From 9b90dc05f58c619962e69e36d275b6ea56893496 Mon Sep 17 00:00:00 2001
From: Anderson Vulczak <andi@andi.com.br>
Date: Sat, 5 Oct 2019 10:44:55 -0300
Subject: ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)

This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).

The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.

- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)

Known issues:
 - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
   reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.

According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.

GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz

Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---
 .../ath79/dts/qca9563_tplink_archer-c6-v2-us.dts   | 130 +++++++++++++++++++++
 .../ath79/dts/qca9563_tplink_archer-c6-v2.dts      | 117 ++++++++++++++++++-
 .../ath79/dts/qca9563_tplink_archer-x6-v2.dtsi     | 120 +------------------
 .../ath79/generic/base-files/etc/board.d/01_leds   |   3 +-
 .../generic/base-files/etc/board.d/02_network      |   1 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |   3 +-
 target/linux/ath79/image/generic-tp-link.mk        |  16 ++-
 7 files changed, 270 insertions(+), 120 deletions(-)
 create mode 100644 target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts

(limited to 'target')

diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts
new file mode 100644
index 0000000000..3a6f00bf4e
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2-us.dts
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9563_tplink_archer-x6-v2.dtsi"
+
+/ {
+	compatible = "tplink,archer-c6-v2-us", "qca,qca9563";
+	model = "TP-Link Archer C6 v2 (US) / A6 v2 (US/TW)";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "tp-link:green:power";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wlan2g {
+			label = "tp-link:green:wlan2g";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wlan5g {
+			label = "tp-link:green:wlan5g";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		lan {
+			label = "tp-link:green:lan";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		wan {
+			label = "tp-link:green:wan";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_fail {
+			label = "tp-link:amber:wan";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "tp-link:green:wps";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "WPS button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "factory-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			mac: partition@20000 {
+				label = "mac";
+				reg = <0x020000 0x010000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "u-boot";
+				reg = <0x030000 0x020000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0xf80000>;
+			};
+
+			partition@fd0000 {
+				label = "tplink";
+				reg = <0xfd0000 0x020000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
index 5caec6fab1..e7ceec9b37 100644
--- a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
+++ b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
@@ -5,5 +5,120 @@
 
 / {
 	compatible = "tplink,archer-c6-v2", "qca,qca9563";
-	model = "TP-Link Archer C6 v2";
+	model = "TP-Link Archer C6 v2 (EU/RU/JP)";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "tp-link:green:power";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wlan2g {
+			label = "tp-link:green:wlan2g";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wlan5g {
+			label = "tp-link:green:wlan5g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		lan {
+			label = "tp-link:green:lan";
+			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+		};
+
+		wan {
+			label = "tp-link:green:wan";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_fail {
+			label = "tp-link:amber:wan";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "tp-link:green:wps";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "WPS button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			mac: partition@20000 {
+				label = "mac";
+				reg = <0x020000 0x010000>;
+				read-only;
+			};
+
+			partition@30000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x030000 0x7a0000>;
+			};
+
+			partition@7d0000 {
+				label = "tplink";
+				reg = <0x7d0000 0x020000>;
+				read-only;
+			};
+
+			art: partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
 };
diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
index f1a1f5673d..367f826b9d 100644
--- a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
+++ b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
@@ -1,5 +1,4 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
@@ -7,76 +6,12 @@
 #include "qca956x.dtsi"
 
 / {
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-	};
-
 	aliases {
-		led-boot = &led_power;
-		led-failsafe = &led_power;
-		led-running = &led_power;
-		led-upgrade = &led_power;
 		label-mac-device = &eth0;
 	};
 
-	leds {
-		compatible = "gpio-leds";
-
-		led_power: power {
-			label = "tp-link:green:power";
-			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
-			default-state = "on";
-		};
-
-		wlan2g {
-			label = "tp-link:green:wlan2g";
-			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "phy1tpt";
-		};
-
-		wlan5g {
-			label = "tp-link:green:wlan5g";
-			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "phy0tpt";
-		};
-
-		lan {
-			label = "tp-link:green:lan";
-			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
-		};
-
-		wan {
-			label = "tp-link:green:wan";
-			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
-		};
-
-		wan_fail {
-			label = "tp-link:amber:wan";
-			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
-		};
-
-		wps {
-			label = "tp-link:green:wps";
-			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "Reset button";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-
-		wps {
-			label = "WPS button";
-			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
 	};
 };
 
@@ -92,54 +27,6 @@
 	status = "okay";
 };
 
-&spi {
-	status = "okay";
-
-	num-cs = <1>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "u-boot";
-				reg = <0x000000 0x020000>;
-				read-only;
-			};
-
-			mac: partition@20000 {
-				label = "mac";
-				reg = <0x020000 0x010000>;
-				read-only;
-			};
-
-			partition@30000 {
-				compatible = "denx,uimage";
-				label = "firmware";
-				reg = <0x030000 0x7a0000>;
-			};
-
-			partition@7d0000 {
-				label = "tplink";
-				reg = <0x7d0000 0x020000>;
-				read-only;
-			};
-
-			art: partition@7f0000 {
-				label = "art";
-				reg = <0x7f0000 0x010000>;
-				read-only;
-			};
-		};
-	};
-};
-
 &mdio0 {
 	status = "okay";
 
@@ -161,8 +48,9 @@
 	status = "okay";
 
 	phy-mode = "sgmii";
-	mtd-mac-address = <&mac 0x8>;
 	phy-handle = <&phy0>;
+
+	mtd-mac-address = <&mac 0x8>;
 };
 
 &wmac {
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index c914090cf9..5561677ec3 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -146,7 +146,8 @@ tplink,tl-wr1043n-v5)
 	ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x04"
 	ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x02"
 	;;
-tplink,archer-c6-v2)
+tplink,archer-c6-v2|\
+tplink,archer-c6-v2-us)
 	ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C"
 	ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02"
 	;;
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 7090825c2f..e811f85f0e 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -207,6 +207,7 @@ ath79_setup_interfaces()
 		;;
 	tplink,archer-a7-v5|\
 	tplink,archer-c6-v2|\
+	tplink,archer-c6-v2-us|\
 	tplink,archer-c7-v4|\
 	tplink,archer-c7-v5|\
 	tplink,tl-wdr3600-v1|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 97233fa0e4..062caf6ad5 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -146,7 +146,8 @@ case "$FIRMWARE" in
 	tplink,archer-c59-v2|\
 	tplink,archer-c60-v1|\
 	tplink,archer-c60-v2|\
-	tplink,archer-c6-v2)
+	tplink,archer-c6-v2|\
+	tplink,archer-c6-v2-us)
 		caldata_extract "art" 0x5000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
 		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index ae956eb98e..f5e1a90418 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -88,12 +88,26 @@ define Device/tplink_archer-c6-v2
   ATH_SOC := qca9563
   IMAGE_SIZE := 7808k
   DEVICE_MODEL := Archer C6
-  DEVICE_VARIANT := v2
+  DEVICE_VARIANT := v2 (EU/RU/JP)
   TPLINK_BOARD_ID := ARCHER-C6-V2
   DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
 endef
 TARGET_DEVICES += tplink_archer-c6-v2
 
+define Device/tplink_archer-c6-v2-us
+  $(Device/tplink-safeloader-uimage)
+  ATH_SOC := qca9563
+  IMAGE_SIZE := 15872k
+  DEVICE_MODEL := Archer C6
+  DEVICE_VARIANT := v2 (US)
+  DEVICE_ALT0_VENDOR := TP-Link
+  DEVICE_ALT0_MODEL := Archer A6
+  DEVICE_ALT0_VARIANT := v2 (US/TW)
+  TPLINK_BOARD_ID := ARCHER-C6-V2-US
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+endef
+TARGET_DEVICES += tplink_archer-c6-v2-us
+
 define Device/tplink_archer-c60-v1
   $(Device/tplink-safeloader-uimage)
   ATH_SOC := qca9561
-- 
cgit v1.2.3