From 1cb406d019dc84497a8405c470f0b0394d5ff64a Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Tue, 14 Mar 2017 17:04:28 +0100 Subject: ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see and ) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter Signed-off-by: John Crispin --- target/linux/ipq806x/base-files/etc/board.d/01_leds | 5 +++++ target/linux/ipq806x/base-files/etc/board.d/02_network | 5 +++++ .../base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 15 +++++++++++++++ target/linux/ipq806x/base-files/lib/ipq806x.sh | 3 +++ target/linux/ipq806x/base-files/lib/upgrade/platform.sh | 3 +++ 5 files changed, 31 insertions(+) (limited to 'target/linux/ipq806x/base-files') diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 977b3b104e..1371767268 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -26,6 +26,11 @@ r7800) ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0" ucidef_set_led_ide "esata" "eSATA" "${board}:white:esata" ;; +fritz4040) + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" "phy1tpt" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" + ucidef_set_led_switch "lan" "LAN" "${board}:green:lan" "switch0" "0x1e" + ;; nbg6817) ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:amber:wifi2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5g" "phy0tpt" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 52bb1629f7..36e0fb3a0e 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -36,6 +36,11 @@ ea8500) ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; +fritz4040) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" + ;; nbg6817) hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 72c3ae88c2..652621247f 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -46,6 +46,21 @@ board=$(ipq806x_board_name) case "$FIRMWARE" in +"ath10k/pre-cal-ahb-a000000.wifi.bin") + case "$board" in + fritz4040) + /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") + ;; + esac + ;; +"ath10k/pre-cal-ahb-a800000.wifi.bin") + case "$board" in + fritz4040) + /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") + ;; + esac + ;; + "ath10k/cal-pci-0000:01:00.0.bin") case $board in c2600) diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index a8b909ac04..348a3a8951 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -17,6 +17,9 @@ ipq806x_board_detect() { *"AP148") name="ap148" ;; + *"4040") + name="fritz4040" + ;; *"C2600") name="c2600" ;; diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index c3741f9ff2..89702850fc 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -42,6 +42,9 @@ platform_do_upgrade() { MTD_CONFIG_ARGS="-s 0x200000" default_do_upgrade "$ARGV" ;; + *) + default_do_upgrade "$ARGV" + ;; esac } -- cgit v1.2.3