git-svn-id: svn://svn.code.sf.net/p/chibios/svn/branches/kernel_3_dev@6126 35acf78f-673a-0410-8e92-d51de3d6d3f4

1 files changed, 0 insertions, 193 deletions

diff --git a/boards/OLIMEX_STM32_P107/board.h b/boards/OLIMEX_STM32_P107/board.h
deleted file mode 100644
index 8bf523d33..000000000
--- a/boards/OLIMEX_STM32_P107/board.h
+++ /dev/null
@@ -1,193 +0,0 @@
-/*

-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

-

-    Licensed under the Apache License, Version 2.0 (the "License");

-    you may not use this file except in compliance with the License.

-    You may obtain a copy of the License at

-

-        http://www.apache.org/licenses/LICENSE-2.0

-

-    Unless required by applicable law or agreed to in writing, software

-    distributed under the License is distributed on an "AS IS" BASIS,

-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

-    See the License for the specific language governing permissions and

-    limitations under the License.

-*/

-

-#ifndef _BOARD_H_

-#define _BOARD_H_

-

-/*

- * Setup for the Olimex STM32-P107 Rev.A evaluation board.

- */

-

-/*

- * Board identifier.

- */

-#define BOARD_OLIMEX_STM32_P107_REV_A

-#define BOARD_NAME              "Olimex STM32-P107 Rev.A"

-

-/*

- * Board frequencies.

- */

-#define STM32_LSECLK            32768

-#define STM32_HSECLK            25000000

-

-/*

- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.

- */

-#define STM32F10X_CL

-

-/*

- * Ethernet PHY type.

- */

-#define BOARD_PHY_ID            MII_STE101P_ID

-#define BOARD_PHY_RMII

-

-/*

- * IO pins assignments.

- */

-#define GPIOA_SWITCH_WKUP       0

-#define GPIOA_SPI3_CS_MMC       4

-#define GPIOC_LED_STATUS1       6

-#define GPIOC_LED_STATUS2       7

-#define GPIOC_SWITCH_TAMPER     13

-

-/*

- * I/O ports initial setup, this configuration is established soon after reset

- * in the initialization code.

- *

- * The digits have the following meaning:

- *   0 - Analog input.

- *   1 - Push Pull output 10MHz.

- *   2 - Push Pull output 2MHz.

- *   3 - Push Pull output 50MHz.

- *   4 - Digital input.

- *   5 - Open Drain output 10MHz.

- *   6 - Open Drain output 2MHz.

- *   7 - Open Drain output 50MHz.

- *   8 - Digital input with PullUp or PullDown resistor depending on ODR.

- *   9 - Alternate Push Pull output 10MHz.

- *   A - Alternate Push Pull output 2MHz.

- *   B - Alternate Push Pull output 50MHz.

- *   C - Reserved.

- *   D - Alternate Open Drain output 10MHz.

- *   E - Alternate Open Drain output 2MHz.

- *   F - Alternate Open Drain output 50MHz.

- * Please refer to the STM32 Reference Manual for details.

- */

-

-/*

- * Port A setup.

- * Everything input with pull-up except:

- * PA0  - Normal input      (WKUP BUTTON).

- * PA1  - Normal input      (ETH_RMII_REF_CLK).

- * PA2  - Alternate output  (ETH_RMII_MDIO).

- * PA3  - Input with PU     (unconnected).

- * PA4  - Open Drain output (CS_MMC).

- * PA5  - Input with PU     (unconnected).

- * PA6  - Input with PU     (unconnected).

- * PA7  - Normal input      (ETH_RMII_CRS_DV).

- * PA8  - Alternate output  (MCO).

- * PA9  - Normal input      (OTG_VBUS).

- * PA10 - Normal input      (OTG_ID).

- * PA11 - Normal input      (OTG_DM).

- * PA12 - Normal input      (OTG_DP).

- * PA13 - Normal input      (TMS).

- * PA14 - Normal input      (TCK).

- * PA15 - Normal input      (TDI).

- */

-#define VAL_GPIOACRL            0x48878B44      /*  PA7...PA0 */

-#define VAL_GPIOACRH            0x4444444B      /* PA15...PA8 */

-#define VAL_GPIOAODR            0xFFFFFFFF

-

-/*

- * Port B setup:

- * PB0  - Input with PU     (unconnected).

- * PB1  - Input with PU     (unconnected).

- * PB2  - Normal input      (BOOT1).

- * PB3  - Normal input      (TDO).

- * PB4  - Normal input      (TRST).

- * PB5  - Input with PU     (unconnected).

- * PB6  - Input with PU     (unconnected).

- * PB7  - Input with PU     (unconnected).

- * PB8  - Alternate O.D.    (I2C1 SCL, remapped).

- * PB9  - Alternate O.D.    (I2C1 SDA, remapped).

- * PB10 - Input with PU     (unconnected).

- * PB11 - Alternate output  (ETH_RMII_TX_EN).

- * PB12 - Alternate output  (ETH_RMII_TXD0).

- * PB13 - Alternate output  (ETH_RMII_TXD1).

- * PB14 - Input with PU     (unconnected).

- * PB15 - Push Pull output  (CS_UEXT).

- */

-#define VAL_GPIOBCRL            0x88844488      /*  PB7...PB0 */

-#define VAL_GPIOBCRH            0x38BBB8FF      /* PB15...PB8 */

-#define VAL_GPIOBODR            0xFFFFFFFF

-

-/*

- * Port C setup:

- * PC0  - Input with PU     (unconnected).

- * PC1  - Alternate output  (ETH_MDC).

- * PC2  - Input with PU     (unconnected).

- * PC3  - Input with PU     (unconnected).

- * PC4  - Normal input      (ETH_RMII_RXD0).

- * PC5  - Normal input      (ETH_RMII_RXD1).

- * PC6  - Push Pull output  (STAT1 green LED).

- * PC7  - Push Pull output  (STAT2 yellow LED).

- * PC8  - Input with PU     (unconnected).

- * PC9  - Input with PU     (unconnected).

- * PC10 - Alternate output  (SPI3 SCK).

- * PC11 - Input with PU     (SPI3 MISO).

- * PC12 - Alternate output  (SPI3 MOSI).

- * PC13 - Normal input      (TAMPER).

- * PC14 - Normal input      (OSC32 IN).

- * PC15 - Normal input      (OSC32 OUT).

- */

-#define VAL_GPIOCCRL            0x334488B8      /*  PC7...PC0 */

-#define VAL_GPIOCCRH            0x444B8B88      /* PC15...PC8 */

-#define VAL_GPIOCODR            0xFFFFFF3F

-

-/*

- * Port D setup:

- * PD0  - Input with PU     (unconnected).

- * PD1  - Input with PU     (unconnected).

- * PD2  - Input with PU     (unconnected).

- * PD3  - Input with PU     (unconnected).

- * PD4  - Input with PU     (unconnected).

- * PD5  - Alternate output  (USART2 TX, UEXT).

- * PD6  - Input with PU     (USART2 RX, UEXT).

- * PD7  - Push Pull output  (USB_VBUSON).

- * PD8  - Alternate output  (USART2 TX, remapped).

- * PD9  - Normal input      (USART2 RX, remapped).

- * PD10 - Input with PU     (unconnected).

- * PD11 - Normal input      (USART2 CTS, remapped).

- * PD12 - Alternate output  (USART2 RTS, remapped).

- * PD13 - Input with PU     (unconnected).

- * PD14 - Input with PU     (unconnected).

- * PD15 - Input with PU     (unconnected).

- */

-#define VAL_GPIODCRL            0x38B88888      /*  PD7...PD0 */

-#define VAL_GPIODCRH            0x888B484B      /* PD15...PD8 */

-#define VAL_GPIODODR            0xFFFFFFFF

-

-/*

- * Port E setup.

- * Everything input with pull-up except:

- * PE14 - Normal input      (ETH_RMII_MDINT).

- * PE15 - Normal input      (USB_FAULT).

- */

-#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */

-#define VAL_GPIOECRH            0x44888888      /* PE15...PE8 */

-#define VAL_GPIOEODR            0xFFFFFFFF

-

-#if !defined(_FROM_ASM_)

-#ifdef __cplusplus

-extern "C" {

-#endif

-  void boardInit(void);

-#ifdef __cplusplus

-}

-#endif

-#endif /* _FROM_ASM_ */

-

-#endif /* _BOARD_H_ */