blob: 03a7de55078aa6176aca64454d46176080377acb (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
|
/*
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _MCUCONF_H_
#define _MCUCONF_H_
/*
* STM32F0xx drivers configuration.
* The following settings override the default settings present in
* the various device driver implementation headers.
* Note that the settings for each driver only have effect if the whole
* driver is enabled in halconf.h.
*
* IRQ priorities:
* 3...0 Lowest...Highest.
*
* DMA priorities:
* 0...3 Lowest...Highest.
*/
#define KL2x_MCUCONF
/*
* HAL driver system settings.
*/
/* Select the MCU clocking mode below by enabling the appropriate block. */
/* FEI mode */
#if 0
#define KINETIS_MCG_MODE KINETIS_MCG_MODE_FEI
#define KINETIS_SYSCLK_FREQUENCY 21000000UL
#endif /* 0 */
/* FEE mode - 24 MHz with external 32.768 kHz crystal */
#if 0
#define KINETIS_MCG_MODE KINETIS_MCG_MODE_FEE
#define KINETIS_MCG_FLL_DMX32 1 /* Fine-tune for 32.768 kHz */
#define KINETIS_MCG_FLL_DRS 0 /* 732x FLL factor */
#define KINETIS_MCG_FLL_OUTDIV1 1 /* Divide 48 MHz FLL by 1 => 24 MHz */
#define KINETIS_MCG_FLL_OUTDIV4 2 /* Divide OUTDIV1 output by 2 => 12 MHz */
#define KINETIS_SYSCLK_FREQUENCY 23986176UL /* 32.768 kHz*732 (~24 MHz) */
#define KINETIS_UART0_CLOCK_FREQ (32768 * 732) /* FLL output */
#define KINETIS_UART0_CLOCK_SRC 1 /* Select FLL clock */
#define KINETIS_BUSCLK_FREQUENCY (KINETIS_SYSCLK_FREQUENCY / KINETIS_MCG_FLL_OUTDIV4)
#endif /* 0 */
/* FEE mode - 48 MHz */
#if 0
#define KINETIS_MCG_MODE KINETIS_MCG_MODE_FEE
#define KINETIS_MCG_FLL_DMX32 1 /* Fine-tune for 32.768 kHz */
#define KINETIS_MCG_FLL_DRS 1 /* 1464x FLL factor */
#define KINETIS_MCG_FLL_OUTDIV1 1 /* Divide 48 MHz FLL by 1 => 48 MHz */
#define KINETIS_MCG_FLL_OUTDIV4 2 /* Divide OUTDIV1 output by 2 => 24 MHz */
#define KINETIS_SYSCLK_FREQUENCY 47972352UL /* 32.768 kHz * 1464 (~48 MHz) */
#endif /* 0 */
/*
* SERIAL driver system settings.
*/
#define KINETIS_SERIAL_USE_UART0 FALSE
/*
* ADC driver system settings.
*/
#define KINETIS_ADC_USE_ADC0 TRUE
#endif /* _MCUCONF_H_ */
|
