From ea5bb6bbfee06f44f714aff40c8929505face221 Mon Sep 17 00:00:00 2001 From: Marek Lindner Date: Sun, 25 Nov 2018 21:46:54 +0800 Subject: ipq40xx: add support for Plasma Cloud PA1200 Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann --- target/linux/ipq40xx/image/Makefile | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'target/linux/ipq40xx/image') diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index b3f2d1f755..b0fde22813 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -648,6 +648,22 @@ define Device/openmesh_a62 endef TARGET_DEVICES += openmesh_a62 +define Device/plasmacloud_pa1200 + $(call Device/FitImageLzma) + DEVICE_VENDOR := Plasma Cloud + DEVICE_MODEL := PA1200 + SOC := qcom-ipq4018 + DEVICE_DTS_CONFIG := config@pc.pa1200 + BLOCKSIZE := 64k + KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) + IMAGE_SIZE := 15616k + IMAGES += factory.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200 + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := uboot-envtools ipq-wifi-plasmacloud-pa1200 +endef +TARGET_DEVICES += plasmacloud_pa1200 + define Device/qcom_ap-dk01.1-c1 DEVICE_VENDOR := Qualcomm Atheros DEVICE_MODEL := AP-DK01.1 -- cgit v1.2.3