From 35f6d795134e9b089c4e763a7f58cba7d4e15e42 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Sat, 18 Feb 2023 02:06:54 +0100 Subject: mpc85xx: add support for Watchguard Firebox T10 Hardware -------- SoC: Freescale P1010 RAM: 512MB FLASH: 1 MB SPI-NOR 512 MB NAND ETH: 3x Gigabite Ethernet (Atheros AR8033) SERIAL: Cisco RJ-45 (115200 8N1) RTC: Battery-Backed RTC (I2C) Installation ------------ 1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI programmer. The SHA1 hash for the U-Boot password is currently unknown. A tool for patching U-Boot is available at https://github.com/blocktrron/t10-uboot-patcher/ You can also patch the unknown password yourself. The SHA1 hash is E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA 2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears. The patched password is '1234' (without quotation marks) 3. Download the OpenWrt initramfs image. Copy it to a TFTP server reachable at 10.0.1.13/24 and rename it to uImage. 4. Connect the TFTP server to ethernet port 0 of the Watchguard T10. 5. Download and boot the initramfs image by entering "tftpboot; bootm;" in U-Boot. 6. After OpenWrt booted, create a UBI volume on the old data partition. The "ubi" mtd partition should be mtd7, check this using $ cat /proc/mtd Create a UBI partition by executing $ ubiformat /dev/mtd7 -y 7. Increase the loadable kernel-size of U-Boot by executing $ fw_setenv SysAKernSize 800000 8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using scp. Install the image by using sysupgrade: $ sysupgrade -n Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might have to change the ethernet-port. 9. OpenWrt should now boot from the internal NAND. Enjoy. Signed-off-by: David Bauer --- ...08-powerpc-85xx-firebox-t10-support.patch.patch | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 target/linux/mpc85xx/patches-5.10/108-powerpc-85xx-firebox-t10-support.patch.patch (limited to 'target/linux/mpc85xx/patches-5.10') diff --git a/target/linux/mpc85xx/patches-5.10/108-powerpc-85xx-firebox-t10-support.patch.patch b/target/linux/mpc85xx/patches-5.10/108-powerpc-85xx-firebox-t10-support.patch.patch new file mode 100644 index 0000000000..b074113eaa --- /dev/null +++ b/target/linux/mpc85xx/patches-5.10/108-powerpc-85xx-firebox-t10-support.patch.patch @@ -0,0 +1,29 @@ +--- a/arch/powerpc/platforms/85xx/Kconfig ++++ b/arch/powerpc/platforms/85xx/Kconfig +@@ -92,6 +92,16 @@ config WS_AP3825I + This board is a Concurrent Dual-Band wireless access point with a + Freescale P1020 SoC. + ++config FIREBOX_T10 ++ bool "Watchguard Firebox T10" ++ select DEFAULT_UIMAGE ++ select ARCH_REQUIRE_GPIOLIB ++ select GPIO_MPC8XXX ++ help ++ This option enables support for the Watchguard Firebox T10 board. ++ This board is a VPN Gateway-Router with a ++ Freescale P1010 SoC. ++ + config MPC8540_ADS + bool "Freescale MPC8540 ADS" + select DEFAULT_UIMAGE +--- a/arch/powerpc/platforms/85xx/Makefile ++++ b/arch/powerpc/platforms/85xx/Makefile +@@ -28,6 +28,7 @@ obj-$(CONFIG_PANDA) += panda.o + obj-$(CONFIG_TWR_P102x) += twr_p102x.o + obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o + obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o ++obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o + obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o + obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o + obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o -- cgit v1.2.3