1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
|
/*
Copyright (C) 2015 Fabio Utzig
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
/**
* @file pal_lld.c
* @brief NRF51822 PAL subsystem low level driver source.
*
* @addtogroup PAL
* @{
*/
#include "osal.h"
#include "hal.h"
#if (HAL_USE_PAL == TRUE) || defined(__DOXYGEN__)
/*===========================================================================*/
/* Driver local definitions. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver exported variables. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver local variables and types. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver local functions. */
/*===========================================================================*/
void _pal_lld_setpadmode(uint8_t pad, iomode_t mode)
{
uint8_t value = 0;
osalDbgAssert(pad < 32, "invalid pad");
switch (mode) {
case PAL_MODE_RESET:
case PAL_MODE_UNCONNECTED:
value = 2;
break;
case PAL_MODE_INPUT:
case PAL_MODE_INPUT_ANALOG:
value = 0;
break;
case PAL_MODE_INPUT_PULLUP:
value = 0xC;
break;
case PAL_MODE_INPUT_PULLDOWN:
value = 4;
break;
case PAL_MODE_OUTPUT_PUSHPULL:
value = 1;
break;
case PAL_MODE_OUTPUT_OPENDRAIN:
value = 0x61;
break;
}
NRF_GPIO->PIN_CNF[pad] = value;
}
/*===========================================================================*/
/* Driver interrupt handlers. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver exported functions. */
/*===========================================================================*/
/**
* @brief STM32 I/O ports configuration.
* @details Ports A-D(E, F, G, H) clocks enabled.
*
* @param[in] config the STM32 ports configuration
*
* @notapi
*/
void _pal_lld_init(const PALConfig *config)
{
uint8_t i;
for (i = 0; i < TOTAL_GPIO_PADS; i++) {
pal_lld_setpadmode(IOPORT1, i, config->pads[i]);
}
}
/**
* @brief Pads mode setup.
* @details This function programs a pads group belonging to the same port
* with the specified mode.
*
* @param[in] port the port identifier
* @param[in] mask the group mask
* @param[in] mode the mode
*
* @notapi
*/
void _pal_lld_setgroupmode(ioportid_t port,
ioportmask_t mask,
iomode_t mode)
{
uint8_t i;
(void)mask;
for (i = 0; i < TOTAL_GPIO_PADS; i++) {
pal_lld_setpadmode(port, i, mode);
}
}
#endif /* HAL_USE_PAL == TRUE */
/** @} */
|
