC_PC12              12

+#define GPIOC_PL_RX_ON          13

+#define GPIOC_PL_TX_ON          14

+#define GPIOC_PLC_RESETN        15

+

+#define GPIOD_OSC_IN            0

+#define GPIOD_OSC_OUT           1

+

+/*

+ * I/O ports initial setup, this configuration is established soon after reset

+ * in the initialization code.

+ *

+ * The digits have the following meaning:

+ *   0 - Analog input.

+ *   1 - Push Pull output 10MHz.

+ *   2 - Push Pull output 2MHz.

+ *   3 - Push Pull output 50MHz.

+ *   4 - Digital input.

+ *   5 - Open Drain output 10MHz.

+ *   6 - Open Drain output 2MHz.

+ *   7 - Open Drain output 50MHz.

+ *   8 - Digital input with PullUp or PullDown resistor depending on ODR.

+ *   9 - Alternate Push Pull output 10MHz.

+ *   A - Alternate Push Pull output 2MHz.

+ *   B - Alternate Push Pull output 50MHz.

+ *   C - Reserved.

+ *   D - Alternate Open Drain output 10MHz.

+ *   E - Alternate Open Drain output 2MHz.

+ *   F - Alternate Open Drain output 50MHz.

+ * Please refer to the STM32 Reference Manual for details.

+ */

+

+/*

+ * Port A setup.

+ * PA0  - Analog input              (GPIOA_CL_ADC)

+ * PA1  - Push Pull output          (GPIOA_PLC_T_REQ).

+ * PA2  - Alternate output          (GPIOA_PLC_TXD).

+ * PA3  - Pull-up input             (GPIOA_PLC_RXD).

+ * PA4  - Push Pull output          (GPIOA_SD_NSS).

+ * PA5  - Alternate output          (GPIOA_SD_SCLK).

+ * PA6  - Alternate output          (GPIOA_SD_MISO).

+ * PA7  - Alternate output          (GPIOA_SD_MOSI).

+ * PA8  - Alternate output          (GPIOA_8MHZ_MCO).

+ * PA9  - Alternate output          (GPIOA_UART1_TXD).

+ * PA10 - Normal input              (GPIOA_UART1_RXD).

+ * PA11 - Alternate output          (GPIOA_USBDM).

+ * PA12 - Alternate output          (GPIOA_USBDP).

+ * PA13 - Pull-up input             (GPIOA_JTMS).

+ * PA14 - Pull-down input           (GPIOA_JTCK).

+ * PA15 - Pull-up input             (GPIOA_JTDI).

+ */

+#define VAL_GPIOACRL            0xBBB38B30      /*  PA7...PA0 */

+#define VAL_GPIOACRH            0x888BB4BB      /* PA15...PA8 */

+#define VAL_GPIOAODR            0xFFFFBFFF

+

+/*

+ * Port B setup.

+ * PB0  - Pull-up input             (GPIOB_SD_CD)

+ * PB1  - Analog input              (GPIOB_PA_ADC).

+ * PB2  - Normal input              (GPIOB_BOOT1).

+ * PB3  - Pull-up input             (GPIOB_J_TDO).

+ * PB4  - Pull-up input             (GPIOB_J_TRSTN).

+ * PB5  - Push Pull output          (GPIOB_LED_RED).

+ * PB6  - Push Pull output          (GPIOB_LED_YELLOW).

+ * PB7  - Push Pull output          (GPIOB_LED_GREEN).

+ * PB8  - Alternate output          (GPIOB_I2C1_SCL).

+ * PB9  - Alternate output          (GPIOB_I2C1_SDA).

+ * PB10 - Normal input              (GPIOB_SW4).

+ * PB11 - Normal input              (GPIOB_SW3).

+ * PB12 - Normal input              (GPIOB_DIP_SW4).

+ * PB13 - Normal input              (GPIOB_DIP_SW3).

+ * PB14 - Normal input              (GPIOB_DIP_SW2).

+ * PB15 - Normal input              (GPIOB_DIP_SW1).

+ */

+#define VAL_GPIOBCRL            0x33388408      /*  PB7...PB0 */

+#define VAL_GPIOBCRH            0x444444BB      /* PB15...PB8 */

+#define VAL_GPIOBODR            0xFFFFFFFF

+

+/*

+ * Port C setup.

+ * Everything input with pull-up except:

+ * PC13 - Normal input              (GPIOC_PL_RX_ON).

+ * PC14 - Normal input              (GPIOC_PL_TX_ON).

+ * PC15 - Push Pull output          (GPIOC_PLC_RESETN).

+ */

+#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */

+#define VAL_GPIOCCRH            0x34488888      /* PC15...PC8 */

+#define VAL_GPIOCODR            0xFFFFFFFF

+

+/*

+ * Port D setup.

+ * Everything input with pull-up except:

+ * PD0  - Normal input              (GPIOD_OSC_IN).

+ * PD1  - Normal input              (GPIOD_OSC_OUT).

+ */

+#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */

+#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */

+#define VAL_GPIODODR            0xFFFFFFFF

+

+/*

+ * Port E setup.

+ * Everything input with pull-up except:

+ */

+#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */

+#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */

+#define VAL_GPIOEODR            0xFFFFFFFF

+

+/*

+ * USB bus activation macro, required by the USB driver.

+ */

+#define usb_lld_connect_bus(usbp)

+

+/*

+ * USB bus de-activation macro, required by the USB driver.

+ */

+#define usb_lld_disconnect_bus(usbp)

+

+#if !defined(_FROM_ASM_)

+#ifdef __cplusplus

+extern "C" {

+#endif

+  void boardInit(void);

+#ifdef __cplusplus

+}

+#endif

+#endif /* _FROM_ASM_ */

+

+#endif /* _BOARD_H_ */

diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.mk b/os/hal/boards/ST_EVALKITST7580_1/board.mk
new file mode 100644
index 000000000..48775bb9c
--- /dev/null
+++ b/os/hal/boards/ST_EVALKITST7580_1/board.mk
@@ -0,0 +1,5 @@
+# List of all the board related files.

+BOARDSRC = ${CHIBIOS}/os/hal/boards/ST_EVALKITST7580_1/board.c

+

+# Required include directories

+BOARDINC = ${CHIBIOS}/os/hal/boards/ST_EVALKITST7580_1