blob: 6b53f4b5f8640fe6c222e1643f7b9823760adf34 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
|
/*
ChibiOS - Copyright (C) 2016 Andrew Wygle aka awygle
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the Arduino Uno or board.
*/
/*
* Board identifier.
*/
#define BOARD_EXP430FR5959
#define BOARD_NAME "MSP430FR5969 LaunchPad"
/*
* IO lines assignments.
*/
#define LINE_LED_G PAL_LINE(IOPORT1, 0U)
#define LINE_LED_R PAL_LINE(IOPORT2, 14U)
#define LINE_SW_S1 PAL_LINE(IOPORT2, 13U)
#define LINE_SW_S2 PAL_LINE(IOPORT1, 1U)
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
* Please refer to the MSP430X Family Users Guide for details.
*/
/*
* Port A setup:
*
* P1.0 - Green LED (output low)
* P1.1 - Switch S2 (input pullup falling-edge interrupt)
* P1.2 - BoosterPack BP19 (input pullup)
* P1.3 - BoosterPack BP11 (input pullup)
* P1.4 - BoosterPack BP12 (input pullup)
* P1.5 - BoosterPack BP13 (input pullup)
* P1.6 - BoosterPack BP15 (input pullup)
* P1.7 - BoosterPack BP14 (input pullup)
* P2.0 - Application UART TX (alternate 2)
* P2.1 - Application UART RX (alternate 2)
* P2.2 - BoosterPack BP7 (input pullup)
* P2.3 - N/C (input pullup)
* P2.4 - BoosterPack BP6 (input pullup)
* P2.5 - BoosterPack BP4 (input pullup)
* P2.6 - BoosterPack BP3 (input pullup)
* P2.7 - N/C (input pullup)
*/
#define VAL_IOPORT1_OUT 0xFCFE
#define VAL_IOPORT1_DIR 0x0001
#define VAL_IOPORT1_REN 0xFCFE
#define VAL_IOPORT1_SEL0 0x0000
#define VAL_IOPORT1_SEL1 0x0300
#define VAL_IOPORT1_IES 0x0002
#define VAL_IOPORT1_IE 0x0002
/*
* Port B setup:
*
* P3.0 - BoosterPack BP18 (input pullup)
* P3.1 - N/C (input pullup)
* P3.2 - N/C (input pullup)
* P3.3 - N/C (input pullup)
* P3.4 - BoosterPack BP8 (input pullup)
* P3.5 - BoosterPack BP9 (input pullup)
* P3.6 - BoosterPack BP10 (input pullup)
* P3.7 - N/C (input pullup)
* P4.0 - Application UART CTS (input pullup falling-edge interrupt)
* P4.1 - Application UART RTS (output high)
* P4.2 - BoosterPack BP2 (input pullup)
* P4.3 - BoosterPack BP5 (input pullup)
* P4.4 - N/C (input pullup)
* P4.5 - Switch S1 (input pullup falling-edge interrupt)
* P4.6 - Red LED (output low)
* P4.7 - N/C (input pullup)
*/
#define VAL_IOPORT2_OUT 0xBFFF
#define VAL_IOPORT2_DIR 0x4200
#define VAL_IOPORT2_REN 0xBDFF
#define VAL_IOPORT2_SEL0 0x0000
#define VAL_IOPORT2_SEL1 0x0000
#define VAL_IOPORT2_IES 0x2100
#define VAL_IOPORT2_IE 0x2100
/*
* Port J setup:
*
* PJ.0 - TDO (input pullup)
* PJ.1 - TDI (input pullup)
* PJ.2 - TMS (input pullup)
* PJ.3 - TCK (input pullup)
* PJ.4 - LFXIN (alternate 1)
* PJ.5 - LFXOUT (alternate 1)
* PJ.6 - HFXIN (N/C) (input pullup)
* PJ.7 - HFXOUT (N/C) (input pullup)
*/
#define VAL_IOPORT0_OUT 0x00FF
#define VAL_IOPORT0_DIR 0x0000
#define VAL_IOPORT0_REN 0x00CF
#define VAL_IOPORT0_SEL0 0x0030
#define VAL_IOPORT0_SEL1 0x0000
#define VAL_IOPORT0_IES 0x0000
#define VAL_IOPORT0_IE 0x0000
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
