From 4871fd2616acb03fefe69b068955dba36eb00770 Mon Sep 17 00:00:00 2001 From: Marek Lindner Date: Fri, 14 Dec 2018 23:46:53 +0800 Subject: ipq40xx: add support for Plasma Cloud PA2200 Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann --- target/linux/ipq40xx/image/Makefile | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'target/linux/ipq40xx/image') diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index b0fde22813..86bf5a2ccb 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -664,6 +664,22 @@ define Device/plasmacloud_pa1200 endef TARGET_DEVICES += plasmacloud_pa1200 +define Device/plasmacloud_pa2200 + $(call Device/FitImageLzma) + DEVICE_VENDOR := Plasma Cloud + DEVICE_MODEL := PA2200 + SOC := qcom-ipq4019 + DEVICE_DTS_CONFIG := config@pc.pa2200 + BLOCKSIZE := 64k + KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) + IMAGE_SIZE := 15552k + IMAGES += factory.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200 + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-plasmacloud-pa2200 uboot-envtools +endef +TARGET_DEVICES += plasmacloud_pa2200 + define Device/qcom_ap-dk01.1-c1 DEVICE_VENDOR := Qualcomm Atheros DEVICE_MODEL := AP-DK01.1 -- cgit v1.2.3