From f8cd14921d9ae957a092378317bc11ededdeb0ef Mon Sep 17 00:00:00 2001 From: Jonas Gorski Date: Fri, 6 Sep 2013 19:01:17 +0000 Subject: brcm63xx: drop linux 3.9 support It is EOL since quite a while, so no need to keep it around. Signed-off-by: Jonas Gorski SVN-Revision: 37911 --- target/linux/brcm63xx/config-3.9 | 189 --- ...-properly-prepare-clocks-before-enabling-.patch | 61 - ...bcm63xx-remove-duplicated-mode-bits-check.patch | 27 - ...spi-bcm63xx-remove-unneeded-debug-message.patch | 26 - ...-remove-unused-variable-bs-from-bcm63xx_s.patch | 26 - ...63xx-check-spi-bits_per_word-in-spi_setup.patch | 29 - ...m63xx-simplify-bcm63xx_spi_check_transfer.patch | 30 - ...3xx-remove-spi-chip-select-validity-check.patch | 28 - ...bcm63xx-inline-bcm63xx_spi_check_transfer.patch | 48 - ...-inline-hz-usage-in-bcm63xx_spi_setup_tra.patch | 43 - ...014-spi-bcm63xx-use-devm_ioremap_resource.patch | 36 - ...xx-remove-unused-speed_hz-member-variable.patch | 67 - ...XX-merge-bcm63xx_clk.h-into-bcm63xx-clk.c.patch | 57 - ...xx_enet-use-managed-io-memory-allocations.patch | 118 -- ...m63xx_enet-use-managed-memory-allocations.patch | 42 - ...t-properly-prepare-unprepare-clocks-befor.patch | 62 - ...X-remove-duplicate-spi-register-definitio.patch | 166 --- .../023-MIPS-BCM63XX-fix-revision-ID-width.patch | 68 - .../024-MIPS-BCM63XX-rework-chip-detection.patch | 133 -- ...25-MIPS-BCM63XX-add-basic-BCM6362-support.patch | 575 -------- ...BCM63XX-enable-SPI-controller-for-BCM6362.patch | 57 - .../027-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch | 56 - ...S-BCM63XX-add-flash-detection-for-BCM6362.patch | 38 - ...X-add-missing-clocks-for-BCM6328-and-BCM6.patch | 91 -- ...3xxpart-use-size-macro-for-CFE-block-size.patch | 29 - ...1-MIPS-BCM63XX-export-PSI-size-from-nvram.patch | 58 - ...32-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch | 42 - .../033-MIPS-BCM63XX-Handle-SW-IRQs-0-1.patch | 28 - ...X-select-BMIPS4350-and-default-to-2-CPUs-.patch | 27 - .../035-MIPS-BCM63XX-select-BOOT_RAW.patch | 30 - ...M63XX-add-support-for-BCM3368-Cable-Modem.patch | 629 -------- ...3XX-recognize-Cable-Modem-firmware-format.patch | 101 -- ...X-provide-a-MAC-address-for-BCM3368-chips.patch | 46 - ...X-let-board-specify-an-external-GPIO-to-r.patch | 49 - ...M63XX-add-support-for-the-Netgear-CVG834G.patch | 70 - ...MIPS-BCM63XX-remove-bogus-Kconfig-selects.patch | 47 - ...support-booting-from-physical-CPU-other-t.patch | 89 -- ...43-MIPS-BCM63XX-Add-SMP-support-to-prom.c.patch | 82 -- ...X-Enable-second-core-SMP-on-BCM6328-if-av.patch | 55 - ...t-implement-reset-autoneg-ethtool-callbac.patch | 44 - ..._enet-split-DMA-channel-register-accesses.patch | 346 ----- ...t-add-support-for-Broadcom-BCM63xx-integr.patch | 1505 -------------------- ...net-add-support-Broadcom-BCM6345-Ethernet.patch | 838 ----------- ...-MIPS-bmips-fix-compilation-for-BMIPS5000.patch | 67 - ...ow-asm-cpu.h-to-be-included-from-assembly.patch | 31 - ...add-macros-for-testing-the-current-bmips-.patch | 36 - ...change-compile-time-checks-to-runtime-che.patch | 482 ------- ...S-bmips-merge-CPU-options-into-one-option.patch | 126 -- ...X-let-the-individual-SoCs-select-the-appr.patch | 72 - ...add-a-helper-function-for-registering-smp.patch | 42 - ...IPS-BCM63XX-always-register-bmips-smp-ops.patch | 26 - ...3XX-change-the-guard-to-a-BMIPS4350-check.patch | 21 - ...-MIPS-BCM63XX-disable-SMP-also-on-BCM3368.patch | 36 - ...S-BCM63XX-add-USB-host-clock-enable-delay.patch | 28 - ...X-add-USB-device-clock-enable-delay-to-cl.patch | 41 - ...X-move-code-touching-the-USB-private-regi.patch | 151 -- ...X-add-OHCI-EHCI-configuration-bits-to-com.patch | 169 --- ...X-introduce-BCM63XX_OHCI-configuration-sy.patch | 62 - ...X-add-support-for-the-on-chip-OHCI-contro.patch | 138 -- ...X-register-OHCI-controller-if-board-enabl.patch | 36 - ...X-introduce-BCM63XX_EHCI-configuration-sy.patch | 82 -- ...X-add-support-for-the-on-chip-EHCI-contro.patch | 136 -- ...X-register-EHCI-controller-if-board-enabl.patch | 36 - ...X-EHCI-controller-does-not-support-overcu.patch | 24 - ...llow-specifying-the-parsers-for-SPI-flash.patch | 38 - ...-m25p80-use-parsers-if-provided-in-flash-.patch | 23 - ...CES-m25p80-add-support-for-limiting-reads.patch | 92 -- .../brcm63xx/patches-3.9/300-reset_buttons.patch | 116 -- .../linux/brcm63xx/patches-3.9/301-led_count.patch | 41 - .../302-extended-platform-devices.patch | 25 - .../brcm63xx/patches-3.9/303-spi-board-info.patch | 33 - .../brcm63xx/patches-3.9/304-boardid_fixup.patch | 62 - .../306-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch | 48 - ...PS-BCM63XX-add-HSSPI-register-definitions.patch | 211 --- .../patches-3.9/308-board_leds_naming.patch | 267 ---- .../brcm63xx/patches-3.9/309-cfe_version_mod.patch | 27 - ...X-rename-__dispatch_internal-to-__dispatc.patch | 51 - ...X-replace-irq-dispatch-code-with-a-generi.patch | 167 --- ...M63XX-append-cpu-number-to-irq_-stat-mask.patch | 279 ---- ...X-populate-irq_-stat-mask-_addr-for-secon.patch | 186 --- ...X-use-a-helper-for-getting-the-right-regi.patch | 80 -- ...3XX-add-cpu-argument-to-dispatch-internal.patch | 73 - ...IPS-BCM63XX-protect-irq-register-accesses.patch | 158 -- ...BCM63XX-wire-up-the-second-CPU-s-irq-line.patch | 100 -- ...63XX-use-irq_desc-as-argument-for-un-mask.patch | 98 -- ...S-BCM63XX-allow-setting-affinity-for-IPIC.patch | 124 -- .../patches-3.9/323-cfe_simplify_detection.patch | 20 - .../324-bcm63xxpart_use_cfedetection.patch | 51 - .../patches-3.9/400-bcm963xx_flashmap.patch | 65 - .../401-bcm963xx_real_rootfs_length.patch | 27 - .../402_bcm63xx_enet_vlan_incoming_fixed.patch | 11 - .../403-6358-enet1-external-mii-clk.patch | 22 - ..._enet-move-phy_-dis-connect-into-probe-re.patch | 169 --- ...enet-enable-rgmii-clock-on-external-ports.patch | 53 - ...X-add-HS-SPI-platform-device-and-register.patch | 134 -- .../410-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch | 481 ------- ...IPS-BCM63XX-Register-SPI-flash-if-present.patch | 104 -- .../412-MTD-physmap-allow-passing-pp_data.patch | 41 - ...-allow-providing-fixup-data-in-board-data.patch | 81 -- .../414-MTD-m25p80-allow-passing-pp_data.patch | 40 - ...X-store-the-flash-type-in-global-variable.patch | 119 -- ...416-BCM63XX-add-a-fixup-for-ath9k-devices.patch | 227 --- ...cm63xxpart-allow-passing-a-caldata-offset.patch | 120 -- ...8-MIPS-BCM63XX-pass-caldata-info-to-flash.patch | 82 -- .../420-BCM63XX-add-endian-check-for-ath9k.patch | 51 - .../421-BCM63XX-add-led-pin-for-ath9k.patch | 49 - ...22-BCM63XX-add-a-fixup-for-rt2x00-devices.patch | 205 --- .../423-bcm63xx_enet_add_b53_support.patch | 169 --- .../brcm63xx/patches-3.9/500-board-D4PW.patch | 67 - .../linux/brcm63xx/patches-3.9/501-board-NB4.patch | 650 --------- .../patches-3.9/502-board-96338W2_E7T.patch | 51 - .../brcm63xx/patches-3.9/503-board-CPVA642.patch | 109 -- .../patches-3.9/504-board_dsl_274xb_rev_c.patch | 72 - .../brcm63xx/patches-3.9/505-board_spw500v.patch | 78 - .../patches-3.9/506-board_gw6200_gw6000.patch | 124 -- .../brcm63xx/patches-3.9/507-board-MAGIC.patch | 89 -- .../brcm63xx/patches-3.9/508-board_hw553.patch | 93 -- .../patches-3.9/509-board_rta1320_16m.patch | 56 - .../brcm63xx/patches-3.9/510-board_spw303v.patch | 83 -- .../brcm63xx/patches-3.9/511-board_V2500V.patch | 123 -- .../brcm63xx/patches-3.9/512-board_BTV2110.patch | 75 - .../brcm63xx/patches-3.9/513-board_livebox.patch | 390 ----- .../patches-3.9/514-board_ct536_ct5621.patch | 62 - .../patches-3.9/515-board_DWV-S0_fixes.patch | 19 - .../patches-3.9/516-board_96348A-122.patch | 80 -- .../patches-3.9/517-RTA1205W_16_uart_fixes.patch | 10 - .../patches-3.9/519_board_CPVA502plus.patch | 57 - ...0-bcm63xx-add-support-for-96368MVWG-board.patch | 128 -- ...-bcm63xx-add-support-for-96368MVNgr-board.patch | 92 -- ...IPS-BCM63XX-add-96328avng-reference-board.patch | 67 - ...IPS-BCM63XX-add-963281TAN-reference-board.patch | 96 -- .../patches-3.9/524-board_dsl_274xb_rev_f.patch | 132 -- .../brcm63xx/patches-3.9/525-board_96348w3.patch | 70 - .../brcm63xx/patches-3.9/526-board_CT6373-1.patch | 138 -- .../patches-3.9/527-board_dva-g3810bn-tl-1.patch | 84 -- .../linux/brcm63xx/patches-3.9/528-board_nb6.patch | 146 -- .../brcm63xx/patches-3.9/529-board_fast2604.patch | 68 - .../patches-3.9/530-board_963281T_TEF.patch | 136 -- .../patches-3.9/531-board_96328A-1441N1.patch | 89 -- .../patches-3.9/532-board_96328a-1241N.patch | 83 -- .../brcm63xx/patches-3.9/533-board_rta770bw.patch | 66 - .../brcm63xx/patches-3.9/534-board_hw556.patch | 561 -------- .../brcm63xx/patches-3.9/535-board_rta770w.patch | 71 - .../patches-3.9/550-alice_gate2_leds.patch | 102 -- .../brcm63xx/patches-3.9/551-96348gw_a_leds.patch | 22 - .../552-board_96348gw-10_reset_button.patch | 20 - .../patches-3.9/553-boards_probe_switch.patch | 119 -- .../patches-3.9/554-board_DWVS0_leds_buttons.patch | 97 -- .../brcm63xx/patches-3.9/800-wl_exports.patch | 34 - .../801-ssb_export_fallback_sprom.patch | 27 - .../802-rtl8367r_fix_RGMII_support.patch | 30 - 151 files changed, 17416 deletions(-) delete mode 100644 target/linux/brcm63xx/config-3.9 delete mode 100644 target/linux/brcm63xx/patches-3.9/005-spi-bcm63xx-properly-prepare-clocks-before-enabling-.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/006-spi-bcm63xx-remove-duplicated-mode-bits-check.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/007-spi-bcm63xx-remove-unneeded-debug-message.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/008-spi-bcm63xx-remove-unused-variable-bs-from-bcm63xx_s.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/009-spi-bcm63xx-check-spi-bits_per_word-in-spi_setup.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/010-spi-bcm63xx-simplify-bcm63xx_spi_check_transfer.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/011-spi-bcm63xx-remove-spi-chip-select-validity-check.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/012-spi-bcm63xx-inline-bcm63xx_spi_check_transfer.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/013-spi-bcm63xx-inline-hz-usage-in-bcm63xx_spi_setup_tra.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/014-spi-bcm63xx-use-devm_ioremap_resource.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/015-spi-bcm63xx-remove-unused-speed_hz-member-variable.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/018-MIPS-BCM63XX-merge-bcm63xx_clk.h-into-bcm63xx-clk.c.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/019-bcm63xx_enet-use-managed-io-memory-allocations.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/020-bcm63xx_enet-use-managed-memory-allocations.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/021-bcm63xx_enet-properly-prepare-unprepare-clocks-befor.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/022-MIPS-BCM63XX-remove-duplicate-spi-register-definitio.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/023-MIPS-BCM63XX-fix-revision-ID-width.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/024-MIPS-BCM63XX-rework-chip-detection.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/025-MIPS-BCM63XX-add-basic-BCM6362-support.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/026-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/027-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/028-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/029-MIPS-BCM63XX-add-missing-clocks-for-BCM6328-and-BCM6.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/030-MTD-bcm63xxpart-use-size-macro-for-CFE-block-size.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/031-MIPS-BCM63XX-export-PSI-size-from-nvram.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/032-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/033-MIPS-BCM63XX-Handle-SW-IRQs-0-1.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/034-MIPS-BCM63XX-select-BMIPS4350-and-default-to-2-CPUs-.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/035-MIPS-BCM63XX-select-BOOT_RAW.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/036-MIPS-BCM63XX-add-support-for-BCM3368-Cable-Modem.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/037-MIPS-BCM63XX-recognize-Cable-Modem-firmware-format.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/038-MIPS-BCM63XX-provide-a-MAC-address-for-BCM3368-chips.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/039-MIPS-BCM63XX-let-board-specify-an-external-GPIO-to-r.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/040-MIPS-BCM63XX-add-support-for-the-Netgear-CVG834G.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/041-MIPS-BCM63XX-remove-bogus-Kconfig-selects.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/042-MIPS-BMIPS-support-booting-from-physical-CPU-other-t.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/043-MIPS-BCM63XX-Add-SMP-support-to-prom.c.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/044-MIPS-BCM63XX-Enable-second-core-SMP-on-BCM6328-if-av.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/045-bcm63xx_enet-implement-reset-autoneg-ethtool-callbac.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/046-bcm63xx_enet-split-DMA-channel-register-accesses.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/047-bcm63xx_enet-add-support-for-Broadcom-BCM63xx-integr.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/048-bcm63xx_enet-add-support-Broadcom-BCM6345-Ethernet.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/100-MIPS-bmips-fix-compilation-for-BMIPS5000.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/101-MIPS-allow-asm-cpu.h-to-be-included-from-assembly.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/102-MIPS-bmips-add-macros-for-testing-the-current-bmips-.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/103-MIPS-bmips-change-compile-time-checks-to-runtime-che.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/104-MIPS-bmips-merge-CPU-options-into-one-option.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/105-MIPS-BCM63XX-let-the-individual-SoCs-select-the-appr.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/106-MIPS-bmips-add-a-helper-function-for-registering-smp.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/107-MIPS-BCM63XX-always-register-bmips-smp-ops.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/108-MIPS-BCM63XX-change-the-guard-to-a-BMIPS4350-check.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/109-MIPS-BCM63XX-disable-SMP-also-on-BCM3368.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/110-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/111-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/112-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/113-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/114-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/115-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/116-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/117-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/118-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/119-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/120-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/300-reset_buttons.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/301-led_count.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/302-extended-platform-devices.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/303-spi-board-info.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/304-boardid_fixup.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/306-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/307-MIPS-BCM63XX-add-HSSPI-register-definitions.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/308-board_leds_naming.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/309-cfe_version_mod.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/313-MIPS-BCM63XX-rename-__dispatch_internal-to-__dispatc.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/314-MIPS-BCM63XX-replace-irq-dispatch-code-with-a-generi.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/315-MIPS-BCM63XX-append-cpu-number-to-irq_-stat-mask.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/316-MIPS-BCM63XX-populate-irq_-stat-mask-_addr-for-secon.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/317-MIPS-BCM63XX-use-a-helper-for-getting-the-right-regi.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/318-MIPS-BCM63XX-add-cpu-argument-to-dispatch-internal.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/319-MIPS-BCM63XX-protect-irq-register-accesses.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/320-MIPS-BCM63XX-wire-up-the-second-CPU-s-irq-line.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/321-MIPS-BCM63XX-use-irq_desc-as-argument-for-un-mask.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/322-MIPS-BCM63XX-allow-setting-affinity-for-IPIC.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/323-cfe_simplify_detection.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/324-bcm63xxpart_use_cfedetection.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/400-bcm963xx_flashmap.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/401-bcm963xx_real_rootfs_length.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/402_bcm63xx_enet_vlan_incoming_fixed.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/403-6358-enet1-external-mii-clk.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/409-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/410-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/412-MTD-physmap-allow-passing-pp_data.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/414-MTD-m25p80-allow-passing-pp_data.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/415-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/420-BCM63XX-add-endian-check-for-ath9k.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/421-BCM63XX-add-led-pin-for-ath9k.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/423-bcm63xx_enet_add_b53_support.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/500-board-D4PW.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/501-board-NB4.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/502-board-96338W2_E7T.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/503-board-CPVA642.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/504-board_dsl_274xb_rev_c.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/505-board_spw500v.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/506-board_gw6200_gw6000.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/507-board-MAGIC.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/508-board_hw553.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/509-board_rta1320_16m.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/510-board_spw303v.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/512-board_BTV2110.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/513-board_livebox.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/514-board_ct536_ct5621.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/515-board_DWV-S0_fixes.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/516-board_96348A-122.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/517-RTA1205W_16_uart_fixes.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/519_board_CPVA502plus.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/520-bcm63xx-add-support-for-96368MVWG-board.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/521-bcm63xx-add-support-for-96368MVNgr-board.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/522-MIPS-BCM63XX-add-96328avng-reference-board.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/524-board_dsl_274xb_rev_f.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/525-board_96348w3.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/526-board_CT6373-1.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/527-board_dva-g3810bn-tl-1.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/528-board_nb6.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/529-board_fast2604.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/530-board_963281T_TEF.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/531-board_96328A-1441N1.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/532-board_96328a-1241N.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/533-board_rta770bw.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/534-board_hw556.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/535-board_rta770w.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/550-alice_gate2_leds.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/551-96348gw_a_leds.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/552-board_96348gw-10_reset_button.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/553-boards_probe_switch.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/554-board_DWVS0_leds_buttons.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/800-wl_exports.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/801-ssb_export_fallback_sprom.patch delete mode 100644 target/linux/brcm63xx/patches-3.9/802-rtl8367r_fix_RGMII_support.patch (limited to 'target/linux/brcm63xx') diff --git a/target/linux/brcm63xx/config-3.9 b/target/linux/brcm63xx/config-3.9 deleted file mode 100644 index 6d87c185d1..0000000000 --- a/target/linux/brcm63xx/config-3.9 +++ /dev/null @@ -1,189 +0,0 @@ -CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y -CONFIG_ARCH_DISCARD_MEMBLOCK=y -CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y -CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_REQUIRE_GPIOLIB=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y -CONFIG_AUDIT=y -CONFIG_AUDIT_GENERIC=y -CONFIG_B53=y -CONFIG_B53_MMAP_DRIVER=y -CONFIG_B53_PHY_DRIVER=y -CONFIG_B53_PHY_FIXUP=y -CONFIG_B53_SPI_DRIVER=y -CONFIG_BCM63XX=y -CONFIG_BCM63XX_CPU_3368=y -CONFIG_BCM63XX_CPU_6328=y -CONFIG_BCM63XX_CPU_6338=y -CONFIG_BCM63XX_CPU_6345=y -CONFIG_BCM63XX_CPU_6348=y -CONFIG_BCM63XX_CPU_6358=y -CONFIG_BCM63XX_CPU_6362=y -CONFIG_BCM63XX_CPU_6368=y -CONFIG_BCM63XX_EHCI=y -CONFIG_BCM63XX_ENET=y -CONFIG_BCM63XX_OHCI=y -CONFIG_BCM63XX_PHY=y -CONFIG_BCM63XX_WDT=y -CONFIG_BOARD_BCM963XX=y -# CONFIG_BOARD_LIVEBOX is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_CEVT_R4K=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200" -CONFIG_CMDLINE_BOOL=y -# CONFIG_CMDLINE_OVERRIDE is not set -CONFIG_CPU_BIG_ENDIAN=y -# CONFIG_CPU_BMIPS is not set -CONFIG_CPU_GENERIC_DUMP_TLB=y -CONFIG_CPU_HAS_PREFETCH=y -CONFIG_CPU_HAS_SYNC=y -CONFIG_CPU_MIPS32=y -CONFIG_CPU_MIPS32_R1=y -CONFIG_CPU_MIPSR1=y -CONFIG_CPU_R4K_CACHE_TLB=y -CONFIG_CPU_R4K_FPU=y -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -CONFIG_CSRC_R4K=y -CONFIG_DECOMPRESS_LZMA=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_EARLY_PRINTK=y -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_GENERIC_ATOMIC64=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_GENERIC_GPIO=y -CONFIG_GENERIC_IO=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GPIOLIB=y -CONFIG_GPIO_74X164=y -CONFIG_GPIO_DEVRES=y -CONFIG_GPIO_SYSFS=y -# CONFIG_HAMRADIO is not set -CONFIG_HARDWARE_WATCHPOINTS=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set -CONFIG_HAVE_ARCH_JUMP_LABEL=y -CONFIG_HAVE_ARCH_KGDB=y -# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set -CONFIG_HAVE_CLK=y -CONFIG_HAVE_C_RECORDMCOUNT=y -CONFIG_HAVE_DEBUG_KMEMLEAK=y -CONFIG_HAVE_DMA_API_DEBUG=y -CONFIG_HAVE_DMA_ATTRS=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y -CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_GENERIC_HARDIRQS=y -CONFIG_HAVE_IDE=y -CONFIG_HAVE_MEMBLOCK=y -CONFIG_HAVE_MEMBLOCK_NODE_MAP=y -CONFIG_HAVE_MOD_ARCH_SPECIFIC=y -CONFIG_HAVE_NET_DSA=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HW_HAS_PCI=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_BCM63XX=y -CONFIG_HZ=250 -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -CONFIG_IMAGE_CMDLINE_HACK=y -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -CONFIG_IRQ_CPU=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -CONFIG_KEXEC=y -CONFIG_LEDS_GPIO=y -CONFIG_M25PXX_USE_FAST_READ=y -CONFIG_MDIO_BOARDINFO=y -CONFIG_MIPS=y -# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set -CONFIG_MIPS_L1_CACHE_SHIFT=5 -# CONFIG_MIPS_MACHINE is not set -CONFIG_MIPS_MT_DISABLED=y -CONFIG_MODULES_USE_ELF_REL=y -CONFIG_MODULE_FORCE_LOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MTD_BCM63XX_PARTS=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -CONFIG_MTD_CFI_BE_BYTE_SWAP=y -# CONFIG_MTD_CFI_GEOMETRY is not set -# CONFIG_MTD_CFI_NOSWAP is not set -CONFIG_MTD_CFI_STAA=y -CONFIG_MTD_CMDLINE_PARTS=y -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -CONFIG_MTD_JEDECPROBE=y -CONFIG_MTD_M25P80=y -CONFIG_MTD_PHYSMAP=y -CONFIG_MTD_REDBOOT_PARTS=y -CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_PER_CPU_KM=y -CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y -CONFIG_NR_CPUS_DEFAULT_2=y -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_PCI=y -# CONFIG_PCIEAER is not set -CONFIG_PCIEPORTBUS=y -CONFIG_PCI_DOMAINS=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PHYLIB=y -CONFIG_POSIX_MQUEUE=y -CONFIG_POSIX_MQUEUE_SYSCTL=y -# CONFIG_PREEMPT_RCU is not set -# CONFIG_RCU_STALL_COMMON is not set -CONFIG_RELAY=y -CONFIG_RTL8366_SMI=y -CONFIG_RTL8367_PHY=y -# CONFIG_SCSI_DMA is not set -# CONFIG_SERIAL_8250 is not set -CONFIG_SERIAL_BCM63XX=y -CONFIG_SERIAL_BCM63XX_CONSOLE=y -CONFIG_SPI=y -CONFIG_SPI_BCM63XX=y -CONFIG_SPI_BCM63XX_HSSPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_GPIO=y -CONFIG_SPI_MASTER=y -CONFIG_SQUASHFS_EMBEDDED=y -CONFIG_SSB=y -CONFIG_SSB_B43_PCI_BRIDGE=y -CONFIG_SSB_BLOCKIO=y -# CONFIG_SSB_DRIVER_MIPS is not set -CONFIG_SSB_DRIVER_PCICORE=y -CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y -CONFIG_SSB_PCIHOST=y -CONFIG_SSB_PCIHOST_POSSIBLE=y -CONFIG_SSB_SPROM=y -CONFIG_SWAP_IO_SPACE=y -CONFIG_SWCONFIG=y -CONFIG_SYS_HAS_CPU_BMIPS=y -CONFIG_SYS_HAS_CPU_BMIPS3300=y -CONFIG_SYS_HAS_CPU_BMIPS4350=y -CONFIG_SYS_HAS_CPU_MIPS32_R1=y -CONFIG_SYS_HAS_EARLY_PRINTK=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_UIDGID_CONVERTED=y -CONFIG_USB_ARCH_HAS_XHCI=y -# CONFIG_USB_HCD_SSB is not set -CONFIG_USB_SUPPORT=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_WATCHDOG_NOWAYOUT=y -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/brcm63xx/patches-3.9/005-spi-bcm63xx-properly-prepare-clocks-before-enabling-.patch b/target/linux/brcm63xx/patches-3.9/005-spi-bcm63xx-properly-prepare-clocks-before-enabling-.patch deleted file mode 100644 index b75a57c0fd..0000000000 --- a/target/linux/brcm63xx/patches-3.9/005-spi-bcm63xx-properly-prepare-clocks-before-enabling-.patch +++ /dev/null @@ -1,61 +0,0 @@ -From e504d3ed9b35f43e61cf239b103667d87cd7bf3c Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 10 Sep 2012 01:26:55 +0200 -Subject: [PATCH 03/12] spi/bcm63xx: properly prepare clocks before enabling - them - -Use proper clk_prepare/unprepare calls in preparation for switching -to the generic clock framework. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 10 +++++----- - 1 file changed, 5 insertions(+), 5 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -493,7 +493,7 @@ static int bcm63xx_spi_probe(struct plat - } - - /* Initialize hardware */ -- clk_enable(bs->clk); -+ clk_prepare_enable(bs->clk); - bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS); - - /* register and we are done */ -@@ -509,7 +509,7 @@ static int bcm63xx_spi_probe(struct plat - return 0; - - out_clk_disable: -- clk_disable(clk); -+ clk_disable_unprepare(clk); - out_err: - platform_set_drvdata(pdev, NULL); - spi_master_put(master); -@@ -530,7 +530,7 @@ static int bcm63xx_spi_remove(struct pla - bcm_spi_writeb(bs, 0, SPI_INT_MASK); - - /* HW shutdown */ -- clk_disable(bs->clk); -+ clk_disable_unprepare(bs->clk); - clk_put(bs->clk); - - platform_set_drvdata(pdev, 0); -@@ -549,7 +549,7 @@ static int bcm63xx_spi_suspend(struct de - - spi_master_suspend(master); - -- clk_disable(bs->clk); -+ clk_disable_unprepare(bs->clk); - - return 0; - } -@@ -560,7 +560,7 @@ static int bcm63xx_spi_resume(struct dev - platform_get_drvdata(to_platform_device(dev)); - struct bcm63xx_spi *bs = spi_master_get_devdata(master); - -- clk_enable(bs->clk); -+ clk_prepare_enable(bs->clk); - - spi_master_resume(master); - diff --git a/target/linux/brcm63xx/patches-3.9/006-spi-bcm63xx-remove-duplicated-mode-bits-check.patch b/target/linux/brcm63xx/patches-3.9/006-spi-bcm63xx-remove-duplicated-mode-bits-check.patch deleted file mode 100644 index d387300f0f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/006-spi-bcm63xx-remove-duplicated-mode-bits-check.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 3abf34d4e0460bb098fabe3cc8207108bae1905a Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:40:26 +0100 -Subject: [PATCH 04/12] spi/bcm63xx: remove duplicated mode bits check - -The spi subsystem already checks the mode bits before calling setup. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 6 ------ - 1 file changed, 6 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -158,12 +158,6 @@ static int bcm63xx_spi_setup(struct spi_ - if (!spi->bits_per_word) - spi->bits_per_word = 8; - -- if (spi->mode & ~MODEBITS) { -- dev_err(&spi->dev, "%s, unsupported mode bits %x\n", -- __func__, spi->mode & ~MODEBITS); -- return -EINVAL; -- } -- - dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n", - __func__, spi->mode & MODEBITS, spi->bits_per_word, 0); - diff --git a/target/linux/brcm63xx/patches-3.9/007-spi-bcm63xx-remove-unneeded-debug-message.patch b/target/linux/brcm63xx/patches-3.9/007-spi-bcm63xx-remove-unneeded-debug-message.patch deleted file mode 100644 index a7fae946a9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/007-spi-bcm63xx-remove-unneeded-debug-message.patch +++ /dev/null @@ -1,26 +0,0 @@ -From ee18b0ac561afb9dd7d87a4217e80151a7e29dfc Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:42:22 +0100 -Subject: [PATCH 05/12] spi/bcm63xx: remove unneeded debug message - -The spi subsystem already provides this info in a more extensive -debug print except for the nsecs/bit - which wasn't calculated anyway -and fixed to 0. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 3 --- - 1 file changed, 3 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -158,9 +158,6 @@ static int bcm63xx_spi_setup(struct spi_ - if (!spi->bits_per_word) - spi->bits_per_word = 8; - -- dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n", -- __func__, spi->mode & MODEBITS, spi->bits_per_word, 0); -- - return 0; - } - diff --git a/target/linux/brcm63xx/patches-3.9/008-spi-bcm63xx-remove-unused-variable-bs-from-bcm63xx_s.patch b/target/linux/brcm63xx/patches-3.9/008-spi-bcm63xx-remove-unused-variable-bs-from-bcm63xx_s.patch deleted file mode 100644 index 81ea919c88..0000000000 --- a/target/linux/brcm63xx/patches-3.9/008-spi-bcm63xx-remove-unused-variable-bs-from-bcm63xx_s.patch +++ /dev/null @@ -1,26 +0,0 @@ -From 30151fe21befa84d9cd27d63f1bf3973988c811e Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:47:19 +0100 -Subject: [PATCH 06/12] spi/bcm63xx: remove unused variable bs from - bcm63xx_spi_setup - -It is only written, but never read. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 4 ---- - 1 file changed, 4 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -151,10 +151,6 @@ static void bcm63xx_spi_setup_transfer(s - - static int bcm63xx_spi_setup(struct spi_device *spi) - { -- struct bcm63xx_spi *bs; -- -- bs = spi_master_get_devdata(spi->master); -- - if (!spi->bits_per_word) - spi->bits_per_word = 8; - diff --git a/target/linux/brcm63xx/patches-3.9/009-spi-bcm63xx-check-spi-bits_per_word-in-spi_setup.patch b/target/linux/brcm63xx/patches-3.9/009-spi-bcm63xx-check-spi-bits_per_word-in-spi_setup.patch deleted file mode 100644 index 49a7ac27c7..0000000000 --- a/target/linux/brcm63xx/patches-3.9/009-spi-bcm63xx-check-spi-bits_per_word-in-spi_setup.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 13a364be644ed9b4666d452756556bb98afdcc56 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:48:27 +0100 -Subject: [PATCH 07/12] spi/bcm63xx: check spi bits_per_word in spi_setup - -Instead of fixing up the bits_per_word (which the spi subsystem already -does for us), check it for supported values. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 7 +++++-- - 1 file changed, 5 insertions(+), 2 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -151,8 +151,11 @@ static void bcm63xx_spi_setup_transfer(s - - static int bcm63xx_spi_setup(struct spi_device *spi) - { -- if (!spi->bits_per_word) -- spi->bits_per_word = 8; -+ if (spi->bits_per_word != 8) { -+ dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", -+ __func__, spi->bits_per_word); -+ return -EINVAL; -+ } - - return 0; - } diff --git a/target/linux/brcm63xx/patches-3.9/010-spi-bcm63xx-simplify-bcm63xx_spi_check_transfer.patch b/target/linux/brcm63xx/patches-3.9/010-spi-bcm63xx-simplify-bcm63xx_spi_check_transfer.patch deleted file mode 100644 index 57c1e465e0..0000000000 --- a/target/linux/brcm63xx/patches-3.9/010-spi-bcm63xx-simplify-bcm63xx_spi_check_transfer.patch +++ /dev/null @@ -1,30 +0,0 @@ -From d69ac73da38f0d16cc6b4524cd734b907db6eab8 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:51:10 +0100 -Subject: [PATCH 08/12] spi/bcm63xx: simplify bcm63xx_spi_check_transfer - -bcm63xx_spi_check_transfer is only called from one place that has -t always set, so directly check the transfer's bits_per_word. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 7 ++----- - 1 file changed, 2 insertions(+), 5 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -96,12 +96,9 @@ static const unsigned bcm63xx_spi_freq_t - static int bcm63xx_spi_check_transfer(struct spi_device *spi, - struct spi_transfer *t) - { -- u8 bits_per_word; -- -- bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word; -- if (bits_per_word != 8) { -+ if (t->bits_per_word != 8) { - dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", -- __func__, bits_per_word); -+ __func__, t->bits_per_word); - return -EINVAL; - } - diff --git a/target/linux/brcm63xx/patches-3.9/011-spi-bcm63xx-remove-spi-chip-select-validity-check.patch b/target/linux/brcm63xx/patches-3.9/011-spi-bcm63xx-remove-spi-chip-select-validity-check.patch deleted file mode 100644 index 4f1a1cc2a8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/011-spi-bcm63xx-remove-spi-chip-select-validity-check.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 9c5a988562468823a5e2973f04134a8bd97e7718 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:53:16 +0100 -Subject: [PATCH 09/12] spi/bcm63xx: remove spi chip select validity check - -The check would belong in bcm63xx_spi_setup if the spi subsystem -weren't already doing the check for us, so just drop it. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 6 ------ - 1 file changed, 6 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -102,12 +102,6 @@ static int bcm63xx_spi_check_transfer(st - return -EINVAL; - } - -- if (spi->chip_select > spi->master->num_chipselect) { -- dev_err(&spi->dev, "%s, unsupported slave %d\n", -- __func__, spi->chip_select); -- return -EINVAL; -- } -- - return 0; - } - diff --git a/target/linux/brcm63xx/patches-3.9/012-spi-bcm63xx-inline-bcm63xx_spi_check_transfer.patch b/target/linux/brcm63xx/patches-3.9/012-spi-bcm63xx-inline-bcm63xx_spi_check_transfer.patch deleted file mode 100644 index f684d83541..0000000000 --- a/target/linux/brcm63xx/patches-3.9/012-spi-bcm63xx-inline-bcm63xx_spi_check_transfer.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 3fffc5f76c830c375692a67948734168ee4c516a Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 13:59:30 +0100 -Subject: [PATCH 10/12] spi/bcm63xx: inline bcm63xx_spi_check_transfer - -It only does one check, so just do the check directly in the caller. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 19 +++++-------------- - 1 file changed, 5 insertions(+), 14 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -93,18 +93,6 @@ static const unsigned bcm63xx_spi_freq_t - { 391000, SPI_CLK_0_391MHZ } - }; - --static int bcm63xx_spi_check_transfer(struct spi_device *spi, -- struct spi_transfer *t) --{ -- if (t->bits_per_word != 8) { -- dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", -- __func__, t->bits_per_word); -- return -EINVAL; -- } -- -- return 0; --} -- - static void bcm63xx_spi_setup_transfer(struct spi_device *spi, - struct spi_transfer *t) - { -@@ -293,9 +281,12 @@ static int bcm63xx_spi_transfer_one(stru - * full-duplex transfers. - */ - list_for_each_entry(t, &m->transfers, transfer_list) { -- status = bcm63xx_spi_check_transfer(spi, t); -- if (status < 0) -+ if (t->bits_per_word != 8) { -+ dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", -+ __func__, t->bits_per_word); -+ status = -EINVAL; - goto exit; -+ } - - if (!first) - first = t; diff --git a/target/linux/brcm63xx/patches-3.9/013-spi-bcm63xx-inline-hz-usage-in-bcm63xx_spi_setup_tra.patch b/target/linux/brcm63xx/patches-3.9/013-spi-bcm63xx-inline-hz-usage-in-bcm63xx_spi_setup_tra.patch deleted file mode 100644 index fba37d57ad..0000000000 --- a/target/linux/brcm63xx/patches-3.9/013-spi-bcm63xx-inline-hz-usage-in-bcm63xx_spi_setup_tra.patch +++ /dev/null @@ -1,43 +0,0 @@ -From 2646be877afc663d1688a2add8386b027c9d7e31 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 14:08:06 +0100 -Subject: [PATCH 11/12] spi/bcm63xx: inline hz usage in - bcm63xx_spi_setup_transfer - -bcm63xx_spi_setup_transfer is called from only one place, and that has -t always set, to hz will always be t->speed_hz - just use it directly in -the two places instead of moving it in a local variable. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 7 ++----- - 1 file changed, 2 insertions(+), 5 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -97,15 +97,12 @@ static void bcm63xx_spi_setup_transfer(s - struct spi_transfer *t) - { - struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master); -- u32 hz; - u8 clk_cfg, reg; - int i; - -- hz = (t) ? t->speed_hz : spi->max_speed_hz; -- - /* Find the closest clock configuration */ - for (i = 0; i < SPI_CLK_MASK; i++) { -- if (hz >= bcm63xx_spi_freq_table[i][0]) { -+ if (t->speed_hz >= bcm63xx_spi_freq_table[i][0]) { - clk_cfg = bcm63xx_spi_freq_table[i][1]; - break; - } -@@ -122,7 +119,7 @@ static void bcm63xx_spi_setup_transfer(s - - bcm_spi_writeb(bs, reg, SPI_CLK_CFG); - dev_dbg(&spi->dev, "Setting clock register to %02x (hz %d)\n", -- clk_cfg, hz); -+ clk_cfg, t->speed_hz); - } - - /* the spi->mode bits understood by this driver: */ diff --git a/target/linux/brcm63xx/patches-3.9/014-spi-bcm63xx-use-devm_ioremap_resource.patch b/target/linux/brcm63xx/patches-3.9/014-spi-bcm63xx-use-devm_ioremap_resource.patch deleted file mode 100644 index 82fbe6c94b..0000000000 --- a/target/linux/brcm63xx/patches-3.9/014-spi-bcm63xx-use-devm_ioremap_resource.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 95af2d7751d31ea07b7a0d8ec7030f6c62df0ae2 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 11 Mar 2013 14:20:33 +0100 -Subject: [PATCH 12/12] spi/bcm63xx: use devm_ioremap_resource() - -Use devm_ioremap_resource() which provides its own error messages. - -Signed-off-by: Jonas Gorski ---- - drivers/spi/spi-bcm63xx.c | 15 +++------------ - 1 file changed, 3 insertions(+), 12 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -412,18 +412,9 @@ static int bcm63xx_spi_probe(struct plat - platform_set_drvdata(pdev, master); - bs->pdev = pdev; - -- if (!devm_request_mem_region(&pdev->dev, r->start, -- resource_size(r), PFX)) { -- dev_err(dev, "iomem request failed\n"); -- ret = -ENXIO; -- goto out_err; -- } -- -- bs->regs = devm_ioremap_nocache(&pdev->dev, r->start, -- resource_size(r)); -- if (!bs->regs) { -- dev_err(dev, "unable to ioremap regs\n"); -- ret = -ENOMEM; -+ bs->regs = devm_ioremap_resource(&pdev->dev, r); -+ if (IS_ERR(bs->regs)) { -+ ret = PTR_ERR(bs->regs); - goto out_err; - } - diff --git a/target/linux/brcm63xx/patches-3.9/015-spi-bcm63xx-remove-unused-speed_hz-member-variable.patch b/target/linux/brcm63xx/patches-3.9/015-spi-bcm63xx-remove-unused-speed_hz-member-variable.patch deleted file mode 100644 index d7b9327f61..0000000000 --- a/target/linux/brcm63xx/patches-3.9/015-spi-bcm63xx-remove-unused-speed_hz-member-variable.patch +++ /dev/null @@ -1,67 +0,0 @@ -From 5ff6b05a18295fa7e03de0fdf32d681a90b69df5 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 30 Mar 2013 10:26:55 +0100 -Subject: [PATCH] spi/bcm63xx: remove unused speed_hz member variable - -speed_hz is a write only member, so we can safely remove it and its -generation. Also fixes the missing clk_put after getting the periph -clock. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/dev-spi.c | 11 ----------- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 1 - - drivers/spi/spi-bcm63xx.c | 2 -- - 3 files changed, 14 deletions(-) - ---- a/arch/mips/bcm63xx/dev-spi.c -+++ b/arch/mips/bcm63xx/dev-spi.c -@@ -85,20 +85,9 @@ static struct platform_device bcm63xx_sp - - int __init bcm63xx_spi_register(void) - { -- struct clk *periph_clk; -- - if (BCMCPU_IS_6328() || BCMCPU_IS_6345()) - return -ENODEV; - -- periph_clk = clk_get(NULL, "periph"); -- if (IS_ERR(periph_clk)) { -- pr_err("unable to get periph clock\n"); -- return -ENODEV; -- } -- -- /* Set bus frequency */ -- spi_pdata.speed_hz = clk_get_rate(periph_clk); -- - spi_resources[0].start = bcm63xx_regset_address(RSET_SPI); - spi_resources[0].end = spi_resources[0].start; - spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -@@ -13,7 +13,6 @@ struct bcm63xx_spi_pdata { - unsigned int msg_ctl_width; - int bus_num; - int num_chipselect; -- u32 speed_hz; - }; - - enum bcm63xx_regs_spi { ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -46,7 +46,6 @@ struct bcm63xx_spi { - int irq; - - /* Platform data */ -- u32 speed_hz; - unsigned fifo_size; - unsigned int msg_type_shift; - unsigned int msg_ctl_width; -@@ -436,7 +435,6 @@ static int bcm63xx_spi_probe(struct plat - master->unprepare_transfer_hardware = bcm63xx_spi_unprepare_transfer; - master->transfer_one_message = bcm63xx_spi_transfer_one; - master->mode_bits = MODEBITS; -- bs->speed_hz = pdata->speed_hz; - bs->msg_type_shift = pdata->msg_type_shift; - bs->msg_ctl_width = pdata->msg_ctl_width; - bs->tx_io = (u8 *)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA)); diff --git a/target/linux/brcm63xx/patches-3.9/018-MIPS-BCM63XX-merge-bcm63xx_clk.h-into-bcm63xx-clk.c.patch b/target/linux/brcm63xx/patches-3.9/018-MIPS-BCM63XX-merge-bcm63xx_clk.h-into-bcm63xx-clk.c.patch deleted file mode 100644 index c3dedb47ba..0000000000 --- a/target/linux/brcm63xx/patches-3.9/018-MIPS-BCM63XX-merge-bcm63xx_clk.h-into-bcm63xx-clk.c.patch +++ /dev/null @@ -1,57 +0,0 @@ -From 715d03e5409fac9cbe76fd802db49ca15158378f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 30 Mar 2013 20:31:48 +0100 -Subject: [PATCH] MIPS: BCM63XX: merge bcm63xx_clk.h into bcm63xx/clk.c - -All the header file does is provide the internal structure of clk, -which shouldn't be used by anyone except clk.c itself anyway. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/clk.c | 8 +++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h | 11 ----------- - drivers/tty/serial/bcm63xx_uart.c | 1 - - 3 files changed, 7 insertions(+), 13 deletions(-) - delete mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -15,7 +15,13 @@ - #include - #include - #include --#include -+ -+struct clk { -+ void (*set)(struct clk *, int); -+ unsigned int rate; -+ unsigned int usage; -+ int id; -+}; - - static DEFINE_MUTEX(clocks_mutex); - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h -+++ /dev/null -@@ -1,11 +0,0 @@ --#ifndef BCM63XX_CLK_H_ --#define BCM63XX_CLK_H_ -- --struct clk { -- void (*set)(struct clk *, int); -- unsigned int rate; -- unsigned int usage; -- int id; --}; -- --#endif /* ! BCM63XX_CLK_H_ */ ---- a/drivers/tty/serial/bcm63xx_uart.c -+++ b/drivers/tty/serial/bcm63xx_uart.c -@@ -30,7 +30,6 @@ - #include - #include - --#include - #include - #include - #include diff --git a/target/linux/brcm63xx/patches-3.9/019-bcm63xx_enet-use-managed-io-memory-allocations.patch b/target/linux/brcm63xx/patches-3.9/019-bcm63xx_enet-use-managed-io-memory-allocations.patch deleted file mode 100644 index 5d0fb8ee26..0000000000 --- a/target/linux/brcm63xx/patches-3.9/019-bcm63xx_enet-use-managed-io-memory-allocations.patch +++ /dev/null @@ -1,118 +0,0 @@ -From 80b0356aea30e9fc9e075d31c2bf37e7cbfea8c9 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 10 Mar 2013 13:59:55 +0100 -Subject: [PATCH 1/3] bcm63xx_enet: use managed io memory allocations - -Signed-off-by: Jonas Gorski ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 43 +++++--------------------- - 1 file changed, 7 insertions(+), 36 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1619,7 +1619,6 @@ static int bcm_enet_probe(struct platfor - struct resource *res_mem, *res_irq, *res_irq_rx, *res_irq_tx; - struct mii_bus *bus; - const char *clk_name; -- unsigned int iomem_size; - int i, ret; - - /* stop if shared driver failed, assume driver->probe will be -@@ -1644,17 +1643,12 @@ static int bcm_enet_probe(struct platfor - if (ret) - goto out; - -- iomem_size = resource_size(res_mem); -- if (!request_mem_region(res_mem->start, iomem_size, "bcm63xx_enet")) { -- ret = -EBUSY; -- goto out; -- } -- -- priv->base = ioremap(res_mem->start, iomem_size); -+ priv->base = devm_request_and_ioremap(&pdev->dev, res_mem); - if (priv->base == NULL) { - ret = -ENOMEM; -- goto out_release_mem; -+ goto out; - } -+ - dev->irq = priv->irq = res_irq->start; - priv->irq_rx = res_irq_rx->start; - priv->irq_tx = res_irq_tx->start; -@@ -1674,7 +1668,7 @@ static int bcm_enet_probe(struct platfor - priv->mac_clk = clk_get(&pdev->dev, clk_name); - if (IS_ERR(priv->mac_clk)) { - ret = PTR_ERR(priv->mac_clk); -- goto out_unmap; -+ goto out; - } - clk_enable(priv->mac_clk); - -@@ -1814,12 +1808,6 @@ out_uninit_hw: - out_put_clk_mac: - clk_disable(priv->mac_clk); - clk_put(priv->mac_clk); -- --out_unmap: -- iounmap(priv->base); -- --out_release_mem: -- release_mem_region(res_mem->start, iomem_size); - out: - free_netdev(dev); - return ret; -@@ -1833,7 +1821,6 @@ static int bcm_enet_remove(struct platfo - { - struct bcm_enet_priv *priv; - struct net_device *dev; -- struct resource *res; - - /* stop netdevice */ - dev = platform_get_drvdata(pdev); -@@ -1856,11 +1843,6 @@ static int bcm_enet_remove(struct platfo - bcm_enet_mdio_write_mii); - } - -- /* release device resources */ -- iounmap(priv->base); -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- release_mem_region(res->start, resource_size(res)); -- - /* disable hw block clocks */ - if (priv->phy_clk) { - clk_disable(priv->phy_clk); -@@ -1889,31 +1871,20 @@ struct platform_driver bcm63xx_enet_driv - static int bcm_enet_shared_probe(struct platform_device *pdev) - { - struct resource *res; -- unsigned int iomem_size; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - return -ENODEV; - -- iomem_size = resource_size(res); -- if (!request_mem_region(res->start, iomem_size, "bcm63xx_enet_dma")) -- return -EBUSY; -- -- bcm_enet_shared_base = ioremap(res->start, iomem_size); -- if (!bcm_enet_shared_base) { -- release_mem_region(res->start, iomem_size); -+ bcm_enet_shared_base = devm_request_and_ioremap(&pdev->dev, res); -+ if (!bcm_enet_shared_base) - return -ENOMEM; -- } -+ - return 0; - } - - static int bcm_enet_shared_remove(struct platform_device *pdev) - { -- struct resource *res; -- -- iounmap(bcm_enet_shared_base); -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- release_mem_region(res->start, resource_size(res)); - return 0; - } - diff --git a/target/linux/brcm63xx/patches-3.9/020-bcm63xx_enet-use-managed-memory-allocations.patch b/target/linux/brcm63xx/patches-3.9/020-bcm63xx_enet-use-managed-memory-allocations.patch deleted file mode 100644 index d121fce152..0000000000 --- a/target/linux/brcm63xx/patches-3.9/020-bcm63xx_enet-use-managed-memory-allocations.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 451a609ca472f80838df056689359c5486d832c1 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 10 Mar 2013 14:05:01 +0100 -Subject: [PATCH 2/3] bcm63xx_enet: use managed memory allocations - -Signed-off-by: Jonas Gorski ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 8 +++----- - 1 file changed, 3 insertions(+), 5 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1727,7 +1727,8 @@ static int bcm_enet_probe(struct platfor - * if a slave is not present on hw */ - bus->phy_mask = ~(1 << priv->phy_id); - -- bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL); -+ bus->irq = devm_kzalloc(&pdev->dev, sizeof(int) * PHY_MAX_ADDR, -+ GFP_KERNEL); - if (!bus->irq) { - ret = -ENOMEM; - goto out_free_mdio; -@@ -1788,10 +1789,8 @@ static int bcm_enet_probe(struct platfor - return 0; - - out_unregister_mdio: -- if (priv->mii_bus) { -+ if (priv->mii_bus) - mdiobus_unregister(priv->mii_bus); -- kfree(priv->mii_bus->irq); -- } - - out_free_mdio: - if (priv->mii_bus) -@@ -1832,7 +1831,6 @@ static int bcm_enet_remove(struct platfo - - if (priv->has_phy) { - mdiobus_unregister(priv->mii_bus); -- kfree(priv->mii_bus->irq); - mdiobus_free(priv->mii_bus); - } else { - struct bcm63xx_enet_platform_data *pd; diff --git a/target/linux/brcm63xx/patches-3.9/021-bcm63xx_enet-properly-prepare-unprepare-clocks-befor.patch b/target/linux/brcm63xx/patches-3.9/021-bcm63xx_enet-properly-prepare-unprepare-clocks-befor.patch deleted file mode 100644 index 5f05685d1f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/021-bcm63xx_enet-properly-prepare-unprepare-clocks-befor.patch +++ /dev/null @@ -1,62 +0,0 @@ -From 8d6b746129f11efe4ba69aeb2c982359d33c6ec3 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 10 Sep 2012 01:28:47 +0200 -Subject: [PATCH 3/3] bcm63xx_enet: properly prepare/unprepare clocks - before/after usage - -Use clk_prepare_enable/disable_unprepare calls in preparation for -switching to the generic clock framework. - -Signed-off-by: Jonas Gorski ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++------ - 1 file changed, 6 insertions(+), 6 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1670,7 +1670,7 @@ static int bcm_enet_probe(struct platfor - ret = PTR_ERR(priv->mac_clk); - goto out; - } -- clk_enable(priv->mac_clk); -+ clk_prepare_enable(priv->mac_clk); - - /* initialize default and fetch platform data */ - priv->rx_ring_size = BCMENET_DEF_RX_DESC; -@@ -1699,7 +1699,7 @@ static int bcm_enet_probe(struct platfor - priv->phy_clk = NULL; - goto out_put_clk_mac; - } -- clk_enable(priv->phy_clk); -+ clk_prepare_enable(priv->phy_clk); - } - - /* do minimal hardware init to be able to probe mii bus */ -@@ -1800,12 +1800,12 @@ out_uninit_hw: - /* turn off mdc clock */ - enet_writel(priv, 0, ENET_MIISC_REG); - if (priv->phy_clk) { -- clk_disable(priv->phy_clk); -+ clk_disable_unprepare(priv->phy_clk); - clk_put(priv->phy_clk); - } - - out_put_clk_mac: -- clk_disable(priv->mac_clk); -+ clk_disable_unprepare(priv->mac_clk); - clk_put(priv->mac_clk); - out: - free_netdev(dev); -@@ -1843,10 +1843,10 @@ static int bcm_enet_remove(struct platfo - - /* disable hw block clocks */ - if (priv->phy_clk) { -- clk_disable(priv->phy_clk); -+ clk_disable_unprepare(priv->phy_clk); - clk_put(priv->phy_clk); - } -- clk_disable(priv->mac_clk); -+ clk_disable_unprepare(priv->mac_clk); - clk_put(priv->mac_clk); - - platform_set_drvdata(pdev, NULL); diff --git a/target/linux/brcm63xx/patches-3.9/022-MIPS-BCM63XX-remove-duplicate-spi-register-definitio.patch b/target/linux/brcm63xx/patches-3.9/022-MIPS-BCM63XX-remove-duplicate-spi-register-definitio.patch deleted file mode 100644 index 50bbb93255..0000000000 --- a/target/linux/brcm63xx/patches-3.9/022-MIPS-BCM63XX-remove-duplicate-spi-register-definitio.patch +++ /dev/null @@ -1,166 +0,0 @@ -From e1a3ace7260fad338a76595b116a6bf5b5627aa2 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 7 Mar 2013 12:20:10 +0100 -Subject: [PATCH 1/7] MIPS: BCM63XX: remove duplicate spi register definitions - -BCM6338 and BCM6348, and BCM6358 and everything after that share the -same register layout. To not have to redefine them for each new chip -and keep the code size small, only use the definitions for the first -chip with the certain layout. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/dev-spi.c | 24 +++--------- - .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 10 +---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 40 +------------------- - 3 files changed, 10 insertions(+), 64 deletions(-) - ---- a/arch/mips/bcm63xx/dev-spi.c -+++ b/arch/mips/bcm63xx/dev-spi.c -@@ -22,10 +22,6 @@ - /* - * register offsets - */ --static const unsigned long bcm6338_regs_spi[] = { -- __GEN_SPI_REGS_TABLE(6338) --}; -- - static const unsigned long bcm6348_regs_spi[] = { - __GEN_SPI_REGS_TABLE(6348) - }; -@@ -34,23 +30,15 @@ static const unsigned long bcm6358_regs_ - __GEN_SPI_REGS_TABLE(6358) - }; - --static const unsigned long bcm6368_regs_spi[] = { -- __GEN_SPI_REGS_TABLE(6368) --}; -- - const unsigned long *bcm63xx_regs_spi; - EXPORT_SYMBOL(bcm63xx_regs_spi); - - static __init void bcm63xx_spi_regs_init(void) - { -- if (BCMCPU_IS_6338()) -- bcm63xx_regs_spi = bcm6338_regs_spi; -- if (BCMCPU_IS_6348()) -+ if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) - bcm63xx_regs_spi = bcm6348_regs_spi; -- if (BCMCPU_IS_6358()) -+ if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) - bcm63xx_regs_spi = bcm6358_regs_spi; -- if (BCMCPU_IS_6368()) -- bcm63xx_regs_spi = bcm6368_regs_spi; - } - #else - static __init void bcm63xx_spi_regs_init(void) { } -@@ -93,10 +81,10 @@ int __init bcm63xx_spi_register(void) - spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI); - - if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) { -- spi_resources[0].end += BCM_6338_RSET_SPI_SIZE - 1; -- spi_pdata.fifo_size = SPI_6338_MSG_DATA_SIZE; -- spi_pdata.msg_type_shift = SPI_6338_MSG_TYPE_SHIFT; -- spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH; -+ spi_resources[0].end += BCM_6348_RSET_SPI_SIZE - 1; -+ spi_pdata.fifo_size = SPI_6348_MSG_DATA_SIZE; -+ spi_pdata.msg_type_shift = SPI_6348_MSG_TYPE_SHIFT; -+ spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH; - } - - if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) { ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -@@ -71,18 +71,12 @@ static inline unsigned long bcm63xx_spir - - return bcm63xx_regs_spi[reg]; - #else --#ifdef CONFIG_BCM63XX_CPU_6338 -- __GEN_SPI_RSET(6338) --#endif --#ifdef CONFIG_BCM63XX_CPU_6348 -+#if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348) - __GEN_SPI_RSET(6348) - #endif --#ifdef CONFIG_BCM63XX_CPU_6358 -+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368) - __GEN_SPI_RSET(6358) - #endif --#ifdef CONFIG_BCM63XX_CPU_6368 -- __GEN_SPI_RSET(6368) --#endif - #endif - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1223,24 +1223,7 @@ - * _REG relative to RSET_SPI - *************************************************************************/ - --/* BCM 6338 SPI core */ --#define SPI_6338_CMD 0x00 /* 16-bits register */ --#define SPI_6338_INT_STATUS 0x02 --#define SPI_6338_INT_MASK_ST 0x03 --#define SPI_6338_INT_MASK 0x04 --#define SPI_6338_ST 0x05 --#define SPI_6338_CLK_CFG 0x06 --#define SPI_6338_FILL_BYTE 0x07 --#define SPI_6338_MSG_TAIL 0x09 --#define SPI_6338_RX_TAIL 0x0b --#define SPI_6338_MSG_CTL 0x40 /* 8-bits register */ --#define SPI_6338_MSG_CTL_WIDTH 8 --#define SPI_6338_MSG_DATA 0x41 --#define SPI_6338_MSG_DATA_SIZE 0x3f --#define SPI_6338_RX_DATA 0x80 --#define SPI_6338_RX_DATA_SIZE 0x3f -- --/* BCM 6348 SPI core */ -+/* BCM 6338/6348 SPI core */ - #define SPI_6348_CMD 0x00 /* 16-bits register */ - #define SPI_6348_INT_STATUS 0x02 - #define SPI_6348_INT_MASK_ST 0x03 -@@ -1257,7 +1240,7 @@ - #define SPI_6348_RX_DATA 0x80 - #define SPI_6348_RX_DATA_SIZE 0x3f - --/* BCM 6358 SPI core */ -+/* BCM 6358/6368 SPI core */ - #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */ - #define SPI_6358_MSG_CTL_WIDTH 16 - #define SPI_6358_MSG_DATA 0x02 -@@ -1274,23 +1257,6 @@ - #define SPI_6358_MSG_TAIL 0x709 - #define SPI_6358_RX_TAIL 0x70B - --/* BCM 6358 SPI core */ --#define SPI_6368_MSG_CTL 0x00 /* 16-bits register */ --#define SPI_6368_MSG_CTL_WIDTH 16 --#define SPI_6368_MSG_DATA 0x02 --#define SPI_6368_MSG_DATA_SIZE 0x21e --#define SPI_6368_RX_DATA 0x400 --#define SPI_6368_RX_DATA_SIZE 0x220 --#define SPI_6368_CMD 0x700 /* 16-bits register */ --#define SPI_6368_INT_STATUS 0x702 --#define SPI_6368_INT_MASK_ST 0x703 --#define SPI_6368_INT_MASK 0x704 --#define SPI_6368_ST 0x705 --#define SPI_6368_CLK_CFG 0x706 --#define SPI_6368_FILL_BYTE 0x707 --#define SPI_6368_MSG_TAIL 0x709 --#define SPI_6368_RX_TAIL 0x70B -- - /* Shared SPI definitions */ - - /* Message configuration */ -@@ -1298,10 +1264,8 @@ - #define SPI_HD_W 0x01 - #define SPI_HD_R 0x02 - #define SPI_BYTE_CNT_SHIFT 0 --#define SPI_6338_MSG_TYPE_SHIFT 6 - #define SPI_6348_MSG_TYPE_SHIFT 6 - #define SPI_6358_MSG_TYPE_SHIFT 14 --#define SPI_6368_MSG_TYPE_SHIFT 14 - - /* Command */ - #define SPI_CMD_NOOP 0x00 diff --git a/target/linux/brcm63xx/patches-3.9/023-MIPS-BCM63XX-fix-revision-ID-width.patch b/target/linux/brcm63xx/patches-3.9/023-MIPS-BCM63XX-fix-revision-ID-width.patch deleted file mode 100644 index 0ee88e113c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/023-MIPS-BCM63XX-fix-revision-ID-width.patch +++ /dev/null @@ -1,68 +0,0 @@ -From 609c69339a24bd034f5359dad14087276ce5a83f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 15 Jan 2012 14:41:22 +0100 -Subject: [PATCH 2/7] MIPS: BCM63XX: fix revision ID width - -The REVID is only 8 bit wide. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/cpu.c | 4 ++-- - arch/mips/bcm63xx/setup.c | 2 +- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 2 +- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 +- - 4 files changed, 5 insertions(+), 5 deletions(-) - ---- a/arch/mips/bcm63xx/cpu.c -+++ b/arch/mips/bcm63xx/cpu.c -@@ -25,7 +25,7 @@ const int *bcm63xx_irqs; - EXPORT_SYMBOL(bcm63xx_irqs); - - static u16 bcm63xx_cpu_id; --static u16 bcm63xx_cpu_rev; -+static u8 bcm63xx_cpu_rev; - static unsigned int bcm63xx_cpu_freq; - static unsigned int bcm63xx_memory_size; - -@@ -87,7 +87,7 @@ u16 __bcm63xx_get_cpu_id(void) - - EXPORT_SYMBOL(__bcm63xx_get_cpu_id); - --u16 bcm63xx_get_cpu_rev(void) -+u8 bcm63xx_get_cpu_rev(void) - { - return bcm63xx_cpu_rev; - } ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -126,7 +126,7 @@ static void __bcm63xx_machine_reboot(cha - const char *get_system_type(void) - { - static char buf[128]; -- snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%04X)", -+ snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%02X)", - board_get_name(), - bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev()); - return buf; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -18,7 +18,7 @@ - - void __init bcm63xx_cpu_init(void); - u16 __bcm63xx_get_cpu_id(void); --u16 bcm63xx_get_cpu_rev(void); -+u8 bcm63xx_get_cpu_rev(void); - unsigned int bcm63xx_get_cpu_freq(void); - - #ifdef CONFIG_BCM63XX_CPU_6328 ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -10,7 +10,7 @@ - #define REV_CHIPID_SHIFT 16 - #define REV_CHIPID_MASK (0xffff << REV_CHIPID_SHIFT) - #define REV_REVID_SHIFT 0 --#define REV_REVID_MASK (0xffff << REV_REVID_SHIFT) -+#define REV_REVID_MASK (0xff << REV_REVID_SHIFT) - - /* Clock Control register */ - #define PERF_CKCTL_REG 0x4 diff --git a/target/linux/brcm63xx/patches-3.9/024-MIPS-BCM63XX-rework-chip-detection.patch b/target/linux/brcm63xx/patches-3.9/024-MIPS-BCM63XX-rework-chip-detection.patch deleted file mode 100644 index 0ff9edf74b..0000000000 --- a/target/linux/brcm63xx/patches-3.9/024-MIPS-BCM63XX-rework-chip-detection.patch +++ /dev/null @@ -1,133 +0,0 @@ -From 3f4570c9794fcae1cf62fbf3266a2e23edac67a5 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Wed, 27 Jun 2012 15:01:09 +0200 -Subject: [PATCH 3/7] MIPS: BCM63XX: rework chip detection - -Instead of trying to use a correlation of cpu prid and chip id and -hoping they will always be unique, use the cpu prid to determine the -chip id register location and just read out the chip id. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/cpu.c | 87 +++++++++++++++++++++++------------------------ - 1 file changed, 42 insertions(+), 45 deletions(-) - ---- a/arch/mips/bcm63xx/cpu.c -+++ b/arch/mips/bcm63xx/cpu.c -@@ -240,53 +240,27 @@ static unsigned int detect_memory_size(v - - void __init bcm63xx_cpu_init(void) - { -- unsigned int tmp, expected_cpu_id; -+ unsigned int tmp; - struct cpuinfo_mips *c = ¤t_cpu_data; - unsigned int cpu = smp_processor_id(); -+ u32 chipid_reg; - - /* soc registers location depends on cpu type */ -- expected_cpu_id = 0; -+ chipid_reg = 0; - - switch (c->cputype) { - case CPU_BMIPS3300: -- if ((read_c0_prid() & 0xff00) == PRID_IMP_BMIPS3300_ALT) { -- expected_cpu_id = BCM6348_CPU_ID; -- bcm63xx_regs_base = bcm6348_regs_base; -- bcm63xx_irqs = bcm6348_irqs; -- } else { -+ if ((read_c0_prid() & 0xff00) != PRID_IMP_BMIPS3300_ALT) - __cpu_name[cpu] = "Broadcom BCM6338"; -- expected_cpu_id = BCM6338_CPU_ID; -- bcm63xx_regs_base = bcm6338_regs_base; -- bcm63xx_irqs = bcm6338_irqs; -- } -- break; -+ /* fall-through */ - case CPU_BMIPS32: -- expected_cpu_id = BCM6345_CPU_ID; -- bcm63xx_regs_base = bcm6345_regs_base; -- bcm63xx_irqs = bcm6345_irqs; -+ chipid_reg = BCM_6345_PERF_BASE; - break; - case CPU_BMIPS4350: -- if ((read_c0_prid() & 0xf0) == 0x10) { -- expected_cpu_id = BCM6358_CPU_ID; -- bcm63xx_regs_base = bcm6358_regs_base; -- bcm63xx_irqs = bcm6358_irqs; -- } else { -- /* all newer chips have the same chip id location */ -- u16 chip_id = bcm_readw(BCM_6368_PERF_BASE); -- -- switch (chip_id) { -- case BCM6328_CPU_ID: -- expected_cpu_id = BCM6328_CPU_ID; -- bcm63xx_regs_base = bcm6328_regs_base; -- bcm63xx_irqs = bcm6328_irqs; -- break; -- case BCM6368_CPU_ID: -- expected_cpu_id = BCM6368_CPU_ID; -- bcm63xx_regs_base = bcm6368_regs_base; -- bcm63xx_irqs = bcm6368_irqs; -- break; -- } -- } -+ if ((read_c0_prid() & 0xf0) == 0x10) -+ chipid_reg = BCM_6345_PERF_BASE; -+ else -+ chipid_reg = BCM_6368_PERF_BASE; - break; - } - -@@ -294,20 +268,43 @@ void __init bcm63xx_cpu_init(void) - * really early to panic, but delaying panic would not help since we - * will never get any working console - */ -- if (!expected_cpu_id) -+ if (!chipid_reg) - panic("unsupported Broadcom CPU"); - -- /* -- * bcm63xx_regs_base is set, we can access soc registers -- */ -- -- /* double check CPU type */ -- tmp = bcm_perf_readl(PERF_REV_REG); -+ /* read out CPU type */ -+ tmp = bcm_readl(chipid_reg); - bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT; - bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT; - -- if (bcm63xx_cpu_id != expected_cpu_id) -- panic("bcm63xx CPU id mismatch"); -+ switch (bcm63xx_cpu_id) { -+ case BCM6328_CPU_ID: -+ bcm63xx_regs_base = bcm6328_regs_base; -+ bcm63xx_irqs = bcm6328_irqs; -+ break; -+ case BCM6338_CPU_ID: -+ bcm63xx_regs_base = bcm6338_regs_base; -+ bcm63xx_irqs = bcm6338_irqs; -+ break; -+ case BCM6345_CPU_ID: -+ bcm63xx_regs_base = bcm6345_regs_base; -+ bcm63xx_irqs = bcm6345_irqs; -+ break; -+ case BCM6348_CPU_ID: -+ bcm63xx_regs_base = bcm6348_regs_base; -+ bcm63xx_irqs = bcm6348_irqs; -+ break; -+ case BCM6358_CPU_ID: -+ bcm63xx_regs_base = bcm6358_regs_base; -+ bcm63xx_irqs = bcm6358_irqs; -+ break; -+ case BCM6368_CPU_ID: -+ bcm63xx_regs_base = bcm6368_regs_base; -+ bcm63xx_irqs = bcm6368_irqs; -+ break; -+ default: -+ panic("unsupported broadcom CPU %x", bcm63xx_cpu_id); -+ break; -+ } - - bcm63xx_cpu_freq = detect_cpu_clock(); - bcm63xx_memory_size = detect_memory_size(); diff --git a/target/linux/brcm63xx/patches-3.9/025-MIPS-BCM63XX-add-basic-BCM6362-support.patch b/target/linux/brcm63xx/patches-3.9/025-MIPS-BCM63XX-add-basic-BCM6362-support.patch deleted file mode 100644 index 53a64975f7..0000000000 --- a/target/linux/brcm63xx/patches-3.9/025-MIPS-BCM63XX-add-basic-BCM6362-support.patch +++ /dev/null @@ -1,575 +0,0 @@ -From 1071a9c9527d68eca4605e2eb1686609bfecf287 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 21 Nov 2011 00:48:52 +0100 -Subject: [PATCH 4/7] MIPS: BCM63XX: add basic BCM6362 support - -Add basic support for detecting and booting the BCM6362. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/Kconfig | 4 + - arch/mips/bcm63xx/boards/board_bcm963xx.c | 6 +- - arch/mips/bcm63xx/cpu.c | 51 +++++++- - arch/mips/bcm63xx/irq.c | 22 ++++ - arch/mips/bcm63xx/prom.c | 2 + - arch/mips/bcm63xx/reset.c | 28 +++++ - arch/mips/bcm63xx/setup.c | 3 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 139 +++++++++++++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h | 2 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 61 ++++++++- - arch/mips/include/asm/mach-bcm63xx/ioremap.h | 1 + - 11 files changed, 314 insertions(+), 5 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -25,6 +25,10 @@ config BCM63XX_CPU_6358 - bool "support 6358 CPU" - select HW_HAS_PCI - -+config BCM63XX_CPU_6362 -+ bool "support 6362 CPU" -+ select HW_HAS_PCI -+ - config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select HW_HAS_PCI ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -726,11 +726,11 @@ void __init board_prom_init(void) - u32 val; - - /* read base address of boot chip select (0) -- * 6328 does not have MPI but boots from a fixed address -+ * 6328/6362 do not have MPI but boot from a fixed address - */ -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { - val = 0x18000000; -- else { -+ } else { - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); - val &= MPI_CSBASE_BASE_MASK; - } ---- a/arch/mips/bcm63xx/cpu.c -+++ b/arch/mips/bcm63xx/cpu.c -@@ -71,6 +71,15 @@ static const int bcm6358_irqs[] = { - - }; - -+static const unsigned long bcm6362_regs_base[] = { -+ __GEN_CPU_REGS_TABLE(6362) -+}; -+ -+static const int bcm6362_irqs[] = { -+ __GEN_CPU_IRQ_TABLE(6362) -+ -+}; -+ - static const unsigned long bcm6368_regs_base[] = { - __GEN_CPU_REGS_TABLE(6368) - }; -@@ -169,6 +178,42 @@ static unsigned int detect_cpu_clock(voi - return (16 * 1000000 * n1 * n2) / m1; - } - -+ case BCM6362_CPU_ID: -+ { -+ unsigned int tmp, mips_pll_fcvo; -+ -+ tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG); -+ mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK) -+ >> STRAPBUS_6362_FCVO_SHIFT; -+ switch (mips_pll_fcvo) { -+ case 0x03: -+ case 0x0b: -+ case 0x13: -+ case 0x1b: -+ return 240000000; -+ case 0x04: -+ case 0x0c: -+ case 0x14: -+ case 0x1c: -+ return 160000000; -+ case 0x05: -+ case 0x0e: -+ case 0x16: -+ case 0x1e: -+ case 0x1f: -+ return 400000000; -+ case 0x06: -+ return 440000000; -+ case 0x07: -+ case 0x17: -+ return 384000000; -+ case 0x15: -+ case 0x1d: -+ return 200000000; -+ default: -+ return 320000000; -+ } -+ } - case BCM6368_CPU_ID: - { - unsigned int tmp, p1, p2, ndiv, m1; -@@ -205,7 +250,7 @@ static unsigned int detect_memory_size(v - unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0; - u32 val; - -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) - return bcm_ddr_readl(DDR_CSEND_REG) << 24; - - if (BCMCPU_IS_6345()) { -@@ -297,6 +342,10 @@ void __init bcm63xx_cpu_init(void) - bcm63xx_regs_base = bcm6358_regs_base; - bcm63xx_irqs = bcm6358_irqs; - break; -+ case BCM6362_CPU_ID: -+ bcm63xx_regs_base = bcm6362_regs_base; -+ bcm63xx_irqs = bcm6362_irqs; -+ break; - case BCM6368_CPU_ID: - bcm63xx_regs_base = bcm6368_regs_base; - bcm63xx_irqs = bcm6368_irqs; ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -82,6 +82,17 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6358 - #define ext_irq_cfg_reg2 0 - #endif -+#ifdef CONFIG_BCM63XX_CPU_6362 -+#define irq_stat_reg PERF_IRQSTAT_6362_REG -+#define irq_mask_reg PERF_IRQMASK_6362_REG -+#define irq_bits 64 -+#define is_ext_irq_cascaded 1 -+#define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE) -+#define ext_irq_end (BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE) -+#define ext_irq_count 4 -+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6362 -+#define ext_irq_cfg_reg2 0 -+#endif - #ifdef CONFIG_BCM63XX_CPU_6368 - #define irq_stat_reg PERF_IRQSTAT_6368_REG - #define irq_mask_reg PERF_IRQMASK_6368_REG -@@ -170,6 +181,16 @@ static void bcm63xx_init_irq(void) - ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358; - break; -+ case BCM6362_CPU_ID: -+ irq_stat_addr += PERF_IRQSTAT_6362_REG; -+ irq_mask_addr += PERF_IRQMASK_6362_REG; -+ irq_bits = 64; -+ ext_irq_count = 4; -+ is_ext_irq_cascaded = 1; -+ ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE; -+ ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE; -+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362; -+ break; - case BCM6368_CPU_ID: - irq_stat_addr += PERF_IRQSTAT_6368_REG; - irq_mask_addr += PERF_IRQMASK_6368_REG; -@@ -458,6 +479,7 @@ static int bcm63xx_external_irq_set_type - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: - case BCM6358_CPU_ID: -+ case BCM6362_CPU_ID: - case BCM6368_CPU_ID: - if (levelsense) - reg |= EXTIRQ_CFG_LEVELSENSE(irq); ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -36,6 +36,8 @@ void __init prom_init(void) - mask = CKCTL_6348_ALL_SAFE_EN; - else if (BCMCPU_IS_6358()) - mask = CKCTL_6358_ALL_SAFE_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_ALL_SAFE_EN; - else if (BCMCPU_IS_6368()) - mask = CKCTL_6368_ALL_SAFE_EN; - else ---- a/arch/mips/bcm63xx/reset.c -+++ b/arch/mips/bcm63xx/reset.c -@@ -85,6 +85,20 @@ - #define BCM6358_RESET_PCIE 0 - #define BCM6358_RESET_PCIE_EXT 0 - -+#define BCM6362_RESET_SPI SOFTRESET_6362_SPI_MASK -+#define BCM6362_RESET_ENET 0 -+#define BCM6362_RESET_USBH SOFTRESET_6362_USBH_MASK -+#define BCM6362_RESET_USBD SOFTRESET_6362_USBS_MASK -+#define BCM6362_RESET_DSL 0 -+#define BCM6362_RESET_SAR SOFTRESET_6362_SAR_MASK -+#define BCM6362_RESET_EPHY SOFTRESET_6362_EPHY_MASK -+#define BCM6362_RESET_ENETSW SOFTRESET_6362_ENETSW_MASK -+#define BCM6362_RESET_PCM SOFTRESET_6362_PCM_MASK -+#define BCM6362_RESET_MPI 0 -+#define BCM6362_RESET_PCIE (SOFTRESET_6362_PCIE_MASK | \ -+ SOFTRESET_6362_PCIE_CORE_MASK) -+#define BCM6362_RESET_PCIE_EXT SOFTRESET_6362_PCIE_EXT_MASK -+ - #define BCM6368_RESET_SPI SOFTRESET_6368_SPI_MASK - #define BCM6368_RESET_ENET 0 - #define BCM6368_RESET_USBH SOFTRESET_6368_USBH_MASK -@@ -119,6 +133,10 @@ static const u32 bcm6358_reset_bits[] = - __GEN_RESET_BITS_TABLE(6358) - }; - -+static const u32 bcm6362_reset_bits[] = { -+ __GEN_RESET_BITS_TABLE(6362) -+}; -+ - static const u32 bcm6368_reset_bits[] = { - __GEN_RESET_BITS_TABLE(6368) - }; -@@ -140,6 +158,9 @@ static int __init bcm63xx_reset_bits_ini - } else if (BCMCPU_IS_6358()) { - reset_reg = PERF_SOFTRESET_6358_REG; - bcm63xx_reset_bits = bcm6358_reset_bits; -+ } else if (BCMCPU_IS_6362()) { -+ reset_reg = PERF_SOFTRESET_6362_REG; -+ bcm63xx_reset_bits = bcm6362_reset_bits; - } else if (BCMCPU_IS_6368()) { - reset_reg = PERF_SOFTRESET_6368_REG; - bcm63xx_reset_bits = bcm6368_reset_bits; -@@ -182,6 +203,13 @@ static const u32 bcm63xx_reset_bits[] = - #define reset_reg PERF_SOFTRESET_6358_REG - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+static const u32 bcm63xx_reset_bits[] = { -+ __GEN_RESET_BITS_TABLE(6362) -+}; -+#define reset_reg PERF_SOFTRESET_6362_REG -+#endif -+ - #ifdef CONFIG_BCM63XX_CPU_6368 - static const u32 bcm63xx_reset_bits[] = { - __GEN_RESET_BITS_TABLE(6368) ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -83,6 +83,9 @@ void bcm63xx_machine_reboot(void) - case BCM6358_CPU_ID: - perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358; - break; -+ case BCM6362_CPU_ID: -+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362; -+ break; - } - - for (i = 0; i < 2; i++) { ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -14,6 +14,7 @@ - #define BCM6345_CPU_ID 0x6345 - #define BCM6348_CPU_ID 0x6348 - #define BCM6358_CPU_ID 0x6358 -+#define BCM6362_CPU_ID 0x6362 - #define BCM6368_CPU_ID 0x6368 - - void __init bcm63xx_cpu_init(void); -@@ -86,6 +87,20 @@ unsigned int bcm63xx_get_cpu_freq(void); - # define BCMCPU_IS_6358() (0) - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+# ifdef bcm63xx_get_cpu_id -+# undef bcm63xx_get_cpu_id -+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id() -+# define BCMCPU_RUNTIME_DETECT -+# else -+# define bcm63xx_get_cpu_id() BCM6362_CPU_ID -+# endif -+# define BCMCPU_IS_6362() (bcm63xx_get_cpu_id() == BCM6362_CPU_ID) -+#else -+# define BCMCPU_IS_6362() (0) -+#endif -+ -+ - #ifdef CONFIG_BCM63XX_CPU_6368 - # ifdef bcm63xx_get_cpu_id - # undef bcm63xx_get_cpu_id -@@ -406,6 +421,62 @@ enum bcm63xx_regs_set { - - - /* -+ * 6362 register sets base address -+ */ -+#define BCM_6362_DSL_LMEM_BASE (0xdeadbeef) -+#define BCM_6362_PERF_BASE (0xb0000000) -+#define BCM_6362_TIMER_BASE (0xb0000040) -+#define BCM_6362_WDT_BASE (0xb000005c) -+#define BCM_6362_UART0_BASE (0xb0000100) -+#define BCM_6362_UART1_BASE (0xb0000120) -+#define BCM_6362_GPIO_BASE (0xb0000080) -+#define BCM_6362_SPI_BASE (0xb0000800) -+#define BCM_6362_HSSPI_BASE (0xb0001000) -+#define BCM_6362_UDC0_BASE (0xdeadbeef) -+#define BCM_6362_USBDMA_BASE (0xb000c000) -+#define BCM_6362_OHCI0_BASE (0xb0002600) -+#define BCM_6362_OHCI_PRIV_BASE (0xdeadbeef) -+#define BCM_6362_USBH_PRIV_BASE (0xb0002700) -+#define BCM_6362_USBD_BASE (0xb0002400) -+#define BCM_6362_MPI_BASE (0xdeadbeef) -+#define BCM_6362_PCMCIA_BASE (0xdeadbeef) -+#define BCM_6362_PCIE_BASE (0xb0e40000) -+#define BCM_6362_SDRAM_REGS_BASE (0xdeadbeef) -+#define BCM_6362_DSL_BASE (0xdeadbeef) -+#define BCM_6362_UBUS_BASE (0xdeadbeef) -+#define BCM_6362_ENET0_BASE (0xdeadbeef) -+#define BCM_6362_ENET1_BASE (0xdeadbeef) -+#define BCM_6362_ENETDMA_BASE (0xb000d800) -+#define BCM_6362_ENETDMAC_BASE (0xb000da00) -+#define BCM_6362_ENETDMAS_BASE (0xb000dc00) -+#define BCM_6362_ENETSW_BASE (0xb0e00000) -+#define BCM_6362_EHCI0_BASE (0xb0002500) -+#define BCM_6362_SDRAM_BASE (0xdeadbeef) -+#define BCM_6362_MEMC_BASE (0xdeadbeef) -+#define BCM_6362_DDR_BASE (0xb0003000) -+#define BCM_6362_M2M_BASE (0xdeadbeef) -+#define BCM_6362_ATM_BASE (0xdeadbeef) -+#define BCM_6362_XTM_BASE (0xb0007800) -+#define BCM_6362_XTMDMA_BASE (0xb000b800) -+#define BCM_6362_XTMDMAC_BASE (0xdeadbeef) -+#define BCM_6362_XTMDMAS_BASE (0xdeadbeef) -+#define BCM_6362_PCM_BASE (0xb000a800) -+#define BCM_6362_PCMDMA_BASE (0xdeadbeef) -+#define BCM_6362_PCMDMAC_BASE (0xdeadbeef) -+#define BCM_6362_PCMDMAS_BASE (0xdeadbeef) -+#define BCM_6362_RNG_BASE (0xdeadbeef) -+#define BCM_6362_MISC_BASE (0xb0001800) -+ -+#define BCM_6362_NAND_REG_BASE (0xb0000200) -+#define BCM_6362_NAND_CACHE_BASE (0xb0000600) -+#define BCM_6362_LED_BASE (0xb0001900) -+#define BCM_6362_IPSEC_BASE (0xb0002800) -+#define BCM_6362_IPSEC_DMA_BASE (0xb000d000) -+#define BCM_6362_WLAN_CHIPCOMMON_BASE (0xb0004000) -+#define BCM_6362_WLAN_D11_BASE (0xb0005000) -+#define BCM_6362_WLAN_SHIM_BASE (0xb0007000) -+ -+/* - * 6368 register sets base address - */ - #define BCM_6368_DSL_LMEM_BASE (0xdeadbeef) -@@ -564,6 +635,9 @@ static inline unsigned long bcm63xx_regs - #ifdef CONFIG_BCM63XX_CPU_6358 - __GEN_RSET(6358) - #endif -+#ifdef CONFIG_BCM63XX_CPU_6362 -+ __GEN_RSET(6362) -+#endif - #ifdef CONFIG_BCM63XX_CPU_6368 - __GEN_RSET(6368) - #endif -@@ -820,6 +894,71 @@ enum bcm63xx_irq { - #define BCM_6358_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28) - - /* -+ * 6362 irqs -+ */ -+#define BCM_6362_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) -+ -+#define BCM_6362_TIMER_IRQ (IRQ_INTERNAL_BASE + 0) -+#define BCM_6362_SPI_IRQ (IRQ_INTERNAL_BASE + 2) -+#define BCM_6362_UART0_IRQ (IRQ_INTERNAL_BASE + 3) -+#define BCM_6362_UART1_IRQ (IRQ_INTERNAL_BASE + 4) -+#define BCM_6362_DSL_IRQ (IRQ_INTERNAL_BASE + 28) -+#define BCM_6362_UDC0_IRQ 0 -+#define BCM_6362_ENET0_IRQ 0 -+#define BCM_6362_ENET1_IRQ 0 -+#define BCM_6362_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 14) -+#define BCM_6362_HSSPI_IRQ (IRQ_INTERNAL_BASE + 5) -+#define BCM_6362_OHCI0_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6362_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) -+#define BCM_6362_USBD_IRQ (IRQ_INTERNAL_BASE + 11) -+#define BCM_6362_USBD_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 20) -+#define BCM_6362_USBD_TXDMA0_IRQ (IRQ_INTERNAL_BASE + 21) -+#define BCM_6362_USBD_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 22) -+#define BCM_6362_USBD_TXDMA1_IRQ (IRQ_INTERNAL_BASE + 23) -+#define BCM_6362_USBD_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 24) -+#define BCM_6362_USBD_TXDMA2_IRQ (IRQ_INTERNAL_BASE + 25) -+#define BCM_6362_PCMCIA_IRQ 0 -+#define BCM_6362_ENET0_RXDMA_IRQ 0 -+#define BCM_6362_ENET0_TXDMA_IRQ 0 -+#define BCM_6362_ENET1_RXDMA_IRQ 0 -+#define BCM_6362_ENET1_TXDMA_IRQ 0 -+#define BCM_6362_PCI_IRQ (IRQ_INTERNAL_BASE + 30) -+#define BCM_6362_ATM_IRQ 0 -+#define BCM_6362_ENETSW_RXDMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 0) -+#define BCM_6362_ENETSW_RXDMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 1) -+#define BCM_6362_ENETSW_RXDMA2_IRQ (BCM_6362_HIGH_IRQ_BASE + 2) -+#define BCM_6362_ENETSW_RXDMA3_IRQ (BCM_6362_HIGH_IRQ_BASE + 3) -+#define BCM_6362_ENETSW_TXDMA0_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA1_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA2_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA3_IRQ 0 -+#define BCM_6362_XTM_IRQ 0 -+#define BCM_6362_XTM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 12) -+ -+#define BCM_6362_RING_OSC_IRQ (IRQ_INTERNAL_BASE + 1) -+#define BCM_6362_WLAN_GPIO_IRQ (IRQ_INTERNAL_BASE + 6) -+#define BCM_6362_WLAN_IRQ (IRQ_INTERNAL_BASE + 7) -+#define BCM_6362_IPSEC_IRQ (IRQ_INTERNAL_BASE + 8) -+#define BCM_6362_NAND_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6362_PCM_IRQ (IRQ_INTERNAL_BASE + 13) -+#define BCM_6362_DG_IRQ (IRQ_INTERNAL_BASE + 15) -+#define BCM_6362_EPHY_ENERGY0_IRQ (IRQ_INTERNAL_BASE + 16) -+#define BCM_6362_EPHY_ENERGY1_IRQ (IRQ_INTERNAL_BASE + 17) -+#define BCM_6362_EPHY_ENERGY2_IRQ (IRQ_INTERNAL_BASE + 18) -+#define BCM_6362_EPHY_ENERGY3_IRQ (IRQ_INTERNAL_BASE + 19) -+#define BCM_6362_IPSEC_DMA0_IRQ (IRQ_INTERNAL_BASE + 26) -+#define BCM_6362_IPSEC_DMA1_IRQ (IRQ_INTERNAL_BASE + 27) -+#define BCM_6362_FAP0_IRQ (IRQ_INTERNAL_BASE + 29) -+#define BCM_6362_PCM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 4) -+#define BCM_6362_PCM_DMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 5) -+#define BCM_6362_DECT0_IRQ (BCM_6362_HIGH_IRQ_BASE + 6) -+#define BCM_6362_DECT1_IRQ (BCM_6362_HIGH_IRQ_BASE + 7) -+#define BCM_6362_EXT_IRQ0 (BCM_6362_HIGH_IRQ_BASE + 8) -+#define BCM_6362_EXT_IRQ1 (BCM_6362_HIGH_IRQ_BASE + 9) -+#define BCM_6362_EXT_IRQ2 (BCM_6362_HIGH_IRQ_BASE + 10) -+#define BCM_6362_EXT_IRQ3 (BCM_6362_HIGH_IRQ_BASE + 11) -+ -+/* - * 6368 irqs - */ - #define BCM_6368_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -@@ -17,6 +17,8 @@ static inline unsigned long bcm63xx_gpio - return 8; - case BCM6345_CPU_ID: - return 16; -+ case BCM6362_CPU_ID: -+ return 48; - case BCM6368_CPU_ID: - return 38; - case BCM6348_CPU_ID: ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -112,6 +112,39 @@ - CKCTL_6358_USBSU_EN | \ - CKCTL_6358_EPHY_EN) - -+#define CKCTL_6362_ADSL_QPROC_EN (1 << 1) -+#define CKCTL_6362_ADSL_AFE_EN (1 << 2) -+#define CKCTL_6362_ADSL_EN (1 << 3) -+#define CKCTL_6362_MIPS_EN (1 << 4) -+#define CKCTL_6362_WLAN_OCP_EN (1 << 5) -+#define CKCTL_6362_SWPKT_USB_EN (1 << 7) -+#define CKCTL_6362_SWPKT_SAR_EN (1 << 8) -+#define CKCTL_6362_SAR_EN (1 << 9) -+#define CKCTL_6362_ROBOSW_EN (1 << 10) -+#define CKCTL_6362_PCM_EN (1 << 11) -+#define CKCTL_6362_USBD_EN (1 << 12) -+#define CKCTL_6362_USBH_EN (1 << 13) -+#define CKCTL_6362_IPSEC_EN (1 << 14) -+#define CKCTL_6362_SPI_EN (1 << 15) -+#define CKCTL_6362_HSSPI_EN (1 << 16) -+#define CKCTL_6362_PCIE_EN (1 << 17) -+#define CKCTL_6362_FAP_EN (1 << 18) -+#define CKCTL_6362_PHYMIPS_EN (1 << 19) -+#define CKCTL_6362_NAND_EN (1 << 20) -+ -+#define CKCTL_6362_ALL_SAFE_EN (CKCTL_6362_PHYMIPS_EN | \ -+ CKCTL_6362_ADSL_QPROC_EN | \ -+ CKCTL_6362_ADSL_AFE_EN | \ -+ CKCTL_6362_ADSL_EN | \ -+ CKCTL_6362_SAR_EN | \ -+ CKCTL_6362_PCM_EN | \ -+ CKCTL_6362_IPSEC_EN | \ -+ CKCTL_6362_USBD_EN | \ -+ CKCTL_6362_USBH_EN | \ -+ CKCTL_6362_ROBOSW_EN | \ -+ CKCTL_6362_PCIE_EN) -+ -+ - #define CKCTL_6368_VDSL_QPROC_EN (1 << 2) - #define CKCTL_6368_VDSL_AFE_EN (1 << 3) - #define CKCTL_6368_VDSL_BONDING_EN (1 << 4) -@@ -153,6 +186,7 @@ - #define PERF_IRQMASK_6345_REG 0xc - #define PERF_IRQMASK_6348_REG 0xc - #define PERF_IRQMASK_6358_REG 0xc -+#define PERF_IRQMASK_6362_REG 0x20 - #define PERF_IRQMASK_6368_REG 0x20 - - /* Interrupt Status register */ -@@ -161,6 +195,7 @@ - #define PERF_IRQSTAT_6345_REG 0x10 - #define PERF_IRQSTAT_6348_REG 0x10 - #define PERF_IRQSTAT_6358_REG 0x10 -+#define PERF_IRQSTAT_6362_REG 0x28 - #define PERF_IRQSTAT_6368_REG 0x28 - - /* External Interrupt Configuration register */ -@@ -169,6 +204,7 @@ - #define PERF_EXTIRQ_CFG_REG_6345 0x14 - #define PERF_EXTIRQ_CFG_REG_6348 0x14 - #define PERF_EXTIRQ_CFG_REG_6358 0x14 -+#define PERF_EXTIRQ_CFG_REG_6362 0x18 - #define PERF_EXTIRQ_CFG_REG_6368 0x18 - - #define PERF_EXTIRQ_CFG_REG2_6368 0x1c -@@ -197,6 +233,7 @@ - #define PERF_SOFTRESET_REG 0x28 - #define PERF_SOFTRESET_6328_REG 0x10 - #define PERF_SOFTRESET_6358_REG 0x34 -+#define PERF_SOFTRESET_6362_REG 0x10 - #define PERF_SOFTRESET_6368_REG 0x10 - - #define SOFTRESET_6328_SPI_MASK (1 << 0) -@@ -259,6 +296,22 @@ - #define SOFTRESET_6358_PCM_MASK (1 << 13) - #define SOFTRESET_6358_ADSL_MASK (1 << 14) - -+#define SOFTRESET_6362_SPI_MASK (1 << 0) -+#define SOFTRESET_6362_IPSEC_MASK (1 << 1) -+#define SOFTRESET_6362_EPHY_MASK (1 << 2) -+#define SOFTRESET_6362_SAR_MASK (1 << 3) -+#define SOFTRESET_6362_ENETSW_MASK (1 << 4) -+#define SOFTRESET_6362_USBS_MASK (1 << 5) -+#define SOFTRESET_6362_USBH_MASK (1 << 6) -+#define SOFTRESET_6362_PCM_MASK (1 << 7) -+#define SOFTRESET_6362_PCIE_CORE_MASK (1 << 8) -+#define SOFTRESET_6362_PCIE_MASK (1 << 9) -+#define SOFTRESET_6362_PCIE_EXT_MASK (1 << 10) -+#define SOFTRESET_6362_WLAN_SHIM_MASK (1 << 11) -+#define SOFTRESET_6362_DDR_PHY_MASK (1 << 12) -+#define SOFTRESET_6362_FAP_MASK (1 << 13) -+#define SOFTRESET_6362_WLAN_UBUS_MASK (1 << 14) -+ - #define SOFTRESET_6368_SPI_MASK (1 << 0) - #define SOFTRESET_6368_MPI_MASK (1 << 3) - #define SOFTRESET_6368_EPHY_MASK (1 << 6) -@@ -1240,7 +1293,7 @@ - #define SPI_6348_RX_DATA 0x80 - #define SPI_6348_RX_DATA_SIZE 0x3f - --/* BCM 6358/6368 SPI core */ -+/* BCM 6358/6262/6368 SPI core */ - #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */ - #define SPI_6358_MSG_CTL_WIDTH 16 - #define SPI_6358_MSG_DATA 0x02 -@@ -1316,6 +1369,12 @@ - #define SERDES_PCIE_EN (1 << 0) - #define SERDES_PCIE_EXD_EN (1 << 15) - -+#define MISC_STRAPBUS_6362_REG 0x14 -+#define STRAPBUS_6362_FCVO_SHIFT 1 -+#define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT) -+#define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15) -+#define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) -+ - #define MISC_STRAPBUS_6328_REG 0x240 - #define STRAPBUS_6328_FCVO_SHIFT 7 - #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) ---- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h -+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h -@@ -19,6 +19,7 @@ static inline int is_bcm63xx_internal_re - return 1; - break; - case BCM6328_CPU_ID: -+ case BCM6362_CPU_ID: - case BCM6368_CPU_ID: - if (offset >= 0xb0000000 && offset < 0xb1000000) - return 1; diff --git a/target/linux/brcm63xx/patches-3.9/026-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.9/026-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch deleted file mode 100644 index 27a411de39..0000000000 --- a/target/linux/brcm63xx/patches-3.9/026-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch +++ /dev/null @@ -1,57 +0,0 @@ -From 5da349ee614f61a2e6edb403098f40c6d40f2553 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 5 Jul 2012 21:19:20 +0200 -Subject: [PATCH 5/7] MIPS: BCM63XX: enable SPI controller for BCM6362 - -The SPI controller shares the same register layout as the 6358 one. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/clk.c | 2 ++ - arch/mips/bcm63xx/dev-spi.c | 4 ++-- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 3 ++- - 3 files changed, 6 insertions(+), 3 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -202,6 +202,8 @@ static void spi_set(struct clk *clk, int - mask = CKCTL_6348_SPI_EN; - else if (BCMCPU_IS_6358()) - mask = CKCTL_6358_SPI_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_SPI_EN; - else - /* BCMCPU_IS_6368 */ - mask = CKCTL_6368_SPI_EN; ---- a/arch/mips/bcm63xx/dev-spi.c -+++ b/arch/mips/bcm63xx/dev-spi.c -@@ -37,7 +37,7 @@ static __init void bcm63xx_spi_regs_init - { - if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) - bcm63xx_regs_spi = bcm6348_regs_spi; -- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) -+ if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) - bcm63xx_regs_spi = bcm6358_regs_spi; - } - #else -@@ -87,7 +87,7 @@ int __init bcm63xx_spi_register(void) - spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH; - } - -- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) { -+ if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { - spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1; - spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE; - spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -@@ -74,7 +74,8 @@ static inline unsigned long bcm63xx_spir - #if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348) - __GEN_SPI_RSET(6348) - #endif --#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368) -+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6362) || \ -+ defined(CONFIG_BCM63XX_CPU_6368) - __GEN_SPI_RSET(6358) - #endif - #endif diff --git a/target/linux/brcm63xx/patches-3.9/027-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.9/027-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch deleted file mode 100644 index 3c5b11901e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/027-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch +++ /dev/null @@ -1,56 +0,0 @@ -From ec6f1e53b22d01e628b79b99f7a33960034e97e7 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 21 Nov 2011 00:53:26 +0100 -Subject: [PATCH 6/7] MIPS: BCM63XX: enable pcie for BCM6362 - -The PCIe controller is almost the same as the BCM6328 one, with only -the SERDES register being at a different location. - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 3 ++- - arch/mips/pci/pci-bcm63xx.c | 11 +++++++++-- - 2 files changed, 11 insertions(+), 3 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1365,7 +1365,8 @@ - /************************************************************************* - * _REG relative to RSET_MISC - *************************************************************************/ --#define MISC_SERDES_CTRL_REG 0x0 -+#define MISC_SERDES_CTRL_6328_REG 0x0 -+#define MISC_SERDES_CTRL_6362_REG 0x4 - #define SERDES_PCIE_EN (1 << 0) - #define SERDES_PCIE_EXD_EN (1 << 15) - ---- a/arch/mips/pci/pci-bcm63xx.c -+++ b/arch/mips/pci/pci-bcm63xx.c -@@ -121,11 +121,17 @@ void __iomem *pci_iospace_start; - static void __init bcm63xx_reset_pcie(void) - { - u32 val; -+ u32 reg; - - /* enable SERDES */ -- val = bcm_misc_readl(MISC_SERDES_CTRL_REG); -+ if (BCMCPU_IS_6328()) -+ reg = MISC_SERDES_CTRL_6328_REG; -+ else -+ reg = MISC_SERDES_CTRL_6362_REG; -+ -+ val = bcm_misc_readl(reg); - val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN; -- bcm_misc_writel(val, MISC_SERDES_CTRL_REG); -+ bcm_misc_writel(val, reg); - - /* reset the PCIe core */ - bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1); -@@ -330,6 +336,7 @@ static int __init bcm63xx_pci_init(void) - - switch (bcm63xx_get_cpu_id()) { - case BCM6328_CPU_ID: -+ case BCM6362_CPU_ID: - return bcm63xx_register_pcie(); - case BCM6348_CPU_ID: - case BCM6358_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.9/028-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.9/028-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch deleted file mode 100644 index 38125a50e9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/028-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 01034e48e72783ced82a050e862f82ee3dfdb783 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 21 Nov 2011 00:48:52 +0100 -Subject: [PATCH 7/7] MIPS: BCM63XX: add flash detection for BCM6362 - -BCM6362 support booting from SPI flash and NAND. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/dev-flash.c | 6 ++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 1 + - 2 files changed, 7 insertions(+) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -77,6 +77,12 @@ static int __init bcm63xx_detect_flash_t - return BCM63XX_FLASH_TYPE_PARALLEL; - else - return BCM63XX_FLASH_TYPE_SERIAL; -+ case BCM6362_CPU_ID: -+ val = bcm_misc_readl(MISC_STRAPBUS_6362_REG); -+ if (val & STRAPBUS_6362_BOOT_SEL_SERIAL) -+ return BCM63XX_FLASH_TYPE_SERIAL; -+ else -+ return BCM63XX_FLASH_TYPE_NAND; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1372,6 +1372,7 @@ - - #define MISC_STRAPBUS_6362_REG 0x14 - #define STRAPBUS_6362_FCVO_SHIFT 1 -+#define STRAPBUS_6362_HSSPI_CLK_FAST (1 << 13) - #define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT) - #define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15) - #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) diff --git a/target/linux/brcm63xx/patches-3.9/029-MIPS-BCM63XX-add-missing-clocks-for-BCM6328-and-BCM6.patch b/target/linux/brcm63xx/patches-3.9/029-MIPS-BCM63XX-add-missing-clocks-for-BCM6328-and-BCM6.patch deleted file mode 100644 index bc72a0035e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/029-MIPS-BCM63XX-add-missing-clocks-for-BCM6328-and-BCM6.patch +++ /dev/null @@ -1,91 +0,0 @@ -From d31454bc822e1957e758e75d4367bcd12af89743 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 18 Apr 2013 21:23:11 +0200 -Subject: [PATCH] MIPS: BCM63XX: add missing clocks for BCM6328 and BCM6362 - -Add currently unused missing clocks for BCM6328 and BCM6362. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/clk.c | 33 +++++++++++++++++++++++++-------- - 1 file changed, 25 insertions(+), 8 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -125,11 +125,18 @@ static struct clk clk_ephy = { - */ - static void enetsw_set(struct clk *clk, int enable) - { -- if (!BCMCPU_IS_6368()) -+ if (BCMCPU_IS_6328()) -+ bcm_hwclock_set(CKCTL_6328_ROBOSW_EN, enable); -+ else if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_ROBOSW_EN, enable); -+ else if (BCMCPU_IS_6368()) -+ bcm_hwclock_set(CKCTL_6368_ROBOSW_EN | -+ CKCTL_6368_SWPKT_USB_EN | -+ CKCTL_6368_SWPKT_SAR_EN, -+ enable); -+ else - return; -- bcm_hwclock_set(CKCTL_6368_ROBOSW_EN | -- CKCTL_6368_SWPKT_USB_EN | -- CKCTL_6368_SWPKT_SAR_EN, enable); -+ - if (enable) { - /* reset switch core afer clock change */ - bcm63xx_core_set_reset(BCM63XX_RESET_ENETSW, 1); -@@ -166,6 +173,8 @@ static void usbh_set(struct clk *clk, in - bcm_hwclock_set(CKCTL_6328_USBH_EN, enable); - else if (BCMCPU_IS_6348()) - bcm_hwclock_set(CKCTL_6348_USBH_EN, enable); -+ else if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); - else if (BCMCPU_IS_6368()) - bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); - } -@@ -181,6 +190,8 @@ static void usbd_set(struct clk *clk, in - { - if (BCMCPU_IS_6328()) - bcm_hwclock_set(CKCTL_6328_USBD_EN, enable); -+ else if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_USBD_EN, enable); - else if (BCMCPU_IS_6368()) - bcm_hwclock_set(CKCTL_6368_USBD_EN, enable); - } -@@ -244,7 +255,10 @@ static struct clk clk_xtm = { - */ - static void ipsec_set(struct clk *clk, int enable) - { -- bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable); -+ if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_IPSEC_EN, enable); -+ else if (BCMCPU_IS_6368()) -+ bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable); - } - - static struct clk clk_ipsec = { -@@ -257,7 +271,10 @@ static struct clk clk_ipsec = { - - static void pcie_set(struct clk *clk, int enable) - { -- bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable); -+ if (BCMCPU_IS_6328()) -+ bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable); -+ else if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_PCIE_EN, enable); - } - - static struct clk clk_pcie = { -@@ -323,9 +340,9 @@ struct clk *clk_get(struct device *dev, - return &clk_periph; - if (BCMCPU_IS_6358() && !strcmp(id, "pcm")) - return &clk_pcm; -- if (BCMCPU_IS_6368() && !strcmp(id, "ipsec")) -+ if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec")) - return &clk_ipsec; -- if (BCMCPU_IS_6328() && !strcmp(id, "pcie")) -+ if ((BCMCPU_IS_6328() || BCMCPU_IS_6362()) && !strcmp(id, "pcie")) - return &clk_pcie; - return ERR_PTR(-ENOENT); - } diff --git a/target/linux/brcm63xx/patches-3.9/030-MTD-bcm63xxpart-use-size-macro-for-CFE-block-size.patch b/target/linux/brcm63xx/patches-3.9/030-MTD-bcm63xxpart-use-size-macro-for-CFE-block-size.patch deleted file mode 100644 index a7f782276a..0000000000 --- a/target/linux/brcm63xx/patches-3.9/030-MTD-bcm63xxpart-use-size-macro-for-CFE-block-size.patch +++ /dev/null @@ -1,29 +0,0 @@ -From e2092cf1b164ede62b740c7c95905171fb6232ff Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 23 Mar 2013 12:32:56 +0100 -Subject: [PATCH v2 1/3] MTD: bcm63xxpart: use size macro for CFE block size - -Signed-off-by: Jonas Gorski ---- - drivers/mtd/bcm63xxpart.c | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -27,6 +27,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -37,7 +38,7 @@ - - #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */ - --#define BCM63XX_CFE_BLOCK_SIZE 0x10000 /* always at least 64KiB */ -+#define BCM63XX_CFE_BLOCK_SIZE SZ_64K /* always at least 64KiB */ - - #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0 - diff --git a/target/linux/brcm63xx/patches-3.9/031-MIPS-BCM63XX-export-PSI-size-from-nvram.patch b/target/linux/brcm63xx/patches-3.9/031-MIPS-BCM63XX-export-PSI-size-from-nvram.patch deleted file mode 100644 index 8ff9659b57..0000000000 --- a/target/linux/brcm63xx/patches-3.9/031-MIPS-BCM63XX-export-PSI-size-from-nvram.patch +++ /dev/null @@ -1,58 +0,0 @@ -From bda508f975d1372568a4fc9862be501a6176fd46 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 12 May 2012 23:04:17 +0200 -Subject: [PATCH v2 2/3] MIPS: BCM63XX: export PSI size from nvram - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/nvram.c | 13 +++++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h | 7 +++++++ - 2 files changed, 20 insertions(+) - ---- a/arch/mips/bcm63xx/nvram.c -+++ b/arch/mips/bcm63xx/nvram.c -@@ -15,6 +15,7 @@ - #include - #include - #include -+#include - - #include - -@@ -35,6 +36,8 @@ struct bcm963xx_nvram { - u32 checksum_high; - }; - -+#define BCM63XX_DEFAULT_PSI_SIZE SZ_64K -+ - static struct bcm963xx_nvram nvram; - static int mac_addr_used; - -@@ -104,3 +107,13 @@ int bcm63xx_nvram_get_mac_address(u8 *ma - return 0; - } - EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address); -+ -+unsigned int bcm63xx_nvram_get_psi_size(void) -+{ -+ /* max is 64k, but some vendors use higher values */ -+ if (nvram.psi_size > 0 && nvram.psi_size <= 512) -+ return nvram.psi_size * SZ_1K; -+ -+ return BCM63XX_DEFAULT_PSI_SIZE; -+} -+EXPORT_SYMBOL(bcm63xx_nvram_get_psi_size); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h -@@ -30,4 +30,11 @@ u8 *bcm63xx_nvram_get_name(void); - */ - int bcm63xx_nvram_get_mac_address(u8 *mac); - -+/** -+ * bcm63xx_nvram_get_psi_size() - returns the size of the PSI area -+ * -+ * Returns the size of the Persitent Storage Information area in bytes. -+ */ -+unsigned int bcm63xx_nvram_get_psi_size(void); -+ - #endif /* BCM63XX_NVRAM_H */ diff --git a/target/linux/brcm63xx/patches-3.9/032-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch b/target/linux/brcm63xx/patches-3.9/032-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch deleted file mode 100644 index f1c1a0fa88..0000000000 --- a/target/linux/brcm63xx/patches-3.9/032-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch +++ /dev/null @@ -1,42 +0,0 @@ -From f6eefaa4a08ec27c69485c2fc4db23247b84f8c9 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 1 May 2012 14:10:39 +0200 -Subject: [PATCH v2 3/3] MTD: bcm63xxpart: use nvram for PSI size - -Read out the SPI size from nvram instead of defaulting to 64K - some -vendors actually use values larger than the "max" value of 64. - -Signed-off-by: Jonas Gorski ---- - drivers/mtd/bcm63xxpart.c | 6 ++++-- - 1 file changed, 4 insertions(+), 2 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -4,7 +4,7 @@ - * Copyright © 2006-2008 Florian Fainelli - * Mike Albon - * Copyright © 2009-2010 Daniel Dickinson -- * Copyright © 2011-2012 Jonas Gorski -+ * Copyright © 2011-2013 Jonas Gorski - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by -@@ -34,6 +34,7 @@ - #include - - #include -+#include - #include - - #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */ -@@ -91,7 +92,8 @@ static int bcm63xx_parse_cfe_partitions( - BCM63XX_CFE_BLOCK_SIZE); - - cfelen = cfe_erasesize; -- nvramlen = cfe_erasesize; -+ nvramlen = bcm63xx_nvram_get_psi_size(); -+ nvramlen = roundup(nvramlen, cfe_erasesize); - - /* Allocate memory for buffer */ - buf = vmalloc(sizeof(struct bcm_tag)); diff --git a/target/linux/brcm63xx/patches-3.9/033-MIPS-BCM63XX-Handle-SW-IRQs-0-1.patch b/target/linux/brcm63xx/patches-3.9/033-MIPS-BCM63XX-Handle-SW-IRQs-0-1.patch deleted file mode 100644 index 38fd2d8740..0000000000 --- a/target/linux/brcm63xx/patches-3.9/033-MIPS-BCM63XX-Handle-SW-IRQs-0-1.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 1a66581c94ad3966a823f2efaf8a5cc514895318 Mon Sep 17 00:00:00 2001 -From: Kevin Cernekee -Date: Mon, 31 Oct 2011 11:52:10 -0700 -Subject: [PATCH 2/3] MIPS: BCM63XX: Handle SW IRQs 0-1 - -MIPS software IRQs 0 and 1 are used for interprocessor signaling (IPI) -on BMIPS SMP. Make the board support code aware of them. - -Signed-off-by: Kevin Cernekee -[jogo@openwrt.org: move sw irqs behind timer irq] -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -294,6 +294,10 @@ asmlinkage void plat_irq_dispatch(void) - - if (cause & CAUSEF_IP7) - do_IRQ(7); -+ if (cause & CAUSEF_IP0) -+ do_IRQ(0); -+ if (cause & CAUSEF_IP1) -+ do_IRQ(1); - if (cause & CAUSEF_IP2) - dispatch_internal(); - if (!is_ext_irq_cascaded) { diff --git a/target/linux/brcm63xx/patches-3.9/034-MIPS-BCM63XX-select-BMIPS4350-and-default-to-2-CPUs-.patch b/target/linux/brcm63xx/patches-3.9/034-MIPS-BCM63XX-select-BMIPS4350-and-default-to-2-CPUs-.patch deleted file mode 100644 index 920bc39200..0000000000 --- a/target/linux/brcm63xx/patches-3.9/034-MIPS-BCM63XX-select-BMIPS4350-and-default-to-2-CPUs-.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 158a11f25e070a6ed99cf8faa985da1f2669230f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 21 Apr 2013 14:44:00 +0200 -Subject: [PATCH 3/3] MIPS: BCM63XX: select BMIPS4350 and default to 2 CPUs - for supported SoCs - -All BCM63XX SoCs starting with BCM6358 have a BMIPS4350 instead of a -BMIPS3300, so select it unless support for any of the older SoCs is -selected. -All BMIPS4350 have only two CPUs, so select the appropriate default. - -Signed-off-by: Jonas Gorski ---- - arch/mips/Kconfig | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/arch/mips/Kconfig -+++ b/arch/mips/Kconfig -@@ -129,6 +129,8 @@ config BCM63XX - select DMA_NONCOHERENT - select IRQ_CPU - select SYS_HAS_CPU_MIPS32_R1 -+ select SYS_HAS_CPU_BMIPS4350 if !BCM63XX_CPU_6338 && !BCM63XX_CPU_6345 && !BCM63XX_CPU_6348 -+ select NR_CPUS_DEFAULT_2 - select SYS_SUPPORTS_32BIT_KERNEL - select SYS_SUPPORTS_BIG_ENDIAN - select SYS_HAS_EARLY_PRINTK diff --git a/target/linux/brcm63xx/patches-3.9/035-MIPS-BCM63XX-select-BOOT_RAW.patch b/target/linux/brcm63xx/patches-3.9/035-MIPS-BCM63XX-select-BOOT_RAW.patch deleted file mode 100644 index c540536cd8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/035-MIPS-BCM63XX-select-BOOT_RAW.patch +++ /dev/null @@ -1,30 +0,0 @@ -From 373eb1a286bf31b41f966d5d3826cfe63e826c92 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:39 +0000 -Subject: [PATCH 1/6] MIPS: BCM63XX: select BOOT_RAW - -Enabling BOOT_RAW is mandatory to get a binary image (objcopy from ELF -to binary) to work. This does not affect the ELF kernels which are used -by CFE on BCM63XX DSL platforms, but is going to be necessary to support -BCM63XX on Cable Modem chips such as BCM3368. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Patchwork: https://patchwork.linux-mips.org/patch/5500/ -Signed-off-by: Ralf Baechle ---- - arch/mips/Kconfig | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/mips/Kconfig -+++ b/arch/mips/Kconfig -@@ -124,6 +124,7 @@ config BCM47XX - - config BCM63XX - bool "Broadcom BCM63XX based boards" -+ select BOOT_RAW - select CEVT_R4K - select CSRC_R4K - select DMA_NONCOHERENT diff --git a/target/linux/brcm63xx/patches-3.9/036-MIPS-BCM63XX-add-support-for-BCM3368-Cable-Modem.patch b/target/linux/brcm63xx/patches-3.9/036-MIPS-BCM63XX-add-support-for-BCM3368-Cable-Modem.patch deleted file mode 100644 index c33776325b..0000000000 --- a/target/linux/brcm63xx/patches-3.9/036-MIPS-BCM63XX-add-support-for-BCM3368-Cable-Modem.patch +++ /dev/null @@ -1,629 +0,0 @@ -From 31c761c9c1fa91bf4ed83d75dcbc4e426ea2b670 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:40 +0000 -Subject: [PATCH 2/6] MIPS: BCM63XX: add support for BCM3368 Cable Modem - -The Broadcom BCM3368 Cable Modem SoC is extremely similar to the -existing BCM63xx DSL SoCs, in particular BCM6358, therefore little effort -in the existing code base is required to get it supported. This patch adds -support for the following on-chip peripherals: - -- two UARTS -- GPIO -- Ethernet -- SPI -- PCI -- NOR Flash - -The most noticeable difference with 3368 is that it has its peripheral -register at 0xfff8_0000 we check that separately in ioremap.h. Since -3368 is identical to 6358 for its clock and reset bits, we use them -verbatim. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Patchwork: https://patchwork.linux-mips.org/patch/5499/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/Kconfig | 4 + - arch/mips/bcm63xx/clk.c | 18 ++-- - arch/mips/bcm63xx/cpu.c | 28 +++++- - arch/mips/bcm63xx/dev-flash.c | 1 + - arch/mips/bcm63xx/dev-spi.c | 6 +- - arch/mips/bcm63xx/dev-uart.c | 3 +- - arch/mips/bcm63xx/irq.c | 19 ++++ - arch/mips/bcm63xx/prom.c | 4 +- - arch/mips/bcm63xx/reset.c | 29 +++++- - arch/mips/bcm63xx/setup.c | 3 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 110 +++++++++++++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h | 1 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 45 ++++++++- - arch/mips/include/asm/mach-bcm63xx/ioremap.h | 4 + - arch/mips/pci/pci-bcm63xx.c | 3 +- - 15 files changed, 259 insertions(+), 19 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -1,6 +1,10 @@ - menu "CPU support" - depends on BCM63XX - -+config BCM63XX_CPU_3368 -+ bool "support 3368 CPU" -+ select HW_HAS_PCI -+ - config BCM63XX_CPU_6328 - bool "support 6328 CPU" - select HW_HAS_PCI ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -84,7 +84,7 @@ static void enetx_set(struct clk *clk, i - else - clk_disable_unlocked(&clk_enet_misc); - -- if (BCMCPU_IS_6358()) { -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) { - u32 mask; - - if (clk->id == 0) -@@ -110,9 +110,8 @@ static struct clk clk_enet1 = { - */ - static void ephy_set(struct clk *clk, int enable) - { -- if (!BCMCPU_IS_6358()) -- return; -- bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable); -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) -+ bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable); - } - - -@@ -155,9 +154,10 @@ static struct clk clk_enetsw = { - */ - static void pcm_set(struct clk *clk, int enable) - { -- if (!BCMCPU_IS_6358()) -- return; -- bcm_hwclock_set(CKCTL_6358_PCM_EN, enable); -+ if (BCMCPU_IS_3368()) -+ bcm_hwclock_set(CKCTL_3368_PCM_EN, enable); -+ if (BCMCPU_IS_6358()) -+ bcm_hwclock_set(CKCTL_6358_PCM_EN, enable); - } - - static struct clk clk_pcm = { -@@ -211,7 +211,7 @@ static void spi_set(struct clk *clk, int - mask = CKCTL_6338_SPI_EN; - else if (BCMCPU_IS_6348()) - mask = CKCTL_6348_SPI_EN; -- else if (BCMCPU_IS_6358()) -+ else if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) - mask = CKCTL_6358_SPI_EN; - else if (BCMCPU_IS_6362()) - mask = CKCTL_6362_SPI_EN; -@@ -338,7 +338,7 @@ struct clk *clk_get(struct device *dev, - return &clk_xtm; - if (!strcmp(id, "periph")) - return &clk_periph; -- if (BCMCPU_IS_6358() && !strcmp(id, "pcm")) -+ if ((BCMCPU_IS_3368() || BCMCPU_IS_6358()) && !strcmp(id, "pcm")) - return &clk_pcm; - if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec")) - return &clk_ipsec; ---- a/arch/mips/bcm63xx/cpu.c -+++ b/arch/mips/bcm63xx/cpu.c -@@ -29,6 +29,14 @@ static u8 bcm63xx_cpu_rev; - static unsigned int bcm63xx_cpu_freq; - static unsigned int bcm63xx_memory_size; - -+static const unsigned long bcm3368_regs_base[] = { -+ __GEN_CPU_REGS_TABLE(3368) -+}; -+ -+static const int bcm3368_irqs[] = { -+ __GEN_CPU_IRQ_TABLE(3368) -+}; -+ - static const unsigned long bcm6328_regs_base[] = { - __GEN_CPU_REGS_TABLE(6328) - }; -@@ -116,6 +124,9 @@ unsigned int bcm63xx_get_memory_size(voi - static unsigned int detect_cpu_clock(void) - { - switch (bcm63xx_get_cpu_id()) { -+ case BCM3368_CPU_ID: -+ return 300000000; -+ - case BCM6328_CPU_ID: - { - unsigned int tmp, mips_pll_fcvo; -@@ -266,7 +277,7 @@ static unsigned int detect_memory_size(v - banks = (val & SDRAM_CFG_BANK_MASK) ? 2 : 1; - } - -- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) { -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) { - val = bcm_memc_readl(MEMC_CFG_REG); - rows = (val & MEMC_CFG_ROW_MASK) >> MEMC_CFG_ROW_SHIFT; - cols = (val & MEMC_CFG_COL_MASK) >> MEMC_CFG_COL_SHIFT; -@@ -302,10 +313,17 @@ void __init bcm63xx_cpu_init(void) - chipid_reg = BCM_6345_PERF_BASE; - break; - case CPU_BMIPS4350: -- if ((read_c0_prid() & 0xf0) == 0x10) -+ switch ((read_c0_prid() & 0xff)) { -+ case 0x04: -+ chipid_reg = BCM_3368_PERF_BASE; -+ break; -+ case 0x10: - chipid_reg = BCM_6345_PERF_BASE; -- else -+ break; -+ default: - chipid_reg = BCM_6368_PERF_BASE; -+ break; -+ } - break; - } - -@@ -322,6 +340,10 @@ void __init bcm63xx_cpu_init(void) - bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT; - - switch (bcm63xx_cpu_id) { -+ case BCM3368_CPU_ID: -+ bcm63xx_regs_base = bcm3368_regs_base; -+ bcm63xx_irqs = bcm3368_irqs; -+ break; - case BCM6328_CPU_ID: - bcm63xx_regs_base = bcm6328_regs_base; - bcm63xx_irqs = bcm6328_irqs; ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -71,6 +71,7 @@ static int __init bcm63xx_detect_flash_t - case BCM6348_CPU_ID: - /* no way to auto detect so assume parallel */ - return BCM63XX_FLASH_TYPE_PARALLEL; -+ case BCM3368_CPU_ID: - case BCM6358_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL) ---- a/arch/mips/bcm63xx/dev-spi.c -+++ b/arch/mips/bcm63xx/dev-spi.c -@@ -37,7 +37,8 @@ static __init void bcm63xx_spi_regs_init - { - if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) - bcm63xx_regs_spi = bcm6348_regs_spi; -- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || -+ BCMCPU_IS_6362() || BCMCPU_IS_6368()) - bcm63xx_regs_spi = bcm6358_regs_spi; - } - #else -@@ -87,7 +88,8 @@ int __init bcm63xx_spi_register(void) - spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH; - } - -- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() || -+ BCMCPU_IS_6368()) { - spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1; - spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE; - spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT; ---- a/arch/mips/bcm63xx/dev-uart.c -+++ b/arch/mips/bcm63xx/dev-uart.c -@@ -54,7 +54,8 @@ int __init bcm63xx_uart_register(unsigne - if (id >= ARRAY_SIZE(bcm63xx_uart_devices)) - return -ENODEV; - -- if (id == 1 && (!BCMCPU_IS_6358() && !BCMCPU_IS_6368())) -+ if (id == 1 && (!BCMCPU_IS_3368() && !BCMCPU_IS_6358() && -+ !BCMCPU_IS_6368())) - return -ENODEV; - - if (id == 0) { ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -27,6 +27,17 @@ static void __internal_irq_unmask_32(uns - static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused; - - #ifndef BCMCPU_RUNTIME_DETECT -+#ifdef CONFIG_BCM63XX_CPU_3368 -+#define irq_stat_reg PERF_IRQSTAT_3368_REG -+#define irq_mask_reg PERF_IRQMASK_3368_REG -+#define irq_bits 32 -+#define is_ext_irq_cascaded 0 -+#define ext_irq_start 0 -+#define ext_irq_end 0 -+#define ext_irq_count 4 -+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_3368 -+#define ext_irq_cfg_reg2 0 -+#endif - #ifdef CONFIG_BCM63XX_CPU_6328 - #define irq_stat_reg PERF_IRQSTAT_6328_REG - #define irq_mask_reg PERF_IRQMASK_6328_REG -@@ -140,6 +151,13 @@ static void bcm63xx_init_irq(void) - irq_mask_addr = bcm63xx_regset_address(RSET_PERF); - - switch (bcm63xx_get_cpu_id()) { -+ case BCM3368_CPU_ID: -+ irq_stat_addr += PERF_IRQSTAT_3368_REG; -+ irq_mask_addr += PERF_IRQMASK_3368_REG; -+ irq_bits = 32; -+ ext_irq_count = 4; -+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368; -+ break; - case BCM6328_CPU_ID: - irq_stat_addr += PERF_IRQSTAT_6328_REG; - irq_mask_addr += PERF_IRQMASK_6328_REG; -@@ -479,6 +497,7 @@ static int bcm63xx_external_irq_set_type - reg &= ~EXTIRQ_CFG_BOTHEDGE_6348(irq); - break; - -+ case BCM3368_CPU_ID: - case BCM6328_CPU_ID: - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -26,7 +26,9 @@ void __init prom_init(void) - bcm_wdt_writel(WDT_STOP_2, WDT_CTL_REG); - - /* disable all hardware blocks clock for now */ -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_3368()) -+ mask = CKCTL_3368_ALL_SAFE_EN; -+ else if (BCMCPU_IS_6328()) - mask = CKCTL_6328_ALL_SAFE_EN; - else if (BCMCPU_IS_6338()) - mask = CKCTL_6338_ALL_SAFE_EN; ---- a/arch/mips/bcm63xx/reset.c -+++ b/arch/mips/bcm63xx/reset.c -@@ -30,6 +30,19 @@ - [BCM63XX_RESET_PCIE] = BCM## __cpu ##_RESET_PCIE, \ - [BCM63XX_RESET_PCIE_EXT] = BCM## __cpu ##_RESET_PCIE_EXT, - -+#define BCM3368_RESET_SPI SOFTRESET_3368_SPI_MASK -+#define BCM3368_RESET_ENET SOFTRESET_3368_ENET_MASK -+#define BCM3368_RESET_USBH 0 -+#define BCM3368_RESET_USBD SOFTRESET_3368_USBS_MASK -+#define BCM3368_RESET_DSL 0 -+#define BCM3368_RESET_SAR 0 -+#define BCM3368_RESET_EPHY SOFTRESET_3368_EPHY_MASK -+#define BCM3368_RESET_ENETSW 0 -+#define BCM3368_RESET_PCM SOFTRESET_3368_PCM_MASK -+#define BCM3368_RESET_MPI SOFTRESET_3368_MPI_MASK -+#define BCM3368_RESET_PCIE 0 -+#define BCM3368_RESET_PCIE_EXT 0 -+ - #define BCM6328_RESET_SPI SOFTRESET_6328_SPI_MASK - #define BCM6328_RESET_ENET 0 - #define BCM6328_RESET_USBH SOFTRESET_6328_USBH_MASK -@@ -117,6 +130,10 @@ - /* - * core reset bits - */ -+static const u32 bcm3368_reset_bits[] = { -+ __GEN_RESET_BITS_TABLE(3368) -+}; -+ - static const u32 bcm6328_reset_bits[] = { - __GEN_RESET_BITS_TABLE(6328) - }; -@@ -146,7 +163,10 @@ static int reset_reg; - - static int __init bcm63xx_reset_bits_init(void) - { -- if (BCMCPU_IS_6328()) { -+ if (BCMCPU_IS_3368()) { -+ reset_reg = PERF_SOFTRESET_6358_REG; -+ bcm63xx_reset_bits = bcm3368_reset_bits; -+ } else if (BCMCPU_IS_6328()) { - reset_reg = PERF_SOFTRESET_6328_REG; - bcm63xx_reset_bits = bcm6328_reset_bits; - } else if (BCMCPU_IS_6338()) { -@@ -170,6 +190,13 @@ static int __init bcm63xx_reset_bits_ini - } - #else - -+#ifdef CONFIG_BCM63XX_CPU_3368 -+static const u32 bcm63xx_reset_bits[] = { -+ __GEN_RESET_BITS_TABLE(3368) -+}; -+#define reset_reg PERF_SOFTRESET_6358_REG -+#endif -+ - #ifdef CONFIG_BCM63XX_CPU_6328 - static const u32 bcm63xx_reset_bits[] = { - __GEN_RESET_BITS_TABLE(6328) ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -68,6 +68,9 @@ void bcm63xx_machine_reboot(void) - - /* mask and clear all external irq */ - switch (bcm63xx_get_cpu_id()) { -+ case BCM3368_CPU_ID: -+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_3368; -+ break; - case BCM6328_CPU_ID: - perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328; - break; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -9,6 +9,7 @@ - * compile time if only one CPU support is enabled (idea stolen from - * arm mach-types) - */ -+#define BCM3368_CPU_ID 0x3368 - #define BCM6328_CPU_ID 0x6328 - #define BCM6338_CPU_ID 0x6338 - #define BCM6345_CPU_ID 0x6345 -@@ -22,6 +23,19 @@ u16 __bcm63xx_get_cpu_id(void); - u8 bcm63xx_get_cpu_rev(void); - unsigned int bcm63xx_get_cpu_freq(void); - -+#ifdef CONFIG_BCM63XX_CPU_3368 -+# ifdef bcm63xx_get_cpu_id -+# undef bcm63xx_get_cpu_id -+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id() -+# define BCMCPU_RUNTIME_DETECT -+# else -+# define bcm63xx_get_cpu_id() BCM3368_CPU_ID -+# endif -+# define BCMCPU_IS_3368() (bcm63xx_get_cpu_id() == BCM3368_CPU_ID) -+#else -+# define BCMCPU_IS_3368() (0) -+#endif -+ - #ifdef CONFIG_BCM63XX_CPU_6328 - # ifdef bcm63xx_get_cpu_id - # undef bcm63xx_get_cpu_id -@@ -191,6 +205,53 @@ enum bcm63xx_regs_set { - #define RSET_RNG_SIZE 20 - - /* -+ * 3368 register sets base address -+ */ -+#define BCM_3368_DSL_LMEM_BASE (0xdeadbeef) -+#define BCM_3368_PERF_BASE (0xfff8c000) -+#define BCM_3368_TIMER_BASE (0xfff8c040) -+#define BCM_3368_WDT_BASE (0xfff8c080) -+#define BCM_3368_UART0_BASE (0xfff8c100) -+#define BCM_3368_UART1_BASE (0xfff8c120) -+#define BCM_3368_GPIO_BASE (0xfff8c080) -+#define BCM_3368_SPI_BASE (0xfff8c800) -+#define BCM_3368_HSSPI_BASE (0xdeadbeef) -+#define BCM_3368_UDC0_BASE (0xdeadbeef) -+#define BCM_3368_USBDMA_BASE (0xdeadbeef) -+#define BCM_3368_OHCI0_BASE (0xdeadbeef) -+#define BCM_3368_OHCI_PRIV_BASE (0xdeadbeef) -+#define BCM_3368_USBH_PRIV_BASE (0xdeadbeef) -+#define BCM_3368_USBD_BASE (0xdeadbeef) -+#define BCM_3368_MPI_BASE (0xfff80000) -+#define BCM_3368_PCMCIA_BASE (0xfff80054) -+#define BCM_3368_PCIE_BASE (0xdeadbeef) -+#define BCM_3368_SDRAM_REGS_BASE (0xdeadbeef) -+#define BCM_3368_DSL_BASE (0xdeadbeef) -+#define BCM_3368_UBUS_BASE (0xdeadbeef) -+#define BCM_3368_ENET0_BASE (0xfff98000) -+#define BCM_3368_ENET1_BASE (0xfff98800) -+#define BCM_3368_ENETDMA_BASE (0xfff99800) -+#define BCM_3368_ENETDMAC_BASE (0xfff99900) -+#define BCM_3368_ENETDMAS_BASE (0xfff99a00) -+#define BCM_3368_ENETSW_BASE (0xdeadbeef) -+#define BCM_3368_EHCI0_BASE (0xdeadbeef) -+#define BCM_3368_SDRAM_BASE (0xdeadbeef) -+#define BCM_3368_MEMC_BASE (0xfff84000) -+#define BCM_3368_DDR_BASE (0xdeadbeef) -+#define BCM_3368_M2M_BASE (0xdeadbeef) -+#define BCM_3368_ATM_BASE (0xdeadbeef) -+#define BCM_3368_XTM_BASE (0xdeadbeef) -+#define BCM_3368_XTMDMA_BASE (0xdeadbeef) -+#define BCM_3368_XTMDMAC_BASE (0xdeadbeef) -+#define BCM_3368_XTMDMAS_BASE (0xdeadbeef) -+#define BCM_3368_PCM_BASE (0xfff9c200) -+#define BCM_3368_PCMDMA_BASE (0xdeadbeef) -+#define BCM_3368_PCMDMAC_BASE (0xdeadbeef) -+#define BCM_3368_PCMDMAS_BASE (0xdeadbeef) -+#define BCM_3368_RNG_BASE (0xdeadbeef) -+#define BCM_3368_MISC_BASE (0xdeadbeef) -+ -+/* - * 6328 register sets base address - */ - #define BCM_6328_DSL_LMEM_BASE (0xdeadbeef) -@@ -620,6 +681,9 @@ static inline unsigned long bcm63xx_regs - #ifdef BCMCPU_RUNTIME_DETECT - return bcm63xx_regs_base[set]; - #else -+#ifdef CONFIG_BCM63XX_CPU_3368 -+ __GEN_RSET(3368) -+#endif - #ifdef CONFIG_BCM63XX_CPU_6328 - __GEN_RSET(6328) - #endif -@@ -687,6 +751,52 @@ enum bcm63xx_irq { - }; - - /* -+ * 3368 irqs -+ */ -+#define BCM_3368_TIMER_IRQ (IRQ_INTERNAL_BASE + 0) -+#define BCM_3368_SPI_IRQ (IRQ_INTERNAL_BASE + 1) -+#define BCM_3368_UART0_IRQ (IRQ_INTERNAL_BASE + 2) -+#define BCM_3368_UART1_IRQ (IRQ_INTERNAL_BASE + 3) -+#define BCM_3368_DSL_IRQ 0 -+#define BCM_3368_UDC0_IRQ 0 -+#define BCM_3368_OHCI0_IRQ 0 -+#define BCM_3368_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) -+#define BCM_3368_ENET1_IRQ (IRQ_INTERNAL_BASE + 6) -+#define BCM_3368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_3368_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 15) -+#define BCM_3368_ENET0_TXDMA_IRQ (IRQ_INTERNAL_BASE + 16) -+#define BCM_3368_HSSPI_IRQ 0 -+#define BCM_3368_EHCI0_IRQ 0 -+#define BCM_3368_USBD_IRQ 0 -+#define BCM_3368_USBD_RXDMA0_IRQ 0 -+#define BCM_3368_USBD_TXDMA0_IRQ 0 -+#define BCM_3368_USBD_RXDMA1_IRQ 0 -+#define BCM_3368_USBD_TXDMA1_IRQ 0 -+#define BCM_3368_USBD_RXDMA2_IRQ 0 -+#define BCM_3368_USBD_TXDMA2_IRQ 0 -+#define BCM_3368_ENET1_RXDMA_IRQ (IRQ_INTERNAL_BASE + 17) -+#define BCM_3368_ENET1_TXDMA_IRQ (IRQ_INTERNAL_BASE + 18) -+#define BCM_3368_PCI_IRQ (IRQ_INTERNAL_BASE + 31) -+#define BCM_3368_PCMCIA_IRQ 0 -+#define BCM_3368_ATM_IRQ 0 -+#define BCM_3368_ENETSW_RXDMA0_IRQ 0 -+#define BCM_3368_ENETSW_RXDMA1_IRQ 0 -+#define BCM_3368_ENETSW_RXDMA2_IRQ 0 -+#define BCM_3368_ENETSW_RXDMA3_IRQ 0 -+#define BCM_3368_ENETSW_TXDMA0_IRQ 0 -+#define BCM_3368_ENETSW_TXDMA1_IRQ 0 -+#define BCM_3368_ENETSW_TXDMA2_IRQ 0 -+#define BCM_3368_ENETSW_TXDMA3_IRQ 0 -+#define BCM_3368_XTM_IRQ 0 -+#define BCM_3368_XTM_DMA0_IRQ 0 -+ -+#define BCM_3368_EXT_IRQ0 (IRQ_INTERNAL_BASE + 25) -+#define BCM_3368_EXT_IRQ1 (IRQ_INTERNAL_BASE + 26) -+#define BCM_3368_EXT_IRQ2 (IRQ_INTERNAL_BASE + 27) -+#define BCM_3368_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28) -+ -+ -+/* - * 6328 irqs - */ - #define BCM_6328_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -@@ -11,6 +11,7 @@ static inline unsigned long bcm63xx_gpio - switch (bcm63xx_get_cpu_id()) { - case BCM6328_CPU_ID: - return 32; -+ case BCM3368_CPU_ID: - case BCM6358_CPU_ID: - return 40; - case BCM6338_CPU_ID: ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -15,6 +15,39 @@ - /* Clock Control register */ - #define PERF_CKCTL_REG 0x4 - -+#define CKCTL_3368_MAC_EN (1 << 3) -+#define CKCTL_3368_TC_EN (1 << 5) -+#define CKCTL_3368_US_TOP_EN (1 << 6) -+#define CKCTL_3368_DS_TOP_EN (1 << 7) -+#define CKCTL_3368_APM_EN (1 << 8) -+#define CKCTL_3368_SPI_EN (1 << 9) -+#define CKCTL_3368_USBS_EN (1 << 10) -+#define CKCTL_3368_BMU_EN (1 << 11) -+#define CKCTL_3368_PCM_EN (1 << 12) -+#define CKCTL_3368_NTP_EN (1 << 13) -+#define CKCTL_3368_ACP_B_EN (1 << 14) -+#define CKCTL_3368_ACP_A_EN (1 << 15) -+#define CKCTL_3368_EMUSB_EN (1 << 17) -+#define CKCTL_3368_ENET0_EN (1 << 18) -+#define CKCTL_3368_ENET1_EN (1 << 19) -+#define CKCTL_3368_USBU_EN (1 << 20) -+#define CKCTL_3368_EPHY_EN (1 << 21) -+ -+#define CKCTL_3368_ALL_SAFE_EN (CKCTL_3368_MAC_EN | \ -+ CKCTL_3368_TC_EN | \ -+ CKCTL_3368_US_TOP_EN | \ -+ CKCTL_3368_DS_TOP_EN | \ -+ CKCTL_3368_APM_EN | \ -+ CKCTL_3368_SPI_EN | \ -+ CKCTL_3368_USBS_EN | \ -+ CKCTL_3368_BMU_EN | \ -+ CKCTL_3368_PCM_EN | \ -+ CKCTL_3368_NTP_EN | \ -+ CKCTL_3368_ACP_B_EN | \ -+ CKCTL_3368_ACP_A_EN | \ -+ CKCTL_3368_EMUSB_EN | \ -+ CKCTL_3368_USBU_EN) -+ - #define CKCTL_6328_PHYMIPS_EN (1 << 0) - #define CKCTL_6328_ADSL_QPROC_EN (1 << 1) - #define CKCTL_6328_ADSL_AFE_EN (1 << 2) -@@ -181,6 +214,7 @@ - #define SYS_PLL_SOFT_RESET 0x1 - - /* Interrupt Mask register */ -+#define PERF_IRQMASK_3368_REG 0xc - #define PERF_IRQMASK_6328_REG 0x20 - #define PERF_IRQMASK_6338_REG 0xc - #define PERF_IRQMASK_6345_REG 0xc -@@ -190,6 +224,7 @@ - #define PERF_IRQMASK_6368_REG 0x20 - - /* Interrupt Status register */ -+#define PERF_IRQSTAT_3368_REG 0x10 - #define PERF_IRQSTAT_6328_REG 0x28 - #define PERF_IRQSTAT_6338_REG 0x10 - #define PERF_IRQSTAT_6345_REG 0x10 -@@ -199,6 +234,7 @@ - #define PERF_IRQSTAT_6368_REG 0x28 - - /* External Interrupt Configuration register */ -+#define PERF_EXTIRQ_CFG_REG_3368 0x14 - #define PERF_EXTIRQ_CFG_REG_6328 0x18 - #define PERF_EXTIRQ_CFG_REG_6338 0x14 - #define PERF_EXTIRQ_CFG_REG_6345 0x14 -@@ -236,6 +272,13 @@ - #define PERF_SOFTRESET_6362_REG 0x10 - #define PERF_SOFTRESET_6368_REG 0x10 - -+#define SOFTRESET_3368_SPI_MASK (1 << 0) -+#define SOFTRESET_3368_ENET_MASK (1 << 2) -+#define SOFTRESET_3368_MPI_MASK (1 << 3) -+#define SOFTRESET_3368_EPHY_MASK (1 << 6) -+#define SOFTRESET_3368_USBS_MASK (1 << 11) -+#define SOFTRESET_3368_PCM_MASK (1 << 13) -+ - #define SOFTRESET_6328_SPI_MASK (1 << 0) - #define SOFTRESET_6328_EPHY_MASK (1 << 1) - #define SOFTRESET_6328_SAR_MASK (1 << 2) -@@ -1293,7 +1336,7 @@ - #define SPI_6348_RX_DATA 0x80 - #define SPI_6348_RX_DATA_SIZE 0x3f - --/* BCM 6358/6262/6368 SPI core */ -+/* BCM 3368/6358/6262/6368 SPI core */ - #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */ - #define SPI_6358_MSG_CTL_WIDTH 16 - #define SPI_6358_MSG_DATA 0x02 ---- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h -+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h -@@ -11,6 +11,10 @@ static inline phys_t fixup_bigphys_addr( - static inline int is_bcm63xx_internal_registers(phys_t offset) - { - switch (bcm63xx_get_cpu_id()) { -+ case BCM3368_CPU_ID: -+ if (offset >= 0xfff80000) -+ return 1; -+ break; - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: - case BCM6348_CPU_ID: ---- a/arch/mips/pci/pci-bcm63xx.c -+++ b/arch/mips/pci/pci-bcm63xx.c -@@ -266,7 +266,7 @@ static int __init bcm63xx_register_pci(v - /* setup PCI to local bus access, used by PCI device to target - * local RAM while bus mastering */ - bcm63xx_int_cfg_writel(0, PCI_BASE_ADDRESS_3); -- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) -+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) - val = MPI_SP0_REMAP_ENABLE_MASK; - else - val = 0; -@@ -338,6 +338,7 @@ static int __init bcm63xx_pci_init(void) - case BCM6328_CPU_ID: - case BCM6362_CPU_ID: - return bcm63xx_register_pcie(); -+ case BCM3368_CPU_ID: - case BCM6348_CPU_ID: - case BCM6358_CPU_ID: - case BCM6368_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.9/037-MIPS-BCM63XX-recognize-Cable-Modem-firmware-format.patch b/target/linux/brcm63xx/patches-3.9/037-MIPS-BCM63XX-recognize-Cable-Modem-firmware-format.patch deleted file mode 100644 index 83e8b92a02..0000000000 --- a/target/linux/brcm63xx/patches-3.9/037-MIPS-BCM63XX-recognize-Cable-Modem-firmware-format.patch +++ /dev/null @@ -1,101 +0,0 @@ -From f3b3faafe7b5a1c07b12d18e96c36bc8a0eecaed Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:41 +0000 -Subject: [PATCH 3/6] MIPS: BCM63XX: recognize Cable Modem firmware format - -Add the firmware header format which is used by Broadcom Cable Modem -SoCs such as the BCM3368 SoC. We export the bcm_hcs firmware format -structure because it is used by user-land tools to create firmware -images for these SoCs and will later be used by a corresponding MTD -parser. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Patchwork: https://patchwork.linux-mips.org/patch/5496/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 14 ++++++++++++-- - include/uapi/linux/Kbuild | 1 + - include/uapi/linux/bcm933xx_hcs.h | 24 ++++++++++++++++++++++++ - 3 files changed, 37 insertions(+), 2 deletions(-) - create mode 100644 include/uapi/linux/bcm933xx_hcs.h - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -28,8 +28,12 @@ - #include - #include - -+#include -+ - #define PFX "board_bcm963xx: " - -+#define HCS_OFFSET_128K 0x20000 -+ - static struct board_info board; - - /* -@@ -722,8 +726,9 @@ void __init board_prom_init(void) - unsigned int i; - u8 *boot_addr, *cfe; - char cfe_version[32]; -- char *board_name; -+ char *board_name = NULL; - u32 val; -+ struct bcm_hcs *hcs; - - /* read base address of boot chip select (0) - * 6328/6362 do not have MPI but boot from a fixed address -@@ -747,7 +752,12 @@ void __init board_prom_init(void) - - bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET); - -- board_name = bcm63xx_nvram_get_name(); -+ if (BCMCPU_IS_3368()) { -+ hcs = (struct bcm_hcs *)boot_addr; -+ board_name = hcs->filename; -+ } else { -+ board_name = bcm63xx_nvram_get_name(); -+ } - /* find board by name */ - for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) { - if (strncmp(board_name, bcm963xx_boards[i]->name, 16)) ---- a/include/uapi/linux/Kbuild -+++ b/include/uapi/linux/Kbuild -@@ -62,6 +62,7 @@ header-y += auxvec.h - header-y += ax25.h - header-y += b1lli.h - header-y += baycom.h -+header-y += bcm933xx_hcs.h - header-y += bfs_fs.h - header-y += binfmts.h - header-y += blkpg.h ---- /dev/null -+++ b/include/uapi/linux/bcm933xx_hcs.h -@@ -0,0 +1,24 @@ -+/* -+ * Broadcom Cable Modem firmware format -+ */ -+ -+#ifndef __BCM933XX_HCS_H -+#define __BCM933XX_HCS_H -+ -+#include -+ -+struct bcm_hcs { -+ __u16 magic; -+ __u16 control; -+ __u16 rev_maj; -+ __u16 rev_min; -+ __u32 build_date; -+ __u32 filelen; -+ __u32 ldaddress; -+ char filename[64]; -+ __u16 hcs; -+ __u16 her_znaet_chto; -+ __u32 crc; -+}; -+ -+#endif /* __BCM933XX_HCS */ diff --git a/target/linux/brcm63xx/patches-3.9/038-MIPS-BCM63XX-provide-a-MAC-address-for-BCM3368-chips.patch b/target/linux/brcm63xx/patches-3.9/038-MIPS-BCM63XX-provide-a-MAC-address-for-BCM3368-chips.patch deleted file mode 100644 index ad32ac1738..0000000000 --- a/target/linux/brcm63xx/patches-3.9/038-MIPS-BCM63XX-provide-a-MAC-address-for-BCM3368-chips.patch +++ /dev/null @@ -1,46 +0,0 @@ -From 404fdc457082772ff52e22988e09e82c0d6e8780 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:42 +0000 -Subject: [PATCH 4/6] MIPS: BCM63XX: provide a MAC address for BCM3368 chips - -The BCM3368 SoC uses a NVRAM format which is not compatible with the one -used by CFE, provide a default MAC address which is suitable for use and -which is the default one also being used by the bootloader on these -chips. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Patchwork: https://patchwork.linux-mips.org/patch/5498/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/nvram.c | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/arch/mips/bcm63xx/nvram.c -+++ b/arch/mips/bcm63xx/nvram.c -@@ -45,6 +45,7 @@ void __init bcm63xx_nvram_init(void *add - { - unsigned int check_len; - u32 crc, expected_crc; -+ u8 hcs_mac_addr[ETH_ALEN] = { 0x00, 0x10, 0x18, 0xff, 0xff, 0xff }; - - /* extract nvram data */ - memcpy(&nvram, addr, sizeof(nvram)); -@@ -65,6 +66,15 @@ void __init bcm63xx_nvram_init(void *add - if (crc != expected_crc) - pr_warn("nvram checksum failed, contents may be invalid (expected %08x, got %08x)\n", - expected_crc, crc); -+ -+ /* Cable modems have a different NVRAM which is embedded in the eCos -+ * firmware and not easily extractible, give at least a MAC address -+ * pool. -+ */ -+ if (BCMCPU_IS_3368()) { -+ memcpy(nvram.mac_addr_base, hcs_mac_addr, ETH_ALEN); -+ nvram.mac_addr_count = 2; -+ } - } - - u8 *bcm63xx_nvram_get_name(void) diff --git a/target/linux/brcm63xx/patches-3.9/039-MIPS-BCM63XX-let-board-specify-an-external-GPIO-to-r.patch b/target/linux/brcm63xx/patches-3.9/039-MIPS-BCM63XX-let-board-specify-an-external-GPIO-to-r.patch deleted file mode 100644 index 122d915943..0000000000 --- a/target/linux/brcm63xx/patches-3.9/039-MIPS-BCM63XX-let-board-specify-an-external-GPIO-to-r.patch +++ /dev/null @@ -1,49 +0,0 @@ -From 0a97aafe7fe50ed183e7fa0121fa7838e2e20306 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:43 +0000 -Subject: [PATCH 5/6] MIPS: BCM63XX: let board specify an external GPIO to - reset PHY - -Some boards may need to reset their external PHY or switch they are -attached to, add a hook for doing this along with providing custom -linux/gpio.h flags for doing this. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Cc: Florian Fainelli -Patchwork: https://patchwork.linux-mips.org/patch/5501/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++ - arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 6 ++++++ - 2 files changed, 10 insertions(+) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -883,5 +883,9 @@ int __init board_register_devices(void) - - platform_device_register(&bcm63xx_gpio_leds); - -+ if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags) -+ gpio_request_one(board.ephy_reset_gpio, -+ board.ephy_reset_gpio_flags, "ephy-reset"); -+ - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -45,6 +45,12 @@ struct board_info { - - /* GPIO LEDs */ - struct gpio_led leds[5]; -+ -+ /* External PHY reset GPIO */ -+ unsigned int ephy_reset_gpio; -+ -+ /* External PHY reset GPIO flags from gpio.h */ -+ unsigned long ephy_reset_gpio_flags; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/040-MIPS-BCM63XX-add-support-for-the-Netgear-CVG834G.patch b/target/linux/brcm63xx/patches-3.9/040-MIPS-BCM63XX-add-support-for-the-Netgear-CVG834G.patch deleted file mode 100644 index 2a589ec6d5..0000000000 --- a/target/linux/brcm63xx/patches-3.9/040-MIPS-BCM63XX-add-support-for-the-Netgear-CVG834G.patch +++ /dev/null @@ -1,70 +0,0 @@ -From 04760855f0d99a1cdc67ae0152d95bcc4525cff5 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:44 +0000 -Subject: [PATCH 6/6] MIPS: BCM63XX: add support for the Netgear CVG834G - -Add support for the Netgear CVG834G and enable the two UARTs, Ethernet -on the first MAC, PCI and the two leds. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Cc: Florian Fainelli -Patchwork: https://patchwork.linux-mips.org/patch/5502/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 35 +++++++++++++++++++++++++++++ - 1 file changed, 35 insertions(+) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -37,6 +37,38 @@ - static struct board_info board; - - /* -+ * known 3368 boards -+ */ -+#ifdef CONFIG_BCM63XX_CPU_3368 -+static struct board_info __initdata board_cvg834g = { -+ .name = "CVG834G_E15R3921", -+ .expected_cpu_id = 0x3368, -+ -+ .has_uart0 = 1, -+ .has_uart1 = 1, -+ -+ .has_enet0 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "CVG834G:green:power", -+ .gpio = 37, -+ .default_trigger= "default-on", -+ }, -+ }, -+ -+ .ephy_reset_gpio = 36, -+ .ephy_reset_gpio_flags = GPIOF_INIT_HIGH, -+}; -+#endif -+ -+/* - * known 6328 boards - */ - #ifdef CONFIG_BCM63XX_CPU_6328 -@@ -643,6 +675,9 @@ static struct board_info __initdata boar - * all boards - */ - static const struct board_info __initconst *bcm963xx_boards[] = { -+#ifdef CONFIG_BCM63XX_CPU_3368 -+ &board_cvg834g, -+#endif - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, - #endif diff --git a/target/linux/brcm63xx/patches-3.9/041-MIPS-BCM63XX-remove-bogus-Kconfig-selects.patch b/target/linux/brcm63xx/patches-3.9/041-MIPS-BCM63XX-remove-bogus-Kconfig-selects.patch deleted file mode 100644 index 029e8f1d02..0000000000 --- a/target/linux/brcm63xx/patches-3.9/041-MIPS-BCM63XX-remove-bogus-Kconfig-selects.patch +++ /dev/null @@ -1,47 +0,0 @@ -From 318883517ebc56e1f9068597e9875f578016e225 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 18 Jun 2013 16:55:38 +0000 -Subject: [PATCH] MIPS: BCM63XX: remove bogus Kconfig selects - -Remove the bogus selects on USB-related symbols for 6345 and 6338, not -only we do not yet support USB on BCM63XX, but they also cause the -following warnings: - -warning: (BCM63XX_CPU_6338 && BCM63XX_CPU_6345) selects -USB_OHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies -(USB_SUPPORT && USB && USB_OHCI_HCD) -warning: (BCM63XX_CPU_6338 && BCM63XX_CPU_6345) selects -USB_OHCI_BIG_ENDIAN_DESC which has unmet direct dependencies -(USB_SUPPORT && USB && USB_OHCI_HCD) -make[4]: Leaving directory `/home/florian/dev/linux' - -Just get rid of these bogus Kconfig selects because neither 6345 nor -6338 actually have built-in USB host controllers. - -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: cernekee@gmail.com -Cc: jogo@openwrt.org -Patchwork: http://patchwork.linux-mips.org/patch/5497/ -Signed-off-by: Ralf Baechle ---- - arch/mips/bcm63xx/Kconfig | 5 ----- - 1 file changed, 5 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -12,14 +12,9 @@ config BCM63XX_CPU_6328 - config BCM63XX_CPU_6338 - bool "support 6338 CPU" - select HW_HAS_PCI -- select USB_ARCH_HAS_OHCI -- select USB_OHCI_BIG_ENDIAN_DESC -- select USB_OHCI_BIG_ENDIAN_MMIO - - config BCM63XX_CPU_6345 - bool "support 6345 CPU" -- select USB_OHCI_BIG_ENDIAN_DESC -- select USB_OHCI_BIG_ENDIAN_MMIO - - config BCM63XX_CPU_6348 - bool "support 6348 CPU" diff --git a/target/linux/brcm63xx/patches-3.9/042-MIPS-BMIPS-support-booting-from-physical-CPU-other-t.patch b/target/linux/brcm63xx/patches-3.9/042-MIPS-BMIPS-support-booting-from-physical-CPU-other-t.patch deleted file mode 100644 index 7d0506f5e8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/042-MIPS-BMIPS-support-booting-from-physical-CPU-other-t.patch +++ /dev/null @@ -1,89 +0,0 @@ -From 672d6bea85c7c9c63c086a9423e6d4e5fc286152 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Wed, 26 Jun 2013 18:11:56 +0000 -Subject: [PATCH] MIPS: BMIPS: support booting from physical CPU other than 0 - -BMIPS43xx CPUs have two hardware threads, and on some SoCs such as 3368, -the bootloader has configured the system to boot from TP1 instead of the -more usual TP0. Create the physical to logical CPU mapping to cope with -that, do not remap the software interrupts to be cross CPUs such that we -do not have to do use the logical CPU mapping further down the code, and -finally, reset the slave TP1 only if booted from TP0. - -Signed-off-by: Jonas Gorski -Signed-off-by: Florian Fainelli -Cc: linux-mips@linux-mips.org -Cc: blogic@openwrt.org -Cc: cernekee@gmail.com -Patchwork: https://patchwork.linux-mips.org/patch/5553/ -Patchwork: https://patchwork.linux-mips.org/patch/5556/ -Signed-off-by: Ralf Baechle ---- - arch/mips/kernel/smp-bmips.c | 29 +++++++++++++++++++++++------ - 1 file changed, 23 insertions(+), 6 deletions(-) - ---- a/arch/mips/kernel/smp-bmips.c -+++ b/arch/mips/kernel/smp-bmips.c -@@ -63,7 +63,7 @@ static irqreturn_t bmips_ipi_interrupt(i - - static void __init bmips_smp_setup(void) - { -- int i; -+ int i, cpu = 1, boot_cpu = 0; - - #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) - /* arbitration priority */ -@@ -72,13 +72,22 @@ static void __init bmips_smp_setup(void) - /* NBK and weak order flags */ - set_c0_brcm_config_0(0x30000); - -+ /* Find out if we are running on TP0 or TP1 */ -+ boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31)); -+ - /* - * MIPS interrupts 0,1 (SW INT 0,1) cross over to the other thread - * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output - * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output -+ * -+ * If booting from TP1, leave the existing CMT interrupt routing -+ * such that TP0 responds to SW1 and TP1 responds to SW0. - */ -- change_c0_brcm_cmt_intr(0xf8018000, -- (0x02 << 27) | (0x03 << 15)); -+ if (boot_cpu == 0) -+ change_c0_brcm_cmt_intr(0xf8018000, -+ (0x02 << 27) | (0x03 << 15)); -+ else -+ change_c0_brcm_cmt_intr(0xf8018000, (0x1d << 27)); - - /* single core, 2 threads (2 pipelines) */ - max_cpus = 2; -@@ -106,9 +115,15 @@ static void __init bmips_smp_setup(void) - if (!board_ebase_setup) - board_ebase_setup = &bmips_ebase_setup; - -+ __cpu_number_map[boot_cpu] = 0; -+ __cpu_logical_map[0] = boot_cpu; -+ - for (i = 0; i < max_cpus; i++) { -- __cpu_number_map[i] = 1; -- __cpu_logical_map[i] = 1; -+ if (i != boot_cpu) { -+ __cpu_number_map[i] = cpu; -+ __cpu_logical_map[cpu] = i; -+ cpu++; -+ } - set_cpu_possible(i, 1); - set_cpu_present(i, 1); - } -@@ -157,7 +172,9 @@ static void bmips_boot_secondary(int cpu - bmips_send_ipi_single(cpu, 0); - else { - #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) -- set_c0_brcm_cmt_ctrl(0x01); -+ /* Reset slave TP1 if booting from TP0 */ -+ if (cpu_logical_map(cpu) == 0) -+ set_c0_brcm_cmt_ctrl(0x01); - #elif defined(CONFIG_CPU_BMIPS5000) - if (cpu & 0x01) - write_c0_brcm_action(ACTION_BOOT_THREAD(cpu)); diff --git a/target/linux/brcm63xx/patches-3.9/043-MIPS-BCM63XX-Add-SMP-support-to-prom.c.patch b/target/linux/brcm63xx/patches-3.9/043-MIPS-BCM63XX-Add-SMP-support-to-prom.c.patch deleted file mode 100644 index 23f6d852c8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/043-MIPS-BCM63XX-Add-SMP-support-to-prom.c.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 7c44eabf20cba12049bf9eebfa192afcc2053b2d Mon Sep 17 00:00:00 2001 -From: Kevin Cernekee -Date: Sat, 9 Jul 2011 12:15:06 -0700 -Subject: [PATCH V2 1/2] MIPS: BCM63XX: Add SMP support to prom.c - -This involves two changes to the BSP code: - -1) register_smp_ops() for BMIPS SMP - -2) The CPU1 boot vector on some of the BCM63xx platforms conflicts with -the special interrupt vector (IV). Move it to 0x8000_0380 at boot time, -to resolve the conflict. - -Signed-off-by: Kevin Cernekee -[jogo@openwrt.org: moved SMP ops registration into ifdef guard, - changed ifdef guards to if (IS_ENABLED())] -Signed-off-by: Jonas Gorski ---- -V1 -> V2: - * changed ifdef guards to if (IS_ENABLED()) - - arch/mips/bcm63xx/prom.c | 41 +++++++++++++++++++++++++++++++++++++++++ - 1 file changed, 41 insertions(+) - ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -8,7 +8,11 @@ - - #include - #include -+#include - #include -+#include -+#include -+#include - #include - #include - #include -@@ -54,6 +58,43 @@ void __init prom_init(void) - - /* do low level board init */ - board_prom_init(); -+ -+ if (IS_ENABLED(CONFIG_CPU_BMIPS4350) && IS_ENABLED(CONFIG_SMP)) { -+ /* set up SMP */ -+ register_smp_ops(&bmips_smp_ops); -+ -+ /* -+ * BCM6328 might not have its second CPU enabled, while BCM6358 -+ * needs special handling for its shared TLB, so disable SMP -+ * for now. -+ */ -+ if (BCMCPU_IS_6328()) { -+ bmips_smp_enabled = 0; -+ } else if (BCMCPU_IS_6358()) { -+ bmips_smp_enabled = 0; -+ } -+ -+ if (!bmips_smp_enabled) -+ return; -+ -+ /* -+ * The bootloader has set up the CPU1 reset vector at -+ * 0xa000_0200. -+ * This conflicts with the special interrupt vector (IV). -+ * The bootloader has also set up CPU1 to respond to the wrong -+ * IPI interrupt. -+ * Here we will start up CPU1 in the background and ask it to -+ * reconfigure itself then go back to sleep. -+ */ -+ memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20); -+ __sync(); -+ set_c0_cause(C_SW0); -+ cpumask_set_cpu(1, &bmips_booted_mask); -+ -+ /* -+ * FIXME: we really should have some sort of hazard barrier here -+ */ -+ } - } - - void __init prom_free_prom_memory(void) diff --git a/target/linux/brcm63xx/patches-3.9/044-MIPS-BCM63XX-Enable-second-core-SMP-on-BCM6328-if-av.patch b/target/linux/brcm63xx/patches-3.9/044-MIPS-BCM63XX-Enable-second-core-SMP-on-BCM6328-if-av.patch deleted file mode 100644 index 45a82f52f3..0000000000 --- a/target/linux/brcm63xx/patches-3.9/044-MIPS-BCM63XX-Enable-second-core-SMP-on-BCM6328-if-av.patch +++ /dev/null @@ -1,55 +0,0 @@ -From 41fa6dec9df9b4e55ac522c899270a72e51a9b4b Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 9 Jul 2011 12:15:06 -0700 -Subject: [PATCH V2 2/2] MIPS: BCM63XX: Enable second core SMP on BCM6328 if - available - -BCM6328 has a OTP which tells us if the second core is available. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/prom.c | 6 +++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 2 ++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 7 +++++++ - 3 files changed, 14 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -69,7 +69,11 @@ void __init prom_init(void) - * for now. - */ - if (BCMCPU_IS_6328()) { -- bmips_smp_enabled = 0; -+ reg = bcm_readl(BCM_6328_OTP_BASE + -+ OTP_USER_BITS_6328_REG(3)); -+ -+ if (reg & OTP_6328_REG3_TP1_DISABLED) -+ bmips_smp_enabled = 0; - } else if (BCMCPU_IS_6358()) { - bmips_smp_enabled = 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -296,6 +296,8 @@ enum bcm63xx_regs_set { - #define BCM_6328_PCMDMAS_BASE (0xdeadbeef) - #define BCM_6328_RNG_BASE (0xdeadbeef) - #define BCM_6328_MISC_BASE (0xb0001800) -+#define BCM_6328_OTP_BASE (0xb0000600) -+ - /* - * 6338 register sets base address - */ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1477,4 +1477,11 @@ - - #define PCIE_DEVICE_OFFSET 0x8000 - -+/************************************************************************* -+ * _REG relative to RSET_OTP -+ *************************************************************************/ -+ -+#define OTP_USER_BITS_6328_REG(i) (0x20 + (i) * 4) -+#define OTP_6328_REG3_TP1_DISABLED BIT(9) -+ - #endif /* BCM63XX_REGS_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/045-bcm63xx_enet-implement-reset-autoneg-ethtool-callbac.patch b/target/linux/brcm63xx/patches-3.9/045-bcm63xx_enet-implement-reset-autoneg-ethtool-callbac.patch deleted file mode 100644 index 7c80845b70..0000000000 --- a/target/linux/brcm63xx/patches-3.9/045-bcm63xx_enet-implement-reset-autoneg-ethtool-callbac.patch +++ /dev/null @@ -1,44 +0,0 @@ -From a15c33450df64f183c8ab5de8ef113091081679d Mon Sep 17 00:00:00 2001 -From: Maxime Bizon -Date: Tue, 4 Jun 2013 20:53:33 +0000 -Subject: [PATCH 1/3] bcm63xx_enet: implement reset autoneg ethtool callback - -Implement the rset_nway ethtool callback which uses libphy generic -autonegotiation restart function. - -Signed-off-by: Maxime Bizon ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 15 +++++++++++++++ - 1 file changed, 15 insertions(+) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1330,6 +1330,20 @@ static void bcm_enet_get_ethtool_stats(s - mutex_unlock(&priv->mib_update_lock); - } - -+static int bcm_enet_nway_reset(struct net_device *dev) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ if (priv->has_phy) { -+ if (!priv->phydev) -+ return -ENODEV; -+ return genphy_restart_aneg(priv->phydev); -+ } -+ -+ return -EOPNOTSUPP; -+} -+ - static int bcm_enet_get_settings(struct net_device *dev, - struct ethtool_cmd *cmd) - { -@@ -1472,6 +1486,7 @@ static const struct ethtool_ops bcm_enet - .get_strings = bcm_enet_get_strings, - .get_sset_count = bcm_enet_get_sset_count, - .get_ethtool_stats = bcm_enet_get_ethtool_stats, -+ .nway_reset = bcm_enet_nway_reset, - .get_settings = bcm_enet_get_settings, - .set_settings = bcm_enet_set_settings, - .get_drvinfo = bcm_enet_get_drvinfo, diff --git a/target/linux/brcm63xx/patches-3.9/046-bcm63xx_enet-split-DMA-channel-register-accesses.patch b/target/linux/brcm63xx/patches-3.9/046-bcm63xx_enet-split-DMA-channel-register-accesses.patch deleted file mode 100644 index 9d0c9aac3c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/046-bcm63xx_enet-split-DMA-channel-register-accesses.patch +++ /dev/null @@ -1,346 +0,0 @@ -From 33cab1696444a8e333cf0490bfe04c32d583fd51 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon -Date: Tue, 4 Jun 2013 20:53:34 +0000 -Subject: [PATCH 2/3] bcm63xx_enet: split DMA channel register accesses - -The current bcm63xx_enet driver always uses bcmenet_shared_base whenever -it needs to access DMA channel configuration space or access the DMA -channel state RAM. Split these register in 3 parts to be more accurate: - -- global DMA configuration -- per DMA channel configuration space -- per DMA channel state RAM space - -This is preliminary to support new chips where the global DMA -configuration remains the same, but there is a varying number of DMA -channels located at a different memory offset. - -Signed-off-by: Maxime Bizon -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/dev-enet.c | 23 +++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 4 +- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 139 +++++++++++++--------- - 3 files changed, 105 insertions(+), 61 deletions(-) - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -19,6 +19,16 @@ static struct resource shared_res[] = { - .end = -1, /* filled at runtime */ - .flags = IORESOURCE_MEM, - }, -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, - }; - - static struct platform_device bcm63xx_enet_shared_device = { -@@ -110,10 +120,15 @@ int __init bcm63xx_enet_register(int uni - if (!shared_device_registered) { - shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); - shared_res[0].end = shared_res[0].start; -- if (BCMCPU_IS_6338()) -- shared_res[0].end += (RSET_ENETDMA_SIZE / 2) - 1; -- else -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ -+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -+ shared_res[1].end = shared_res[1].start; -+ shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1; -+ -+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -+ shared_res[2].end = shared_res[2].start; -+ shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1; - - ret = platform_device_register(&bcm63xx_enet_shared_device); - if (ret) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -187,7 +187,9 @@ enum bcm63xx_regs_set { - #define BCM_6358_RSET_SPI_SIZE 1804 - #define BCM_6368_RSET_SPI_SIZE 1804 - #define RSET_ENET_SIZE 2048 --#define RSET_ENETDMA_SIZE 2048 -+#define RSET_ENETDMA_SIZE 256 -+#define RSET_ENETDMAC_SIZE(chans) (16 * (chans)) -+#define RSET_ENETDMAS_SIZE(chans) (16 * (chans)) - #define RSET_ENETSW_SIZE 65536 - #define RSET_UART_SIZE 24 - #define RSET_UDC_SIZE 256 ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -41,8 +41,8 @@ static int copybreak __read_mostly = 128 - module_param(copybreak, int, 0); - MODULE_PARM_DESC(copybreak, "Receive copy threshold"); - --/* io memory shared between all devices */ --static void __iomem *bcm_enet_shared_base; -+/* io registers memory shared between all devices */ -+static void __iomem *bcm_enet_shared_base[3]; - - /* - * io helpers to access mac registers -@@ -63,13 +63,35 @@ static inline void enet_writel(struct bc - */ - static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off) - { -- return bcm_readl(bcm_enet_shared_base + off); -+ return bcm_readl(bcm_enet_shared_base[0] + off); - } - - static inline void enet_dma_writel(struct bcm_enet_priv *priv, - u32 val, u32 off) - { -- bcm_writel(val, bcm_enet_shared_base + off); -+ bcm_writel(val, bcm_enet_shared_base[0] + off); -+} -+ -+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readl(bcm_enet_shared_base[1] + off); -+} -+ -+static inline void enet_dmac_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ bcm_writel(val, bcm_enet_shared_base[1] + off); -+} -+ -+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readl(bcm_enet_shared_base[2] + off); -+} -+ -+static inline void enet_dmas_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ bcm_writel(val, bcm_enet_shared_base[2] + off); - } - - /* -@@ -353,8 +375,8 @@ static int bcm_enet_receive_queue(struct - bcm_enet_refill_rx(dev); - - /* kick rx dma */ -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); - } - - return processed; -@@ -429,10 +451,10 @@ static int bcm_enet_poll(struct napi_str - dev = priv->net_dev; - - /* ack interrupts */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); - - /* reclaim sent skb */ - tx_work_done = bcm_enet_tx_reclaim(dev, 0); -@@ -451,10 +473,10 @@ static int bcm_enet_poll(struct napi_str - napi_complete(napi); - - /* restore rx/tx interrupt */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); - - return rx_work_done; - } -@@ -497,8 +519,8 @@ static irqreturn_t bcm_enet_isr_dma(int - priv = netdev_priv(dev); - - /* mask rx/tx interrupts */ -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - napi_schedule(&priv->napi); - -@@ -557,8 +579,8 @@ static int bcm_enet_start_xmit(struct sk - wmb(); - - /* kick tx dma */ -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->tx_chan)); - - /* stop queue if no more desc available */ - if (!priv->tx_desc_count) -@@ -833,8 +855,8 @@ static int bcm_enet_open(struct net_devi - - /* mask all interrupts and request them */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -@@ -921,28 +943,28 @@ static int bcm_enet_open(struct net_devi - } - - /* write rx & tx ring addresses */ -- enet_dma_writel(priv, priv->rx_desc_dma, -- ENETDMA_RSTART_REG(priv->rx_chan)); -- enet_dma_writel(priv, priv->tx_desc_dma, -- ENETDMA_RSTART_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->tx_chan)); - - /* clear remaining state ram for rx & tx channel */ -- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); - - /* set max rx/tx length */ - enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG); - enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG); - - /* set dma maximum burst len */ -- enet_dma_writel(priv, BCMENET_DMA_MAXBURST, -- ENETDMA_MAXBURST_REG(priv->rx_chan)); -- enet_dma_writel(priv, BCMENET_DMA_MAXBURST, -- ENETDMA_MAXBURST_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->tx_chan)); - - /* set correct transmit fifo watermark */ - enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG); -@@ -960,26 +982,26 @@ static int bcm_enet_open(struct net_devi - val |= ENET_CTL_ENABLE_MASK; - enet_writel(priv, val, ENET_CTL_REG); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); - - /* watch "mib counters about to overflow" interrupt */ - enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); - enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); - - /* watch "packet transferred" interrupt in rx and tx */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); - - if (priv->has_phy) - phy_start(priv->phydev); -@@ -1059,14 +1081,14 @@ static void bcm_enet_disable_dma(struct - { - int limit; - -- enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan)); - - limit = 1000; - do { - u32 val; - -- val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan)); -- if (!(val & ENETDMA_CHANCFG_EN_MASK)) -+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan)); -+ if (!(val & ENETDMAC_CHANCFG_EN_MASK)) - break; - udelay(1); - } while (limit--); -@@ -1092,8 +1114,8 @@ static int bcm_enet_stop(struct net_devi - - /* mask all interrupts */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - /* make sure no mib update is scheduled */ - cancel_work_sync(&priv->mib_update_task); -@@ -1638,7 +1660,7 @@ static int bcm_enet_probe(struct platfor - - /* stop if shared driver failed, assume driver->probe will be - * called in the same order we register devices (correct ?) */ -- if (!bcm_enet_shared_base) -+ if (!bcm_enet_shared_base[0]) - return -ENODEV; - - res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -@@ -1884,14 +1906,19 @@ struct platform_driver bcm63xx_enet_driv - static int bcm_enet_shared_probe(struct platform_device *pdev) - { - struct resource *res; -+ void __iomem *p[3]; -+ unsigned int i; - -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- if (!res) -- return -ENODEV; -+ memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base)); - -- bcm_enet_shared_base = devm_request_and_ioremap(&pdev->dev, res); -- if (!bcm_enet_shared_base) -- return -ENOMEM; -+ for (i = 0; i < 3; i++) { -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ p[i] = devm_ioremap_resource(&pdev->dev, res); -+ if (!p[i]) -+ return -ENOMEM; -+ } -+ -+ memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base)); - - return 0; - } diff --git a/target/linux/brcm63xx/patches-3.9/047-bcm63xx_enet-add-support-for-Broadcom-BCM63xx-integr.patch b/target/linux/brcm63xx/patches-3.9/047-bcm63xx_enet-add-support-for-Broadcom-BCM63xx-integr.patch deleted file mode 100644 index 089acbe79c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/047-bcm63xx_enet-add-support-for-Broadcom-BCM63xx-integr.patch +++ /dev/null @@ -1,1505 +0,0 @@ -From 85b2e40acd7b33409a0d889cd3d0b964c9df4b13 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon -Date: Tue, 4 Jun 2013 20:53:35 +0000 -Subject: [PATCH 3/3] bcm63xx_enet: add support for Broadcom BCM63xx - integrated gigabit switch - -Newer Broadcom BCM63xx SoCs: 6328, 6362 and 6368 have an integrated switch -which needs to be driven slightly differently from the traditional -external switches. This patch introduces changes in arch/mips/bcm63xx in order -to: - -- register a bcm63xx_enetsw driver instead of bcm63xx_enet driver -- update DMA channels configuration & state RAM base addresses -- add a new platform data configuration knob to define the number of - ports per switch/device and force link on some ports -- define the required switch registers - -On the driver side, the following changes are required: - -- the switch ports need to be polled to ensure the link is up and - running and RX/TX can properly work -- basic switch configuration needs to be performed for the switch to - forward packets to the CPU -- update the MIB counters since the integrated - -Signed-off-by: Maxime Bizon -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 + - arch/mips/bcm63xx/dev-enet.c | 113 ++- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 28 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 50 + - .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 + - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 995 +++++++++++++++++++- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 71 ++ - 7 files changed, 1205 insertions(+), 58 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -890,6 +890,10 @@ int __init board_register_devices(void) - !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr)) - bcm63xx_enet_register(1, &board.enet1); - -+ if (board.has_enetsw && -+ !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr)) -+ bcm63xx_enetsw_register(&board.enetsw); -+ - if (board.has_usbd) - bcm63xx_usbd_register(&board.usbd); - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -104,6 +104,64 @@ static struct platform_device bcm63xx_en - }, - }; - -+static struct resource enetsw_res[] = { -+ { -+ /* start & end filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ /* start filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+ { -+ /* start filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct bcm63xx_enetsw_platform_data enetsw_pd; -+ -+static struct platform_device bcm63xx_enetsw_device = { -+ .name = "bcm63xx_enetsw", -+ .num_resources = ARRAY_SIZE(enetsw_res), -+ .resource = enetsw_res, -+ .dev = { -+ .platform_data = &enetsw_pd, -+ }, -+}; -+ -+static int __init register_shared(void) -+{ -+ int ret, chan_count; -+ -+ if (shared_device_registered) -+ return 0; -+ -+ shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); -+ shared_res[0].end = shared_res[0].start; -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) -+ chan_count = 32; -+ else -+ chan_count = 16; -+ -+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -+ shared_res[1].end = shared_res[1].start; -+ shared_res[1].end += RSET_ENETDMAC_SIZE(chan_count) - 1; -+ -+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -+ shared_res[2].end = shared_res[2].start; -+ shared_res[2].end += RSET_ENETDMAS_SIZE(chan_count) - 1; -+ -+ ret = platform_device_register(&bcm63xx_enet_shared_device); -+ if (ret) -+ return ret; -+ shared_device_registered = 1; -+ -+ return 0; -+} -+ - int __init bcm63xx_enet_register(int unit, - const struct bcm63xx_enet_platform_data *pd) - { -@@ -117,24 +175,9 @@ int __init bcm63xx_enet_register(int uni - if (unit == 1 && BCMCPU_IS_6338()) - return -ENODEV; - -- if (!shared_device_registered) { -- shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); -- shared_res[0].end = shared_res[0].start; -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -- -- shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -- shared_res[1].end = shared_res[1].start; -- shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1; -- -- shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -- shared_res[2].end = shared_res[2].start; -- shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1; -- -- ret = platform_device_register(&bcm63xx_enet_shared_device); -- if (ret) -- return ret; -- shared_device_registered = 1; -- } -+ ret = register_shared(); -+ if (ret) -+ return ret; - - if (unit == 0) { - enet0_res[0].start = bcm63xx_regset_address(RSET_ENET0); -@@ -175,3 +218,37 @@ int __init bcm63xx_enet_register(int uni - return ret; - return 0; - } -+ -+int __init -+bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd) -+{ -+ int ret; -+ -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) -+ return -ENODEV; -+ -+ ret = register_shared(); -+ if (ret) -+ return ret; -+ -+ enetsw_res[0].start = bcm63xx_regset_address(RSET_ENETSW); -+ enetsw_res[0].end = enetsw_res[0].start; -+ enetsw_res[0].end += RSET_ENETSW_SIZE - 1; -+ enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0); -+ enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0); -+ if (!enetsw_res[2].start) -+ enetsw_res[2].start = -1; -+ -+ memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof(*pd)); -+ -+ if (BCMCPU_IS_6328()) -+ enetsw_pd.num_ports = ENETSW_PORTS_6328; -+ else if (BCMCPU_IS_6362() || BCMCPU_IS_6368()) -+ enetsw_pd.num_ports = ENETSW_PORTS_6368; -+ -+ ret = platform_device_register(&bcm63xx_enetsw_device); -+ if (ret) -+ return ret; -+ -+ return 0; -+} ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -39,7 +39,35 @@ struct bcm63xx_enet_platform_data { - int phy_id, int reg, int val)); - }; - -+/* -+ * on board ethernet switch platform data -+ */ -+#define ENETSW_MAX_PORT 8 -+#define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */ -+#define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ -+ -+#define ENETSW_RGMII_PORT0 4 -+ -+struct bcm63xx_enetsw_port { -+ int used; -+ int phy_id; -+ -+ int bypass_link; -+ int force_speed; -+ int force_duplex_full; -+ -+ const char *name; -+}; -+ -+struct bcm63xx_enetsw_platform_data { -+ char mac_addr[ETH_ALEN]; -+ int num_ports; -+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+}; -+ - int __init bcm63xx_enet_register(int unit, - const struct bcm63xx_enet_platform_data *pd); - -+int bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd); -+ - #endif /* ! BCM63XX_DEV_ENET_H_ */ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -873,10 +873,60 @@ - * _REG relative to RSET_ENETSW - *************************************************************************/ - -+/* Port traffic control */ -+#define ENETSW_PTCTRL_REG(x) (0x0 + (x)) -+#define ENETSW_PTCTRL_RXDIS_MASK (1 << 0) -+#define ENETSW_PTCTRL_TXDIS_MASK (1 << 1) -+ -+/* Switch mode register */ -+#define ENETSW_SWMODE_REG (0xb) -+#define ENETSW_SWMODE_FWD_EN_MASK (1 << 1) -+ -+/* IMP override Register */ -+#define ENETSW_IMPOV_REG (0xe) -+#define ENETSW_IMPOV_FORCE_MASK (1 << 7) -+#define ENETSW_IMPOV_TXFLOW_MASK (1 << 5) -+#define ENETSW_IMPOV_RXFLOW_MASK (1 << 4) -+#define ENETSW_IMPOV_1000_MASK (1 << 3) -+#define ENETSW_IMPOV_100_MASK (1 << 2) -+#define ENETSW_IMPOV_FDX_MASK (1 << 1) -+#define ENETSW_IMPOV_LINKUP_MASK (1 << 0) -+ -+/* Port override Register */ -+#define ENETSW_PORTOV_REG(x) (0x58 + (x)) -+#define ENETSW_PORTOV_ENABLE_MASK (1 << 6) -+#define ENETSW_PORTOV_TXFLOW_MASK (1 << 5) -+#define ENETSW_PORTOV_RXFLOW_MASK (1 << 4) -+#define ENETSW_PORTOV_1000_MASK (1 << 3) -+#define ENETSW_PORTOV_100_MASK (1 << 2) -+#define ENETSW_PORTOV_FDX_MASK (1 << 1) -+#define ENETSW_PORTOV_LINKUP_MASK (1 << 0) -+ -+/* MDIO control register */ -+#define ENETSW_MDIOC_REG (0xb0) -+#define ENETSW_MDIOC_EXT_MASK (1 << 16) -+#define ENETSW_MDIOC_REG_SHIFT 20 -+#define ENETSW_MDIOC_PHYID_SHIFT 25 -+#define ENETSW_MDIOC_RD_MASK (1 << 30) -+#define ENETSW_MDIOC_WR_MASK (1 << 31) -+ -+/* MDIO data register */ -+#define ENETSW_MDIOD_REG (0xb4) -+ -+/* Global Management Configuration Register */ -+#define ENETSW_GMCR_REG (0x200) -+#define ENETSW_GMCR_RST_MIB_MASK (1 << 0) -+ - /* MIB register */ - #define ENETSW_MIB_REG(x) (0x2800 + (x) * 4) - #define ENETSW_MIB_REG_COUNT 47 - -+/* Jumbo control register port mask register */ -+#define ENETSW_JMBCTL_PORT_REG (0x4004) -+ -+/* Jumbo control mib good frame register */ -+#define ENETSW_JMBCTL_MAXSIZE_REG (0x4008) -+ - - /************************************************************************* - * _REG relative to RSET_OHCI_PRIV ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -24,6 +24,7 @@ struct board_info { - /* enabled feature/device */ - unsigned int has_enet0:1; - unsigned int has_enet1:1; -+ unsigned int has_enetsw:1; - unsigned int has_pci:1; - unsigned int has_pccard:1; - unsigned int has_ohci0:1; -@@ -36,6 +37,7 @@ struct board_info { - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; - struct bcm63xx_enet_platform_data enet1; -+ struct bcm63xx_enetsw_platform_data enetsw; - - /* USB config */ - struct bcm63xx_usbd_platform_data usbd; ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -59,8 +59,43 @@ static inline void enet_writel(struct bc - } - - /* -- * io helpers to access shared registers -+ * io helpers to access switch registers - */ -+static inline u32 enetsw_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readl(priv->base + off); -+} -+ -+static inline void enetsw_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ bcm_writel(val, priv->base + off); -+} -+ -+static inline u16 enetsw_readw(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readw(priv->base + off); -+} -+ -+static inline void enetsw_writew(struct bcm_enet_priv *priv, -+ u16 val, u32 off) -+{ -+ bcm_writew(val, priv->base + off); -+} -+ -+static inline u8 enetsw_readb(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readb(priv->base + off); -+} -+ -+static inline void enetsw_writeb(struct bcm_enet_priv *priv, -+ u8 val, u32 off) -+{ -+ bcm_writeb(val, priv->base + off); -+} -+ -+ -+/* io helpers to access shared registers */ - static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off) - { - return bcm_readl(bcm_enet_shared_base[0] + off); -@@ -218,7 +253,6 @@ static int bcm_enet_refill_rx(struct net - if (!skb) - break; - priv->rx_skb[desc_idx] = skb; -- - p = dma_map_single(&priv->pdev->dev, skb->data, - priv->rx_skb_size, - DMA_FROM_DEVICE); -@@ -321,7 +355,8 @@ static int bcm_enet_receive_queue(struct - } - - /* recycle packet if it's marked as bad */ -- if (unlikely(len_stat & DMADESC_ERR_MASK)) { -+ if (!priv->enet_is_sw && -+ unlikely(len_stat & DMADESC_ERR_MASK)) { - dev->stats.rx_errors++; - - if (len_stat & DMADESC_OVSIZE_MASK) -@@ -552,6 +587,26 @@ static int bcm_enet_start_xmit(struct sk - goto out_unlock; - } - -+ /* pad small packets sent on a switch device */ -+ if (priv->enet_is_sw && skb->len < 64) { -+ int needed = 64 - skb->len; -+ char *data; -+ -+ if (unlikely(skb_tailroom(skb) < needed)) { -+ struct sk_buff *nskb; -+ -+ nskb = skb_copy_expand(skb, 0, needed, GFP_ATOMIC); -+ if (!nskb) { -+ ret = NETDEV_TX_BUSY; -+ goto out_unlock; -+ } -+ dev_kfree_skb(skb); -+ skb = nskb; -+ } -+ data = skb_put(skb, needed); -+ memset(data, 0, needed); -+ } -+ - /* point to the next available desc */ - desc = &priv->tx_desc_cpu[priv->tx_curr_desc]; - priv->tx_skb[priv->tx_curr_desc] = skb; -@@ -961,9 +1016,9 @@ static int bcm_enet_open(struct net_devi - enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG); - - /* set dma maximum burst len */ -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->rx_chan)); -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->tx_chan)); - - /* set correct transmit fifo watermark */ -@@ -1569,7 +1624,7 @@ static int compute_hw_mtu(struct bcm_ene - * it's appended - */ - priv->rx_skb_size = ALIGN(actual_mtu + ETH_FCS_LEN, -- BCMENET_DMA_MAXBURST * 4); -+ priv->dma_maxburst * 4); - return 0; - } - -@@ -1676,6 +1731,9 @@ static int bcm_enet_probe(struct platfor - return -ENOMEM; - priv = netdev_priv(dev); - -+ priv->enet_is_sw = false; -+ priv->dma_maxburst = BCMENET_DMA_MAXBURST; -+ - ret = compute_hw_mtu(priv, dev->mtu); - if (ret) - goto out; -@@ -1901,60 +1959,916 @@ struct platform_driver bcm63xx_enet_driv - }; - - /* -- * reserve & remap memory space shared between all macs -+ * switch mii access callbacks - */ --static int bcm_enet_shared_probe(struct platform_device *pdev) -+static int bcmenet_sw_mdio_read(struct bcm_enet_priv *priv, -+ int ext, int phy_id, int location) - { -- struct resource *res; -- void __iomem *p[3]; -- unsigned int i; -+ u32 reg; -+ int ret; - -- memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base)); -+ spin_lock_bh(&priv->enetsw_mdio_lock); -+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG); - -- for (i = 0; i < 3; i++) { -- res = platform_get_resource(pdev, IORESOURCE_MEM, i); -- p[i] = devm_ioremap_resource(&pdev->dev, res); -- if (!p[i]) -- return -ENOMEM; -- } -+ reg = ENETSW_MDIOC_RD_MASK | -+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) | -+ (location << ENETSW_MDIOC_REG_SHIFT); -+ -+ if (ext) -+ reg |= ENETSW_MDIOC_EXT_MASK; -+ -+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG); -+ udelay(50); -+ ret = enetsw_readw(priv, ENETSW_MDIOD_REG); -+ spin_unlock_bh(&priv->enetsw_mdio_lock); -+ return ret; -+} - -- memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base)); -+static void bcmenet_sw_mdio_write(struct bcm_enet_priv *priv, -+ int ext, int phy_id, int location, -+ uint16_t data) -+{ -+ u32 reg; - -- return 0; -+ spin_lock_bh(&priv->enetsw_mdio_lock); -+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG); -+ -+ reg = ENETSW_MDIOC_WR_MASK | -+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) | -+ (location << ENETSW_MDIOC_REG_SHIFT); -+ -+ if (ext) -+ reg |= ENETSW_MDIOC_EXT_MASK; -+ -+ reg |= data; -+ -+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG); -+ udelay(50); -+ spin_unlock_bh(&priv->enetsw_mdio_lock); - } - --static int bcm_enet_shared_remove(struct platform_device *pdev) -+static inline int bcm_enet_port_is_rgmii(int portid) - { -- return 0; -+ return portid >= ENETSW_RGMII_PORT0; - } - - /* -- * this "shared" driver is needed because both macs share a single -- * address space -+ * enet sw PHY polling - */ --struct platform_driver bcm63xx_enet_shared_driver = { -- .probe = bcm_enet_shared_probe, -- .remove = bcm_enet_shared_remove, -- .driver = { -- .name = "bcm63xx_enet_shared", -- .owner = THIS_MODULE, -- }, --}; -+static void swphy_poll_timer(unsigned long data) -+{ -+ struct bcm_enet_priv *priv = (struct bcm_enet_priv *)data; -+ unsigned int i; -+ -+ for (i = 0; i < priv->num_ports; i++) { -+ struct bcm63xx_enetsw_port *port; -+ int val, j, up, advertise, lpa, lpa2, speed, duplex, media; -+ int external_phy = bcm_enet_port_is_rgmii(i); -+ u8 override; -+ -+ port = &priv->used_ports[i]; -+ if (!port->used) -+ continue; -+ -+ if (port->bypass_link) -+ continue; -+ -+ /* dummy read to clear */ -+ for (j = 0; j < 2; j++) -+ val = bcmenet_sw_mdio_read(priv, external_phy, -+ port->phy_id, MII_BMSR); -+ -+ if (val == 0xffff) -+ continue; -+ -+ up = (val & BMSR_LSTATUS) ? 1 : 0; -+ if (!(up ^ priv->sw_port_link[i])) -+ continue; -+ -+ priv->sw_port_link[i] = up; -+ -+ /* link changed */ -+ if (!up) { -+ dev_info(&priv->pdev->dev, "link DOWN on %s\n", -+ port->name); -+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK, -+ ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | -+ ENETSW_PTCTRL_TXDIS_MASK, -+ ENETSW_PTCTRL_REG(i)); -+ continue; -+ } -+ -+ advertise = bcmenet_sw_mdio_read(priv, external_phy, -+ port->phy_id, MII_ADVERTISE); -+ -+ lpa = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id, -+ MII_LPA); -+ -+ lpa2 = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id, -+ MII_STAT1000); -+ -+ /* figure out media and duplex from advertise and LPA values */ -+ media = mii_nway_result(lpa & advertise); -+ duplex = (media & ADVERTISE_FULL) ? 1 : 0; -+ if (lpa2 & LPA_1000FULL) -+ duplex = 1; -+ -+ if (lpa2 & (LPA_1000FULL | LPA_1000HALF)) -+ speed = 1000; -+ else { -+ if (media & (ADVERTISE_100FULL | ADVERTISE_100HALF)) -+ speed = 100; -+ else -+ speed = 10; -+ } -+ -+ dev_info(&priv->pdev->dev, -+ "link UP on %s, %dMbps, %s-duplex\n", -+ port->name, speed, duplex ? "full" : "half"); -+ -+ override = ENETSW_PORTOV_ENABLE_MASK | -+ ENETSW_PORTOV_LINKUP_MASK; -+ -+ if (speed == 1000) -+ override |= ENETSW_IMPOV_1000_MASK; -+ else if (speed == 100) -+ override |= ENETSW_IMPOV_100_MASK; -+ if (duplex) -+ override |= ENETSW_IMPOV_FDX_MASK; -+ -+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i)); -+ } -+ -+ priv->swphy_poll.expires = jiffies + HZ; -+ add_timer(&priv->swphy_poll); -+} - - /* -- * entry point -+ * open callback, allocate dma rings & buffers and start rx operation - */ --static int __init bcm_enet_init(void) -+static int bcm_enetsw_open(struct net_device *dev) - { -- int ret; -+ struct bcm_enet_priv *priv; -+ struct device *kdev; -+ int i, ret; -+ unsigned int size; -+ void *p; -+ u32 val; - -- ret = platform_driver_register(&bcm63xx_enet_shared_driver); -- if (ret) -- return ret; -+ priv = netdev_priv(dev); -+ kdev = &priv->pdev->dev; - -- ret = platform_driver_register(&bcm63xx_enet_driver); -+ /* mask all interrupts and request them */ -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, -+ IRQF_DISABLED, dev->name, dev); - if (ret) -- platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ goto out_freeirq; -+ -+ if (priv->irq_tx != -1) { -+ ret = request_irq(priv->irq_tx, bcm_enet_isr_dma, -+ IRQF_DISABLED, dev->name, dev); -+ if (ret) -+ goto out_freeirq_rx; -+ } -+ -+ /* allocate rx dma ring */ -+ size = priv->rx_ring_size * sizeof(struct bcm_enet_desc); -+ p = dma_alloc_coherent(kdev, size, &priv->rx_desc_dma, GFP_KERNEL); -+ if (!p) { -+ dev_err(kdev, "cannot allocate rx ring %u\n", size); -+ ret = -ENOMEM; -+ goto out_freeirq_tx; -+ } -+ -+ memset(p, 0, size); -+ priv->rx_desc_alloc_size = size; -+ priv->rx_desc_cpu = p; -+ -+ /* allocate tx dma ring */ -+ size = priv->tx_ring_size * sizeof(struct bcm_enet_desc); -+ p = dma_alloc_coherent(kdev, size, &priv->tx_desc_dma, GFP_KERNEL); -+ if (!p) { -+ dev_err(kdev, "cannot allocate tx ring\n"); -+ ret = -ENOMEM; -+ goto out_free_rx_ring; -+ } -+ -+ memset(p, 0, size); -+ priv->tx_desc_alloc_size = size; -+ priv->tx_desc_cpu = p; -+ -+ priv->tx_skb = kzalloc(sizeof(struct sk_buff *) * priv->tx_ring_size, -+ GFP_KERNEL); -+ if (!priv->tx_skb) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out_free_tx_ring; -+ } -+ -+ priv->tx_desc_count = priv->tx_ring_size; -+ priv->tx_dirty_desc = 0; -+ priv->tx_curr_desc = 0; -+ spin_lock_init(&priv->tx_lock); -+ -+ /* init & fill rx ring with skbs */ -+ priv->rx_skb = kzalloc(sizeof(struct sk_buff *) * priv->rx_ring_size, -+ GFP_KERNEL); -+ if (!priv->rx_skb) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out_free_tx_skb; -+ } -+ -+ priv->rx_desc_count = 0; -+ priv->rx_dirty_desc = 0; -+ priv->rx_curr_desc = 0; -+ -+ /* disable all ports */ -+ for (i = 0; i < priv->num_ports; i++) { -+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK, -+ ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | -+ ENETSW_PTCTRL_TXDIS_MASK, -+ ENETSW_PTCTRL_REG(i)); -+ -+ priv->sw_port_link[i] = 0; -+ } -+ -+ /* reset mib */ -+ val = enetsw_readb(priv, ENETSW_GMCR_REG); -+ val |= ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ val &= ~ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ -+ /* force CPU port state */ -+ val = enetsw_readb(priv, ENETSW_IMPOV_REG); -+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -+ -+ /* enable switch forward engine */ -+ val = enetsw_readb(priv, ENETSW_SWMODE_REG); -+ val |= ENETSW_SWMODE_FWD_EN_MASK; -+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -+ -+ /* enable jumbo on all ports */ -+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -+ -+ /* initialize flow control buffer allocation */ -+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ -+ if (bcm_enet_refill_rx(dev)) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out; -+ } -+ -+ /* write rx & tx ring addresses */ -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->tx_chan)); -+ -+ /* clear remaining state ram for rx & tx channel */ -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ -+ /* set dma maximum burst len */ -+ enet_dmac_writel(priv, priv->dma_maxburst, -+ ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, priv->dma_maxburst, -+ ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ -+ /* set flow control low/high threshold to 1/3 / 2/3 */ -+ val = priv->rx_ring_size / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -+ val = (priv->rx_ring_size * 2) / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ -+ /* all set, enable mac and interrupts, start dma engine and -+ * kick rx dma channel -+ */ -+ wmb(); -+ enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ -+ /* watch "packet transferred" interrupt in rx and tx */ -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); -+ -+ /* make sure we enable napi before rx interrupt */ -+ napi_enable(&priv->napi); -+ -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ netif_carrier_on(dev); -+ netif_start_queue(dev); -+ -+ /* apply override config for bypass_link ports here. */ -+ for (i = 0; i < priv->num_ports; i++) { -+ struct bcm63xx_enetsw_port *port; -+ u8 override; -+ port = &priv->used_ports[i]; -+ if (!port->used) -+ continue; -+ -+ if (!port->bypass_link) -+ continue; -+ -+ override = ENETSW_PORTOV_ENABLE_MASK | -+ ENETSW_PORTOV_LINKUP_MASK; -+ -+ switch (port->force_speed) { -+ case 1000: -+ override |= ENETSW_IMPOV_1000_MASK; -+ break; -+ case 100: -+ override |= ENETSW_IMPOV_100_MASK; -+ break; -+ case 10: -+ break; -+ default: -+ pr_warn("invalid forced speed on port %s: assume 10\n", -+ port->name); -+ break; -+ } -+ -+ if (port->force_duplex_full) -+ override |= ENETSW_IMPOV_FDX_MASK; -+ -+ -+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i)); -+ } -+ -+ /* start phy polling timer */ -+ init_timer(&priv->swphy_poll); -+ priv->swphy_poll.function = swphy_poll_timer; -+ priv->swphy_poll.data = (unsigned long)priv; -+ priv->swphy_poll.expires = jiffies; -+ add_timer(&priv->swphy_poll); -+ return 0; -+ -+out: -+ for (i = 0; i < priv->rx_ring_size; i++) { -+ struct bcm_enet_desc *desc; -+ -+ if (!priv->rx_skb[i]) -+ continue; -+ -+ desc = &priv->rx_desc_cpu[i]; -+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size, -+ DMA_FROM_DEVICE); -+ kfree_skb(priv->rx_skb[i]); -+ } -+ kfree(priv->rx_skb); -+ -+out_free_tx_skb: -+ kfree(priv->tx_skb); -+ -+out_free_tx_ring: -+ dma_free_coherent(kdev, priv->tx_desc_alloc_size, -+ priv->tx_desc_cpu, priv->tx_desc_dma); -+ -+out_free_rx_ring: -+ dma_free_coherent(kdev, priv->rx_desc_alloc_size, -+ priv->rx_desc_cpu, priv->rx_desc_dma); -+ -+out_freeirq_tx: -+ if (priv->irq_tx != -1) -+ free_irq(priv->irq_tx, dev); -+ -+out_freeirq_rx: -+ free_irq(priv->irq_rx, dev); -+ -+out_freeirq: -+ return ret; -+} -+ -+/* stop callback */ -+static int bcm_enetsw_stop(struct net_device *dev) -+{ -+ struct bcm_enet_priv *priv; -+ struct device *kdev; -+ int i; -+ -+ priv = netdev_priv(dev); -+ kdev = &priv->pdev->dev; -+ -+ del_timer_sync(&priv->swphy_poll); -+ netif_stop_queue(dev); -+ napi_disable(&priv->napi); -+ del_timer_sync(&priv->rx_timeout); -+ -+ /* mask all interrupts */ -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ /* disable dma & mac */ -+ bcm_enet_disable_dma(priv, priv->tx_chan); -+ bcm_enet_disable_dma(priv, priv->rx_chan); -+ -+ /* force reclaim of all tx buffers */ -+ bcm_enet_tx_reclaim(dev, 1); -+ -+ /* free the rx skb ring */ -+ for (i = 0; i < priv->rx_ring_size; i++) { -+ struct bcm_enet_desc *desc; -+ -+ if (!priv->rx_skb[i]) -+ continue; -+ -+ desc = &priv->rx_desc_cpu[i]; -+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size, -+ DMA_FROM_DEVICE); -+ kfree_skb(priv->rx_skb[i]); -+ } -+ -+ /* free remaining allocated memory */ -+ kfree(priv->rx_skb); -+ kfree(priv->tx_skb); -+ dma_free_coherent(kdev, priv->rx_desc_alloc_size, -+ priv->rx_desc_cpu, priv->rx_desc_dma); -+ dma_free_coherent(kdev, priv->tx_desc_alloc_size, -+ priv->tx_desc_cpu, priv->tx_desc_dma); -+ if (priv->irq_tx != -1) -+ free_irq(priv->irq_tx, dev); -+ free_irq(priv->irq_rx, dev); -+ -+ return 0; -+} -+ -+/* try to sort out phy external status by walking the used_port field -+ * in the bcm_enet_priv structure. in case the phy address is not -+ * assigned to any physical port on the switch, assume it is external -+ * (and yell at the user). -+ */ -+static int bcm_enetsw_phy_is_external(struct bcm_enet_priv *priv, int phy_id) -+{ -+ int i; -+ -+ for (i = 0; i < priv->num_ports; ++i) { -+ if (!priv->used_ports[i].used) -+ continue; -+ if (priv->used_ports[i].phy_id == phy_id) -+ return bcm_enet_port_is_rgmii(i); -+ } -+ -+ printk_once(KERN_WARNING "bcm63xx_enet: could not find a used port with phy_id %i, assuming phy is external\n", -+ phy_id); -+ return 1; -+} -+ -+/* can't use bcmenet_sw_mdio_read directly as we need to sort out -+ * external/internal status of the given phy_id first. -+ */ -+static int bcm_enetsw_mii_mdio_read(struct net_device *dev, int phy_id, -+ int location) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ return bcmenet_sw_mdio_read(priv, -+ bcm_enetsw_phy_is_external(priv, phy_id), -+ phy_id, location); -+} -+ -+/* can't use bcmenet_sw_mdio_write directly as we need to sort out -+ * external/internal status of the given phy_id first. -+ */ -+static void bcm_enetsw_mii_mdio_write(struct net_device *dev, int phy_id, -+ int location, -+ int val) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ bcmenet_sw_mdio_write(priv, bcm_enetsw_phy_is_external(priv, phy_id), -+ phy_id, location, val); -+} -+ -+static int bcm_enetsw_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) -+{ -+ struct mii_if_info mii; -+ -+ mii.dev = dev; -+ mii.mdio_read = bcm_enetsw_mii_mdio_read; -+ mii.mdio_write = bcm_enetsw_mii_mdio_write; -+ mii.phy_id = 0; -+ mii.phy_id_mask = 0x3f; -+ mii.reg_num_mask = 0x1f; -+ return generic_mii_ioctl(&mii, if_mii(rq), cmd, NULL); -+ -+} -+ -+static const struct net_device_ops bcm_enetsw_ops = { -+ .ndo_open = bcm_enetsw_open, -+ .ndo_stop = bcm_enetsw_stop, -+ .ndo_start_xmit = bcm_enet_start_xmit, -+ .ndo_change_mtu = bcm_enet_change_mtu, -+ .ndo_do_ioctl = bcm_enetsw_ioctl, -+}; -+ -+ -+static const struct bcm_enet_stats bcm_enetsw_gstrings_stats[] = { -+ { "rx_packets", DEV_STAT(rx_packets), -1 }, -+ { "tx_packets", DEV_STAT(tx_packets), -1 }, -+ { "rx_bytes", DEV_STAT(rx_bytes), -1 }, -+ { "tx_bytes", DEV_STAT(tx_bytes), -1 }, -+ { "rx_errors", DEV_STAT(rx_errors), -1 }, -+ { "tx_errors", DEV_STAT(tx_errors), -1 }, -+ { "rx_dropped", DEV_STAT(rx_dropped), -1 }, -+ { "tx_dropped", DEV_STAT(tx_dropped), -1 }, -+ -+ { "tx_good_octets", GEN_STAT(mib.tx_gd_octets), ETHSW_MIB_RX_GD_OCT }, -+ { "tx_unicast", GEN_STAT(mib.tx_unicast), ETHSW_MIB_RX_BRDCAST }, -+ { "tx_broadcast", GEN_STAT(mib.tx_brdcast), ETHSW_MIB_RX_BRDCAST }, -+ { "tx_multicast", GEN_STAT(mib.tx_mult), ETHSW_MIB_RX_MULT }, -+ { "tx_64_octets", GEN_STAT(mib.tx_64), ETHSW_MIB_RX_64 }, -+ { "tx_65_127_oct", GEN_STAT(mib.tx_65_127), ETHSW_MIB_RX_65_127 }, -+ { "tx_128_255_oct", GEN_STAT(mib.tx_128_255), ETHSW_MIB_RX_128_255 }, -+ { "tx_256_511_oct", GEN_STAT(mib.tx_256_511), ETHSW_MIB_RX_256_511 }, -+ { "tx_512_1023_oct", GEN_STAT(mib.tx_512_1023), ETHSW_MIB_RX_512_1023}, -+ { "tx_1024_1522_oct", GEN_STAT(mib.tx_1024_max), -+ ETHSW_MIB_RX_1024_1522 }, -+ { "tx_1523_2047_oct", GEN_STAT(mib.tx_1523_2047), -+ ETHSW_MIB_RX_1523_2047 }, -+ { "tx_2048_4095_oct", GEN_STAT(mib.tx_2048_4095), -+ ETHSW_MIB_RX_2048_4095 }, -+ { "tx_4096_8191_oct", GEN_STAT(mib.tx_4096_8191), -+ ETHSW_MIB_RX_4096_8191 }, -+ { "tx_8192_9728_oct", GEN_STAT(mib.tx_8192_9728), -+ ETHSW_MIB_RX_8192_9728 }, -+ { "tx_oversize", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR }, -+ { "tx_oversize_drop", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR_DISC }, -+ { "tx_dropped", GEN_STAT(mib.tx_drop), ETHSW_MIB_RX_DROP }, -+ { "tx_undersize", GEN_STAT(mib.tx_underrun), ETHSW_MIB_RX_UND }, -+ { "tx_pause", GEN_STAT(mib.tx_pause), ETHSW_MIB_RX_PAUSE }, -+ -+ { "rx_good_octets", GEN_STAT(mib.rx_gd_octets), ETHSW_MIB_TX_ALL_OCT }, -+ { "rx_broadcast", GEN_STAT(mib.rx_brdcast), ETHSW_MIB_TX_BRDCAST }, -+ { "rx_multicast", GEN_STAT(mib.rx_mult), ETHSW_MIB_TX_MULT }, -+ { "rx_unicast", GEN_STAT(mib.rx_unicast), ETHSW_MIB_TX_MULT }, -+ { "rx_pause", GEN_STAT(mib.rx_pause), ETHSW_MIB_TX_PAUSE }, -+ { "rx_dropped", GEN_STAT(mib.rx_drop), ETHSW_MIB_TX_DROP_PKTS }, -+ -+}; -+ -+#define BCM_ENETSW_STATS_LEN \ -+ (sizeof(bcm_enetsw_gstrings_stats) / sizeof(struct bcm_enet_stats)) -+ -+static void bcm_enetsw_get_strings(struct net_device *netdev, -+ u32 stringset, u8 *data) -+{ -+ int i; -+ -+ switch (stringset) { -+ case ETH_SS_STATS: -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ memcpy(data + i * ETH_GSTRING_LEN, -+ bcm_enetsw_gstrings_stats[i].stat_string, -+ ETH_GSTRING_LEN); -+ } -+ break; -+ } -+} -+ -+static int bcm_enetsw_get_sset_count(struct net_device *netdev, -+ int string_set) -+{ -+ switch (string_set) { -+ case ETH_SS_STATS: -+ return BCM_ENETSW_STATS_LEN; -+ default: -+ return -EINVAL; -+ } -+} -+ -+static void bcm_enetsw_get_drvinfo(struct net_device *netdev, -+ struct ethtool_drvinfo *drvinfo) -+{ -+ strncpy(drvinfo->driver, bcm_enet_driver_name, 32); -+ strncpy(drvinfo->version, bcm_enet_driver_version, 32); -+ strncpy(drvinfo->fw_version, "N/A", 32); -+ strncpy(drvinfo->bus_info, "bcm63xx", 32); -+ drvinfo->n_stats = BCM_ENETSW_STATS_LEN; -+} -+ -+static void bcm_enetsw_get_ethtool_stats(struct net_device *netdev, -+ struct ethtool_stats *stats, -+ u64 *data) -+{ -+ struct bcm_enet_priv *priv; -+ int i; -+ -+ priv = netdev_priv(netdev); -+ -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ const struct bcm_enet_stats *s; -+ u32 lo, hi; -+ char *p; -+ int reg; -+ -+ s = &bcm_enetsw_gstrings_stats[i]; -+ -+ reg = s->mib_reg; -+ if (reg == -1) -+ continue; -+ -+ lo = enetsw_readl(priv, ENETSW_MIB_REG(reg)); -+ p = (char *)priv + s->stat_offset; -+ -+ if (s->sizeof_stat == sizeof(u64)) { -+ hi = enetsw_readl(priv, ENETSW_MIB_REG(reg + 1)); -+ *(u64 *)p = ((u64)hi << 32 | lo); -+ } else { -+ *(u32 *)p = lo; -+ } -+ } -+ -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ const struct bcm_enet_stats *s; -+ char *p; -+ -+ s = &bcm_enetsw_gstrings_stats[i]; -+ -+ if (s->mib_reg == -1) -+ p = (char *)&netdev->stats + s->stat_offset; -+ else -+ p = (char *)priv + s->stat_offset; -+ -+ data[i] = (s->sizeof_stat == sizeof(u64)) ? -+ *(u64 *)p : *(u32 *)p; -+ } -+} -+ -+static void bcm_enetsw_get_ringparam(struct net_device *dev, -+ struct ethtool_ringparam *ering) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ -+ /* rx/tx ring is actually only limited by memory */ -+ ering->rx_max_pending = 8192; -+ ering->tx_max_pending = 8192; -+ ering->rx_mini_max_pending = 0; -+ ering->rx_jumbo_max_pending = 0; -+ ering->rx_pending = priv->rx_ring_size; -+ ering->tx_pending = priv->tx_ring_size; -+} -+ -+static int bcm_enetsw_set_ringparam(struct net_device *dev, -+ struct ethtool_ringparam *ering) -+{ -+ struct bcm_enet_priv *priv; -+ int was_running; -+ -+ priv = netdev_priv(dev); -+ -+ was_running = 0; -+ if (netif_running(dev)) { -+ bcm_enetsw_stop(dev); -+ was_running = 1; -+ } -+ -+ priv->rx_ring_size = ering->rx_pending; -+ priv->tx_ring_size = ering->tx_pending; -+ -+ if (was_running) { -+ int err; -+ -+ err = bcm_enetsw_open(dev); -+ if (err) -+ dev_close(dev); -+ } -+ return 0; -+} -+ -+static struct ethtool_ops bcm_enetsw_ethtool_ops = { -+ .get_strings = bcm_enetsw_get_strings, -+ .get_sset_count = bcm_enetsw_get_sset_count, -+ .get_ethtool_stats = bcm_enetsw_get_ethtool_stats, -+ .get_drvinfo = bcm_enetsw_get_drvinfo, -+ .get_ringparam = bcm_enetsw_get_ringparam, -+ .set_ringparam = bcm_enetsw_set_ringparam, -+}; -+ -+/* allocate netdevice, request register memory and register device. */ -+static int bcm_enetsw_probe(struct platform_device *pdev) -+{ -+ struct bcm_enet_priv *priv; -+ struct net_device *dev; -+ struct bcm63xx_enetsw_platform_data *pd; -+ struct resource *res_mem; -+ int ret, irq_rx, irq_tx; -+ -+ /* stop if shared driver failed, assume driver->probe will be -+ * called in the same order we register devices (correct ?) -+ */ -+ if (!bcm_enet_shared_base[0]) -+ return -ENODEV; -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ irq_rx = platform_get_irq(pdev, 0); -+ irq_tx = platform_get_irq(pdev, 1); -+ if (!res_mem || irq_rx < 0) -+ return -ENODEV; -+ -+ ret = 0; -+ dev = alloc_etherdev(sizeof(*priv)); -+ if (!dev) -+ return -ENOMEM; -+ priv = netdev_priv(dev); -+ memset(priv, 0, sizeof(*priv)); -+ -+ /* initialize default and fetch platform data */ -+ priv->enet_is_sw = true; -+ priv->irq_rx = irq_rx; -+ priv->irq_tx = irq_tx; -+ priv->rx_ring_size = BCMENET_DEF_RX_DESC; -+ priv->tx_ring_size = BCMENET_DEF_TX_DESC; -+ priv->dma_maxburst = BCMENETSW_DMA_MAXBURST; -+ -+ pd = pdev->dev.platform_data; -+ if (pd) { -+ memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN); -+ memcpy(priv->used_ports, pd->used_ports, -+ sizeof(pd->used_ports)); -+ priv->num_ports = pd->num_ports; -+ } -+ -+ ret = compute_hw_mtu(priv, dev->mtu); -+ if (ret) -+ goto out; -+ -+ if (!request_mem_region(res_mem->start, resource_size(res_mem), -+ "bcm63xx_enetsw")) { -+ ret = -EBUSY; -+ goto out; -+ } -+ -+ priv->base = ioremap(res_mem->start, resource_size(res_mem)); -+ if (priv->base == NULL) { -+ ret = -ENOMEM; -+ goto out_release_mem; -+ } -+ -+ priv->mac_clk = clk_get(&pdev->dev, "enetsw"); -+ if (IS_ERR(priv->mac_clk)) { -+ ret = PTR_ERR(priv->mac_clk); -+ goto out_unmap; -+ } -+ clk_enable(priv->mac_clk); -+ -+ priv->rx_chan = 0; -+ priv->tx_chan = 1; -+ spin_lock_init(&priv->rx_lock); -+ -+ /* init rx timeout (used for oom) */ -+ init_timer(&priv->rx_timeout); -+ priv->rx_timeout.function = bcm_enet_refill_rx_timer; -+ priv->rx_timeout.data = (unsigned long)dev; -+ -+ /* register netdevice */ -+ dev->netdev_ops = &bcm_enetsw_ops; -+ netif_napi_add(dev, &priv->napi, bcm_enet_poll, 16); -+ SET_ETHTOOL_OPS(dev, &bcm_enetsw_ethtool_ops); -+ SET_NETDEV_DEV(dev, &pdev->dev); -+ -+ spin_lock_init(&priv->enetsw_mdio_lock); -+ -+ ret = register_netdev(dev); -+ if (ret) -+ goto out_put_clk; -+ -+ netif_carrier_off(dev); -+ platform_set_drvdata(pdev, dev); -+ priv->pdev = pdev; -+ priv->net_dev = dev; -+ -+ return 0; -+ -+out_put_clk: -+ clk_put(priv->mac_clk); -+ -+out_unmap: -+ iounmap(priv->base); -+ -+out_release_mem: -+ release_mem_region(res_mem->start, resource_size(res_mem)); -+out: -+ free_netdev(dev); -+ return ret; -+} -+ -+ -+/* exit func, stops hardware and unregisters netdevice */ -+static int bcm_enetsw_remove(struct platform_device *pdev) -+{ -+ struct bcm_enet_priv *priv; -+ struct net_device *dev; -+ struct resource *res; -+ -+ /* stop netdevice */ -+ dev = platform_get_drvdata(pdev); -+ priv = netdev_priv(dev); -+ unregister_netdev(dev); -+ -+ /* release device resources */ -+ iounmap(priv->base); -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ release_mem_region(res->start, resource_size(res)); -+ -+ platform_set_drvdata(pdev, NULL); -+ free_netdev(dev); -+ return 0; -+} -+ -+struct platform_driver bcm63xx_enetsw_driver = { -+ .probe = bcm_enetsw_probe, -+ .remove = bcm_enetsw_remove, -+ .driver = { -+ .name = "bcm63xx_enetsw", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+/* reserve & remap memory space shared between all macs */ -+static int bcm_enet_shared_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ void __iomem *p[3]; -+ unsigned int i; -+ -+ memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base)); -+ -+ for (i = 0; i < 3; i++) { -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ p[i] = devm_ioremap_resource(&pdev->dev, res); -+ if (!p[i]) -+ return -ENOMEM; -+ } -+ -+ memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base)); -+ -+ return 0; -+} -+ -+static int bcm_enet_shared_remove(struct platform_device *pdev) -+{ -+ return 0; -+} -+ -+/* this "shared" driver is needed because both macs share a single -+ * address space -+ */ -+struct platform_driver bcm63xx_enet_shared_driver = { -+ .probe = bcm_enet_shared_probe, -+ .remove = bcm_enet_shared_remove, -+ .driver = { -+ .name = "bcm63xx_enet_shared", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+/* entry point */ -+static int __init bcm_enet_init(void) -+{ -+ int ret; -+ -+ ret = platform_driver_register(&bcm63xx_enet_shared_driver); -+ if (ret) -+ return ret; -+ -+ ret = platform_driver_register(&bcm63xx_enet_driver); -+ if (ret) -+ platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ -+ ret = platform_driver_register(&bcm63xx_enetsw_driver); -+ if (ret) { -+ platform_driver_unregister(&bcm63xx_enet_driver); -+ platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ } - - return ret; - } -@@ -1962,6 +2876,7 @@ static int __init bcm_enet_init(void) - static void __exit bcm_enet_exit(void) - { - platform_driver_unregister(&bcm63xx_enet_driver); -+ platform_driver_unregister(&bcm63xx_enetsw_driver); - platform_driver_unregister(&bcm63xx_enet_shared_driver); - } - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -18,6 +18,7 @@ - - /* maximum burst len for dma (4 bytes unit) */ - #define BCMENET_DMA_MAXBURST 16 -+#define BCMENETSW_DMA_MAXBURST 8 - - /* tx transmit threshold (4 bytes unit), fifo is 256 bytes, the value - * must be low enough so that a DMA transfer of above burst length can -@@ -84,11 +85,60 @@ - #define ETH_MIB_RX_CNTRL 54 - - -+/* -+ * SW MIB Counters register definitions -+*/ -+#define ETHSW_MIB_TX_ALL_OCT 0 -+#define ETHSW_MIB_TX_DROP_PKTS 2 -+#define ETHSW_MIB_TX_QOS_PKTS 3 -+#define ETHSW_MIB_TX_BRDCAST 4 -+#define ETHSW_MIB_TX_MULT 5 -+#define ETHSW_MIB_TX_UNI 6 -+#define ETHSW_MIB_TX_COL 7 -+#define ETHSW_MIB_TX_1_COL 8 -+#define ETHSW_MIB_TX_M_COL 9 -+#define ETHSW_MIB_TX_DEF 10 -+#define ETHSW_MIB_TX_LATE 11 -+#define ETHSW_MIB_TX_EX_COL 12 -+#define ETHSW_MIB_TX_PAUSE 14 -+#define ETHSW_MIB_TX_QOS_OCT 15 -+ -+#define ETHSW_MIB_RX_ALL_OCT 17 -+#define ETHSW_MIB_RX_UND 19 -+#define ETHSW_MIB_RX_PAUSE 20 -+#define ETHSW_MIB_RX_64 21 -+#define ETHSW_MIB_RX_65_127 22 -+#define ETHSW_MIB_RX_128_255 23 -+#define ETHSW_MIB_RX_256_511 24 -+#define ETHSW_MIB_RX_512_1023 25 -+#define ETHSW_MIB_RX_1024_1522 26 -+#define ETHSW_MIB_RX_OVR 27 -+#define ETHSW_MIB_RX_JAB 28 -+#define ETHSW_MIB_RX_ALIGN 29 -+#define ETHSW_MIB_RX_CRC 30 -+#define ETHSW_MIB_RX_GD_OCT 31 -+#define ETHSW_MIB_RX_DROP 33 -+#define ETHSW_MIB_RX_UNI 34 -+#define ETHSW_MIB_RX_MULT 35 -+#define ETHSW_MIB_RX_BRDCAST 36 -+#define ETHSW_MIB_RX_SA_CHANGE 37 -+#define ETHSW_MIB_RX_FRAG 38 -+#define ETHSW_MIB_RX_OVR_DISC 39 -+#define ETHSW_MIB_RX_SYM 40 -+#define ETHSW_MIB_RX_QOS_PKTS 41 -+#define ETHSW_MIB_RX_QOS_OCT 42 -+#define ETHSW_MIB_RX_1523_2047 44 -+#define ETHSW_MIB_RX_2048_4095 45 -+#define ETHSW_MIB_RX_4096_8191 46 -+#define ETHSW_MIB_RX_8192_9728 47 -+ -+ - struct bcm_enet_mib_counters { - u64 tx_gd_octets; - u32 tx_gd_pkts; - u32 tx_all_octets; - u32 tx_all_pkts; -+ u32 tx_unicast; - u32 tx_brdcast; - u32 tx_mult; - u32 tx_64; -@@ -97,7 +147,12 @@ struct bcm_enet_mib_counters { - u32 tx_256_511; - u32 tx_512_1023; - u32 tx_1024_max; -+ u32 tx_1523_2047; -+ u32 tx_2048_4095; -+ u32 tx_4096_8191; -+ u32 tx_8192_9728; - u32 tx_jab; -+ u32 tx_drop; - u32 tx_ovr; - u32 tx_frag; - u32 tx_underrun; -@@ -114,6 +169,7 @@ struct bcm_enet_mib_counters { - u32 rx_all_octets; - u32 rx_all_pkts; - u32 rx_brdcast; -+ u32 rx_unicast; - u32 rx_mult; - u32 rx_64; - u32 rx_65_127; -@@ -197,6 +253,9 @@ struct bcm_enet_priv { - /* number of dma desc in tx ring */ - int tx_ring_size; - -+ /* maximum dma burst size */ -+ int dma_maxburst; -+ - /* cpu view of rx dma ring */ - struct bcm_enet_desc *tx_desc_cpu; - -@@ -269,6 +328,18 @@ struct bcm_enet_priv { - - /* maximum hardware transmit/receive size */ - unsigned int hw_mtu; -+ -+ bool enet_is_sw; -+ -+ /* port mapping for switch devices */ -+ int num_ports; -+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+ int sw_port_link[ENETSW_MAX_PORT]; -+ -+ /* used to poll switch port state */ -+ struct timer_list swphy_poll; -+ spinlock_t enetsw_mdio_lock; - }; - -+ - #endif /* ! BCM63XX_ENET_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/048-bcm63xx_enet-add-support-Broadcom-BCM6345-Ethernet.patch b/target/linux/brcm63xx/patches-3.9/048-bcm63xx_enet-add-support-Broadcom-BCM6345-Ethernet.patch deleted file mode 100644 index f0b20e9658..0000000000 --- a/target/linux/brcm63xx/patches-3.9/048-bcm63xx_enet-add-support-Broadcom-BCM6345-Ethernet.patch +++ /dev/null @@ -1,838 +0,0 @@ -From fb7e08ec47f7168b8f4f72d8e3b5bcf625e1089e Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Wed, 12 Jun 2013 18:53:05 +0000 -Subject: [PATCH] bcm63xx_enet: add support Broadcom BCM6345 Ethernet - -This patch adds support for the Broadcom BCM6345 SoC Ethernet. BCM6345 -has a slightly different and older DMA engine which requires the -following modifications: - -- the width of the DMA channels on BCM6345 is 64 bytes vs 16 bytes, - which means that the helpers enet_dma{c,s} need to account for this - channel width and we can no longer use macros - -- BCM6345 DMA engine does not have any internal SRAM for transfering - buffers - -- BCM6345 buffer allocation and flow control is not per-channel but - global (done in RSET_ENETDMA) - -- the DMA engine bits are right-shifted by 3 compared to other DMA - generations - -- the DMA enable/interrupt masks are a little different (we need to - enabled more bits for 6345) - -- some register have the same meaning but are offsetted in the ENET_DMAC - space so a lookup table is required to return the proper offset - -The MAC itself is identical and requires no modifications to work. - -Signed-off-by: Florian Fainelli -Acked-by: Ralf Baechle ---- - arch/mips/bcm63xx/dev-enet.c | 65 ++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 3 +- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 94 +++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 43 ++++- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 200 ++++++++++++-------- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 15 ++ - 6 files changed, 329 insertions(+), 91 deletions(-) - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -9,10 +9,44 @@ - #include - #include - #include -+#include - #include - #include - #include - -+#ifdef BCMCPU_RUNTIME_DETECT -+static const unsigned long bcm6348_regs_enetdmac[] = { -+ [ENETDMAC_CHANCFG] = ENETDMAC_CHANCFG_REG, -+ [ENETDMAC_IR] = ENETDMAC_IR_REG, -+ [ENETDMAC_IRMASK] = ENETDMAC_IRMASK_REG, -+ [ENETDMAC_MAXBURST] = ENETDMAC_MAXBURST_REG, -+}; -+ -+static const unsigned long bcm6345_regs_enetdmac[] = { -+ [ENETDMAC_CHANCFG] = ENETDMA_6345_CHANCFG_REG, -+ [ENETDMAC_IR] = ENETDMA_6345_IR_REG, -+ [ENETDMAC_IRMASK] = ENETDMA_6345_IRMASK_REG, -+ [ENETDMAC_MAXBURST] = ENETDMA_6345_MAXBURST_REG, -+ [ENETDMAC_BUFALLOC] = ENETDMA_6345_BUFALLOC_REG, -+ [ENETDMAC_RSTART] = ENETDMA_6345_RSTART_REG, -+ [ENETDMAC_FC] = ENETDMA_6345_FC_REG, -+ [ENETDMAC_LEN] = ENETDMA_6345_LEN_REG, -+}; -+ -+const unsigned long *bcm63xx_regs_enetdmac; -+EXPORT_SYMBOL(bcm63xx_regs_enetdmac); -+ -+static __init void bcm63xx_enetdmac_regs_init(void) -+{ -+ if (BCMCPU_IS_6345()) -+ bcm63xx_regs_enetdmac = bcm6345_regs_enetdmac; -+ else -+ bcm63xx_regs_enetdmac = bcm6348_regs_enetdmac; -+} -+#else -+static __init void bcm63xx_enetdmac_regs_init(void) { } -+#endif -+ - static struct resource shared_res[] = { - { - .start = -1, /* filled at runtime */ -@@ -137,12 +171,19 @@ static int __init register_shared(void) - if (shared_device_registered) - return 0; - -+ bcm63xx_enetdmac_regs_init(); -+ - shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); - shared_res[0].end = shared_res[0].start; -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ if (BCMCPU_IS_6345()) -+ shared_res[0].end += (RSET_6345_ENETDMA_SIZE) - 1; -+ else -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; - - if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) - chan_count = 32; -+ else if (BCMCPU_IS_6345()) -+ chan_count = 8; - else - chan_count = 16; - -@@ -172,7 +213,7 @@ int __init bcm63xx_enet_register(int uni - if (unit > 1) - return -ENODEV; - -- if (unit == 1 && BCMCPU_IS_6338()) -+ if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345())) - return -ENODEV; - - ret = register_shared(); -@@ -213,6 +254,21 @@ int __init bcm63xx_enet_register(int uni - dpd->phy_interrupt = bcm63xx_get_irq_number(IRQ_ENET_PHY); - } - -+ dpd->dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK; -+ dpd->dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK; -+ if (BCMCPU_IS_6345()) { -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_CHAINING_MASK; -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_WRAP_EN_MASK; -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_FLOWC_EN_MASK; -+ dpd->dma_chan_int_mask |= ENETDMA_IR_BUFDONE_MASK; -+ dpd->dma_chan_int_mask |= ENETDMA_IR_NOTOWNER_MASK; -+ dpd->dma_chan_width = ENETDMA_6345_CHAN_WIDTH; -+ dpd->dma_desc_shift = ENETDMA_6345_DESC_SHIFT; -+ } else { -+ dpd->dma_has_sram = true; -+ dpd->dma_chan_width = ENETDMA_CHAN_WIDTH; -+ } -+ - ret = platform_device_register(pdev); - if (ret) - return ret; -@@ -246,6 +302,11 @@ bcm63xx_enetsw_register(const struct bcm - else if (BCMCPU_IS_6362() || BCMCPU_IS_6368()) - enetsw_pd.num_ports = ENETSW_PORTS_6368; - -+ enetsw_pd.dma_has_sram = true; -+ enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH; -+ enetsw_pd.dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK; -+ enetsw_pd.dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK; -+ - ret = platform_device_register(&bcm63xx_enetsw_device); - if (ret) - return ret; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -188,6 +188,7 @@ enum bcm63xx_regs_set { - #define BCM_6368_RSET_SPI_SIZE 1804 - #define RSET_ENET_SIZE 2048 - #define RSET_ENETDMA_SIZE 256 -+#define RSET_6345_ENETDMA_SIZE 64 - #define RSET_ENETDMAC_SIZE(chans) (16 * (chans)) - #define RSET_ENETDMAS_SIZE(chans) (16 * (chans)) - #define RSET_ENETSW_SIZE 65536 -@@ -363,7 +364,7 @@ enum bcm63xx_regs_set { - #define BCM_6345_USBDMA_BASE (0xfffe2800) - #define BCM_6345_ENET0_BASE (0xfffe1800) - #define BCM_6345_ENETDMA_BASE (0xfffe2800) --#define BCM_6345_ENETDMAC_BASE (0xfffe2900) -+#define BCM_6345_ENETDMAC_BASE (0xfffe2840) - #define BCM_6345_ENETDMAS_BASE (0xfffe2a00) - #define BCM_6345_ENETSW_BASE (0xdeadbeef) - #define BCM_6345_PCMCIA_BASE (0xfffe2028) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -4,6 +4,8 @@ - #include - #include - -+#include -+ - /* - * on board ethernet platform data - */ -@@ -37,6 +39,21 @@ struct bcm63xx_enet_platform_data { - int phy_id, int reg), - void (*mii_write)(struct net_device *dev, - int phy_id, int reg, int val)); -+ -+ /* DMA channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* DMA channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* DMA engine has internal SRAM */ -+ bool dma_has_sram; -+ -+ /* DMA channel register width */ -+ unsigned int dma_chan_width; -+ -+ /* DMA descriptor shift */ -+ unsigned int dma_desc_shift; - }; - - /* -@@ -63,6 +80,18 @@ struct bcm63xx_enetsw_platform_data { - char mac_addr[ETH_ALEN]; - int num_ports; - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+ -+ /* DMA channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* DMA channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* DMA channel register width */ -+ unsigned int dma_chan_width; -+ -+ /* DMA engine has internal SRAM */ -+ bool dma_has_sram; - }; - - int __init bcm63xx_enet_register(int unit, -@@ -70,4 +99,69 @@ int __init bcm63xx_enet_register(int uni - - int bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd); - -+enum bcm63xx_regs_enetdmac { -+ ENETDMAC_CHANCFG, -+ ENETDMAC_IR, -+ ENETDMAC_IRMASK, -+ ENETDMAC_MAXBURST, -+ ENETDMAC_BUFALLOC, -+ ENETDMAC_RSTART, -+ ENETDMAC_FC, -+ ENETDMAC_LEN, -+}; -+ -+static inline unsigned long bcm63xx_enetdmacreg(enum bcm63xx_regs_enetdmac reg) -+{ -+#ifdef BCMCPU_RUNTIME_DETECT -+ extern const unsigned long *bcm63xx_regs_enetdmac; -+ -+ return bcm63xx_regs_enetdmac[reg]; -+#else -+#ifdef CONFIG_BCM63XX_CPU_6345 -+ switch (reg) { -+ case ENETDMAC_CHANCFG: -+ return ENETDMA_6345_CHANCFG_REG; -+ case ENETDMAC_IR: -+ return ENETDMA_6345_IR_REG; -+ case ENETDMAC_IRMASK: -+ return ENETDMA_6345_IRMASK_REG; -+ case ENETDMAC_MAXBURST: -+ return ENETDMA_6345_MAXBURST_REG; -+ case ENETDMAC_BUFALLOC: -+ return ENETDMA_6345_BUFALLOC_REG; -+ case ENETDMAC_RSTART: -+ return ENETDMA_6345_RSTART_REG; -+ case ENETDMAC_FC: -+ return ENETDMA_6345_FC_REG; -+ case ENETDMAC_LEN: -+ return ENETDMA_6345_LEN_REG; -+ } -+#endif -+#if defined(CONFIG_BCM63XX_CPU_6328) || \ -+ defined(CONFIG_BCM63XX_CPU_6338) || \ -+ defined(CONFIG_BCM63XX_CPU_6348) || \ -+ defined(CONFIG_BCM63XX_CPU_6358) || \ -+ defined(CONFIG_BCM63XX_CPU_6362) || \ -+ defined(CONFIG_BCM63XX_CPU_6368) -+ switch (reg) { -+ case ENETDMAC_CHANCFG: -+ return ENETDMAC_CHANCFG_REG; -+ case ENETDMAC_IR: -+ return ENETDMAC_IR_REG; -+ case ENETDMAC_IRMASK: -+ return ENETDMAC_IRMASK_REG; -+ case ENETDMAC_MAXBURST: -+ return ENETDMAC_MAXBURST_REG; -+ case ENETDMAC_BUFALLOC: -+ case ENETDMAC_RSTART: -+ case ENETDMAC_FC: -+ case ENETDMAC_LEN: -+ return 0; -+ } -+#endif -+#endif -+ return 0; -+} -+ -+ - #endif /* ! BCM63XX_DEV_ENET_H_ */ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -770,6 +770,8 @@ - /************************************************************************* - * _REG relative to RSET_ENETDMA - *************************************************************************/ -+#define ENETDMA_CHAN_WIDTH 0x10 -+#define ENETDMA_6345_CHAN_WIDTH 0x40 - - /* Controller Configuration Register */ - #define ENETDMA_CFG_REG (0x0) -@@ -825,31 +827,56 @@ - /* State Ram Word 4 */ - #define ENETDMA_SRAM4_REG(x) (0x20c + (x) * 0x10) - -+/* Broadcom 6345 ENET DMA definitions */ -+#define ENETDMA_6345_CHANCFG_REG (0x00) -+ -+#define ENETDMA_6345_MAXBURST_REG (0x40) -+ -+#define ENETDMA_6345_RSTART_REG (0x08) -+ -+#define ENETDMA_6345_LEN_REG (0x0C) -+ -+#define ENETDMA_6345_IR_REG (0x14) -+ -+#define ENETDMA_6345_IRMASK_REG (0x18) -+ -+#define ENETDMA_6345_FC_REG (0x1C) -+ -+#define ENETDMA_6345_BUFALLOC_REG (0x20) -+ -+/* Shift down for EOP, SOP and WRAP bits */ -+#define ENETDMA_6345_DESC_SHIFT (3) - - /************************************************************************* - * _REG relative to RSET_ENETDMAC - *************************************************************************/ - - /* Channel Configuration register */ --#define ENETDMAC_CHANCFG_REG(x) ((x) * 0x10) -+#define ENETDMAC_CHANCFG_REG (0x0) - #define ENETDMAC_CHANCFG_EN_SHIFT 0 - #define ENETDMAC_CHANCFG_EN_MASK (1 << ENETDMAC_CHANCFG_EN_SHIFT) - #define ENETDMAC_CHANCFG_PKTHALT_SHIFT 1 - #define ENETDMAC_CHANCFG_PKTHALT_MASK (1 << ENETDMAC_CHANCFG_PKTHALT_SHIFT) - #define ENETDMAC_CHANCFG_BUFHALT_SHIFT 2 - #define ENETDMAC_CHANCFG_BUFHALT_MASK (1 << ENETDMAC_CHANCFG_BUFHALT_SHIFT) -+#define ENETDMAC_CHANCFG_CHAINING_SHIFT 2 -+#define ENETDMAC_CHANCFG_CHAINING_MASK (1 << ENETDMAC_CHANCFG_CHAINING_SHIFT) -+#define ENETDMAC_CHANCFG_WRAP_EN_SHIFT 3 -+#define ENETDMAC_CHANCFG_WRAP_EN_MASK (1 << ENETDMAC_CHANCFG_WRAP_EN_SHIFT) -+#define ENETDMAC_CHANCFG_FLOWC_EN_SHIFT 4 -+#define ENETDMAC_CHANCFG_FLOWC_EN_MASK (1 << ENETDMAC_CHANCFG_FLOWC_EN_SHIFT) - - /* Interrupt Control/Status register */ --#define ENETDMAC_IR_REG(x) (0x4 + (x) * 0x10) -+#define ENETDMAC_IR_REG (0x4) - #define ENETDMAC_IR_BUFDONE_MASK (1 << 0) - #define ENETDMAC_IR_PKTDONE_MASK (1 << 1) - #define ENETDMAC_IR_NOTOWNER_MASK (1 << 2) - - /* Interrupt Mask register */ --#define ENETDMAC_IRMASK_REG(x) (0x8 + (x) * 0x10) -+#define ENETDMAC_IRMASK_REG (0x8) - - /* Maximum Burst Length */ --#define ENETDMAC_MAXBURST_REG(x) (0xc + (x) * 0x10) -+#define ENETDMAC_MAXBURST_REG (0xc) - - - /************************************************************************* -@@ -857,16 +884,16 @@ - *************************************************************************/ - - /* Ring Start Address register */ --#define ENETDMAS_RSTART_REG(x) ((x) * 0x10) -+#define ENETDMAS_RSTART_REG (0x0) - - /* State Ram Word 2 */ --#define ENETDMAS_SRAM2_REG(x) (0x4 + (x) * 0x10) -+#define ENETDMAS_SRAM2_REG (0x4) - - /* State Ram Word 3 */ --#define ENETDMAS_SRAM3_REG(x) (0x8 + (x) * 0x10) -+#define ENETDMAS_SRAM3_REG (0x8) - - /* State Ram Word 4 */ --#define ENETDMAS_SRAM4_REG(x) (0xc + (x) * 0x10) -+#define ENETDMAS_SRAM4_REG (0xc) - - - /************************************************************************* ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -107,26 +107,28 @@ static inline void enet_dma_writel(struc - bcm_writel(val, bcm_enet_shared_base[0] + off); - } - --static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off) -+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off, int chan) - { -- return bcm_readl(bcm_enet_shared_base[1] + off); -+ return bcm_readl(bcm_enet_shared_base[1] + -+ bcm63xx_enetdmacreg(off) + chan * priv->dma_chan_width); - } - - static inline void enet_dmac_writel(struct bcm_enet_priv *priv, -- u32 val, u32 off) -+ u32 val, u32 off, int chan) - { -- bcm_writel(val, bcm_enet_shared_base[1] + off); -+ bcm_writel(val, bcm_enet_shared_base[1] + -+ bcm63xx_enetdmacreg(off) + chan * priv->dma_chan_width); - } - --static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off) -+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off, int chan) - { -- return bcm_readl(bcm_enet_shared_base[2] + off); -+ return bcm_readl(bcm_enet_shared_base[2] + off + chan * priv->dma_chan_width); - } - - static inline void enet_dmas_writel(struct bcm_enet_priv *priv, -- u32 val, u32 off) -+ u32 val, u32 off, int chan) - { -- bcm_writel(val, bcm_enet_shared_base[2] + off); -+ bcm_writel(val, bcm_enet_shared_base[2] + off + chan * priv->dma_chan_width); - } - - /* -@@ -262,7 +264,7 @@ static int bcm_enet_refill_rx(struct net - len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT; - len_stat |= DMADESC_OWNER_MASK; - if (priv->rx_dirty_desc == priv->rx_ring_size - 1) { -- len_stat |= DMADESC_WRAP_MASK; -+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift); - priv->rx_dirty_desc = 0; - } else { - priv->rx_dirty_desc++; -@@ -273,7 +275,10 @@ static int bcm_enet_refill_rx(struct net - priv->rx_desc_count++; - - /* tell dma engine we allocated one buffer */ -- enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ if (priv->dma_has_sram) -+ enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ else -+ enet_dmac_writel(priv, 1, ENETDMAC_BUFALLOC, priv->rx_chan); - } - - /* If rx ring is still empty, set a timer to try allocating -@@ -349,7 +354,8 @@ static int bcm_enet_receive_queue(struct - - /* if the packet does not have start of packet _and_ - * end of packet flag set, then just recycle it */ -- if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) { -+ if ((len_stat & (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) != -+ (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) { - dev->stats.rx_dropped++; - continue; - } -@@ -410,8 +416,8 @@ static int bcm_enet_receive_queue(struct - bcm_enet_refill_rx(dev); - - /* kick rx dma */ -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->rx_chan); - } - - return processed; -@@ -486,10 +492,10 @@ static int bcm_enet_poll(struct napi_str - dev = priv->net_dev; - - /* ack interrupts */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->tx_chan); - - /* reclaim sent skb */ - tx_work_done = bcm_enet_tx_reclaim(dev, 0); -@@ -508,10 +514,10 @@ static int bcm_enet_poll(struct napi_str - napi_complete(napi); - - /* restore rx/tx interrupt */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->tx_chan); - - return rx_work_done; - } -@@ -554,8 +560,8 @@ static irqreturn_t bcm_enet_isr_dma(int - priv = netdev_priv(dev); - - /* mask rx/tx interrupts */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - napi_schedule(&priv->napi); - -@@ -616,14 +622,14 @@ static int bcm_enet_start_xmit(struct sk - DMA_TO_DEVICE); - - len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK; -- len_stat |= DMADESC_ESOP_MASK | -+ len_stat |= (DMADESC_ESOP_MASK >> priv->dma_desc_shift) | - DMADESC_APPEND_CRC | - DMADESC_OWNER_MASK; - - priv->tx_curr_desc++; - if (priv->tx_curr_desc == priv->tx_ring_size) { - priv->tx_curr_desc = 0; -- len_stat |= DMADESC_WRAP_MASK; -+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift); - } - priv->tx_desc_count--; - -@@ -634,8 +640,8 @@ static int bcm_enet_start_xmit(struct sk - wmb(); - - /* kick tx dma */ -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->tx_chan); - - /* stop queue if no more desc available */ - if (!priv->tx_desc_count) -@@ -763,6 +769,9 @@ static void bcm_enet_set_flow(struct bcm - val &= ~ENET_RXCFG_ENFLOW_MASK; - enet_writel(priv, val, ENET_RXCFG_REG); - -+ if (!priv->dma_has_sram) -+ return; -+ - /* tx flow control (pause frame generation) */ - val = enet_dma_readl(priv, ENETDMA_CFG_REG); - if (tx_en) -@@ -910,8 +919,8 @@ static int bcm_enet_open(struct net_devi - - /* mask all interrupts and request them */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -@@ -988,8 +997,12 @@ static int bcm_enet_open(struct net_devi - priv->rx_curr_desc = 0; - - /* initialize flow control buffer allocation */ -- enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -- ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ if (priv->dma_has_sram) -+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ else -+ enet_dmac_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMAC_BUFALLOC, priv->rx_chan); - - if (bcm_enet_refill_rx(dev)) { - dev_err(kdev, "cannot allocate rx skb queue\n"); -@@ -998,18 +1011,30 @@ static int bcm_enet_open(struct net_devi - } - - /* write rx & tx ring addresses */ -- enet_dmas_writel(priv, priv->rx_desc_dma, -- ENETDMAS_RSTART_REG(priv->rx_chan)); -- enet_dmas_writel(priv, priv->tx_desc_dma, -- ENETDMAS_RSTART_REG(priv->tx_chan)); -+ if (priv->dma_has_sram) { -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG, priv->rx_chan); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG, priv->tx_chan); -+ } else { -+ enet_dmac_writel(priv, priv->rx_desc_dma, -+ ENETDMAC_RSTART, priv->rx_chan); -+ enet_dmac_writel(priv, priv->tx_desc_dma, -+ ENETDMAC_RSTART, priv->tx_chan); -+ } - - /* clear remaining state ram for rx & tx channel */ -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ if (priv->dma_has_sram) { -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan); -+ } else { -+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->tx_chan); -+ } - - /* set max rx/tx length */ - enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG); -@@ -1017,18 +1042,24 @@ static int bcm_enet_open(struct net_devi - - /* set dma maximum burst len */ - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ ENETDMAC_MAXBURST, priv->rx_chan); - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ ENETDMAC_MAXBURST, priv->tx_chan); - - /* set correct transmit fifo watermark */ - enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG); - - /* set flow control low/high threshold to 1/3 / 2/3 */ -- val = priv->rx_ring_size / 3; -- enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -- val = (priv->rx_ring_size * 2) / 3; -- enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ if (priv->dma_has_sram) { -+ val = priv->rx_ring_size / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -+ val = (priv->rx_ring_size * 2) / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ } else { -+ enet_dmac_writel(priv, 5, ENETDMAC_FC, priv->rx_chan); -+ enet_dmac_writel(priv, priv->rx_ring_size, ENETDMAC_LEN, priv->rx_chan); -+ enet_dmac_writel(priv, priv->tx_ring_size, ENETDMAC_LEN, priv->tx_chan); -+ } - - /* all set, enable mac and interrupts, start dma engine and - * kick rx dma channel */ -@@ -1037,26 +1068,26 @@ static int bcm_enet_open(struct net_devi - val |= ENET_CTL_ENABLE_MASK; - enet_writel(priv, val, ENET_CTL_REG); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->rx_chan); - - /* watch "mib counters about to overflow" interrupt */ - enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); - enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); - - /* watch "packet transferred" interrupt in rx and tx */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->tx_chan); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->tx_chan); - - if (priv->has_phy) - phy_start(priv->phydev); -@@ -1136,13 +1167,13 @@ static void bcm_enet_disable_dma(struct - { - int limit; - -- enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG, chan); - - limit = 1000; - do { - u32 val; - -- val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan)); -+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG, chan); - if (!(val & ENETDMAC_CHANCFG_EN_MASK)) - break; - udelay(1); -@@ -1169,8 +1200,8 @@ static int bcm_enet_stop(struct net_devi - - /* mask all interrupts */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - /* make sure no mib update is scheduled */ - cancel_work_sync(&priv->mib_update_task); -@@ -1784,6 +1815,11 @@ static int bcm_enet_probe(struct platfor - priv->pause_tx = pd->pause_tx; - priv->force_duplex_full = pd->force_duplex_full; - priv->force_speed_100 = pd->force_speed_100; -+ priv->dma_chan_en_mask = pd->dma_chan_en_mask; -+ priv->dma_chan_int_mask = pd->dma_chan_int_mask; -+ priv->dma_chan_width = pd->dma_chan_width; -+ priv->dma_has_sram = pd->dma_has_sram; -+ priv->dma_desc_shift = pd->dma_desc_shift; - } - - if (priv->mac_id == 0 && priv->has_phy && !priv->use_external_mii) { -@@ -2121,8 +2157,8 @@ static int bcm_enetsw_open(struct net_de - kdev = &priv->pdev->dev; - - /* mask all interrupts and request them */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, - IRQF_DISABLED, dev->name, dev); -@@ -2234,23 +2270,23 @@ static int bcm_enetsw_open(struct net_de - - /* write rx & tx ring addresses */ - enet_dmas_writel(priv, priv->rx_desc_dma, -- ENETDMAS_RSTART_REG(priv->rx_chan)); -+ ENETDMAS_RSTART_REG, priv->rx_chan); - enet_dmas_writel(priv, priv->tx_desc_dma, -- ENETDMAS_RSTART_REG(priv->tx_chan)); -+ ENETDMAS_RSTART_REG, priv->tx_chan); - - /* clear remaining state ram for rx & tx channel */ -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan); - - /* set dma maximum burst len */ - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ ENETDMAC_MAXBURST, priv->rx_chan); - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ ENETDMAC_MAXBURST, priv->tx_chan); - - /* set flow control low/high threshold to 1/3 / 2/3 */ - val = priv->rx_ring_size / 3; -@@ -2264,21 +2300,21 @@ static int bcm_enetsw_open(struct net_de - wmb(); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); - enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ ENETDMAC_CHANCFG, priv->rx_chan); - - /* watch "packet transferred" interrupt in rx and tx */ - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -+ ENETDMAC_IR, priv->rx_chan); - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ ENETDMAC_IR, priv->tx_chan); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ ENETDMAC_IRMASK, priv->rx_chan); - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ ENETDMAC_IRMASK, priv->tx_chan); - - netif_carrier_on(dev); - netif_start_queue(dev); -@@ -2380,8 +2416,8 @@ static int bcm_enetsw_stop(struct net_de - del_timer_sync(&priv->rx_timeout); - - /* mask all interrupts */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - /* disable dma & mac */ - bcm_enet_disable_dma(priv, priv->tx_chan); -@@ -2715,6 +2751,10 @@ static int bcm_enetsw_probe(struct platf - memcpy(priv->used_ports, pd->used_ports, - sizeof(pd->used_ports)); - priv->num_ports = pd->num_ports; -+ priv->dma_has_sram = pd->dma_has_sram; -+ priv->dma_chan_en_mask = pd->dma_chan_en_mask; -+ priv->dma_chan_int_mask = pd->dma_chan_int_mask; -+ priv->dma_chan_width = pd->dma_chan_width; - } - - ret = compute_hw_mtu(priv, dev->mtu); ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -339,6 +339,21 @@ struct bcm_enet_priv { - /* used to poll switch port state */ - struct timer_list swphy_poll; - spinlock_t enetsw_mdio_lock; -+ -+ /* dma channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* dma channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* DMA engine has internal SRAM */ -+ bool dma_has_sram; -+ -+ /* dma channel width */ -+ unsigned int dma_chan_width; -+ -+ /* dma descriptor shift value */ -+ unsigned int dma_desc_shift; - }; - - diff --git a/target/linux/brcm63xx/patches-3.9/100-MIPS-bmips-fix-compilation-for-BMIPS5000.patch b/target/linux/brcm63xx/patches-3.9/100-MIPS-bmips-fix-compilation-for-BMIPS5000.patch deleted file mode 100644 index 6f4763420b..0000000000 --- a/target/linux/brcm63xx/patches-3.9/100-MIPS-bmips-fix-compilation-for-BMIPS5000.patch +++ /dev/null @@ -1,67 +0,0 @@ -From d55975b74389b2cf1a38732062ff89303940f6e1 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 29 Jun 2013 11:46:56 +0200 -Subject: [PATCH 01/10] MIPS: bmips: fix compilation for BMIPS5000 - -Replace the macro names in strings with actual macro invocation. - -Fixes the following build error: - - CC arch/mips/kernel/smp-bmips.o -{standard input}: Assembler messages: -{standard input}:951: Error: Unrecognized opcode `_ssnop' -{standard input}:952: Error: Unrecognized opcode `_ssnop' -(...) -make[6]: *** [arch/mips/kernel/smp-bmips.o] Error 1 - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/bmips.h | 28 ++++++++++++++-------------- - 1 file changed, 14 insertions(+), 14 deletions(-) - ---- a/arch/mips/include/asm/bmips.h -+++ b/arch/mips/include/asm/bmips.h -@@ -70,15 +70,15 @@ static inline unsigned long bmips_read_z - ".set noreorder\n" - "cache %1, 0(%2)\n" - "sync\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" - "mfc0 %0, $28, 3\n" -- "_ssnop\n" -+ __stringify(___ssnop) "\n" - ".set pop\n" - : "=&r" (ret) - : "i" (Index_Load_Tag_S), "r" (ZSCM_REG_BASE + offset) -@@ -92,13 +92,13 @@ static inline void bmips_write_zscm_reg( - ".set push\n" - ".set noreorder\n" - "mtc0 %0, $28, 3\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" - "cache %1, 0(%2)\n" -- "_ssnop\n" -- "_ssnop\n" -- "_ssnop\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" -+ __stringify(___ssnop) "\n" - : /* no outputs */ - : "r" (data), - "i" (Index_Store_Tag_S), "r" (ZSCM_REG_BASE + offset) diff --git a/target/linux/brcm63xx/patches-3.9/101-MIPS-allow-asm-cpu.h-to-be-included-from-assembly.patch b/target/linux/brcm63xx/patches-3.9/101-MIPS-allow-asm-cpu.h-to-be-included-from-assembly.patch deleted file mode 100644 index 27c3b9eea5..0000000000 --- a/target/linux/brcm63xx/patches-3.9/101-MIPS-allow-asm-cpu.h-to-be-included-from-assembly.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 520f4bf75026cc60ba47946331966fb670b39cb0 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 27 Jun 2013 21:32:41 +0200 -Subject: [PATCH 02/10] MIPS: allow asm/cpu.h to be included from assembly - -Add guards around the enum to allow including cpu.h from assembly. - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/cpu.h | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/arch/mips/include/asm/cpu.h -+++ b/arch/mips/include/asm/cpu.h -@@ -225,6 +225,8 @@ - - #define FPIR_IMP_NONE 0x0000 - -+#if !defined(__ASSEMBLY__) -+ - enum cpu_type_enum { - CPU_UNKNOWN, - -@@ -277,6 +279,7 @@ enum cpu_type_enum { - CPU_LAST - }; - -+#endif /* !__ASSEMBLY */ - - /* - * ISA Level encodings diff --git a/target/linux/brcm63xx/patches-3.9/102-MIPS-bmips-add-macros-for-testing-the-current-bmips-.patch b/target/linux/brcm63xx/patches-3.9/102-MIPS-bmips-add-macros-for-testing-the-current-bmips-.patch deleted file mode 100644 index af38b35689..0000000000 --- a/target/linux/brcm63xx/patches-3.9/102-MIPS-bmips-add-macros-for-testing-the-current-bmips-.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 971b8b3d5101b3bb868e63f3eb96fe69b7110c61 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 27 Jun 2013 12:40:15 +0200 -Subject: [PATCH 03/10] MIPS: bmips: add macros for testing the current bmips - CPU - -Makes it easy to make code conditionally compiled for supported CPUs -without directly relying on #ifdefs. - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/bmips.h | 11 +++++++++++ - 1 file changed, 11 insertions(+) - ---- a/arch/mips/include/asm/bmips.h -+++ b/arch/mips/include/asm/bmips.h -@@ -45,8 +45,19 @@ - #if !defined(__ASSEMBLY__) - - #include -+#include - #include - -+#define cpu_is_bmips32() (current_cpu_type() == CPU_BMIPS32) -+#define cpu_is_bmips3300() (IS_ENABLED(CONFIG_CPU_BMIPS3300) && \ -+ current_cpu_type() == CPU_BMIPS3300) -+#define cpu_is_bmips4350() (IS_ENABLED(CONFIG_CPU_BMIPS4350) && \ -+ current_cpu_type() == CPU_BMIPS4350) -+#define cpu_is_bmips4380() (IS_ENABLED(CONFIG_CPU_BMIPS4380) && \ -+ current_cpu_type() == CPU_BMIPS4380) -+#define cpu_is_bmips5000() (IS_ENABLED(CONFIG_CPU_BMIPS5000) && \ -+ current_cpu_type() == CPU_BMIPS5000) -+ - extern struct plat_smp_ops bmips_smp_ops; - extern char bmips_reset_nmi_vec; - extern char bmips_reset_nmi_vec_end; diff --git a/target/linux/brcm63xx/patches-3.9/103-MIPS-bmips-change-compile-time-checks-to-runtime-che.patch b/target/linux/brcm63xx/patches-3.9/103-MIPS-bmips-change-compile-time-checks-to-runtime-che.patch deleted file mode 100644 index d55189529e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/103-MIPS-bmips-change-compile-time-checks-to-runtime-che.patch +++ /dev/null @@ -1,482 +0,0 @@ -From 12594762fcbec024cb424c9b77efb28402651667 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 27 Jun 2013 21:33:56 +0200 -Subject: [PATCH 04/10] MIPS: bmips: change compile time checks to runtime - checks - -Allow building for all bmips cpus at the same time by changing ifdefs -to checks for the cpu type, or adding appropriate checks to the -assembly. - -Signed-off-by: Jonas Gorski ---- - arch/mips/kernel/bmips_vec.S | 55 +++++++--- - arch/mips/kernel/smp-bmips.c | 241 ++++++++++++++++++++++-------------------- - 2 files changed, 172 insertions(+), 124 deletions(-) - ---- a/arch/mips/kernel/bmips_vec.S -+++ b/arch/mips/kernel/bmips_vec.S -@@ -13,6 +13,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -89,12 +90,18 @@ NESTED(bmips_reset_nmi_vec, PT_SIZE, sp) - beqz k0, bmips_smp_entry - - #if defined(CONFIG_CPU_BMIPS5000) -+ mfc0 k0, CP0_PRID -+ li k1, PRID_IMP_BMIPS5000 -+ andi k0, 0xff00 -+ bne k0, k1, 1f -+ - /* if we're not on core 0, this must be the SMP boot signal */ - li k1, (3 << 25) - mfc0 k0, $22 - and k0, k1 - bnez k0, bmips_smp_entry --#endif -+1: -+#endif /* CONFIG_CPU_BMIPS5000 */ - #endif /* CONFIG_SMP */ - - /* nope, it's just a regular NMI */ -@@ -137,7 +144,12 @@ bmips_smp_entry: - xori k0, 0x04 - mtc0 k0, CP0_CONFIG - -+ mfc0 k0, CP0_PRID -+ andi k0, 0xff00 - #if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) -+ li k1, PRID_IMP_BMIPS43XX -+ bne k0, k1, 2f -+ - /* initialize CPU1's local I-cache */ - li k0, 0x80000000 - li k1, 0x80010000 -@@ -148,14 +160,21 @@ bmips_smp_entry: - 1: cache Index_Store_Tag_I, 0(k0) - addiu k0, 16 - bne k0, k1, 1b --#elif defined(CONFIG_CPU_BMIPS5000) -+ -+ b 3f -+2: -+#endif /* CONFIG_CPU_BMIPS4350 || CONFIG_CPU_BMIPS4380 */ -+#if defined(CONFIG_CPU_BMIPS5000) - /* set exception vector base */ -+ li k1, PRID_IMP_BMIPS5000 -+ bne k0, k1, 3f -+ - la k0, ebase - lw k0, 0(k0) - mtc0 k0, $15, 1 - BARRIER --#endif -- -+#endif /* CONFIG_CPU_BMIPS5000 */ -+3: - /* jump back to kseg0 in case we need to remap the kseg1 area */ - la k0, 1f - jr k0 -@@ -221,8 +240,18 @@ END(bmips_smp_int_vec) - LEAF(bmips_enable_xks01) - - #if defined(CONFIG_XKS01) -- -+ mfc0 t0, CP0_PRID -+ andi t2, t0, 0xff00 - #if defined(CONFIG_CPU_BMIPS4380) -+ li t1, PRID_IMP_BMIPS43XX -+ bne t2, t1, 1f -+ -+ andi t0, 0xff -+ addiu t1, t0, -PRID_REV_BMIPS4380_HI -+ bgtz t1, 2f -+ addiu t0, -PRID_REV_BMIPS4380_LO -+ bltz t0, 2f -+ - mfc0 t0, $22, 3 - li t1, 0x1ff0 - li t2, (1 << 12) | (1 << 9) -@@ -231,7 +260,13 @@ LEAF(bmips_enable_xks01) - or t0, t2 - mtc0 t0, $22, 3 - BARRIER --#elif defined(CONFIG_CPU_BMIPS5000) -+ b 2f -+1: -+#endif /* CONFIG_CPU_BMIPS4380 */ -+#if defined(CONFIG_CPU_BMIPS5000) -+ li t1, PRID_IMP_BMIPS5000 -+ bne t2, t1, 2f -+ - mfc0 t0, $22, 5 - li t1, 0x01ff - li t2, (1 << 8) | (1 << 5) -@@ -240,12 +275,8 @@ LEAF(bmips_enable_xks01) - or t0, t2 - mtc0 t0, $22, 5 - BARRIER --#else -- --#error Missing XKS01 setup -- --#endif -- -+#endif /* CONFIG_CPU_BMIPS5000 */ -+2: - #endif /* defined(CONFIG_XKS01) */ - - jr ra ---- a/arch/mips/kernel/smp-bmips.c -+++ b/arch/mips/kernel/smp-bmips.c -@@ -49,8 +49,11 @@ cpumask_t bmips_booted_mask; - unsigned long bmips_smp_boot_sp; - unsigned long bmips_smp_boot_gp; - -+static void bmips43xx_send_ipi_single(int cpu, unsigned int action); -+static void bmips5000_send_ipi_single(int cpu, unsigned int action); - static void bmips_send_ipi_single(int cpu, unsigned int action); --static irqreturn_t bmips_ipi_interrupt(int irq, void *dev_id); -+static irqreturn_t bmips43xx_ipi_interrupt(int irq, void *dev_id); -+static irqreturn_t bmips5000_ipi_interrupt(int irq, void *dev_id); - - /* SW interrupts 0,1 are used for interprocessor signaling */ - #define IPI0_IRQ (MIPS_CPU_IRQ_BASE + 0) -@@ -65,48 +68,49 @@ static void __init bmips_smp_setup(void) - { - int i, cpu = 1, boot_cpu = 0; - --#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) -- /* arbitration priority */ -- clear_c0_brcm_cmt_ctrl(0x30); -- -- /* NBK and weak order flags */ -- set_c0_brcm_config_0(0x30000); -- -- /* Find out if we are running on TP0 or TP1 */ -- boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31)); -- -- /* -- * MIPS interrupts 0,1 (SW INT 0,1) cross over to the other thread -- * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output -- * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output -- * -- * If booting from TP1, leave the existing CMT interrupt routing -- * such that TP0 responds to SW1 and TP1 responds to SW0. -- */ -- if (boot_cpu == 0) -- change_c0_brcm_cmt_intr(0xf8018000, -+ if (cpu_is_bmips4350() || cpu_is_bmips4380()) { -+ /* arbitration priority */ -+ clear_c0_brcm_cmt_ctrl(0x30); -+ -+ /* NBK and weak order flags */ -+ set_c0_brcm_config_0(0x30000); -+ -+ /* Find out if we are running on TP0 or TP1 */ -+ boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31)); -+ -+ /* -+ * MIPS interrupts 0,1 (SW INT 0,1) cross over to the other -+ * thread -+ * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output -+ * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output -+ * -+ * If booting from TP1, leave the existing CMT interrupt routing -+ * such that TP0 responds to SW1 and TP1 responds to SW0. -+ */ -+ if (boot_cpu == 0) -+ change_c0_brcm_cmt_intr(0xf8018000, - (0x02 << 27) | (0x03 << 15)); -- else -- change_c0_brcm_cmt_intr(0xf8018000, (0x1d << 27)); -- -- /* single core, 2 threads (2 pipelines) */ -- max_cpus = 2; --#elif defined(CONFIG_CPU_BMIPS5000) -- /* enable raceless SW interrupts */ -- set_c0_brcm_config(0x03 << 22); -- -- /* route HW interrupt 0 to CPU0, HW interrupt 1 to CPU1 */ -- change_c0_brcm_mode(0x1f << 27, 0x02 << 27); -+ else -+ change_c0_brcm_cmt_intr(0xf8018000, (0x1d << 27)); - -- /* N cores, 2 threads per core */ -- max_cpus = (((read_c0_brcm_config() >> 6) & 0x03) + 1) << 1; -- -- /* clear any pending SW interrupts */ -- for (i = 0; i < max_cpus; i++) { -- write_c0_brcm_action(ACTION_CLR_IPI(i, 0)); -- write_c0_brcm_action(ACTION_CLR_IPI(i, 1)); -+ /* single core, 2 threads (2 pipelines) */ -+ max_cpus = 2; -+ } else if (cpu_is_bmips5000()) { -+ /* enable raceless SW interrupts */ -+ set_c0_brcm_config(0x03 << 22); -+ -+ /* route HW interrupt 0 to CPU0, HW interrupt 1 to CPU1 */ -+ change_c0_brcm_mode(0x1f << 27, 0x02 << 27); -+ -+ /* N cores, 2 threads per core */ -+ max_cpus = (((read_c0_brcm_config() >> 6) & 0x03) + 1) << 1; -+ -+ /* clear any pending SW interrupts */ -+ for (i = 0; i < max_cpus; i++) { -+ write_c0_brcm_action(ACTION_CLR_IPI(i, 0)); -+ write_c0_brcm_action(ACTION_CLR_IPI(i, 1)); -+ } - } --#endif - - if (!bmips_smp_enabled) - max_cpus = 1; -@@ -134,6 +138,15 @@ static void __init bmips_smp_setup(void) - */ - static void bmips_prepare_cpus(unsigned int max_cpus) - { -+ irqreturn_t (*bmips_ipi_interrupt)(int irq, void *dev_id); -+ -+ if (cpu_is_bmips4350() || cpu_is_bmips4380()) -+ bmips_ipi_interrupt = bmips43xx_ipi_interrupt; -+ else if (cpu_is_bmips5000()) -+ bmips_ipi_interrupt = bmips5000_ipi_interrupt; -+ else -+ return; -+ - if (request_irq(IPI0_IRQ, bmips_ipi_interrupt, IRQF_PERCPU, - "smp_ipi0", NULL)) - panic("Can't request IPI0 interrupt\n"); -@@ -168,26 +181,26 @@ static void bmips_boot_secondary(int cpu - - pr_info("SMP: Booting CPU%d...\n", cpu); - -- if (cpumask_test_cpu(cpu, &bmips_booted_mask)) -+ if (cpumask_test_cpu(cpu, &bmips_booted_mask)) { - bmips_send_ipi_single(cpu, 0); -- else { --#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) -- /* Reset slave TP1 if booting from TP0 */ -- if (cpu_logical_map(cpu) == 0) -- set_c0_brcm_cmt_ctrl(0x01); --#elif defined(CONFIG_CPU_BMIPS5000) -- if (cpu & 0x01) -- write_c0_brcm_action(ACTION_BOOT_THREAD(cpu)); -- else { -- /* -- * core N thread 0 was already booted; just -- * pulse the NMI line -- */ -- bmips_write_zscm_reg(0x210, 0xc0000000); -- udelay(10); -- bmips_write_zscm_reg(0x210, 0x00); -+ } else { -+ if (cpu_is_bmips4350() || cpu_is_bmips4380()) { -+ /* Reset slave TP1 if booting from TP0 */ -+ if (cpu_logical_map(cpu) == 0) -+ set_c0_brcm_cmt_ctrl(0x01); -+ } else if (cpu_is_bmips5000()) { -+ if (cpu & 0x01) -+ write_c0_brcm_action(ACTION_BOOT_THREAD(cpu)); -+ else { -+ /* -+ * core N thread 0 was already booted; just -+ * pulse the NMI line -+ */ -+ bmips_write_zscm_reg(0x210, 0xc0000000); -+ udelay(10); -+ bmips_write_zscm_reg(0x210, 0x00); -+ } - } --#endif - cpumask_set_cpu(cpu, &bmips_booted_mask); - } - } -@@ -199,20 +212,21 @@ static void bmips_init_secondary(void) - { - /* move NMI vector to kseg0, in case XKS01 is enabled */ - --#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380) -- void __iomem *cbr = BMIPS_GET_CBR(); -- unsigned long old_vec; -- -- old_vec = __raw_readl(cbr + BMIPS_RELO_VECTOR_CONTROL_1); -- __raw_writel(old_vec & ~0x20000000, cbr + BMIPS_RELO_VECTOR_CONTROL_1); -- -- clear_c0_cause(smp_processor_id() ? C_SW1 : C_SW0); --#elif defined(CONFIG_CPU_BMIPS5000) -- write_c0_brcm_bootvec(read_c0_brcm_bootvec() & -- (smp_processor_id() & 0x01 ? ~0x20000000 : ~0x2000)); -+ if (cpu_is_bmips4350() || cpu_is_bmips4380()) { -+ void __iomem *cbr = BMIPS_GET_CBR(); -+ unsigned long old_vec; -+ -+ old_vec = __raw_readl(cbr + BMIPS_RELO_VECTOR_CONTROL_1); -+ __raw_writel(old_vec & ~0x20000000, -+ cbr + BMIPS_RELO_VECTOR_CONTROL_1); -+ -+ clear_c0_cause(smp_processor_id() ? C_SW1 : C_SW0); -+ } else if (cpu_is_bmips5000()) { -+ write_c0_brcm_bootvec(read_c0_brcm_bootvec() & -+ (smp_processor_id() & 0x01 ? ~0x20000000 : ~0x2000)); - -- write_c0_brcm_action(ACTION_CLR_IPI(smp_processor_id(), 0)); --#endif -+ write_c0_brcm_action(ACTION_CLR_IPI(smp_processor_id(), 0)); -+ } - } - - /* -@@ -237,8 +251,6 @@ static void bmips_cpus_done(void) - { - } - --#if defined(CONFIG_CPU_BMIPS5000) -- - /* - * BMIPS5000 raceless IPIs - * -@@ -247,12 +259,12 @@ static void bmips_cpus_done(void) - * IPI1 is used for SMP_CALL_FUNCTION - */ - --static void bmips_send_ipi_single(int cpu, unsigned int action) -+static void bmips5000_send_ipi_single(int cpu, unsigned int action) - { - write_c0_brcm_action(ACTION_SET_IPI(cpu, action == SMP_CALL_FUNCTION)); - } - --static irqreturn_t bmips_ipi_interrupt(int irq, void *dev_id) -+static irqreturn_t bmips5000_ipi_interrupt(int irq, void *dev_id) - { - int action = irq - IPI0_IRQ; - -@@ -266,8 +278,6 @@ static irqreturn_t bmips_ipi_interrupt(i - return IRQ_HANDLED; - } - --#else -- - /* - * BMIPS43xx racey IPIs - * -@@ -281,7 +291,7 @@ static irqreturn_t bmips_ipi_interrupt(i - static DEFINE_SPINLOCK(ipi_lock); - static DEFINE_PER_CPU(int, ipi_action_mask); - --static void bmips_send_ipi_single(int cpu, unsigned int action) -+static void bmips43xx_send_ipi_single(int cpu, unsigned int action) - { - unsigned long flags; - -@@ -292,7 +302,7 @@ static void bmips_send_ipi_single(int cp - spin_unlock_irqrestore(&ipi_lock, flags); - } - --static irqreturn_t bmips_ipi_interrupt(int irq, void *dev_id) -+static irqreturn_t bmips43xx_ipi_interrupt(int irq, void *dev_id) - { - unsigned long flags; - int action, cpu = irq - IPI0_IRQ; -@@ -311,7 +321,13 @@ static irqreturn_t bmips_ipi_interrupt(i - return IRQ_HANDLED; - } - --#endif /* BMIPS type */ -+static void bmips_send_ipi_single(int cpu, unsigned int action) -+{ -+ if (cpu_is_bmips4350() || cpu_is_bmips4380()) -+ bmips43xx_send_ipi_single(cpu, action); -+ else if (cpu_is_bmips5000()) -+ bmips5000_send_ipi_single(cpu, action); -+} - - static void bmips_send_ipi_mask(const struct cpumask *mask, - unsigned int action) -@@ -421,43 +437,44 @@ void __cpuinit bmips_ebase_setup(void) - - BUG_ON(ebase != CKSEG0); - --#if defined(CONFIG_CPU_BMIPS4350) -- /* -- * BMIPS4350 cannot relocate the normal vectors, but it -- * can relocate the BEV=1 vectors. So CPU1 starts up at -- * the relocated BEV=1, IV=0 general exception vector @ -- * 0xa000_0380. -- * -- * set_uncached_handler() is used here because: -- * - CPU1 will run this from uncached space -- * - None of the cacheflush functions are set up yet -- */ -- set_uncached_handler(BMIPS_WARM_RESTART_VEC - CKSEG0, -- &bmips_smp_int_vec, 0x80); -- __sync(); -- return; --#elif defined(CONFIG_CPU_BMIPS4380) -- /* -- * 0x8000_0000: reset/NMI (initially in kseg1) -- * 0x8000_0400: normal vectors -- */ -- new_ebase = 0x80000400; -- cbr = BMIPS_GET_CBR(); -- __raw_writel(0x80080800, cbr + BMIPS_RELO_VECTOR_CONTROL_0); -- __raw_writel(0xa0080800, cbr + BMIPS_RELO_VECTOR_CONTROL_1); --#elif defined(CONFIG_CPU_BMIPS5000) -- /* -- * 0x8000_0000: reset/NMI (initially in kseg1) -- * 0x8000_1000: normal vectors -- */ -- new_ebase = 0x80001000; -- write_c0_brcm_bootvec(0xa0088008); -- write_c0_ebase(new_ebase); -- if (max_cpus > 2) -- bmips_write_zscm_reg(0xa0, 0xa008a008); --#else -- return; --#endif -+ if (cpu_is_bmips4350()) { -+ /* -+ * BMIPS4350 cannot relocate the normal vectors, but it -+ * can relocate the BEV=1 vectors. So CPU1 starts up at -+ * the relocated BEV=1, IV=0 general exception vector @ -+ * 0xa000_0380. -+ * -+ * set_uncached_handler() is used here because: -+ * - CPU1 will run this from uncached space -+ * - None of the cacheflush functions are set up yet -+ */ -+ set_uncached_handler(BMIPS_WARM_RESTART_VEC - CKSEG0, -+ &bmips_smp_int_vec, 0x80); -+ __sync(); -+ return; -+ } else if (cpu_is_bmips4380()) { -+ /* -+ * 0x8000_0000: reset/NMI (initially in kseg1) -+ * 0x8000_0400: normal vectors -+ */ -+ new_ebase = 0x80000400; -+ cbr = BMIPS_GET_CBR(); -+ __raw_writel(0x80080800, cbr + BMIPS_RELO_VECTOR_CONTROL_0); -+ __raw_writel(0xa0080800, cbr + BMIPS_RELO_VECTOR_CONTROL_1); -+ } else if (cpu_is_bmips5000()) { -+ /* -+ * 0x8000_0000: reset/NMI (initially in kseg1) -+ * 0x8000_1000: normal vectors -+ */ -+ new_ebase = 0x80001000; -+ write_c0_brcm_bootvec(0xa0088008); -+ write_c0_ebase(new_ebase); -+ if (max_cpus > 2) -+ bmips_write_zscm_reg(0xa0, 0xa008a008); -+ } else { -+ return; -+ } -+ - board_nmi_handler_setup = &bmips_nmi_handler_setup; - ebase = new_ebase; - } diff --git a/target/linux/brcm63xx/patches-3.9/104-MIPS-bmips-merge-CPU-options-into-one-option.patch b/target/linux/brcm63xx/patches-3.9/104-MIPS-bmips-merge-CPU-options-into-one-option.patch deleted file mode 100644 index 386c63c1ae..0000000000 --- a/target/linux/brcm63xx/patches-3.9/104-MIPS-bmips-merge-CPU-options-into-one-option.patch +++ /dev/null @@ -1,126 +0,0 @@ -From 1ecac776e6c652e3059d4f4d9dd8369e89ebef81 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 27 Jun 2013 23:57:20 +0200 -Subject: [PATCH 05/10] MIPS: bmips: merge CPU options into one option - -Instead of treating each flavour as an exclusive CPU to select, make -BMIPS the only option and let SYS_HAS_CPU_BMIPS* decide for which -flavours to include support. - -Run tested on BMIPS3300 and BMIPS4350, only build tested for BMIPS4380 -and BMISP5000. - -Signed-off-by: Jonas Gorski ---- - arch/mips/Kconfig | 77 +++++++++++++++++++++++++---------------------------- - 1 file changed, 36 insertions(+), 41 deletions(-) - ---- a/arch/mips/Kconfig -+++ b/arch/mips/Kconfig -@@ -130,6 +130,7 @@ config BCM63XX - select DMA_NONCOHERENT - select IRQ_CPU - select SYS_HAS_CPU_MIPS32_R1 -+ select SYS_HAS_CPU_BMIPS - select SYS_HAS_CPU_BMIPS4350 if !BCM63XX_CPU_6338 && !BCM63XX_CPU_6345 && !BCM63XX_CPU_6348 - select NR_CPUS_DEFAULT_2 - select SYS_SUPPORTS_32BIT_KERNEL -@@ -1454,41 +1455,21 @@ config CPU_CAVIUM_OCTEON - can have up to 16 Mips64v2 cores and 8 integrated gigabit ethernets. - Full details can be found at http://www.caviumnetworks.com. - --config CPU_BMIPS3300 -- bool "BMIPS3300" -- depends on SYS_HAS_CPU_BMIPS3300 -- select CPU_BMIPS -- help -- Broadcom BMIPS3300 processors. -- --config CPU_BMIPS4350 -- bool "BMIPS4350" -- depends on SYS_HAS_CPU_BMIPS4350 -- select CPU_BMIPS -- select SYS_SUPPORTS_SMP -- select SYS_SUPPORTS_HOTPLUG_CPU -- help -- Broadcom BMIPS4350 ("VIPER") processors. -- --config CPU_BMIPS4380 -- bool "BMIPS4380" -- depends on SYS_HAS_CPU_BMIPS4380 -- select CPU_BMIPS -- select SYS_SUPPORTS_SMP -- select SYS_SUPPORTS_HOTPLUG_CPU -- help -- Broadcom BMIPS4380 processors. -- --config CPU_BMIPS5000 -- bool "BMIPS5000" -- depends on SYS_HAS_CPU_BMIPS5000 -- select CPU_BMIPS -- select CPU_SUPPORTS_HIGHMEM -- select MIPS_CPU_SCACHE -- select SYS_SUPPORTS_SMP -- select SYS_SUPPORTS_HOTPLUG_CPU -+config CPU_BMIPS -+ bool "Broadcom BMIPS" -+ depends on SYS_HAS_CPU_BMIPS -+ select CPU_MIPS32 -+ select CPU_BMIPS3300 if SYS_HAS_CPU_BMIPS3300 -+ select CPU_BMIPS4350 if SYS_HAS_CPU_BMIPS4350 -+ select CPU_BMIPS4350 if SYS_HAS_CPU_BMIPS4380 -+ select CPU_BMIPS5000 if SYS_HAS_CPU_BMIPS5000 -+ select CPU_SUPPORTS_32BIT_KERNEL -+ select DMA_NONCOHERENT -+ select IRQ_CPU -+ select SWAP_IO_SPACE -+ select WEAK_ORDERING - help -- Broadcom BMIPS5000 processors. -+ Support for BMIPS3300/4350/4380 and BMIPS5000 processors. - - config CPU_XLR - bool "Netlogic XLR SoC" -@@ -1569,14 +1550,25 @@ config CPU_LOONGSON1 - select CPU_SUPPORTS_32BIT_KERNEL - select CPU_SUPPORTS_HIGHMEM - --config CPU_BMIPS -+config CPU_BMIPS3300 - bool -- select CPU_MIPS32 -- select CPU_SUPPORTS_32BIT_KERNEL -- select DMA_NONCOHERENT -- select IRQ_CPU -- select SWAP_IO_SPACE -- select WEAK_ORDERING -+ -+config CPU_BMIPS4350 -+ bool -+ select SYS_SUPPORTS_SMP -+ select SYS_SUPPORTS_HOTPLUG_CPU -+ -+config CPU_BMIPS4380 -+ bool -+ select SYS_SUPPORTS_SMP -+ select SYS_SUPPORTS_HOTPLUG_CPU -+ -+config CPU_BMIPS5000 -+ bool -+ select CPU_SUPPORTS_HIGHMEM -+ select MIPS_CPU_SCACHE -+ select SYS_SUPPORTS_SMP -+ select SYS_SUPPORTS_HOTPLUG_CPU - - config SYS_HAS_CPU_LOONGSON2E - bool -@@ -1650,6 +1642,9 @@ config SYS_HAS_CPU_SB1 - config SYS_HAS_CPU_CAVIUM_OCTEON - bool - -+config SYS_HAS_CPU_BMIPS -+ bool -+ - config SYS_HAS_CPU_BMIPS3300 - bool - diff --git a/target/linux/brcm63xx/patches-3.9/105-MIPS-BCM63XX-let-the-individual-SoCs-select-the-appr.patch b/target/linux/brcm63xx/patches-3.9/105-MIPS-BCM63XX-let-the-individual-SoCs-select-the-appr.patch deleted file mode 100644 index cb09abcc2d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/105-MIPS-BCM63XX-let-the-individual-SoCs-select-the-appr.patch +++ /dev/null @@ -1,72 +0,0 @@ -From 9d1e9d7abd2f2d067169fb0c62e34cf080bbd7a1 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 23 Jun 2013 12:25:49 +0200 -Subject: [PATCH 06/10] MIPS: BCM63XX: let the individual SoCs select the - appropriate CPUs - -Let each supported chip select the appropirate SYS_HAS_CPU_BMIPS* -option for its embedded processor, so support will be conditionally -included. - -Signed-off-by: Jonas Gorski - -fix bmips selection ---- - arch/mips/Kconfig | 1 - - arch/mips/bcm63xx/Kconfig | 8 ++++++++ - 2 files changed, 8 insertions(+), 1 deletion(-) - ---- a/arch/mips/Kconfig -+++ b/arch/mips/Kconfig -@@ -131,7 +131,6 @@ config BCM63XX - select IRQ_CPU - select SYS_HAS_CPU_MIPS32_R1 - select SYS_HAS_CPU_BMIPS -- select SYS_HAS_CPU_BMIPS4350 if !BCM63XX_CPU_6338 && !BCM63XX_CPU_6345 && !BCM63XX_CPU_6348 - select NR_CPUS_DEFAULT_2 - select SYS_SUPPORTS_32BIT_KERNEL - select SYS_SUPPORTS_BIG_ENDIAN ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -3,33 +3,41 @@ menu "CPU support" - - config BCM63XX_CPU_3368 - bool "support 3368 CPU" -+ select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - - config BCM63XX_CPU_6328 - bool "support 6328 CPU" -+ select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - - config BCM63XX_CPU_6338 - bool "support 6338 CPU" -+ select SYS_HAS_CPU_BMIPS3300 - select HW_HAS_PCI - - config BCM63XX_CPU_6345 - bool "support 6345 CPU" -+ select SYS_HAS_CPU_BMIPS3300 - - config BCM63XX_CPU_6348 - bool "support 6348 CPU" -+ select SYS_HAS_CPU_BMIPS3300 - select HW_HAS_PCI - - config BCM63XX_CPU_6358 - bool "support 6358 CPU" -+ select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - - config BCM63XX_CPU_6362 - bool "support 6362 CPU" -+ select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - - config BCM63XX_CPU_6368 - bool "support 6368 CPU" -+ select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - endmenu - diff --git a/target/linux/brcm63xx/patches-3.9/106-MIPS-bmips-add-a-helper-function-for-registering-smp.patch b/target/linux/brcm63xx/patches-3.9/106-MIPS-bmips-add-a-helper-function-for-registering-smp.patch deleted file mode 100644 index ad357b6ab2..0000000000 --- a/target/linux/brcm63xx/patches-3.9/106-MIPS-bmips-add-a-helper-function-for-registering-smp.patch +++ /dev/null @@ -1,42 +0,0 @@ -From aa15ac91faccc3bf01a29670b1f9ae1945cea056 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 23 Jun 2013 14:04:51 +0200 -Subject: [PATCH 07/10] MIPS: bmips: add a helper function for registering smp - ops - -Add a helper similar to the generic register_XXX_smp_ops() for bmips. - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/bmips.h | 13 +++++++++++++ - 1 file changed, 13 insertions(+) - ---- a/arch/mips/include/asm/bmips.h -+++ b/arch/mips/include/asm/bmips.h -@@ -47,6 +47,7 @@ - #include - #include - #include -+#include - - #define cpu_is_bmips32() (current_cpu_type() == CPU_BMIPS32) - #define cpu_is_bmips3300() (IS_ENABLED(CONFIG_CPU_BMIPS3300) && \ -@@ -59,6 +60,18 @@ - current_cpu_type() == CPU_BMIPS5000) - - extern struct plat_smp_ops bmips_smp_ops; -+ -+static inline int register_bmips_smp_ops(void) -+{ -+#ifdef CONFIG_CPU_BMIPS -+ register_smp_ops(&bmips_smp_ops); -+ -+ return 0; -+#else -+ return -ENODEV; -+#endif -+} -+ - extern char bmips_reset_nmi_vec; - extern char bmips_reset_nmi_vec_end; - extern char bmips_smp_movevec; diff --git a/target/linux/brcm63xx/patches-3.9/107-MIPS-BCM63XX-always-register-bmips-smp-ops.patch b/target/linux/brcm63xx/patches-3.9/107-MIPS-BCM63XX-always-register-bmips-smp-ops.patch deleted file mode 100644 index 1ea52c478c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/107-MIPS-BCM63XX-always-register-bmips-smp-ops.patch +++ /dev/null @@ -1,26 +0,0 @@ -From c489eace9492d1b8bedb314bdef169e719161bff Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 28 Jun 2013 00:08:16 +0200 -Subject: [PATCH 08/10] MIPS: BCM63XX: always register bmips smp ops - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/prom.c | 6 +++--- - 1 file changed, 3 insertions(+), 3 deletions(-) - ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -59,10 +59,10 @@ void __init prom_init(void) - /* do low level board init */ - board_prom_init(); - -- if (IS_ENABLED(CONFIG_CPU_BMIPS4350) && IS_ENABLED(CONFIG_SMP)) { -- /* set up SMP */ -- register_smp_ops(&bmips_smp_ops); -+ /* set up SMP */ -+ register_bmips_smp_ops(); - -+ if (IS_ENABLED(CONFIG_CPU_BMIPS4350) && IS_ENABLED(CONFIG_SMP)) { - /* - * BCM6328 might not have its second CPU enabled, while BCM6358 - * needs special handling for its shared TLB, so disable SMP diff --git a/target/linux/brcm63xx/patches-3.9/108-MIPS-BCM63XX-change-the-guard-to-a-BMIPS4350-check.patch b/target/linux/brcm63xx/patches-3.9/108-MIPS-BCM63XX-change-the-guard-to-a-BMIPS4350-check.patch deleted file mode 100644 index 75729858eb..0000000000 --- a/target/linux/brcm63xx/patches-3.9/108-MIPS-BCM63XX-change-the-guard-to-a-BMIPS4350-check.patch +++ /dev/null @@ -1,21 +0,0 @@ -From 3a862fd3cc4f477ad2232370abfceca1ec2145ae Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 28 Jun 2013 00:10:07 +0200 -Subject: [PATCH 09/10] MIPS: BCM63XX: change the guard to a BMIPS4350 check - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/prom.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -62,7 +62,7 @@ void __init prom_init(void) - /* set up SMP */ - register_bmips_smp_ops(); - -- if (IS_ENABLED(CONFIG_CPU_BMIPS4350) && IS_ENABLED(CONFIG_SMP)) { -+ if (cpu_is_bmips4350()) { - /* - * BCM6328 might not have its second CPU enabled, while BCM6358 - * needs special handling for its shared TLB, so disable SMP diff --git a/target/linux/brcm63xx/patches-3.9/109-MIPS-BCM63XX-disable-SMP-also-on-BCM3368.patch b/target/linux/brcm63xx/patches-3.9/109-MIPS-BCM63XX-disable-SMP-also-on-BCM3368.patch deleted file mode 100644 index dbb2ae4e34..0000000000 --- a/target/linux/brcm63xx/patches-3.9/109-MIPS-BCM63XX-disable-SMP-also-on-BCM3368.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 32d4b03c0aedb96022e86a67a560f6eaf488200a Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 28 Jun 2013 00:25:13 +0200 -Subject: [PATCH 10/10] MIPS: BCM63XX: disable SMP also on BCM3368 - -BCM3368 has the same shared TLB as BCM6358. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/prom.c | 8 ++++---- - 1 file changed, 4 insertions(+), 4 deletions(-) - ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -64,9 +64,9 @@ void __init prom_init(void) - - if (cpu_is_bmips4350()) { - /* -- * BCM6328 might not have its second CPU enabled, while BCM6358 -- * needs special handling for its shared TLB, so disable SMP -- * for now. -+ * BCM6328 might not have its second CPU enabled, while BCM3368 -+ * and BCM6358 need special handling for their shared TLB, so -+ * disable SMP for now. - */ - if (BCMCPU_IS_6328()) { - reg = bcm_readl(BCM_6328_OTP_BASE + -@@ -74,7 +74,7 @@ void __init prom_init(void) - - if (reg & OTP_6328_REG3_TP1_DISABLED) - bmips_smp_enabled = 0; -- } else if (BCMCPU_IS_6358()) { -+ } else if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) { - bmips_smp_enabled = 0; - } - diff --git a/target/linux/brcm63xx/patches-3.9/110-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch b/target/linux/brcm63xx/patches-3.9/110-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch deleted file mode 100644 index 63d385be4e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/110-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 80a2f983e9f44dbc3e01ae31c62d877846a7f791 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:19 +0100 -Subject: [PATCH 01/11] MIPS: BCM63XX: add USB host clock enable delay - -Knowledge of the clock setup delay should remain at the clock level (so -it can be clock specific and CPU specific). Add the 100 milliseconds -required clock delay for the USB host clock when it gets enabled. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/clk.c | 5 +++++ - 1 file changed, 5 insertions(+) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -177,6 +177,11 @@ static void usbh_set(struct clk *clk, in - bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); - else if (BCMCPU_IS_6368()) - bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); -+ else -+ return; -+ -+ if (enable) -+ msleep(100); - } - - static struct clk clk_usbh = { diff --git a/target/linux/brcm63xx/patches-3.9/111-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch b/target/linux/brcm63xx/patches-3.9/111-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch deleted file mode 100644 index eaf75030f0..0000000000 --- a/target/linux/brcm63xx/patches-3.9/111-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 8e9bf528a122741f0171b89c297b63041116d704 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:20 +0100 -Subject: [PATCH 02/11] MIPS: BCM63XX: add USB device clock enable delay to - clock code - -This patch adds the required 10 micro seconds delay to the USB device -clock enable operation. Put this where the correct clock knowledege is, -which is in the clock code, and remove this delay from the bcm63xx_udc -gadget driver where it was before. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/clk.c | 5 +++++ - drivers/usb/gadget/bcm63xx_udc.c | 1 - - 2 files changed, 5 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -199,6 +199,11 @@ static void usbd_set(struct clk *clk, in - bcm_hwclock_set(CKCTL_6362_USBD_EN, enable); - else if (BCMCPU_IS_6368()) - bcm_hwclock_set(CKCTL_6368_USBD_EN, enable); -+ else -+ return; -+ -+ if (enable) -+ udelay(10); - } - - static struct clk clk_usbd = { ---- a/drivers/usb/gadget/bcm63xx_udc.c -+++ b/drivers/usb/gadget/bcm63xx_udc.c -@@ -386,7 +386,6 @@ static inline void set_clocks(struct bcm - if (is_enabled) { - clk_enable(udc->usbh_clk); - clk_enable(udc->usbd_clk); -- udelay(10); - } else { - clk_disable(udc->usbd_clk); - clk_disable(udc->usbh_clk); diff --git a/target/linux/brcm63xx/patches-3.9/112-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch b/target/linux/brcm63xx/patches-3.9/112-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch deleted file mode 100644 index 4d00f0e763..0000000000 --- a/target/linux/brcm63xx/patches-3.9/112-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch +++ /dev/null @@ -1,151 +0,0 @@ -From ac9b0b574d54be28b300bf99ffe092a2c589484f Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:21 +0100 -Subject: [PATCH 03/11] MIPS: BCM63XX: move code touching the USB private - register - -This patch moves the code touching the USB private register in the -bcm63xx USB gadget driver to arch/mips/bcm63xx/usb-common.c in -preparation for adding support for OHCI and EHCI host controllers which -will also touch the USB private register. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/usb-common.c | 53 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 9 ++++ - drivers/usb/gadget/bcm63xx_udc.c | 27 ++-------- - 4 files changed, 67 insertions(+), 24 deletions(-) - create mode 100644 arch/mips/bcm63xx/usb-common.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,7 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ - dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \ -- dev-usb-usbd.o -+ dev-usb-usbd.o usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/usb-common.c -@@ -0,0 +1,53 @@ -+/* -+ * Broadcom BCM63xx common USB device configuration code -+ * -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2012 Kevin Cernekee -+ * Copyright (C) 2012 Broadcom Corporation -+ * -+ */ -+#include -+ -+#include -+#include -+#include -+#include -+ -+void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device) -+{ -+ u32 val; -+ -+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); -+ if (is_device) { -+ val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); -+ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -+ } else { -+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); -+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -+ } -+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); -+ -+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -+ if (is_device) -+ val |= USBH_PRIV_SWAP_USBD_MASK; -+ else -+ val &= ~USBH_PRIV_SWAP_USBD_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); -+} -+EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode); -+ -+void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on) -+{ -+ u32 val; -+ -+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); -+ if (is_on) -+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -+ else -+ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); -+} -+EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup); ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h -@@ -0,0 +1,9 @@ -+#ifndef BCM63XX_USB_PRIV_H_ -+#define BCM63XX_USB_PRIV_H_ -+ -+#include -+ -+void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device); -+void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on); -+ -+#endif /* BCM63XX_USB_PRIV_H_ */ ---- a/drivers/usb/gadget/bcm63xx_udc.c -+++ b/drivers/usb/gadget/bcm63xx_udc.c -@@ -41,6 +41,7 @@ - #include - #include - #include -+#include - - #define DRV_MODULE_NAME "bcm63xx_udc" - -@@ -863,22 +864,7 @@ static void bcm63xx_select_phy_mode(stru - bcm_gpio_writel(val, GPIO_PINMUX_OTHR_REG); - } - -- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); -- if (is_device) { -- val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); -- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -- } else { -- val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); -- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -- } -- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); -- -- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -- if (is_device) -- val |= USBH_PRIV_SWAP_USBD_MASK; -- else -- val &= ~USBH_PRIV_SWAP_USBD_MASK; -- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); -+ bcm63xx_usb_priv_select_phy_mode(portmask, is_device); - } - - /** -@@ -892,14 +878,9 @@ static void bcm63xx_select_phy_mode(stru - */ - static void bcm63xx_select_pullup(struct bcm63xx_udc *udc, bool is_on) - { -- u32 val, portmask = BIT(udc->pd->port_no); -+ u32 portmask = BIT(udc->pd->port_no); - -- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); -- if (is_on) -- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -- else -- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); -- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); -+ bcm63xx_usb_priv_select_pullup(portmask, is_on); - } - - /** diff --git a/target/linux/brcm63xx/patches-3.9/113-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch b/target/linux/brcm63xx/patches-3.9/113-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch deleted file mode 100644 index 40bbe083a7..0000000000 --- a/target/linux/brcm63xx/patches-3.9/113-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch +++ /dev/null @@ -1,169 +0,0 @@ -From 28758a9da77954ed323f86123ef448c6a563c037 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:22 +0100 -Subject: [PATCH 04/11] MIPS: BCM63XX: add OHCI/EHCI configuration bits to - common USB code - -This patch updates the common USB code touching the USB private -registers with the specific bits to properly enable OHCI and EHCI -controllers on BCM63xx SoCs. As a result we now need to protect access -to Read Modify Write sequences using a spinlock because we cannot -guarantee that any of the exposed helper will not be called -concurrently. - -Signed-off-by: Maxime Bizon -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/usb-common.c | 97 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 2 + - 2 files changed, 99 insertions(+) - ---- a/arch/mips/bcm63xx/usb-common.c -+++ b/arch/mips/bcm63xx/usb-common.c -@@ -5,10 +5,12 @@ - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * -+ * Copyright (C) 2008 Maxime Bizon - * Copyright (C) 2012 Kevin Cernekee - * Copyright (C) 2012 Broadcom Corporation - * - */ -+#include - #include - - #include -@@ -16,9 +18,14 @@ - #include - #include - -+static DEFINE_SPINLOCK(usb_priv_reg_lock); -+ - void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device) - { - u32 val; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&usb_priv_reg_lock, flags); - - val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); - if (is_device) { -@@ -36,12 +43,17 @@ void bcm63xx_usb_priv_select_phy_mode(u3 - else - val &= ~USBH_PRIV_SWAP_USBD_MASK; - bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); -+ -+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); - } - EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode); - - void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on) - { - u32 val; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&usb_priv_reg_lock, flags); - - val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); - if (is_on) -@@ -49,5 +61,90 @@ void bcm63xx_usb_priv_select_pullup(u32 - else - val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); - bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); -+ -+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); - } - EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup); -+ -+/* The following array represents the meaning of the DESC/DATA -+ * endian swapping with respect to the CPU configured endianness -+ * -+ * DATA ENDN mmio descriptor -+ * 0 0 BE invalid -+ * 0 1 BE LE -+ * 1 0 BE BE -+ * 1 1 BE invalid -+ * -+ * Since BCM63XX SoCs are configured to be in big-endian mode -+ * we want configuration at line 3. -+ */ -+void bcm63xx_usb_priv_ohci_cfg_set(void) -+{ -+ u32 reg; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&usb_priv_reg_lock, flags); -+ -+ if (BCMCPU_IS_6348()) -+ bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG); -+ else if (BCMCPU_IS_6358()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); -+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); -+ /* -+ * The magic value comes for the original vendor BSP -+ * and is needed for USB to work. Datasheet does not -+ * help, so the magic value is used as-is. -+ */ -+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, -+ USBH_PRIV_TEST_6358_REG); -+ -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); -+ -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); -+ reg |= USBH_PRIV_SETUP_IOC_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); -+ } -+ -+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); -+} -+ -+void bcm63xx_usb_priv_ehci_cfg_set(void) -+{ -+ u32 reg; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&usb_priv_reg_lock, flags); -+ -+ if (BCMCPU_IS_6358()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); -+ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); -+ -+ /* -+ * The magic value comes for the original vendor BSP -+ * and is needed for USB to work. Datasheet does not -+ * help, so the magic value is used as-is. -+ */ -+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, -+ USBH_PRIV_TEST_6358_REG); -+ -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -+ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); -+ -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); -+ reg |= USBH_PRIV_SETUP_IOC_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); -+ } -+ -+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); -+} ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h -@@ -5,5 +5,7 @@ - - void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device); - void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on); -+void bcm63xx_usb_priv_ohci_cfg_set(void); -+void bcm63xx_usb_priv_ehci_cfg_set(void); - - #endif /* BCM63XX_USB_PRIV_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/114-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch b/target/linux/brcm63xx/patches-3.9/114-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch deleted file mode 100644 index 03fa41c410..0000000000 --- a/target/linux/brcm63xx/patches-3.9/114-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch +++ /dev/null @@ -1,62 +0,0 @@ -From 94ec618bd1a6b07fafbbfc9bcc54e7f9360ff9a0 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:23 +0100 -Subject: [PATCH 05/11] MIPS: BCM63XX: introduce BCM63XX_OHCI configuration - symbol - -This configuration symbol can be used by CPUs supporting the on-chip -OHCI controller, and ensures that all relevant OHCI-related -configuration options are correctly selected. So far, OHCI support is -available for the 6328, 6348, 6358 and 6358 SoCs. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/Kconfig | 15 ++++++++++----- - 1 file changed, 10 insertions(+), 5 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -6,10 +6,17 @@ config BCM63XX_CPU_3368 - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - -+config BCM63XX_OHCI -+ bool -+ select USB_ARCH_HAS_OHCI -+ select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD -+ select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD -+ - config BCM63XX_CPU_6328 - bool "support 6328 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI -+ select BCM63XX_OHCI - - config BCM63XX_CPU_6338 - bool "support 6338 CPU" -@@ -24,21 +31,25 @@ config BCM63XX_CPU_6348 - bool "support 6348 CPU" - select SYS_HAS_CPU_BMIPS3300 - select HW_HAS_PCI -+ select BCM63XX_OHCI - - config BCM63XX_CPU_6358 - bool "support 6358 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI -+ select BCM63XX_OHCI - - config BCM63XX_CPU_6362 - bool "support 6362 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI -+ select BCM63XX_OHCI - - config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI -+ select BCM63XX_OHCI - endmenu - - source "arch/mips/bcm63xx/boards/Kconfig" diff --git a/target/linux/brcm63xx/patches-3.9/115-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch b/target/linux/brcm63xx/patches-3.9/115-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch deleted file mode 100644 index 732fe94cfd..0000000000 --- a/target/linux/brcm63xx/patches-3.9/115-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch +++ /dev/null @@ -1,138 +0,0 @@ -From 30d22baef255c99a12c4858ce4ab0d45f0d8c9ae Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:24 +0100 -Subject: [PATCH 06/11] MIPS: BCM63XX: add support for the on-chip OHCI - controller - -Broadcom BCM63XX SoCs include an on-chip OHCI controller which can be -driven by the ohci-platform generic driver by using specific power -on/off/suspend callback to manage clocks and hardware specific -configuration. - -Signed-off-by: Maxime Bizon -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/dev-usb-ohci.c | 94 ++++++++++++++++++++ - .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h | 6 ++ - 3 files changed, 101 insertions(+), 1 deletion(-) - create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,7 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ - dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \ -- dev-usb-usbd.o usb-common.o -+ dev-usb-ohci.o dev-usb-usbd.o usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-usb-ohci.c -@@ -0,0 +1,94 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon -+ * Copyright (C) 2013 Florian Fainelli -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+#include -+#include -+#include -+#include -+ -+static struct resource ohci_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static u64 ohci_dmamask = DMA_BIT_MASK(32); -+ -+static struct clk *usb_host_clock; -+ -+static int bcm63xx_ohci_power_on(struct platform_device *pdev) -+{ -+ usb_host_clock = clk_get(&pdev->dev, "usbh"); -+ if (IS_ERR_OR_NULL(usb_host_clock)) -+ return -ENODEV; -+ -+ clk_prepare_enable(usb_host_clock); -+ -+ bcm63xx_usb_priv_ohci_cfg_set(); -+ -+ return 0; -+} -+ -+static void bcm63xx_ohci_power_off(struct platform_device *pdev) -+{ -+ if (!IS_ERR_OR_NULL(usb_host_clock)) { -+ clk_disable_unprepare(usb_host_clock); -+ clk_put(usb_host_clock); -+ } -+} -+ -+static struct usb_ohci_pdata bcm63xx_ohci_pdata = { -+ .big_endian_desc = 1, -+ .big_endian_mmio = 1, -+ .no_big_frame_no = 1, -+ .num_ports = 1, -+ .power_on = bcm63xx_ohci_power_on, -+ .power_off = bcm63xx_ohci_power_off, -+ .power_suspend = bcm63xx_ohci_power_off, -+}; -+ -+static struct platform_device bcm63xx_ohci_device = { -+ .name = "ohci-platform", -+ .id = -1, -+ .num_resources = ARRAY_SIZE(ohci_resources), -+ .resource = ohci_resources, -+ .dev = { -+ .platform_data = &bcm63xx_ohci_pdata, -+ .dma_mask = &ohci_dmamask, -+ .coherent_dma_mask = DMA_BIT_MASK(32), -+ }, -+}; -+ -+int __init bcm63xx_ohci_register(void) -+{ -+ if (BCMCPU_IS_6345() || BCMCPU_IS_6338()) -+ return -ENODEV; -+ -+ ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); -+ ohci_resources[0].end = ohci_resources[0].start; -+ ohci_resources[0].end += RSET_OHCI_SIZE - 1; -+ ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0); -+ -+ return platform_device_register(&bcm63xx_ohci_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h -@@ -0,0 +1,6 @@ -+#ifndef BCM63XX_DEV_USB_OHCI_H_ -+#define BCM63XX_DEV_USB_OHCI_H_ -+ -+int bcm63xx_ohci_register(void); -+ -+#endif /* BCM63XX_DEV_USB_OHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/116-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch b/target/linux/brcm63xx/patches-3.9/116-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch deleted file mode 100644 index 621e1f909d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/116-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 33ef960aed15f9a98a2c51d8d794cd72418e0be4 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:25 +0100 -Subject: [PATCH 07/11] MIPS: BCM63XX: register OHCI controller if board - enables it - -BCM63XX-based boards can control the registration of the OHCI controller -by setting their has_ohci0 flag to 1. Handle this in the generic -code dealing with board registration and call the actual helper to -register the OHCI controller. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -25,6 +25,7 @@ - #include - #include - #include -+#include - #include - #include - -@@ -897,6 +898,9 @@ int __init board_register_devices(void) - if (board.has_usbd) - bcm63xx_usbd_register(&board.usbd); - -+ if (board.has_ohci0) -+ bcm63xx_ohci_register(); -+ - if (board.has_dsp) - bcm63xx_dsp_register(&board.dsp); - diff --git a/target/linux/brcm63xx/patches-3.9/117-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch b/target/linux/brcm63xx/patches-3.9/117-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch deleted file mode 100644 index 97b8d6518a..0000000000 --- a/target/linux/brcm63xx/patches-3.9/117-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 00da1683364e58c6430a4577123d01037f8faddc Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:26 +0100 -Subject: [PATCH 08/11] MIPS: BCM63XX: introduce BCM63XX_EHCI configuration - symbol - -This configuration symbol can be used by CPUs supporting the on-chip -EHCI controller, and ensures that all relevant EHCI-related -configuration options are selected. So far BCM6328, BCM6358 and BCM6368 -have an EHCI controller and do select this symbol. Update -drivers/usb/host/Kconfig with BCM63XX to update direct unmet -dependencies. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/Kconfig | 9 +++++++++ - drivers/usb/host/Kconfig | 5 +++-- - 2 files changed, 12 insertions(+), 2 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -12,11 +12,18 @@ config BCM63XX_OHCI - select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD - select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD - -+config BCM63XX_EHCI -+ bool -+ select USB_ARCH_HAS_EHCI -+ select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD -+ select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD -+ - config BCM63XX_CPU_6328 - bool "support 6328 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - select BCM63XX_OHCI -+ select BCM63XX_EHCI - - config BCM63XX_CPU_6338 - bool "support 6338 CPU" -@@ -38,18 +45,21 @@ config BCM63XX_CPU_6358 - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - select BCM63XX_OHCI -+ select BCM63XX_EHCI - - config BCM63XX_CPU_6362 - bool "support 6362 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - select BCM63XX_OHCI -+ select BCM63XX_EHCI - - config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select SYS_HAS_CPU_BMIPS4350 - select HW_HAS_PCI - select BCM63XX_OHCI -+ select BCM63XX_EHCI - endmenu - - source "arch/mips/bcm63xx/boards/Kconfig" ---- a/drivers/usb/host/Kconfig -+++ b/drivers/usb/host/Kconfig -@@ -115,14 +115,15 @@ config USB_EHCI_BIG_ENDIAN_MMIO - depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \ - ARCH_IXP4XX || XPS_USB_HCD_XILINX || \ - PPC_MPC512x || CPU_CAVIUM_OCTEON || \ -- PMC_MSP || SPARC_LEON || MIPS_SEAD3) -+ PMC_MSP || SPARC_LEON || MIPS_SEAD3 || \ -+ BCM63XX) - default y - - config USB_EHCI_BIG_ENDIAN_DESC - bool - depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX || XPS_USB_HCD_XILINX || \ - PPC_MPC512x || PMC_MSP || SPARC_LEON || \ -- MIPS_SEAD3) -+ MIPS_SEAD3 || BCM63XX) - default y - - config XPS_USB_HCD_XILINX diff --git a/target/linux/brcm63xx/patches-3.9/118-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch b/target/linux/brcm63xx/patches-3.9/118-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch deleted file mode 100644 index ef4ba17a4d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/118-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch +++ /dev/null @@ -1,136 +0,0 @@ -From e38f13bd6408769c0b565bb1079024f496eee121 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:27 +0100 -Subject: [PATCH 09/11] MIPS: BCM63XX: add support for the on-chip EHCI - controller - -Broadcom BCM63XX SoCs include an on-chip EHCI controller which can be -driven by the generic ehci-platform driver by using specific power -on/off/suspend callbacks to manage clocks and hardware specific -configuration. - -Signed-off-by: Maxime Bizon -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/dev-usb-ehci.c | 92 ++++++++++++++++++++ - .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h | 6 ++ - 3 files changed, 99 insertions(+), 1 deletion(-) - create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,7 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ - dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \ -- dev-usb-ohci.o dev-usb-usbd.o usb-common.o -+ dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-usb-ehci.c -@@ -0,0 +1,92 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon -+ * Copyright (C) 2013 Florian Fainelli -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+#include -+#include -+#include -+#include -+ -+static struct resource ehci_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static u64 ehci_dmamask = DMA_BIT_MASK(32); -+ -+static struct clk *usb_host_clock; -+ -+static int bcm63xx_ehci_power_on(struct platform_device *pdev) -+{ -+ usb_host_clock = clk_get(&pdev->dev, "usbh"); -+ if (IS_ERR_OR_NULL(usb_host_clock)) -+ return -ENODEV; -+ -+ clk_prepare_enable(usb_host_clock); -+ -+ bcm63xx_usb_priv_ehci_cfg_set(); -+ -+ return 0; -+} -+ -+static void bcm63xx_ehci_power_off(struct platform_device *pdev) -+{ -+ if (!IS_ERR_OR_NULL(usb_host_clock)) { -+ clk_disable_unprepare(usb_host_clock); -+ clk_put(usb_host_clock); -+ } -+} -+ -+static struct usb_ehci_pdata bcm63xx_ehci_pdata = { -+ .big_endian_desc = 1, -+ .big_endian_mmio = 1, -+ .power_on = bcm63xx_ehci_power_on, -+ .power_off = bcm63xx_ehci_power_off, -+ .power_suspend = bcm63xx_ehci_power_off, -+}; -+ -+static struct platform_device bcm63xx_ehci_device = { -+ .name = "ehci-platform", -+ .id = -1, -+ .num_resources = ARRAY_SIZE(ehci_resources), -+ .resource = ehci_resources, -+ .dev = { -+ .platform_data = &bcm63xx_ehci_pdata, -+ .dma_mask = &ehci_dmamask, -+ .coherent_dma_mask = DMA_BIT_MASK(32), -+ }, -+}; -+ -+int __init bcm63xx_ehci_register(void) -+{ -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) -+ return 0; -+ -+ ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); -+ ehci_resources[0].end = ehci_resources[0].start; -+ ehci_resources[0].end += RSET_EHCI_SIZE - 1; -+ ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0); -+ -+ return platform_device_register(&bcm63xx_ehci_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h -@@ -0,0 +1,6 @@ -+#ifndef BCM63XX_DEV_USB_EHCI_H_ -+#define BCM63XX_DEV_USB_EHCI_H_ -+ -+int bcm63xx_ehci_register(void); -+ -+#endif /* BCM63XX_DEV_USB_EHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/119-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch b/target/linux/brcm63xx/patches-3.9/119-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch deleted file mode 100644 index 3d1e7f58cc..0000000000 --- a/target/linux/brcm63xx/patches-3.9/119-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 709ef2034f5ba06da35f89856ad7baf2b7a41287 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:28 +0100 -Subject: [PATCH 10/11] MIPS: BCM63XX: register EHCI controller if board - enables it - -BCM63XX-based board can control the registration of the EHCI controller -by setting their has_ehci0 flag to 1. Handle this in the generic -code dealing with board registration and call the actual helper to register -the EHCI controller. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -25,6 +25,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -898,6 +899,9 @@ int __init board_register_devices(void) - if (board.has_usbd) - bcm63xx_usbd_register(&board.usbd); - -+ if (board.has_ehci0) -+ bcm63xx_ehci_register(); -+ - if (board.has_ohci0) - bcm63xx_ohci_register(); - diff --git a/target/linux/brcm63xx/patches-3.9/120-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch b/target/linux/brcm63xx/patches-3.9/120-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch deleted file mode 100644 index 6d91129932..0000000000 --- a/target/linux/brcm63xx/patches-3.9/120-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch +++ /dev/null @@ -1,24 +0,0 @@ -From 111bbd770441ab34f9da5bb1d85767a9b75227b4 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 28 Jan 2013 20:06:30 +0100 -Subject: [PATCH 12/12] MIPS: BCM63XX: EHCI controller does not support - overcurrent - -This patch sets the ignore_oc flag for the BCM63XX EHCI controller as it -does not support proper overcurrent reporting. - -Signed-off-by: Florian Fainelli ---- - arch/mips/bcm63xx/dev-usb-ehci.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/mips/bcm63xx/dev-usb-ehci.c -+++ b/arch/mips/bcm63xx/dev-usb-ehci.c -@@ -61,6 +61,7 @@ static void bcm63xx_ehci_power_off(struc - static struct usb_ehci_pdata bcm63xx_ehci_pdata = { - .big_endian_desc = 1, - .big_endian_mmio = 1, -+ .ignore_oc = 1, - .power_on = bcm63xx_ehci_power_on, - .power_off = bcm63xx_ehci_power_off, - .power_suspend = bcm63xx_ehci_power_off, diff --git a/target/linux/brcm63xx/patches-3.9/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch b/target/linux/brcm63xx/patches-3.9/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch deleted file mode 100644 index 00dc9c90ee..0000000000 --- a/target/linux/brcm63xx/patches-3.9/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 3f650fc30aa0badf9d02842ce396cea3eef2eeaa Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 1 Jul 2011 23:16:47 +0200 -Subject: [PATCH 49/79] SPI: Allow specifying the parsers for SPI flash - -Signed-off-by: Jonas Gorski ---- - include/linux/spi/flash.h | 5 ++++- - 1 file changed, 4 insertions(+), 1 deletion(-) - ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -2,7 +2,7 @@ - #define LINUX_SPI_FLASH_H - - struct mtd_partition; -- -+struct mtd_part_parser_data; - /** - * struct flash_platform_data: board-specific flash data - * @name: optional flash device name (eg, as used with mtdparts=) -@@ -10,6 +10,8 @@ struct mtd_partition; - * @nr_parts: number of mtd_partitions for static partitoning - * @type: optional flash device type (e.g. m25p80 vs m25p64), for use - * with chips that can't be queried for JEDEC or other IDs -+ * @part_probe_types: optional list of MTD parser names to use for -+ * partitioning - * - * Board init code (in arch/.../mach-xxx/board-yyy.c files) can - * provide information about SPI flash parts (such as DataFlash) to -@@ -25,6 +27,7 @@ struct flash_platform_data { - - char *type; - -+ const char **part_probe_types; - /* we'll likely add more ... use JEDEC IDs, etc */ - }; - diff --git a/target/linux/brcm63xx/patches-3.9/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch b/target/linux/brcm63xx/patches-3.9/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch deleted file mode 100644 index b5df076dbc..0000000000 --- a/target/linux/brcm63xx/patches-3.9/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch +++ /dev/null @@ -1,23 +0,0 @@ -From c7c3c338cb25d7f55ddb3f6bfbf3572758ca3896 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 10 Nov 2011 16:53:08 +0100 -Subject: [PATCH 50/79] MTD: DEVICES: m25p80: use parsers if provided in flash - platform data - -Signed-off-by: Jonas Gorski ---- - drivers/mtd/devices/m25p80.c | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -1088,7 +1088,8 @@ static int m25p_probe(struct spi_device - /* partitions should match sector boundaries; and it may be good to - * use readonly partitions for writeprotected sectors (BP2..BP0). - */ -- return mtd_device_parse_register(&flash->mtd, NULL, &ppdata, -+ return mtd_device_parse_register(&flash->mtd, -+ data ? data->part_probe_types : NULL, &ppdata, - data ? data->parts : NULL, - data ? data->nr_parts : 0); - } diff --git a/target/linux/brcm63xx/patches-3.9/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch b/target/linux/brcm63xx/patches-3.9/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch deleted file mode 100644 index 7ac1b2fb10..0000000000 --- a/target/linux/brcm63xx/patches-3.9/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch +++ /dev/null @@ -1,92 +0,0 @@ -From 5fb4e8d7287ac8fcb33aae8b1e9e22c5a3c392bd Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 10 Nov 2011 17:33:40 +0100 -Subject: [PATCH 51/79] MTD: DEVICES: m25p80: add support for limiting reads - -Signed-off-by: Jonas Gorski ---- - drivers/mtd/devices/m25p80.c | 29 +++++++++++++++++++++++++++-- - include/linux/spi/flash.h | 4 ++++ - 2 files changed, 31 insertions(+), 2 deletions(-) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -93,6 +93,7 @@ struct m25p { - u8 erase_opcode; - u8 *command; - bool fast_read; -+ int max_transfer_len; - }; - - static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd) -@@ -337,10 +338,9 @@ static int m25p80_erase(struct mtd_info - * Read an address range from the flash chip. The address range - * may be any size provided it is within the physical boundaries. - */ --static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, -+static int __m25p80_read(struct m25p *flash, loff_t from, size_t len, - size_t *retlen, u_char *buf) - { -- struct m25p *flash = mtd_to_m25p(mtd); - struct spi_transfer t[2]; - struct spi_message m; - uint8_t opcode; -@@ -392,6 +392,28 @@ static int m25p80_read(struct mtd_info * - return 0; - } - -+static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, -+ size_t *retlen, u_char *buf) -+{ -+ struct m25p *flash = mtd_to_m25p(mtd); -+ size_t off; -+ size_t read_len = flash->max_transfer_len; -+ size_t part_len; -+ int ret = 0; -+ -+ if (!read_len) -+ return __m25p80_read(flash, from, len, retlen, buf); -+ -+ *retlen = 0; -+ -+ for (off = 0; off < len && !ret; off += read_len) { -+ ret = __m25p80_read(flash, from + off, min(len - off, read_len), -+ &part_len, buf + off); -+ *retlen += part_len; -+ } -+ -+ return ret; -+} - /* - * Write an address range to the flash chip. Data must be written in - * FLASH_PAGESIZE chunks. The address range may be any size provided -@@ -983,6 +1005,9 @@ static int m25p_probe(struct spi_device - return -ENOMEM; - } - -+ if (data) -+ flash->max_transfer_len = data->max_transfer_len; -+ - flash->spi = spi; - mutex_init(&flash->lock); - dev_set_drvdata(&spi->dev, flash); ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -13,6 +13,8 @@ struct mtd_part_parser_data; - * @part_probe_types: optional list of MTD parser names to use for - * partitioning - * -+ * @max_transfer_len: option maximum read/write length limitation for -+ * SPI controllers not able to transfer any length commands. - * Board init code (in arch/.../mach-xxx/board-yyy.c files) can - * provide information about SPI flash parts (such as DataFlash) to - * help set up the device and its appropriate default partitioning. -@@ -28,6 +30,8 @@ struct flash_platform_data { - char *type; - - const char **part_probe_types; -+ -+ unsigned int max_transfer_len; - /* we'll likely add more ... use JEDEC IDs, etc */ - }; - diff --git a/target/linux/brcm63xx/patches-3.9/300-reset_buttons.patch b/target/linux/brcm63xx/patches-3.9/300-reset_buttons.patch deleted file mode 100644 index fcd3c52ecd..0000000000 --- a/target/linux/brcm63xx/patches-3.9/300-reset_buttons.patch +++ /dev/null @@ -1,116 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -12,6 +12,8 @@ - #include - #include - #include -+#include -+#include - #include - #include - #include -@@ -36,6 +38,9 @@ - - #define HCS_OFFSET_128K 0x20000 - -+#define BCM963XX_KEYS_POLL_INTERVAL 20 -+#define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) -+ - static struct board_info board; - - /* -@@ -379,6 +384,16 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_96348gw = { -@@ -437,6 +452,16 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_FAST2404 = { -@@ -870,11 +895,23 @@ static struct platform_device bcm63xx_gp - .dev.platform_data = &bcm63xx_led_data, - }; - -+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = { -+ .poll_interval = BCM963XX_KEYS_POLL_INTERVAL, -+}; -+ -+static struct platform_device bcm63xx_gpio_keys_device = { -+ .name = "gpio-keys-polled", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_gpio_keys_data, -+}; -+ - /* - * third stage init callback, register all board devices. - */ - int __init board_register_devices(void) - { -+ int button_count = 0; -+ - if (board.has_uart0) - bcm63xx_uart_register(0); - -@@ -934,5 +971,16 @@ int __init board_register_devices(void) - gpio_request_one(board.ephy_reset_gpio, - board.ephy_reset_gpio_flags, "ephy-reset"); - -+ /* count number of BUTTONs defined by this device */ -+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) -+ button_count++; -+ -+ if (button_count) { -+ bcm63xx_gpio_keys_data.nbuttons = button_count; -+ bcm63xx_gpio_keys_data.buttons = board.buttons; -+ -+ platform_device_register(&bcm63xx_gpio_keys_device); -+ } -+ - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -3,6 +3,7 @@ - - #include - #include -+#include - #include - #include - #include -@@ -48,6 +49,9 @@ struct board_info { - /* GPIO LEDs */ - struct gpio_led leds[5]; - -+ /* Buttons */ -+ struct gpio_keys_button buttons[4]; -+ - /* External PHY reset GPIO */ - unsigned int ephy_reset_gpio; - diff --git a/target/linux/brcm63xx/patches-3.9/301-led_count.patch b/target/linux/brcm63xx/patches-3.9/301-led_count.patch deleted file mode 100644 index e8234b0285..0000000000 --- a/target/linux/brcm63xx/patches-3.9/301-led_count.patch +++ /dev/null @@ -1,41 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -911,6 +911,7 @@ static struct platform_device bcm63xx_gp - int __init board_register_devices(void) - { - int button_count = 0; -+ int led_count = 0; - - if (board.has_uart0) - bcm63xx_uart_register(0); -@@ -962,10 +963,16 @@ int __init board_register_devices(void) - - bcm63xx_flash_register(); - -- bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds); -- bcm63xx_led_data.leds = board.leds; -+ /* count number of LEDs defined by this device */ -+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) -+ led_count++; -+ -+ if (led_count) { -+ bcm63xx_led_data.num_leds = led_count; -+ bcm63xx_led_data.leds = board.leds; - -- platform_device_register(&bcm63xx_gpio_leds); -+ platform_device_register(&bcm63xx_gpio_leds); -+ } - - if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags) - gpio_request_one(board.ephy_reset_gpio, ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -47,7 +47,7 @@ struct board_info { - struct bcm63xx_dsp_platform_data dsp; - - /* GPIO LEDs */ -- struct gpio_led leds[5]; -+ struct gpio_led leds[14]; - - /* Buttons */ - struct gpio_keys_button buttons[4]; diff --git a/target/linux/brcm63xx/patches-3.9/302-extended-platform-devices.patch b/target/linux/brcm63xx/patches-3.9/302-extended-platform-devices.patch deleted file mode 100644 index c657b19688..0000000000 --- a/target/linux/brcm63xx/patches-3.9/302-extended-platform-devices.patch +++ /dev/null @@ -1,25 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -961,6 +961,9 @@ int __init board_register_devices(void) - - bcm63xx_spi_register(); - -+ if (board.num_devs) -+ platform_add_devices(board.devs, board.num_devs); -+ - bcm63xx_flash_register(); - - /* count number of LEDs defined by this device */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -57,6 +57,10 @@ struct board_info { - - /* External PHY reset GPIO flags from gpio.h */ - unsigned long ephy_reset_gpio_flags; -+ -+ /* Additional platform devices */ -+ struct platform_device **devs; -+ unsigned int num_devs; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/303-spi-board-info.patch b/target/linux/brcm63xx/patches-3.9/303-spi-board-info.patch deleted file mode 100644 index ce3da3f158..0000000000 --- a/target/linux/brcm63xx/patches-3.9/303-spi-board-info.patch +++ /dev/null @@ -1,33 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -14,6 +14,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -964,6 +965,9 @@ int __init board_register_devices(void) - if (board.num_devs) - platform_add_devices(board.devs, board.num_devs); - -+ if (board.num_spis) -+ spi_register_board_info(board.spis, board.num_spis); -+ - bcm63xx_flash_register(); - - /* count number of LEDs defined by this device */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -61,6 +61,10 @@ struct board_info { - /* Additional platform devices */ - struct platform_device **devs; - unsigned int num_devs; -+ -+ /* Additional platform devices */ -+ struct spi_board_info *spis; -+ unsigned int num_spis; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/304-boardid_fixup.patch b/target/linux/brcm63xx/patches-3.9/304-boardid_fixup.patch deleted file mode 100644 index 6dfb540b7c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/304-boardid_fixup.patch +++ /dev/null @@ -1,62 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -34,6 +34,7 @@ - #include - - #include -+#include - - #define PFX "board_bcm963xx: " - -@@ -42,6 +43,9 @@ - #define BCM963XX_KEYS_POLL_INTERVAL 20 - #define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) - -+#define CFE_OFFSET_64K 0x10000 -+#define CFE_OFFSET_128K 0x20000 -+ - static struct board_info board; - - /* -@@ -781,6 +785,30 @@ const char *board_get_name(void) - return board.name; - } - -+static void __init boardid_fixup(u8 *boot_addr) -+{ -+ struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); -+ char *board_name = (char *)bcm63xx_nvram_get_name(); -+ -+ /* check if bcm_tag is at 64k offset */ -+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { -+ /* else try 128k */ -+ tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K); -+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { -+ /* No tag found */ -+ printk(KERN_DEBUG "No bcm_tag found!\n"); -+ return; -+ } -+ } -+ /* check if we should override the boardid */ -+ if (tag->information1[0] != '+') -+ return; -+ -+ strncpy(board_name, &tag->information1[1], BOARDID_LEN); -+ -+ printk(KERN_INFO "Overriding boardid with '%s'\n", board_name); -+} -+ - /* - * early init callback, read nvram data from flash and checksum it - */ -@@ -819,6 +847,10 @@ void __init board_prom_init(void) - hcs = (struct bcm_hcs *)boot_addr; - board_name = hcs->filename; - } else { -+ if (strcmp(cfe_version, "unknown") != 0) { -+ /* cfe present */ -+ boardid_fixup(boot_addr); -+ } - board_name = bcm63xx_nvram_get_name(); - } - /* find board by name */ diff --git a/target/linux/brcm63xx/patches-3.9/306-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch b/target/linux/brcm63xx/patches-3.9/306-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch deleted file mode 100644 index 6b3b980356..0000000000 --- a/target/linux/brcm63xx/patches-3.9/306-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 5aeb6273a610f8aab090b3499827177eb41311ba Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 12 Nov 2011 12:19:09 +0100 -Subject: [PATCH 53/79] MIPS: BCM63XX: expose the HS SPI clock - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/clk.c | 22 ++++++++++++++++++++++ - 1 file changed, 22 insertions(+) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -236,6 +236,26 @@ static struct clk clk_spi = { - }; - - /* -+ * SPI clock -+ */ -+static void hsspi_set(struct clk *clk, int enable) -+{ -+ u32 mask; -+ -+ if (BCMCPU_IS_6328()) -+ mask = CKCTL_6328_HSSPI_EN; -+ else -+ return; -+ -+ bcm_hwclock_set(mask, enable); -+} -+ -+static struct clk clk_hsspi = { -+ .set = hsspi_set, -+}; -+ -+ -+/* - * XTM clock - */ - static void xtm_set(struct clk *clk, int enable) -@@ -344,6 +364,8 @@ struct clk *clk_get(struct device *dev, - return &clk_usbd; - if (!strcmp(id, "spi")) - return &clk_spi; -+ if (!strcmp(id, "hsspi")) -+ return &clk_hsspi; - if (!strcmp(id, "xtm")) - return &clk_xtm; - if (!strcmp(id, "periph")) diff --git a/target/linux/brcm63xx/patches-3.9/307-MIPS-BCM63XX-add-HSSPI-register-definitions.patch b/target/linux/brcm63xx/patches-3.9/307-MIPS-BCM63XX-add-HSSPI-register-definitions.patch deleted file mode 100644 index 28334b160f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/307-MIPS-BCM63XX-add-HSSPI-register-definitions.patch +++ /dev/null @@ -1,211 +0,0 @@ -From 70f970222bc1096689ae1bffeb9ed09a7c4bed07 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 12 Nov 2011 12:19:55 +0100 -Subject: [PATCH 28/60] MIPS: BCM63XX: add HSSPI register definitions - -Signed-off-by: Jonas Gorski ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 18 ++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 47 +++++++++++++++++++++ - 2 files changed, 65 insertions(+), 0 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -145,6 +145,7 @@ enum bcm63xx_regs_set { - RSET_UART1, - RSET_GPIO, - RSET_SPI, -+ RSET_HSSPI, - RSET_UDC0, - RSET_OHCI0, - RSET_OHCI_PRIV, -@@ -193,6 +194,7 @@ enum bcm63xx_regs_set { - #define RSET_ENETDMAS_SIZE(chans) (16 * (chans)) - #define RSET_ENETSW_SIZE 65536 - #define RSET_UART_SIZE 24 -+#define RSET_HSSPI_SIZE 1536 - #define RSET_UDC_SIZE 256 - #define RSET_OHCI_SIZE 256 - #define RSET_EHCI_SIZE 256 -@@ -265,6 +267,7 @@ enum bcm63xx_regs_set { - #define BCM_6328_UART1_BASE (0xb0000120) - #define BCM_6328_GPIO_BASE (0xb0000080) - #define BCM_6328_SPI_BASE (0xdeadbeef) -+#define BCM_6328_HSSPI_BASE (0xb0001000) - #define BCM_6328_UDC0_BASE (0xdeadbeef) - #define BCM_6328_USBDMA_BASE (0xb000c000) - #define BCM_6328_OHCI0_BASE (0xb0002600) -@@ -313,6 +316,7 @@ enum bcm63xx_regs_set { - #define BCM_6338_UART1_BASE (0xdeadbeef) - #define BCM_6338_GPIO_BASE (0xfffe0400) - #define BCM_6338_SPI_BASE (0xfffe0c00) -+#define BCM_6338_HSSPI_BASE (0xdeadbeef) - #define BCM_6338_UDC0_BASE (0xdeadbeef) - #define BCM_6338_USBDMA_BASE (0xfffe2400) - #define BCM_6338_OHCI0_BASE (0xdeadbeef) -@@ -360,6 +364,7 @@ enum bcm63xx_regs_set { - #define BCM_6345_UART1_BASE (0xdeadbeef) - #define BCM_6345_GPIO_BASE (0xfffe0400) - #define BCM_6345_SPI_BASE (0xdeadbeef) -+#define BCM_6345_HSSPI_BASE (0xdeadbeef) - #define BCM_6345_UDC0_BASE (0xdeadbeef) - #define BCM_6345_USBDMA_BASE (0xfffe2800) - #define BCM_6345_ENET0_BASE (0xfffe1800) -@@ -406,6 +411,7 @@ enum bcm63xx_regs_set { - #define BCM_6348_UART1_BASE (0xdeadbeef) - #define BCM_6348_GPIO_BASE (0xfffe0400) - #define BCM_6348_SPI_BASE (0xfffe0c00) -+#define BCM_6348_HSSPI_BASE (0xdeadbeef) - #define BCM_6348_UDC0_BASE (0xfffe1000) - #define BCM_6348_USBDMA_BASE (0xdeadbeef) - #define BCM_6348_OHCI0_BASE (0xfffe1b00) -@@ -451,6 +457,7 @@ enum bcm63xx_regs_set { - #define BCM_6358_UART1_BASE (0xfffe0120) - #define BCM_6358_GPIO_BASE (0xfffe0080) - #define BCM_6358_SPI_BASE (0xfffe0800) -+#define BCM_6358_HSSPI_BASE (0xdeadbeef) - #define BCM_6358_UDC0_BASE (0xfffe0800) - #define BCM_6358_USBDMA_BASE (0xdeadbeef) - #define BCM_6358_OHCI0_BASE (0xfffe1400) -@@ -553,6 +560,7 @@ enum bcm63xx_regs_set { - #define BCM_6368_UART1_BASE (0xb0000120) - #define BCM_6368_GPIO_BASE (0xb0000080) - #define BCM_6368_SPI_BASE (0xb0000800) -+#define BCM_6368_HSSPI_BASE (0xdeadbeef) - #define BCM_6368_UDC0_BASE (0xdeadbeef) - #define BCM_6368_USBDMA_BASE (0xb0004800) - #define BCM_6368_OHCI0_BASE (0xb0001600) -@@ -604,6 +612,7 @@ extern const unsigned long *bcm63xx_regs - __GEN_RSET_BASE(__cpu, UART1) \ - __GEN_RSET_BASE(__cpu, GPIO) \ - __GEN_RSET_BASE(__cpu, SPI) \ -+ __GEN_RSET_BASE(__cpu, HSSPI) \ - __GEN_RSET_BASE(__cpu, UDC0) \ - __GEN_RSET_BASE(__cpu, OHCI0) \ - __GEN_RSET_BASE(__cpu, OHCI_PRIV) \ -@@ -647,6 +656,7 @@ extern const unsigned long *bcm63xx_regs - [RSET_UART1] = BCM_## __cpu ##_UART1_BASE, \ - [RSET_GPIO] = BCM_## __cpu ##_GPIO_BASE, \ - [RSET_SPI] = BCM_## __cpu ##_SPI_BASE, \ -+ [RSET_HSSPI] = BCM_## __cpu ##_HSSPI_BASE, \ - [RSET_UDC0] = BCM_## __cpu ##_UDC0_BASE, \ - [RSET_OHCI0] = BCM_## __cpu ##_OHCI0_BASE, \ - [RSET_OHCI_PRIV] = BCM_## __cpu ##_OHCI_PRIV_BASE, \ -@@ -727,6 +737,7 @@ enum bcm63xx_irq { - IRQ_ENET0, - IRQ_ENET1, - IRQ_ENET_PHY, -+ IRQ_HSSPI, - IRQ_OHCI0, - IRQ_EHCI0, - IRQ_USBD, -@@ -815,6 +826,7 @@ enum bcm63xx_irq { - #define BCM_6328_ENET0_IRQ 0 - #define BCM_6328_ENET1_IRQ 0 - #define BCM_6328_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6328_HSSPI_IRQ (IRQ_INTERNAL_BASE + 29) - #define BCM_6328_OHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 9) - #define BCM_6328_EHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 10) - #define BCM_6328_USBD_IRQ (IRQ_INTERNAL_BASE + 4) -@@ -860,6 +872,7 @@ enum bcm63xx_irq { - #define BCM_6338_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6338_ENET1_IRQ 0 - #define BCM_6338_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6338_HSSPI_IRQ 0 - #define BCM_6338_OHCI0_IRQ 0 - #define BCM_6338_EHCI0_IRQ 0 - #define BCM_6338_USBD_IRQ 0 -@@ -898,6 +911,7 @@ enum bcm63xx_irq { - #define BCM_6345_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6345_ENET1_IRQ 0 - #define BCM_6345_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6345_HSSPI_IRQ 0 - #define BCM_6345_OHCI0_IRQ 0 - #define BCM_6345_EHCI0_IRQ 0 - #define BCM_6345_USBD_IRQ 0 -@@ -936,6 +950,7 @@ enum bcm63xx_irq { - #define BCM_6348_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6348_ENET1_IRQ (IRQ_INTERNAL_BASE + 7) - #define BCM_6348_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6348_HSSPI_IRQ 0 - #define BCM_6348_OHCI0_IRQ (IRQ_INTERNAL_BASE + 12) - #define BCM_6348_EHCI0_IRQ 0 - #define BCM_6348_USBD_IRQ 0 -@@ -974,6 +989,7 @@ enum bcm63xx_irq { - #define BCM_6358_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6358_ENET1_IRQ (IRQ_INTERNAL_BASE + 6) - #define BCM_6358_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6358_HSSPI_IRQ 0 - #define BCM_6358_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5) - #define BCM_6358_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) - #define BCM_6358_USBD_IRQ 0 -@@ -1086,6 +1102,7 @@ enum bcm63xx_irq { - #define BCM_6368_ENET0_IRQ 0 - #define BCM_6368_ENET1_IRQ 0 - #define BCM_6368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 15) -+#define BCM_6368_HSSPI_IRQ 0 - #define BCM_6368_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5) - #define BCM_6368_EHCI0_IRQ (IRQ_INTERNAL_BASE + 7) - #define BCM_6368_USBD_IRQ (IRQ_INTERNAL_BASE + 8) -@@ -1133,6 +1150,7 @@ extern const int *bcm63xx_irqs; - [IRQ_ENET0] = BCM_## __cpu ##_ENET0_IRQ, \ - [IRQ_ENET1] = BCM_## __cpu ##_ENET1_IRQ, \ - [IRQ_ENET_PHY] = BCM_## __cpu ##_ENET_PHY_IRQ, \ -+ [IRQ_HSSPI] = BCM_## __cpu ##_HSSPI_IRQ, \ - [IRQ_OHCI0] = BCM_## __cpu ##_OHCI0_IRQ, \ - [IRQ_EHCI0] = BCM_## __cpu ##_EHCI0_IRQ, \ - [IRQ_USBD] = BCM_## __cpu ##_USBD_IRQ, \ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1561,4 +1561,51 @@ - #define OTP_USER_BITS_6328_REG(i) (0x20 + (i) * 4) - #define OTP_6328_REG3_TP1_DISABLED BIT(9) - -+/************************************************************************* -+ * _REG relative to RSET_HSSPI -+ *************************************************************************/ -+ -+#define HSSPI_GLOBAL_CTRL_REG 0x0 -+#define GLOBAL_CTRL_CLK_POLARITY (1 << 17) -+#define GLOBAL_CTRL_CLK_GATE_SSOFF (1 << 16) -+ -+#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4 -+ -+#define HSSPI_INT_STATUS_REG 0x8 -+#define HSSPI_INT_STATUS_MASKED_REG 0xc -+#define HSSPI_INT_MASK_REG 0x10 -+ -+#define HSSPI_PING0_CMD_DONE (1 << 0) -+ -+#define HSSPI_INT_CLEAR_ALL 0xff001f1f -+ -+#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40) -+#define PINGPONG_CMD_COMMAND_MASK 0xf -+#define PINGPONG_COMMAND_NOOP 0 -+#define PINGPONG_COMMAND_START_NOW 1 -+#define PINGPONG_COMMAND_START_TRIGGER 2 -+#define PINGPONG_COMMAND_HALT 3 -+#define PINGPONG_COMMAND_FLUSH 4 -+#define PINGPONG_CMD_PROFILE_SHIFT 8 -+#define PINGPONG_CMD_SS_SHIFT 12 -+ -+#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40) -+ -+#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20) -+#define CLK_CTRL_ACCUM_RST_ON_LOOP (1 << 15) -+ -+#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20) -+#define SIGNAL_CTRL_LATCH_RISING (1 << 12) -+#define SIGNAL_CTRL_LAUNCH_RISING (1 << 13) -+#define SIGNAL_CTRL_ASYNC_INPUT_PATH (1 << 16) -+ -+#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20) -+#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8 -+#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12 -+#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16 -+#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18 -+#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24 -+ -+#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200) -+ - #endif /* BCM63XX_REGS_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/308-board_leds_naming.patch b/target/linux/brcm63xx/patches-3.9/308-board_leds_naming.patch deleted file mode 100644 index 0a4ea30e7e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/308-board_leds_naming.patch +++ /dev/null @@ -1,267 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -147,28 +147,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96338GW:green:adsl", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ses", -+ .name = "96338GW:green:ses", - .gpio = 5, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96338GW:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96338GW:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96338GW:green:stop", - .gpio = 1, - .active_low = 1, - } -@@ -188,28 +188,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96338W:green:adsl", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ses", -+ .name = "96338W:green:ses", - .gpio = 5, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96338W:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96338W:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96338W:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -248,29 +248,29 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348R:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348R:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348R:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348R:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - - }, - { -- .name = "stop", -+ .name = "96348R:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -309,28 +309,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW-10:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW-10:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW-10:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW-10:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW-10:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -363,28 +363,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW-11:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW-11:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW-11:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW-11:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW-11:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -431,28 +431,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -584,27 +584,27 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96358VW:green:adsl-fail", - .gpio = 15, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96358VW:green:ppp", - .gpio = 22, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96358VW:green:ppp-fail", - .gpio = 23, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96358VW:green:power", - .gpio = 4, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96358VW:green:stop", - .gpio = 5, - }, - }, -@@ -636,22 +636,22 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96358VW2:green:adsl", - .gpio = 22, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96358VW2:green:ppp-fail", - .gpio = 23, - }, - { -- .name = "power", -+ .name = "96358VW2:green:power", - .gpio = 5, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96358VW2:green:stop", - .gpio = 4, - .active_low = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.9/309-cfe_version_mod.patch b/target/linux/brcm63xx/patches-3.9/309-cfe_version_mod.patch deleted file mode 100644 index 50cb14bca8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/309-cfe_version_mod.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -834,10 +834,20 @@ void __init board_prom_init(void) - - /* dump cfe version */ - cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; -- if (!memcmp(cfe, "cfe-v", 5)) -- snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u", -- cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]); -- else -+ if (strstarts(cfe, "cfe-")) { -+ if(cfe[4] == 'v') { -+ if(cfe[5] == 'd') -+ snprintf(cfe_version, 11, "%s", (char *) &cfe[5]); -+ else if (cfe[10] > 0) -+ snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u-%u", -+ cfe[5], cfe[6], cfe[7], cfe[8], cfe[9], cfe[10]); -+ else -+ snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u", -+ cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]); -+ } else { -+ snprintf(cfe_version, 12, "%s", (char *) &cfe[4]); -+ } -+ } else - strcpy(cfe_version, "unknown"); - printk(KERN_INFO PFX "CFE version: %s\n", cfe_version); - diff --git a/target/linux/brcm63xx/patches-3.9/313-MIPS-BCM63XX-rename-__dispatch_internal-to-__dispatc.patch b/target/linux/brcm63xx/patches-3.9/313-MIPS-BCM63XX-rename-__dispatch_internal-to-__dispatc.patch deleted file mode 100644 index b7b8065e80..0000000000 --- a/target/linux/brcm63xx/patches-3.9/313-MIPS-BCM63XX-rename-__dispatch_internal-to-__dispatc.patch +++ /dev/null @@ -1,51 +0,0 @@ -From 3bc62bd6e8c8a37d64cb797d24955711e98de15c Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 21 Mar 2013 17:05:15 +0100 -Subject: [PATCH 05/14] MIPS: BCM63XX: rename __dispatch_internal to - __dispatch_internal_32 - -Make it follow the same naming convention as the other functions. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 8 ++++---- - 1 file changed, 4 insertions(+), 4 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -19,7 +19,7 @@ - #include - #include - --static void __dispatch_internal(void) __maybe_unused; -+static void __dispatch_internal_32(void) __maybe_unused; - static void __dispatch_internal_64(void) __maybe_unused; - static void __internal_irq_mask_32(unsigned int irq) __maybe_unused; - static void __internal_irq_mask_64(unsigned int irq) __maybe_unused; -@@ -117,7 +117,7 @@ static void __internal_irq_unmask_64(uns - #endif - - #if irq_bits == 32 --#define dispatch_internal __dispatch_internal -+#define dispatch_internal __dispatch_internal_32 - #define internal_irq_mask __internal_irq_mask_32 - #define internal_irq_unmask __internal_irq_unmask_32 - #else -@@ -225,7 +225,7 @@ static void bcm63xx_init_irq(void) - } - - if (irq_bits == 32) { -- dispatch_internal = __dispatch_internal; -+ dispatch_internal = __dispatch_internal_32; - internal_irq_mask = __internal_irq_mask_32; - internal_irq_unmask = __internal_irq_unmask_32; - } else { -@@ -258,7 +258,7 @@ static inline void handle_internal(int i - * will resume the loop where it ended the last time we left this - * function. - */ --static void __dispatch_internal(void) -+static void __dispatch_internal_32(void) - { - u32 pending; - static int i; diff --git a/target/linux/brcm63xx/patches-3.9/314-MIPS-BCM63XX-replace-irq-dispatch-code-with-a-generi.patch b/target/linux/brcm63xx/patches-3.9/314-MIPS-BCM63XX-replace-irq-dispatch-code-with-a-generi.patch deleted file mode 100644 index 981e18540d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/314-MIPS-BCM63XX-replace-irq-dispatch-code-with-a-generi.patch +++ /dev/null @@ -1,167 +0,0 @@ -From 7447daa9a0768db157bbb64585f5411389712d59 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 18 Apr 2013 21:14:49 +0200 -Subject: [PATCH 06/14] MIPS: BCM63XX: replace irq dispatch code with a - generic version - -The generic version uses a variable length of u32 registers of u32/u64. -This allows easier support for longer registers without having to rewrite -verything. - -This "generic" version is not slower than the old version in the best case -(= i == next set bit), and twice as fast in the worst case in 64 bits. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 130 ++++++++++++++++++++--------------------------- - 1 file changed, 56 insertions(+), 74 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -258,47 +258,65 @@ static inline void handle_internal(int i - * will resume the loop where it ended the last time we left this - * function. - */ --static void __dispatch_internal_32(void) --{ -- u32 pending; -- static int i; -- -- pending = bcm_readl(irq_stat_addr) & bcm_readl(irq_mask_addr); -- -- if (!pending) -- return ; -- -- while (1) { -- int to_call = i; - -- i = (i + 1) & 0x1f; -- if (pending & (1 << to_call)) { -- handle_internal(to_call); -- break; -- } -- } -+#define BUILD_IPIC_INTERNAL(width) \ -+void __dispatch_internal_##width(void) \ -+{ \ -+ u32 pending[width / 32]; \ -+ unsigned int src, tgt; \ -+ bool irqs_pending = false; \ -+ static int i; \ -+ \ -+ /* read registers in reverse order */ \ -+ for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ -+ u32 val; \ -+ \ -+ val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \ -+ val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \ -+ pending[--tgt] = val; \ -+ \ -+ if (val) \ -+ irqs_pending = true; \ -+ } \ -+ \ -+ if (!irqs_pending) \ -+ return; \ -+ \ -+ while (1) { \ -+ int to_call = i; \ -+ \ -+ i = (i + 1) & (width - 1); \ -+ if (pending[to_call / 32] & (1 << (to_call & 0x1f))) { \ -+ handle_internal(to_call); \ -+ break; \ -+ } \ -+ } \ -+} \ -+ \ -+static void __internal_irq_mask_##width(unsigned int irq) \ -+{ \ -+ u32 val; \ -+ unsigned reg = (irq / 32) ^ (width/32 - 1); \ -+ unsigned bit = irq & 0x1f; \ -+ \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ val &= ~(1 << bit); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+} \ -+ \ -+static void __internal_irq_unmask_##width(unsigned int irq) \ -+{ \ -+ u32 val; \ -+ unsigned reg = (irq / 32) ^ (width/32 - 1); \ -+ unsigned bit = irq & 0x1f; \ -+ \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ val |= (1 << bit); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ - } - --static void __dispatch_internal_64(void) --{ -- u64 pending; -- static int i; -- -- pending = bcm_readq(irq_stat_addr) & bcm_readq(irq_mask_addr); -- -- if (!pending) -- return ; -- -- while (1) { -- int to_call = i; -- -- i = (i + 1) & 0x3f; -- if (pending & (1ull << to_call)) { -- handle_internal(to_call); -- break; -- } -- } --} -+BUILD_IPIC_INTERNAL(32); -+BUILD_IPIC_INTERNAL(64); - - asmlinkage void plat_irq_dispatch(void) - { -@@ -335,42 +353,6 @@ asmlinkage void plat_irq_dispatch(void) - * internal IRQs operations: only mask/unmask on PERF irq mask - * register. - */ --static void __internal_irq_mask_32(unsigned int irq) --{ -- u32 mask; -- -- mask = bcm_readl(irq_mask_addr); -- mask &= ~(1 << irq); -- bcm_writel(mask, irq_mask_addr); --} -- --static void __internal_irq_mask_64(unsigned int irq) --{ -- u64 mask; -- -- mask = bcm_readq(irq_mask_addr); -- mask &= ~(1ull << irq); -- bcm_writeq(mask, irq_mask_addr); --} -- --static void __internal_irq_unmask_32(unsigned int irq) --{ -- u32 mask; -- -- mask = bcm_readl(irq_mask_addr); -- mask |= (1 << irq); -- bcm_writel(mask, irq_mask_addr); --} -- --static void __internal_irq_unmask_64(unsigned int irq) --{ -- u64 mask; -- -- mask = bcm_readq(irq_mask_addr); -- mask |= (1ull << irq); -- bcm_writeq(mask, irq_mask_addr); --} -- - static void bcm63xx_internal_irq_mask(struct irq_data *d) - { - internal_irq_mask(d->irq - IRQ_INTERNAL_BASE); diff --git a/target/linux/brcm63xx/patches-3.9/315-MIPS-BCM63XX-append-cpu-number-to-irq_-stat-mask.patch b/target/linux/brcm63xx/patches-3.9/315-MIPS-BCM63XX-append-cpu-number-to-irq_-stat-mask.patch deleted file mode 100644 index b8ec372d73..0000000000 --- a/target/linux/brcm63xx/patches-3.9/315-MIPS-BCM63XX-append-cpu-number-to-irq_-stat-mask.patch +++ /dev/null @@ -1,279 +0,0 @@ -From 46442450ffb95a869894b0dfd1e5b4f973d4b4ee Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 25 Apr 2013 00:24:06 +0200 -Subject: [PATCH 07/14] MIPS: BCM63XX: append cpu number to irq_{stat,mask}* - -The SMP capable irq controllers have two interupt output pins which are -controlled through separate registers. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 86 ++++++++++----------- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 16 ++-- - 2 files changed, 51 insertions(+), 51 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -28,8 +28,8 @@ static void __internal_irq_unmask_64(uns - - #ifndef BCMCPU_RUNTIME_DETECT - #ifdef CONFIG_BCM63XX_CPU_3368 --#define irq_stat_reg PERF_IRQSTAT_3368_REG --#define irq_mask_reg PERF_IRQMASK_3368_REG -+#define irq_stat_reg0 PERF_IRQSTAT_3368_REG -+#define irq_mask_reg0 PERF_IRQMASK_3368_REG - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -39,8 +39,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6328 --#define irq_stat_reg PERF_IRQSTAT_6328_REG --#define irq_mask_reg PERF_IRQMASK_6328_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0) -+#define irq_mask_reg0 PERF_IRQMASK_6328_REG(0) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -50,8 +50,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 --#define irq_stat_reg PERF_IRQSTAT_6338_REG --#define irq_mask_reg PERF_IRQMASK_6338_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6338_REG -+#define irq_mask_reg0 PERF_IRQMASK_6338_REG - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -61,8 +61,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 --#define irq_stat_reg PERF_IRQSTAT_6345_REG --#define irq_mask_reg PERF_IRQMASK_6345_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6345_REG -+#define irq_mask_reg0 PERF_IRQMASK_6345_REG - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -72,8 +72,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 --#define irq_stat_reg PERF_IRQSTAT_6348_REG --#define irq_mask_reg PERF_IRQMASK_6348_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6348_REG -+#define irq_mask_reg0 PERF_IRQMASK_6348_REG - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -83,8 +83,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6358 --#define irq_stat_reg PERF_IRQSTAT_6358_REG --#define irq_mask_reg PERF_IRQMASK_6358_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6358_REG(0) -+#define irq_mask_reg0 PERF_IRQMASK_6358_REG(0) - #define irq_bits 32 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -94,8 +94,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6362 --#define irq_stat_reg PERF_IRQSTAT_6362_REG --#define irq_mask_reg PERF_IRQMASK_6362_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6362_REG(0) -+#define irq_mask_reg0 PERF_IRQMASK_6362_REG(0) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -105,8 +105,8 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6368 --#define irq_stat_reg PERF_IRQSTAT_6368_REG --#define irq_mask_reg PERF_IRQMASK_6368_REG -+#define irq_stat_reg0 PERF_IRQSTAT_6368_REG(0) -+#define irq_mask_reg0 PERF_IRQMASK_6368_REG(0) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -126,15 +126,15 @@ static void __internal_irq_unmask_64(uns - #define internal_irq_unmask __internal_irq_unmask_64 - #endif - --#define irq_stat_addr (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg) --#define irq_mask_addr (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg) -+#define irq_stat_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg0) -+#define irq_mask_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg0) - - static inline void bcm63xx_init_irq(void) - { - } - #else /* ! BCMCPU_RUNTIME_DETECT */ - --static u32 irq_stat_addr, irq_mask_addr; -+static u32 irq_stat_addr0, irq_mask_addr0; - static void (*dispatch_internal)(void); - static int is_ext_irq_cascaded; - static unsigned int ext_irq_count; -@@ -147,20 +147,20 @@ static void bcm63xx_init_irq(void) - { - int irq_bits; - -- irq_stat_addr = bcm63xx_regset_address(RSET_PERF); -- irq_mask_addr = bcm63xx_regset_address(RSET_PERF); -+ irq_stat_addr0 = bcm63xx_regset_address(RSET_PERF); -+ irq_mask_addr0 = bcm63xx_regset_address(RSET_PERF); - - switch (bcm63xx_get_cpu_id()) { - case BCM3368_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_3368_REG; -- irq_mask_addr += PERF_IRQMASK_3368_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_3368_REG; -+ irq_mask_addr0 += PERF_IRQMASK_3368_REG; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368; - break; - case BCM6328_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6328_REG; -- irq_mask_addr += PERF_IRQMASK_6328_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6328_REG(0); -+ irq_mask_addr0 += PERF_IRQMASK_6328_REG(0); - irq_bits = 64; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -169,29 +169,29 @@ static void bcm63xx_init_irq(void) - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6328; - break; - case BCM6338_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6338_REG; -- irq_mask_addr += PERF_IRQMASK_6338_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6338_REG; -+ irq_mask_addr0 += PERF_IRQMASK_6338_REG; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338; - break; - case BCM6345_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6345_REG; -- irq_mask_addr += PERF_IRQMASK_6345_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6345_REG; -+ irq_mask_addr0 += PERF_IRQMASK_6345_REG; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345; - break; - case BCM6348_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6348_REG; -- irq_mask_addr += PERF_IRQMASK_6348_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6348_REG; -+ irq_mask_addr0 += PERF_IRQMASK_6348_REG; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6348; - break; - case BCM6358_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6358_REG; -- irq_mask_addr += PERF_IRQMASK_6358_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6358_REG(0); -+ irq_mask_addr0 += PERF_IRQMASK_6358_REG(0); - irq_bits = 32; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -200,8 +200,8 @@ static void bcm63xx_init_irq(void) - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358; - break; - case BCM6362_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6362_REG; -- irq_mask_addr += PERF_IRQMASK_6362_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6362_REG(0); -+ irq_mask_addr0 += PERF_IRQMASK_6362_REG(0); - irq_bits = 64; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -210,8 +210,8 @@ static void bcm63xx_init_irq(void) - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362; - break; - case BCM6368_CPU_ID: -- irq_stat_addr += PERF_IRQSTAT_6368_REG; -- irq_mask_addr += PERF_IRQMASK_6368_REG; -+ irq_stat_addr0 += PERF_IRQSTAT_6368_REG(0); -+ irq_mask_addr0 += PERF_IRQMASK_6368_REG(0); - irq_bits = 64; - ext_irq_count = 6; - is_ext_irq_cascaded = 1; -@@ -271,8 +271,8 @@ void __dispatch_internal_##width(void) - for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ - u32 val; \ - \ -- val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \ -- val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \ -+ val = bcm_readl(irq_stat_addr0 + src * sizeof(u32)); \ -+ val &= bcm_readl(irq_mask_addr0 + src * sizeof(u32)); \ - pending[--tgt] = val; \ - \ - if (val) \ -@@ -299,9 +299,9 @@ static void __internal_irq_mask_##width( - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - \ -- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \ - val &= ~(1 << bit); \ -- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \ - } \ - \ - static void __internal_irq_unmask_##width(unsigned int irq) \ -@@ -310,9 +310,9 @@ static void __internal_irq_unmask_##widt - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - \ -- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \ - val |= (1 << bit); \ -- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \ - } - - BUILD_IPIC_INTERNAL(32); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -215,23 +215,23 @@ - - /* Interrupt Mask register */ - #define PERF_IRQMASK_3368_REG 0xc --#define PERF_IRQMASK_6328_REG 0x20 -+#define PERF_IRQMASK_6328_REG(x) (0x20 + (x) * 0x10) - #define PERF_IRQMASK_6338_REG 0xc - #define PERF_IRQMASK_6345_REG 0xc - #define PERF_IRQMASK_6348_REG 0xc --#define PERF_IRQMASK_6358_REG 0xc --#define PERF_IRQMASK_6362_REG 0x20 --#define PERF_IRQMASK_6368_REG 0x20 -+#define PERF_IRQMASK_6358_REG(x) (0xc + (x) * 0x2c) -+#define PERF_IRQMASK_6362_REG(x) (0x20 + (x) * 0x10) -+#define PERF_IRQMASK_6368_REG(x) (0x20 + (x) * 0x10) - - /* Interrupt Status register */ - #define PERF_IRQSTAT_3368_REG 0x10 --#define PERF_IRQSTAT_6328_REG 0x28 -+#define PERF_IRQSTAT_6328_REG(x) (0x28 + (x) * 0x10) - #define PERF_IRQSTAT_6338_REG 0x10 - #define PERF_IRQSTAT_6345_REG 0x10 - #define PERF_IRQSTAT_6348_REG 0x10 --#define PERF_IRQSTAT_6358_REG 0x10 --#define PERF_IRQSTAT_6362_REG 0x28 --#define PERF_IRQSTAT_6368_REG 0x28 -+#define PERF_IRQSTAT_6358_REG(x) (0x10 + (x) * 0x2c) -+#define PERF_IRQSTAT_6362_REG(x) (0x28 + (x) * 0x10) -+#define PERF_IRQSTAT_6368_REG(x) (0x28 + (x) * 0x10) - - /* External Interrupt Configuration register */ - #define PERF_EXTIRQ_CFG_REG_3368 0x14 diff --git a/target/linux/brcm63xx/patches-3.9/316-MIPS-BCM63XX-populate-irq_-stat-mask-_addr-for-secon.patch b/target/linux/brcm63xx/patches-3.9/316-MIPS-BCM63XX-populate-irq_-stat-mask-_addr-for-secon.patch deleted file mode 100644 index bd3ca8023c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/316-MIPS-BCM63XX-populate-irq_-stat-mask-_addr-for-secon.patch +++ /dev/null @@ -1,186 +0,0 @@ -From 1a1769d6268c93b042f635b31b43024fea7feb30 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 25 Apr 2013 00:31:29 +0200 -Subject: [PATCH 08/14] MIPS: BCM63XX: populate irq_{stat,mask}_addr for - second pin - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 43 ++++++++++++++++++++++++++++++++++++++++++- - 1 file changed, 42 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -30,6 +30,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_3368 - #define irq_stat_reg0 PERF_IRQSTAT_3368_REG - #define irq_mask_reg0 PERF_IRQMASK_3368_REG -+#define irq_stat_reg1 0 -+#define irq_mask_reg1 0 - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -41,6 +43,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6328 - #define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0) - #define irq_mask_reg0 PERF_IRQMASK_6328_REG(0) -+#define irq_stat_reg1 PERF_IRQSTAT_6328_REG(1) -+#define irq_mask_reg1 PERF_IRQMASK_6328_REG(1) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -52,6 +56,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6338 - #define irq_stat_reg0 PERF_IRQSTAT_6338_REG - #define irq_mask_reg0 PERF_IRQMASK_6338_REG -+#define irq_stat_reg1 0 -+#define irq_mask_reg1 0 - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -63,6 +69,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6345 - #define irq_stat_reg0 PERF_IRQSTAT_6345_REG - #define irq_mask_reg0 PERF_IRQMASK_6345_REG -+#define irq_stat_reg1 0 -+#define irq_mask_reg1 0 - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -74,6 +82,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6348 - #define irq_stat_reg0 PERF_IRQSTAT_6348_REG - #define irq_mask_reg0 PERF_IRQMASK_6348_REG -+#define irq_stat_reg1 0 -+#define irq_mask_reg1 0 - #define irq_bits 32 - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 -@@ -85,6 +95,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6358 - #define irq_stat_reg0 PERF_IRQSTAT_6358_REG(0) - #define irq_mask_reg0 PERF_IRQMASK_6358_REG(0) -+#define irq_stat_reg1 PERF_IRQSTAT_6358_REG(1) -+#define irq_mask_reg1 PERF_IRQMASK_6358_REG(1) - #define irq_bits 32 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -96,6 +108,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6362 - #define irq_stat_reg0 PERF_IRQSTAT_6362_REG(0) - #define irq_mask_reg0 PERF_IRQMASK_6362_REG(0) -+#define irq_stat_reg1 PERF_IRQSTAT_6362_REG(1) -+#define irq_mask_reg1 PERF_IRQMASK_6362_REG(1) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -107,6 +121,8 @@ static void __internal_irq_unmask_64(uns - #ifdef CONFIG_BCM63XX_CPU_6368 - #define irq_stat_reg0 PERF_IRQSTAT_6368_REG(0) - #define irq_mask_reg0 PERF_IRQMASK_6368_REG(0) -+#define irq_stat_reg1 PERF_IRQSTAT_6368_REG(1) -+#define irq_mask_reg1 PERF_IRQMASK_6368_REG(1) - #define irq_bits 64 - #define is_ext_irq_cascaded 1 - #define ext_irq_start (BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE) -@@ -128,13 +144,20 @@ static void __internal_irq_unmask_64(uns - - #define irq_stat_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg0) - #define irq_mask_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg0) -+#if (irq_stat_reg1 > 0) && (irq_mask_reg1 > 0) -+#define irq_stat_addr1 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg1) -+#define irq_mask_addr1 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg1) -+#else -+#define irq_stat_addr1 0 -+#define irq_mask_addr1 0 -+#endif - - static inline void bcm63xx_init_irq(void) - { - } - #else /* ! BCMCPU_RUNTIME_DETECT */ - --static u32 irq_stat_addr0, irq_mask_addr0; -+static u32 irq_stat_addr0, irq_mask_addr0, irq_stat_addr1, irq_mask_addr1; - static void (*dispatch_internal)(void); - static int is_ext_irq_cascaded; - static unsigned int ext_irq_count; -@@ -149,11 +172,15 @@ static void bcm63xx_init_irq(void) - - irq_stat_addr0 = bcm63xx_regset_address(RSET_PERF); - irq_mask_addr0 = bcm63xx_regset_address(RSET_PERF); -+ irq_stat_addr1 = bcm63xx_regset_address(RSET_PERF); -+ irq_mask_addr1 = bcm63xx_regset_address(RSET_PERF); - - switch (bcm63xx_get_cpu_id()) { - case BCM3368_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_3368_REG; - irq_mask_addr0 += PERF_IRQMASK_3368_REG; -+ irq_stat_addr1 = 0; -+ irq_stat_addr1 = 0; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368; -@@ -161,6 +188,8 @@ static void bcm63xx_init_irq(void) - case BCM6328_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6328_REG(0); - irq_mask_addr0 += PERF_IRQMASK_6328_REG(0); -+ irq_stat_addr1 += PERF_IRQSTAT_6328_REG(1); -+ irq_stat_addr1 += PERF_IRQMASK_6328_REG(1); - irq_bits = 64; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -171,6 +200,8 @@ static void bcm63xx_init_irq(void) - case BCM6338_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6338_REG; - irq_mask_addr0 += PERF_IRQMASK_6338_REG; -+ irq_stat_addr1 = 0; -+ irq_mask_addr1 = 0; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338; -@@ -178,6 +209,8 @@ static void bcm63xx_init_irq(void) - case BCM6345_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6345_REG; - irq_mask_addr0 += PERF_IRQMASK_6345_REG; -+ irq_stat_addr1 = 0; -+ irq_mask_addr1 = 0; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345; -@@ -185,6 +218,8 @@ static void bcm63xx_init_irq(void) - case BCM6348_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6348_REG; - irq_mask_addr0 += PERF_IRQMASK_6348_REG; -+ irq_stat_addr1 = 0; -+ irq_mask_addr1 = 0; - irq_bits = 32; - ext_irq_count = 4; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6348; -@@ -192,6 +227,8 @@ static void bcm63xx_init_irq(void) - case BCM6358_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6358_REG(0); - irq_mask_addr0 += PERF_IRQMASK_6358_REG(0); -+ irq_stat_addr1 += PERF_IRQSTAT_6358_REG(1); -+ irq_mask_addr1 += PERF_IRQMASK_6358_REG(1); - irq_bits = 32; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -202,6 +239,8 @@ static void bcm63xx_init_irq(void) - case BCM6362_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6362_REG(0); - irq_mask_addr0 += PERF_IRQMASK_6362_REG(0); -+ irq_stat_addr1 += PERF_IRQSTAT_6362_REG(1); -+ irq_mask_addr1 += PERF_IRQMASK_6362_REG(1); - irq_bits = 64; - ext_irq_count = 4; - is_ext_irq_cascaded = 1; -@@ -212,6 +251,8 @@ static void bcm63xx_init_irq(void) - case BCM6368_CPU_ID: - irq_stat_addr0 += PERF_IRQSTAT_6368_REG(0); - irq_mask_addr0 += PERF_IRQMASK_6368_REG(0); -+ irq_stat_addr1 += PERF_IRQSTAT_6368_REG(1); -+ irq_mask_addr1 += PERF_IRQMASK_6368_REG(1); - irq_bits = 64; - ext_irq_count = 6; - is_ext_irq_cascaded = 1; diff --git a/target/linux/brcm63xx/patches-3.9/317-MIPS-BCM63XX-use-a-helper-for-getting-the-right-regi.patch b/target/linux/brcm63xx/patches-3.9/317-MIPS-BCM63XX-use-a-helper-for-getting-the-right-regi.patch deleted file mode 100644 index e3377313f6..0000000000 --- a/target/linux/brcm63xx/patches-3.9/317-MIPS-BCM63XX-use-a-helper-for-getting-the-right-regi.patch +++ /dev/null @@ -1,80 +0,0 @@ -From 353f07637d82cf485a9319d203a6ed9b38590526 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 25 Apr 2013 15:35:12 +0200 -Subject: [PATCH 09/14] MIPS: BCM63XX: use a helper for getting the right - register address - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 30 ++++++++++++++++++++++++------ - 1 file changed, 24 insertions(+), 6 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -284,6 +284,20 @@ static inline u32 get_ext_irq_perf_reg(i - return ext_irq_cfg_reg2; - } - -+static inline u32 get_irq_stat_addr(int pin) -+{ -+ if (pin == 0) -+ return irq_stat_addr0; -+ return irq_stat_addr1; -+} -+ -+static inline u32 get_irq_mask_addr(int pin) -+{ -+ if (pin == 0) -+ return irq_mask_addr0; -+ return irq_mask_addr1; -+} -+ - static inline void handle_internal(int intbit) - { - if (is_ext_irq_cascaded && -@@ -307,13 +321,15 @@ void __dispatch_internal_##width(void) - unsigned int src, tgt; \ - bool irqs_pending = false; \ - static int i; \ -+ u32 irq_stat_addr = get_irq_stat_addr(0); \ -+ u32 irq_mask_addr = get_irq_mask_addr(0); \ - \ - /* read registers in reverse order */ \ - for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ - u32 val; \ - \ -- val = bcm_readl(irq_stat_addr0 + src * sizeof(u32)); \ -- val &= bcm_readl(irq_mask_addr0 + src * sizeof(u32)); \ -+ val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \ -+ val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \ - pending[--tgt] = val; \ - \ - if (val) \ -@@ -339,10 +355,11 @@ static void __internal_irq_mask_##width( - u32 val; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ -+ u32 irq_mask_addr = get_irq_mask_addr(0); \ - \ -- val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ - val &= ~(1 << bit); \ -- bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ - } \ - \ - static void __internal_irq_unmask_##width(unsigned int irq) \ -@@ -350,10 +367,11 @@ static void __internal_irq_unmask_##widt - u32 val; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ -+ u32 irq_mask_addr = get_irq_mask_addr(0); \ - \ -- val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ - val |= (1 << bit); \ -- bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ - } - - BUILD_IPIC_INTERNAL(32); diff --git a/target/linux/brcm63xx/patches-3.9/318-MIPS-BCM63XX-add-cpu-argument-to-dispatch-internal.patch b/target/linux/brcm63xx/patches-3.9/318-MIPS-BCM63XX-add-cpu-argument-to-dispatch-internal.patch deleted file mode 100644 index 18377549a9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/318-MIPS-BCM63XX-add-cpu-argument-to-dispatch-internal.patch +++ /dev/null @@ -1,73 +0,0 @@ -From b6b668f780d62d41bc14bc7baba1692e17cabf84 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 26 Apr 2013 11:21:16 +0200 -Subject: [PATCH 10/14] MIPS: BCM63XX: add cpu argument to dispatch internal - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 21 +++++++++++---------- - 1 file changed, 11 insertions(+), 10 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -19,8 +19,8 @@ - #include - #include - --static void __dispatch_internal_32(void) __maybe_unused; --static void __dispatch_internal_64(void) __maybe_unused; -+static void __dispatch_internal_32(int cpu) __maybe_unused; -+static void __dispatch_internal_64(int cpu) __maybe_unused; - static void __internal_irq_mask_32(unsigned int irq) __maybe_unused; - static void __internal_irq_mask_64(unsigned int irq) __maybe_unused; - static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused; -@@ -158,7 +158,7 @@ static inline void bcm63xx_init_irq(void - #else /* ! BCMCPU_RUNTIME_DETECT */ - - static u32 irq_stat_addr0, irq_mask_addr0, irq_stat_addr1, irq_mask_addr1; --static void (*dispatch_internal)(void); -+static void (*dispatch_internal)(int cpu); - static int is_ext_irq_cascaded; - static unsigned int ext_irq_count; - static unsigned int ext_irq_start, ext_irq_end; -@@ -315,14 +315,15 @@ static inline void handle_internal(int i - */ - - #define BUILD_IPIC_INTERNAL(width) \ --void __dispatch_internal_##width(void) \ -+void __dispatch_internal_##width(int cpu) \ - { \ - u32 pending[width / 32]; \ - unsigned int src, tgt; \ - bool irqs_pending = false; \ -- static int i; \ -- u32 irq_stat_addr = get_irq_stat_addr(0); \ -- u32 irq_mask_addr = get_irq_mask_addr(0); \ -+ static int i[NR_CPUS]; \ -+ u32 irq_stat_addr = get_irq_stat_addr(cpu); \ -+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \ -+ int *next = &i[cpu]; \ - \ - /* read registers in reverse order */ \ - for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ -@@ -340,9 +341,9 @@ void __dispatch_internal_##width(void) - return; \ - \ - while (1) { \ -- int to_call = i; \ -+ int to_call = *next; \ - \ -- i = (i + 1) & (width - 1); \ -+ *next = (*next + 1) & (width - 1); \ - if (pending[to_call / 32] & (1 << (to_call & 0x1f))) { \ - handle_internal(to_call); \ - break; \ -@@ -394,7 +395,7 @@ asmlinkage void plat_irq_dispatch(void) - if (cause & CAUSEF_IP1) - do_IRQ(1); - if (cause & CAUSEF_IP2) -- dispatch_internal(); -+ dispatch_internal(0); - if (!is_ext_irq_cascaded) { - if (cause & CAUSEF_IP3) - do_IRQ(IRQ_EXT_0); diff --git a/target/linux/brcm63xx/patches-3.9/319-MIPS-BCM63XX-protect-irq-register-accesses.patch b/target/linux/brcm63xx/patches-3.9/319-MIPS-BCM63XX-protect-irq-register-accesses.patch deleted file mode 100644 index 81b6eeef5a..0000000000 --- a/target/linux/brcm63xx/patches-3.9/319-MIPS-BCM63XX-protect-irq-register-accesses.patch +++ /dev/null @@ -1,158 +0,0 @@ -From 05e32e9dc84ee96728596c0b8b86de7eae8de229 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 21 Apr 2013 15:38:56 +0200 -Subject: [PATCH 11/14] MIPS: BCM63XX: protect irq register accesses - ---- - arch/mips/bcm63xx/irq.c | 26 ++++++++++++++++++++++++++ - 1 file changed, 26 insertions(+) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -12,6 +12,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -26,6 +27,9 @@ static void __internal_irq_mask_64(unsig - static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused; - static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused; - -+static DEFINE_SPINLOCK(ipic_lock); -+static DEFINE_SPINLOCK(epic_lock); -+ - #ifndef BCMCPU_RUNTIME_DETECT - #ifdef CONFIG_BCM63XX_CPU_3368 - #define irq_stat_reg0 PERF_IRQSTAT_3368_REG -@@ -324,8 +328,10 @@ void __dispatch_internal_##width(int cpu - u32 irq_stat_addr = get_irq_stat_addr(cpu); \ - u32 irq_mask_addr = get_irq_mask_addr(cpu); \ - int *next = &i[cpu]; \ -+ unsigned long flags; \ - \ - /* read registers in reverse order */ \ -+ spin_lock_irqsave(&ipic_lock, flags); \ - for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ - u32 val; \ - \ -@@ -336,6 +342,7 @@ void __dispatch_internal_##width(int cpu - if (val) \ - irqs_pending = true; \ - } \ -+ spin_unlock_irqrestore(&ipic_lock, flags); \ - \ - if (!irqs_pending) \ - return; \ -@@ -357,10 +364,13 @@ static void __internal_irq_mask_##width( - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - u32 irq_mask_addr = get_irq_mask_addr(0); \ -+ unsigned long flags; \ - \ -+ spin_lock_irqsave(&ipic_lock, flags); \ - val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ - val &= ~(1 << bit); \ - bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ spin_unlock_irqrestore(&ipic_lock, flags); \ - } \ - \ - static void __internal_irq_unmask_##width(unsigned int irq) \ -@@ -369,10 +379,13 @@ static void __internal_irq_unmask_##widt - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - u32 irq_mask_addr = get_irq_mask_addr(0); \ -+ unsigned long flags; \ - \ -+ spin_lock_irqsave(&ipic_lock, flags); \ - val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ - val |= (1 << bit); \ - bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ spin_unlock_irqrestore(&ipic_lock, flags); \ - } - - BUILD_IPIC_INTERNAL(32); -@@ -431,8 +444,10 @@ static void bcm63xx_external_irq_mask(st - { - unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; - u32 reg, regaddr; -+ unsigned long flags; - - regaddr = get_ext_irq_perf_reg(irq); -+ spin_lock_irqsave(&epic_lock, flags); - reg = bcm_perf_readl(regaddr); - - if (BCMCPU_IS_6348()) -@@ -441,6 +456,8 @@ static void bcm63xx_external_irq_mask(st - reg &= ~EXTIRQ_CFG_MASK(irq % 4); - - bcm_perf_writel(reg, regaddr); -+ spin_unlock_irqrestore(&epic_lock, flags); -+ - if (is_ext_irq_cascaded) - internal_irq_mask(irq + ext_irq_start); - } -@@ -449,8 +466,10 @@ static void bcm63xx_external_irq_unmask( - { - unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; - u32 reg, regaddr; -+ unsigned long flags; - - regaddr = get_ext_irq_perf_reg(irq); -+ spin_lock_irqsave(&epic_lock, flags); - reg = bcm_perf_readl(regaddr); - - if (BCMCPU_IS_6348()) -@@ -459,6 +478,7 @@ static void bcm63xx_external_irq_unmask( - reg |= EXTIRQ_CFG_MASK(irq % 4); - - bcm_perf_writel(reg, regaddr); -+ spin_unlock_irqrestore(&epic_lock, flags); - - if (is_ext_irq_cascaded) - internal_irq_unmask(irq + ext_irq_start); -@@ -468,8 +488,10 @@ static void bcm63xx_external_irq_clear(s - { - unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; - u32 reg, regaddr; -+ unsigned long flags; - - regaddr = get_ext_irq_perf_reg(irq); -+ spin_lock_irqsave(&epic_lock, flags); - reg = bcm_perf_readl(regaddr); - - if (BCMCPU_IS_6348()) -@@ -478,6 +500,7 @@ static void bcm63xx_external_irq_clear(s - reg |= EXTIRQ_CFG_CLEAR(irq % 4); - - bcm_perf_writel(reg, regaddr); -+ spin_unlock_irqrestore(&epic_lock, flags); - } - - static int bcm63xx_external_irq_set_type(struct irq_data *d, -@@ -486,6 +509,7 @@ static int bcm63xx_external_irq_set_type - unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; - u32 reg, regaddr; - int levelsense, sense, bothedge; -+ unsigned long flags; - - flow_type &= IRQ_TYPE_SENSE_MASK; - -@@ -520,6 +544,7 @@ static int bcm63xx_external_irq_set_type - } - - regaddr = get_ext_irq_perf_reg(irq); -+ spin_lock_irqsave(&epic_lock, flags); - reg = bcm_perf_readl(regaddr); - irq %= 4; - -@@ -564,6 +589,7 @@ static int bcm63xx_external_irq_set_type - } - - bcm_perf_writel(reg, regaddr); -+ spin_unlock_irqrestore(&epic_lock, flags); - - irqd_set_trigger_type(d, flow_type); - if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) diff --git a/target/linux/brcm63xx/patches-3.9/320-MIPS-BCM63XX-wire-up-the-second-CPU-s-irq-line.patch b/target/linux/brcm63xx/patches-3.9/320-MIPS-BCM63XX-wire-up-the-second-CPU-s-irq-line.patch deleted file mode 100644 index 2d92c24635..0000000000 --- a/target/linux/brcm63xx/patches-3.9/320-MIPS-BCM63XX-wire-up-the-second-CPU-s-irq-line.patch +++ /dev/null @@ -1,100 +0,0 @@ -From 70c33fe0df8d14e40f3ca92ce56a668d66184858 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 26 Apr 2013 12:03:15 +0200 -Subject: [PATCH 12/14] MIPS: BCM63XX: wire up the second cpu's irq line - ---- - arch/mips/bcm63xx/irq.c | 50 ++++++++++++++++++++++++++++++++++++++--------- - 1 file changed, 41 insertions(+), 9 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -363,13 +363,20 @@ static void __internal_irq_mask_##width( - u32 val; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ -- u32 irq_mask_addr = get_irq_mask_addr(0); \ - unsigned long flags; \ -+ int cpu; \ - \ - spin_lock_irqsave(&ipic_lock, flags); \ -- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -- val &= ~(1 << bit); \ -- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ for_each_present_cpu(cpu) { \ -+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \ -+ \ -+ if (!irq_mask_addr) \ -+ break; \ -+ \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ val &= ~(1 << bit); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ } \ - spin_unlock_irqrestore(&ipic_lock, flags); \ - } \ - \ -@@ -378,13 +385,23 @@ static void __internal_irq_unmask_##widt - u32 val; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ -- u32 irq_mask_addr = get_irq_mask_addr(0); \ - unsigned long flags; \ -+ int cpu; \ - \ - spin_lock_irqsave(&ipic_lock, flags); \ -- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -- val |= (1 << bit); \ -- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ for_each_present_cpu(cpu) { \ -+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \ -+ \ -+ if (!irq_mask_addr) \ -+ break; \ -+ \ -+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -+ if (cpu_online(cpu)) \ -+ val |= (1 << bit); \ -+ else \ -+ val &= ~(1 << bit); \ -+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \ -+ } \ - spin_unlock_irqrestore(&ipic_lock, flags); \ - } - -@@ -409,7 +426,10 @@ asmlinkage void plat_irq_dispatch(void) - do_IRQ(1); - if (cause & CAUSEF_IP2) - dispatch_internal(0); -- if (!is_ext_irq_cascaded) { -+ if (is_ext_irq_cascaded) { -+ if (cause & CAUSEF_IP3) -+ dispatch_internal(1); -+ } else { - if (cause & CAUSEF_IP3) - do_IRQ(IRQ_EXT_0); - if (cause & CAUSEF_IP4) -@@ -622,6 +642,14 @@ static struct irqaction cpu_ip2_cascade_ - .flags = IRQF_NO_THREAD, - }; - -+#ifdef CONFIG_SMP -+static struct irqaction cpu_ip3_cascade_action = { -+ .handler = no_action, -+ .name = "cascade_ip3", -+ .flags = IRQF_NO_THREAD, -+}; -+#endif -+ - static struct irqaction cpu_ext_cascade_action = { - .handler = no_action, - .name = "cascade_extirq", -@@ -648,4 +676,8 @@ void __init arch_init_irq(void) - } - - setup_irq(MIPS_CPU_IRQ_BASE + 2, &cpu_ip2_cascade_action); -+#ifdef CONFIG_SMP -+ if (is_ext_irq_cascaded) -+ setup_irq(MIPS_CPU_IRQ_BASE + 3, &cpu_ip3_cascade_action); -+#endif - } diff --git a/target/linux/brcm63xx/patches-3.9/321-MIPS-BCM63XX-use-irq_desc-as-argument-for-un-mask.patch b/target/linux/brcm63xx/patches-3.9/321-MIPS-BCM63XX-use-irq_desc-as-argument-for-un-mask.patch deleted file mode 100644 index 803d925f34..0000000000 --- a/target/linux/brcm63xx/patches-3.9/321-MIPS-BCM63XX-use-irq_desc-as-argument-for-un-mask.patch +++ /dev/null @@ -1,98 +0,0 @@ -From 0e692ab15a69ac4534c18e67ed3cb7685f728037 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 30 Apr 2013 11:26:53 +0200 -Subject: [PATCH 13/14] MIPS: BCM63XX: use irq_desc as argument for (un)mask - -In preparation for applying affinity, use the irq descriptor as the -argument for (un)mask. - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 26 ++++++++++++++------------ - 1 file changed, 14 insertions(+), 12 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -22,10 +22,10 @@ - - static void __dispatch_internal_32(int cpu) __maybe_unused; - static void __dispatch_internal_64(int cpu) __maybe_unused; --static void __internal_irq_mask_32(unsigned int irq) __maybe_unused; --static void __internal_irq_mask_64(unsigned int irq) __maybe_unused; --static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused; --static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused; -+static void __internal_irq_mask_32(struct irq_data *d) __maybe_unused; -+static void __internal_irq_mask_64(struct irq_data *d) __maybe_unused; -+static void __internal_irq_unmask_32(struct irq_data *d) __maybe_unused; -+static void __internal_irq_unmask_64(struct irq_data *d) __maybe_unused; - - static DEFINE_SPINLOCK(ipic_lock); - static DEFINE_SPINLOCK(epic_lock); -@@ -167,8 +167,8 @@ static int is_ext_irq_cascaded; - static unsigned int ext_irq_count; - static unsigned int ext_irq_start, ext_irq_end; - static unsigned int ext_irq_cfg_reg1, ext_irq_cfg_reg2; --static void (*internal_irq_mask)(unsigned int irq); --static void (*internal_irq_unmask)(unsigned int irq); -+static void (*internal_irq_mask)(struct irq_data *d); -+static void (*internal_irq_unmask)(struct irq_data *d); - - static void bcm63xx_init_irq(void) - { -@@ -358,9 +358,10 @@ void __dispatch_internal_##width(int cpu - } \ - } \ - \ --static void __internal_irq_mask_##width(unsigned int irq) \ -+static void __internal_irq_mask_##width(struct irq_data *d) \ - { \ - u32 val; \ -+ unsigned irq = d->irq - IRQ_INTERNAL_BASE; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - unsigned long flags; \ -@@ -380,9 +381,10 @@ static void __internal_irq_mask_##width( - spin_unlock_irqrestore(&ipic_lock, flags); \ - } \ - \ --static void __internal_irq_unmask_##width(unsigned int irq) \ -+static void __internal_irq_unmask_##width(struct irq_data *d) \ - { \ - u32 val; \ -+ unsigned irq = d->irq - IRQ_INTERNAL_BASE; \ - unsigned reg = (irq / 32) ^ (width/32 - 1); \ - unsigned bit = irq & 0x1f; \ - unsigned long flags; \ -@@ -448,12 +450,12 @@ asmlinkage void plat_irq_dispatch(void) - */ - static void bcm63xx_internal_irq_mask(struct irq_data *d) - { -- internal_irq_mask(d->irq - IRQ_INTERNAL_BASE); -+ internal_irq_mask(d); - } - - static void bcm63xx_internal_irq_unmask(struct irq_data *d) - { -- internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE); -+ internal_irq_unmask(d); - } - - /* -@@ -479,7 +481,7 @@ static void bcm63xx_external_irq_mask(st - spin_unlock_irqrestore(&epic_lock, flags); - - if (is_ext_irq_cascaded) -- internal_irq_mask(irq + ext_irq_start); -+ internal_irq_mask(irq_get_irq_data(irq + ext_irq_start)); - } - - static void bcm63xx_external_irq_unmask(struct irq_data *d) -@@ -501,7 +503,7 @@ static void bcm63xx_external_irq_unmask( - spin_unlock_irqrestore(&epic_lock, flags); - - if (is_ext_irq_cascaded) -- internal_irq_unmask(irq + ext_irq_start); -+ internal_irq_unmask(irq_get_irq_data(irq + ext_irq_start)); - } - - static void bcm63xx_external_irq_clear(struct irq_data *d) diff --git a/target/linux/brcm63xx/patches-3.9/322-MIPS-BCM63XX-allow-setting-affinity-for-IPIC.patch b/target/linux/brcm63xx/patches-3.9/322-MIPS-BCM63XX-allow-setting-affinity-for-IPIC.patch deleted file mode 100644 index c89a344ff9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/322-MIPS-BCM63XX-allow-setting-affinity-for-IPIC.patch +++ /dev/null @@ -1,124 +0,0 @@ -From 9e341df1f67c3c64dc5ac668a30bbb6b5ab5f2b4 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 26 Apr 2013 12:06:03 +0200 -Subject: [PATCH 14/14] MIPS: BCM63XX: allow setting affinity for IPIC - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/irq.c | 49 +++++++++++++++++++++++++++++++++++++++-------- - 1 file changed, 41 insertions(+), 8 deletions(-) - ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -24,8 +24,10 @@ static void __dispatch_internal_32(int c - static void __dispatch_internal_64(int cpu) __maybe_unused; - static void __internal_irq_mask_32(struct irq_data *d) __maybe_unused; - static void __internal_irq_mask_64(struct irq_data *d) __maybe_unused; --static void __internal_irq_unmask_32(struct irq_data *d) __maybe_unused; --static void __internal_irq_unmask_64(struct irq_data *d) __maybe_unused; -+static void __internal_irq_unmask_32(struct irq_data *d, -+ const struct cpumask *mask) __maybe_unused; -+static void __internal_irq_unmask_64(struct irq_data *d, -+ const struct cpumask *mask) __maybe_unused; - - static DEFINE_SPINLOCK(ipic_lock); - static DEFINE_SPINLOCK(epic_lock); -@@ -168,7 +170,7 @@ static unsigned int ext_irq_count; - static unsigned int ext_irq_start, ext_irq_end; - static unsigned int ext_irq_cfg_reg1, ext_irq_cfg_reg2; - static void (*internal_irq_mask)(struct irq_data *d); --static void (*internal_irq_unmask)(struct irq_data *d); -+static void (*internal_irq_unmask)(struct irq_data *d, const struct cpumask *m); - - static void bcm63xx_init_irq(void) - { -@@ -311,6 +313,20 @@ static inline void handle_internal(int i - do_IRQ(intbit + IRQ_INTERNAL_BASE); - } - -+static inline int enable_irq_for_cpu(int cpu, struct irq_data *d, -+ const struct cpumask *m) -+{ -+ bool enable = cpu_online(cpu); -+#ifdef CONFIG_SMP -+ -+ if (m) -+ enable &= cpu_isset(cpu, *m); -+ else if (irqd_affinity_was_set(d)) -+ enable &= cpu_isset(cpu, *d->affinity); -+#endif -+ return enable; -+} -+ - /* - * dispatch internal devices IRQ (uart, enet, watchdog, ...). do not - * prioritize any interrupt relatively to another. the static counter -@@ -381,7 +397,8 @@ static void __internal_irq_mask_##width( - spin_unlock_irqrestore(&ipic_lock, flags); \ - } \ - \ --static void __internal_irq_unmask_##width(struct irq_data *d) \ -+static void __internal_irq_unmask_##width(struct irq_data *d, \ -+ const struct cpumask *m) \ - { \ - u32 val; \ - unsigned irq = d->irq - IRQ_INTERNAL_BASE; \ -@@ -398,7 +415,7 @@ static void __internal_irq_unmask_##widt - break; \ - \ - val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \ -- if (cpu_online(cpu)) \ -+ if (enable_irq_for_cpu(cpu, d, m)) \ - val |= (1 << bit); \ - else \ - val &= ~(1 << bit); \ -@@ -455,7 +472,7 @@ static void bcm63xx_internal_irq_mask(st - - static void bcm63xx_internal_irq_unmask(struct irq_data *d) - { -- internal_irq_unmask(d); -+ internal_irq_unmask(d, NULL); - } - - /* -@@ -503,7 +520,8 @@ static void bcm63xx_external_irq_unmask( - spin_unlock_irqrestore(&epic_lock, flags); - - if (is_ext_irq_cascaded) -- internal_irq_unmask(irq_get_irq_data(irq + ext_irq_start)); -+ internal_irq_unmask(irq_get_irq_data(irq + ext_irq_start), -+ NULL); - } - - static void bcm63xx_external_irq_clear(struct irq_data *d) -@@ -622,6 +640,18 @@ static int bcm63xx_external_irq_set_type - return IRQ_SET_MASK_OK_NOCOPY; - } - -+#ifdef CONFIG_SMP -+static int bcm63xx_internal_set_affinity(struct irq_data *data, -+ const struct cpumask *dest, -+ bool force) -+{ -+ if (!irqd_irq_disabled(data)) -+ internal_irq_unmask(data, dest); -+ -+ return 0; -+} -+#endif -+ - static struct irq_chip bcm63xx_internal_irq_chip = { - .name = "bcm63xx_ipic", - .irq_mask = bcm63xx_internal_irq_mask, -@@ -679,7 +709,10 @@ void __init arch_init_irq(void) - - setup_irq(MIPS_CPU_IRQ_BASE + 2, &cpu_ip2_cascade_action); - #ifdef CONFIG_SMP -- if (is_ext_irq_cascaded) -+ if (is_ext_irq_cascaded) { - setup_irq(MIPS_CPU_IRQ_BASE + 3, &cpu_ip3_cascade_action); -+ bcm63xx_internal_irq_chip.irq_set_affinity = -+ bcm63xx_internal_set_affinity; -+ } - #endif - } diff --git a/target/linux/brcm63xx/patches-3.9/323-cfe_simplify_detection.patch b/target/linux/brcm63xx/patches-3.9/323-cfe_simplify_detection.patch deleted file mode 100644 index e05c91d931..0000000000 --- a/target/linux/brcm63xx/patches-3.9/323-cfe_simplify_detection.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h -@@ -1,6 +1,8 @@ - #ifndef BCM63XX_BOARD_H_ - #define BCM63XX_BOARD_H_ - -+#include -+ - const char *board_get_name(void); - - void board_prom_init(void); -@@ -9,4 +11,8 @@ void board_setup(void); - - int board_register_devices(void); - -+static inline bool bcm63xx_is_cfe_present(void) { -+ return fw_arg3 == 0x43464531; -+} -+ - #endif /* ! BCM63XX_BOARD_H_ */ diff --git a/target/linux/brcm63xx/patches-3.9/324-bcm63xxpart_use_cfedetection.patch b/target/linux/brcm63xx/patches-3.9/324-bcm63xxpart_use_cfedetection.patch deleted file mode 100644 index fd7d08a3db..0000000000 --- a/target/linux/brcm63xx/patches-3.9/324-bcm63xxpart_use_cfedetection.patch +++ /dev/null @@ -1,51 +0,0 @@ ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -35,7 +35,7 @@ - - #include - #include --#include -+#include - - #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */ - -@@ -43,30 +43,6 @@ - - #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0 - --static int bcm63xx_detect_cfe(struct mtd_info *master) --{ -- char buf[9]; -- int ret; -- size_t retlen; -- -- ret = mtd_read(master, BCM963XX_CFE_VERSION_OFFSET, 5, &retlen, -- (void *)buf); -- buf[retlen] = 0; -- -- if (ret) -- return ret; -- -- if (strncmp("cfe-v", buf, 5) == 0) -- return 0; -- -- /* very old CFE's do not have the cfe-v string, so check for magic */ -- ret = mtd_read(master, BCM63XX_CFE_MAGIC_OFFSET, 8, &retlen, -- (void *)buf); -- buf[retlen] = 0; -- -- return strncmp("CFE1CFE1", buf, 8); --} -- - static int bcm63xx_parse_cfe_partitions(struct mtd_info *master, - struct mtd_partition **pparts, - struct mtd_part_parser_data *data) -@@ -85,7 +61,7 @@ static int bcm63xx_parse_cfe_partitions( - u32 computed_crc; - bool rootfs_first = false; - -- if (bcm63xx_detect_cfe(master)) -+ if (!bcm63xx_is_cfe_present()) - return -EINVAL; - - cfe_erasesize = max_t(uint32_t, master->erasesize, diff --git a/target/linux/brcm63xx/patches-3.9/400-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-3.9/400-bcm963xx_flashmap.patch deleted file mode 100644 index 1aadfff476..0000000000 --- a/target/linux/brcm63xx/patches-3.9/400-bcm963xx_flashmap.patch +++ /dev/null @@ -1,65 +0,0 @@ -From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001 -From: Axel Gembe -Date: Mon, 12 May 2008 18:54:09 +0200 -Subject: [PATCH] bcm963xx: flashmap support - -Signed-off-by: Axel Gembe ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 19 +---------------- - drivers/mtd/maps/bcm963xx-flash.c | 32 ++++++++++++++++++++++++---- - drivers/mtd/redboot.c | 13 +++++++++-- - 3 files changed, 38 insertions(+), 26 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -30,7 +30,7 @@ static struct mtd_partition mtd_partitio - } - }; - --static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL }; -+static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; - - static struct physmap_flash_data flash_data = { - .width = 2, ---- a/drivers/mtd/redboot.c -+++ b/drivers/mtd/redboot.c -@@ -72,6 +72,7 @@ static int parse_redboot_partitions(stru - int nulllen = 0; - int numslots; - unsigned long offset; -+ unsigned long fis_origin = 0; - #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED - static char nullstring[] = "unallocated"; - #endif -@@ -176,6 +177,16 @@ static int parse_redboot_partitions(stru - goto out; - } - -+ if (data && data->origin) { -+ fis_origin = data->origin; -+ } else { -+ for (i = 0; i < numslots; i++) { -+ if (!strncmp(buf[i].name, "RedBoot", 8)) { -+ fis_origin = (buf[i].flash_base & (master->size << 1) - 1); -+ } -+ } -+ } -+ - for (i = 0; i < numslots; i++) { - struct fis_list *new_fl, **prev; - -@@ -196,10 +207,10 @@ static int parse_redboot_partitions(stru - goto out; - } - new_fl->img = &buf[i]; -- if (data && data->origin) -- buf[i].flash_base -= data->origin; -- else -- buf[i].flash_base &= master->size-1; -+ if (fis_origin) -+ buf[i].flash_base -= fis_origin; -+ -+ buf[i].flash_base &= (master->size << 1) - 1; - - /* I'm sure the JFFS2 code has done me permanent damage. - * I now think the following is _normal_ diff --git a/target/linux/brcm63xx/patches-3.9/401-bcm963xx_real_rootfs_length.patch b/target/linux/brcm63xx/patches-3.9/401-bcm963xx_real_rootfs_length.patch deleted file mode 100644 index caf8b9514d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/401-bcm963xx_real_rootfs_length.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/include/uapi/linux/bcm963xx_tag.h -+++ b/include/uapi/linux/bcm963xx_tag.h -@@ -85,8 +85,10 @@ struct bcm_tag { - __u32 rootfs_crc; - /* 224-227: CRC32 of kernel partition */ - __u32 kernel_crc; -- /* 228-235: Unused at present */ -- char reserved1[8]; -+ /* 228-231: Image sequence number */ -+ char image_sequence[4]; -+ /* 222-235: Openwrt: real rootfs length */ -+ __u32 real_rootfs_length; - /* 236-239: CRC32 of header excluding last 20 bytes */ - __u32 header_crc; - /* 240-255: Unused at present */ ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -110,7 +110,8 @@ static int bcm63xx_parse_cfe_partitions( - } else { - /* OpenWrt layout */ - rootfsaddr = kerneladdr + kernellen; -- rootfslen = spareaddr - rootfsaddr; -+ rootfslen = buf->real_rootfs_length; -+ spareaddr = rootfsaddr + rootfslen; - } - } else { - pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n", diff --git a/target/linux/brcm63xx/patches-3.9/402_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-3.9/402_bcm63xx_enet_vlan_incoming_fixed.patch deleted file mode 100644 index 01779907ca..0000000000 --- a/target/linux/brcm63xx/patches-3.9/402_bcm63xx_enet_vlan_incoming_fixed.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1637,7 +1637,7 @@ static int compute_hw_mtu(struct bcm_ene - actual_mtu = mtu; - - /* add ethernet header + vlan tag size */ -- actual_mtu += VLAN_ETH_HLEN; -+ actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN; - - if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU) - return -EINVAL; diff --git a/target/linux/brcm63xx/patches-3.9/403-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-3.9/403-6358-enet1-external-mii-clk.patch deleted file mode 100644 index bc7225a6a6..0000000000 --- a/target/linux/brcm63xx/patches-3.9/403-6358-enet1-external-mii-clk.patch +++ /dev/null @@ -1,22 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -910,6 +910,8 @@ void __init board_prom_init(void) - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G3_EXT_MII | - GPIO_MODE_6348_G0_EXT_MII; -+ else if (BCMCPU_IS_6358()) -+ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV; - } - - bcm_gpio_writel(val, GPIO_MODE_REG); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -621,6 +621,8 @@ - #define GPIO_MODE_6358_EXTRA_SPI_SS (1 << 7) - #define GPIO_MODE_6358_SERIAL_LED (1 << 10) - #define GPIO_MODE_6358_UTOPIA (1 << 12) -+#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 30) -+#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 31) - - #define GPIO_MODE_6368_ANALOG_AFE_0 (1 << 0) - #define GPIO_MODE_6368_ANALOG_AFE_1 (1 << 1) diff --git a/target/linux/brcm63xx/patches-3.9/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch b/target/linux/brcm63xx/patches-3.9/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch deleted file mode 100644 index 1f331757e9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch +++ /dev/null @@ -1,169 +0,0 @@ -From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Fri, 6 Jan 2012 12:24:18 +0100 -Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove - -Only connect/disconnect the phy during probe and remove, not during any -open/close. The phy seldom changes during the runtime, and disconnecting -the phy during close will prevent it from keeping any configuration over -a down/up cycle. - -Signed-off-by: Jonas Gorski ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 84 +++++++++++++------------- - 1 files changed, 41 insertions(+), 43 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -870,10 +870,8 @@ static int bcm_enet_open(struct net_devi - struct bcm_enet_priv *priv; - struct sockaddr addr; - struct device *kdev; -- struct phy_device *phydev; - int i, ret; - unsigned int size; -- char phy_id[MII_BUS_ID_SIZE + 3]; - void *p; - u32 val; - -@@ -881,40 +879,10 @@ static int bcm_enet_open(struct net_devi - kdev = &priv->pdev->dev; - - if (priv->has_phy) { -- /* connect to PHY */ -- snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, -- priv->mii_bus->id, priv->phy_id); -- -- phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, -- PHY_INTERFACE_MODE_MII); -- -- if (IS_ERR(phydev)) { -- dev_err(kdev, "could not attach to PHY\n"); -- return PTR_ERR(phydev); -- } -- -- /* mask with MAC supported features */ -- phydev->supported &= (SUPPORTED_10baseT_Half | -- SUPPORTED_10baseT_Full | -- SUPPORTED_100baseT_Half | -- SUPPORTED_100baseT_Full | -- SUPPORTED_Autoneg | -- SUPPORTED_Pause | -- SUPPORTED_MII); -- phydev->advertising = phydev->supported; -- -- if (priv->pause_auto && priv->pause_rx && priv->pause_tx) -- phydev->advertising |= SUPPORTED_Pause; -- else -- phydev->advertising &= ~SUPPORTED_Pause; -- -- dev_info(kdev, "attached PHY at address %d [%s]\n", -- phydev->addr, phydev->drv->name); -- -+ /* Reset state */ - priv->old_link = 0; - priv->old_duplex = -1; - priv->old_pause = -1; -- priv->phydev = phydev; - } - - /* mask all interrupts and request them */ -@@ -924,7 +892,7 @@ static int bcm_enet_open(struct net_devi - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -- goto out_phy_disconnect; -+ return ret; - - ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, IRQF_DISABLED, - dev->name, dev); -@@ -1131,9 +1099,6 @@ out_freeirq_rx: - out_freeirq: - free_irq(dev->irq, dev); - --out_phy_disconnect: -- phy_disconnect(priv->phydev); -- - return ret; - } - -@@ -1238,12 +1203,6 @@ static int bcm_enet_stop(struct net_devi - free_irq(priv->irq_rx, dev); - free_irq(dev->irq, dev); - -- /* release phy */ -- if (priv->has_phy) { -- phy_disconnect(priv->phydev); -- priv->phydev = NULL; -- } -- - return 0; - } - -@@ -1838,6 +1797,8 @@ static int bcm_enet_probe(struct platfor - - /* MII bus registration */ - if (priv->has_phy) { -+ struct phy_device *phydev; -+ char phy_id[MII_BUS_ID_SIZE + 3]; - - priv->mii_bus = mdiobus_alloc(); - if (!priv->mii_bus) { -@@ -1875,6 +1836,38 @@ static int bcm_enet_probe(struct platfor - dev_err(&pdev->dev, "unable to register mdio bus\n"); - goto out_free_mdio; - } -+ -+ /* connect to PHY */ -+ snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, -+ priv->mii_bus->id, priv->phy_id); -+ -+ phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, -+ PHY_INTERFACE_MODE_MII); -+ -+ if (IS_ERR(phydev)) { -+ dev_err(&pdev->dev, "could not attach to PHY\n"); -+ goto out_unregister_mdio; -+ } -+ -+ /* mask with MAC supported features */ -+ phydev->supported &= (SUPPORTED_10baseT_Half | -+ SUPPORTED_10baseT_Full | -+ SUPPORTED_100baseT_Half | -+ SUPPORTED_100baseT_Full | -+ SUPPORTED_Autoneg | -+ SUPPORTED_Pause | -+ SUPPORTED_MII); -+ phydev->advertising = phydev->supported; -+ -+ if (priv->pause_auto && priv->pause_rx && priv->pause_tx) -+ phydev->advertising |= SUPPORTED_Pause; -+ else -+ phydev->advertising &= ~SUPPORTED_Pause; -+ -+ dev_info(&pdev->dev, "attached PHY at address %d [%s]\n", -+ phydev->addr, phydev->drv->name); -+ -+ priv->phydev = phydev; - } else { - - /* run platform code to initialize PHY device */ -@@ -1920,6 +1913,9 @@ static int bcm_enet_probe(struct platfor - return 0; - - out_unregister_mdio: -+ if (priv->phydev) -+ phy_disconnect(priv->phydev); -+ - if (priv->mii_bus) - mdiobus_unregister(priv->mii_bus); - -@@ -1961,6 +1957,8 @@ static int bcm_enet_remove(struct platfo - enet_writel(priv, 0, ENET_MIISC_REG); - - if (priv->has_phy) { -+ phy_disconnect(priv->phydev); -+ priv->phydev = NULL; - mdiobus_unregister(priv->mii_bus); - mdiobus_free(priv->mii_bus); - } else { diff --git a/target/linux/brcm63xx/patches-3.9/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch b/target/linux/brcm63xx/patches-3.9/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch deleted file mode 100644 index ea11c4140f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch +++ /dev/null @@ -1,53 +0,0 @@ -From d8237d704fc25eb2fc25ef4403608b78c6a6d4be Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 15 Jul 2012 20:08:57 +0200 -Subject: [PATCH 54/81] bcm63xx_enet: enable rgmii clock on external ports - ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 13 +++++++++++++ - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++++++++ - 2 files changed, 25 insertions(+), 0 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -931,6 +931,19 @@ - #define ENETSW_PORTOV_FDX_MASK (1 << 1) - #define ENETSW_PORTOV_LINKUP_MASK (1 << 0) - -+/* Port RGMII control register */ -+#define ENETSW_RGMII_CTRL_REG(x) (0x60 + (x)) -+#define ENETSW_RGMII_CTRL_GMII_CLK_EN (1 << 7) -+#define ENETSW_RGMII_CTRL_MII_OVERRIDE_EN (1 << 6) -+#define ENETSW_RGMII_CTRL_MII_MODE_MASK (3 << 4) -+#define ENETSW_RGMII_CTRL_RGMII_MODE (0 << 4) -+#define ENETSW_RGMII_CTRL_MII_MODE (1 << 4) -+#define ENETSW_RGMII_CTRL_RVMII_MODE (2 << 4) -+#define ENETSW_RGMII_CTRL_TIMING_SEL_EN (1 << 0) -+ -+/* Port RGMII timing register */ -+#define ENETSW_RGMII_TIMING_REG(x) (0x68 + (x)) -+ - /* MDIO control register */ - #define ENETSW_MDIOC_REG (0xb0) - #define ENETSW_MDIOC_EXT_MASK (1 << 16) ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2233,6 +2233,18 @@ static int bcm_enetsw_open(struct net_de - priv->sw_port_link[i] = 0; - } - -+ /* enable external ports */ -+ for (i = ENETSW_RGMII_PORT0; i < priv->num_ports; i++) { -+ u8 rgmii_ctrl; -+ -+ if (!priv->used_ports[i].used) -+ continue; -+ -+ rgmii_ctrl = enetsw_readb(priv, ENETSW_RGMII_CTRL_REG(i)); -+ rgmii_ctrl |= ENETSW_RGMII_CTRL_GMII_CLK_EN; -+ enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); -+ } -+ - /* reset mib */ - val = enetsw_readb(priv, ENETSW_GMCR_REG); - val |= ENETSW_GMCR_RST_MIB_MASK; diff --git a/target/linux/brcm63xx/patches-3.9/409-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch b/target/linux/brcm63xx/patches-3.9/409-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch deleted file mode 100644 index 7c0bd4860f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/409-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch +++ /dev/null @@ -1,134 +0,0 @@ -From 261ee140e75615351128eee497e6bbd76686784b Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 12 Nov 2011 12:18:26 +0100 -Subject: [PATCH 51/72] MIPS: BCM63XX: add HS SPI platform device and register - it - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/Makefile | 4 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 + - arch/mips/bcm63xx/dev-hsspi.c | 57 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 20 +++++++ - 4 files changed, 81 insertions(+), 2 deletions(-) - create mode 100644 arch/mips/bcm63xx/dev-hsspi.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,8 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ -- dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \ -- dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o -+ dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \ -+ dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ -+ usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -26,6 +26,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -1003,6 +1004,7 @@ int __init board_register_devices(void) - pr_err(PFX "failed to register fallback SPROM\n"); - } - #endif -+ bcm63xx_hsspi_register(); - - bcm63xx_spi_register(); - ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-hsspi.c -@@ -0,0 +1,60 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2012 Jonas Gorski -+ */ -+ -+#include -+#include -+#include -+ -+#include -+#include -+#include -+ -+static struct resource spi_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct bcm63xx_hsspi_pdata spi_pdata = { -+ .bus_num = 1, -+}; -+ -+static struct platform_device bcm63xx_hsspi_device = { -+ .name = "bcm63xx-hsspi", -+ .id = 0, -+ .num_resources = ARRAY_SIZE(spi_resources), -+ .resource = spi_resources, -+ .dev = { -+ .platform_data = &spi_pdata, -+ }, -+}; -+ -+int __init bcm63xx_hsspi_register(void) -+{ -+ -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362()) -+ return -ENODEV; -+ -+ spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI); -+ spi_resources[0].end = spi_resources[0].start; -+ spi_resources[0].end += RSET_HSSPI_SIZE - 1; -+ spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI); -+ -+ if (BCMCPU_IS_6328()) -+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6328; -+ else if (BCMCPU_IS_6362()) -+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6362; -+ -+ return platform_device_register(&bcm63xx_hsspi_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -@@ -0,0 +1,21 @@ -+#ifndef BCM63XX_DEV_HSSPI_H -+#define BCM63XX_DEV_HSSPI_H -+ -+#include -+#include -+#include -+ -+int __init bcm63xx_hsspi_register(void); -+ -+struct bcm63xx_hsspi_pdata { -+ int bus_num; -+ u32 speed_hz; -+}; -+ -+#define bcm_hsspi_readl(o) bcm_rset_readl(RSET_HSSPI, (o)) -+#define bcm_hsspi_writel(v, o) bcm_rset_writel(RSET_HSSPI, (v), (o)) -+ -+#define HSSPI_PLL_HZ_6328 133333333 -+#define HSSPI_PLL_HZ_6362 400000000 -+ -+#endif /* BCM63XX_DEV_HSSPI_H */ diff --git a/target/linux/brcm63xx/patches-3.9/410-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch b/target/linux/brcm63xx/patches-3.9/410-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch deleted file mode 100644 index 8f52389f1d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/410-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch +++ /dev/null @@ -1,481 +0,0 @@ -From 4b27423676485d05bcd6fc6f3809164fb8f9d22d Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sat, 12 Nov 2011 12:19:55 +0100 -Subject: [PATCH 30/60] SPI: MIPS: BCM63XX: Add HSSPI driver - -Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs. - -Signed-off-by: Jonas Gorski ---- - .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 2 + - drivers/spi/Kconfig | 7 + - drivers/spi/Makefile | 1 + - drivers/spi/spi-bcm63xx-hsspi.c | 427 ++++++++++++++++++++ - 4 files changed, 437 insertions(+), 0 deletions(-) - create mode 100644 drivers/spi/spi-bcm63xx-hsspi.c - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -@@ -18,4 +18,6 @@ struct bcm63xx_hsspi_pdata { - #define HSSPI_PLL_HZ_6328 133333333 - #define HSSPI_PLL_HZ_6362 400000000 - -+#define HSSPI_BUFFER_LEN 512 -+ - #endif /* BCM63XX_DEV_HSSPI_H */ ---- a/drivers/spi/Kconfig -+++ b/drivers/spi/Kconfig -@@ -101,6 +101,13 @@ config SPI_BCM63XX - help - Enable support for the SPI controller on the Broadcom BCM63xx SoCs. - -+config SPI_BCM63XX_HSSPI -+ tristate "Broadcom BCM63XX HS SPI controller driver" -+ depends on BCM63XX -+ help -+ This enables support for the High Speed SPI controller present on -+ newer Broadcom BCM63XX SoCs. -+ - config SPI_BITBANG - tristate "Utilities for Bitbanging SPI masters" - help ---- a/drivers/spi/Makefile -+++ b/drivers/spi/Makefile -@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o - obj-$(CONFIG_SPI_ATH79) += spi-ath79.o - obj-$(CONFIG_SPI_AU1550) += spi-au1550.o - obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o -+obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o - obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o - obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o - obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o ---- /dev/null -+++ b/drivers/spi/spi-bcm63xx-hsspi.c -@@ -0,0 +1,427 @@ -+/* -+ * Broadcom BCM63XX High Speed SPI Controller driver -+ * -+ * Copyright 2000-2010 Broadcom Corporation -+ * Copyright 2012 Jonas Gorski -+ * -+ * Licensed under the GNU/GPL. See COPYING for details. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+#include -+ -+#define HSSPI_OP_CODE_SHIFT 13 -+#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT) -+ -+#define HSSPI_MAX_PREPEND_LEN 15 -+ -+#define HSSPI_MAX_SYNC_CLOCK 30000000 -+ -+struct bcm63xx_hsspi { -+ struct completion done; -+ struct spi_transfer *curr_trans; -+ -+ struct platform_device *pdev; -+ struct clk *clk; -+ void __iomem *regs; -+ u8 __iomem *fifo; -+ -+ u32 speed_hz; -+ int irq; -+}; -+ -+static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, int hz, -+ int profile) -+{ -+ u32 reg; -+ -+ reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz)); -+ bcm_hsspi_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg, -+ HSSPI_PROFILE_CLK_CTRL_REG(profile)); -+ -+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); -+ if (hz > HSSPI_MAX_SYNC_CLOCK) -+ reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH; -+ else -+ reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH; -+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); -+} -+ -+static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, -+ struct spi_transfer *t1, -+ struct spi_transfer *t2) -+{ -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master); -+ u8 chip_select = spi->chip_select; -+ u16 opcode = 0; -+ int len, prepend_size = 0; -+ -+ init_completion(&bs->done); -+ -+ bs->curr_trans = t2 ? t2 : t1; -+ bcm63xx_hsspi_set_clk(bs, bs->curr_trans->speed_hz, chip_select); -+ -+ if (t2 && !t2->tx_buf) -+ prepend_size = t1->len; -+ -+ bcm_hsspi_writel(prepend_size << MODE_CTRL_PREPENDBYTE_CNT_SHIFT | -+ 2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT | -+ 2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff, -+ HSSPI_PROFILE_MODE_CTRL_REG(chip_select)); -+ -+ if (t1->rx_buf && t1->tx_buf) -+ opcode = HSSPI_OP_READ_WRITE; -+ else if (t1->rx_buf || (t2 && t2->rx_buf)) -+ opcode = HSSPI_OP_READ; -+ else if (t1->tx_buf) -+ opcode = HSSPI_OP_WRITE; -+ -+ if (opcode == HSSPI_OP_READ && t2) -+ len = t2->len; -+ else -+ len = t1->len; -+ -+ if (t1->tx_buf) { -+ memcpy_toio(bs->fifo + 2, t1->tx_buf, t1->len); -+ if (t2 && t2->tx_buf) { -+ memcpy_toio(bs->fifo + 2 + t1->len, -+ t2->tx_buf, t2->len); -+ len += t2->len; -+ } -+ } -+ -+ opcode |= len; -+ memcpy_toio(bs->fifo, &opcode, sizeof(opcode)); -+ -+ /* enable interrupt */ -+ bcm_hsspi_writel(HSSPI_PING0_CMD_DONE, HSSPI_INT_MASK_REG); -+ -+ /* start the transfer */ -+ bcm_hsspi_writel(chip_select << PINGPONG_CMD_SS_SHIFT | -+ chip_select << PINGPONG_CMD_PROFILE_SHIFT | -+ PINGPONG_COMMAND_START_NOW, -+ HSSPI_PINGPONG_COMMAND_REG(0)); -+ -+ if (wait_for_completion_timeout(&bs->done, HZ) == 0) { -+ dev_err(&bs->pdev->dev, "transfer timed out!\n"); -+ return -ETIMEDOUT; -+ } -+ -+ return t1->len + (t2 ? t2->len : 0); -+} -+ -+static int bcm63xx_hsspi_setup(struct spi_device *spi) -+{ -+ u32 reg; -+ -+ if (spi->bits_per_word != 8) -+ return -EINVAL; -+ -+ if (spi->max_speed_hz == 0) -+ return -EINVAL; -+ -+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); -+ reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING); -+ if (spi->mode & SPI_CPHA) -+ reg |= SIGNAL_CTRL_LAUNCH_RISING; -+ else -+ reg |= SIGNAL_CTRL_LATCH_RISING; -+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); -+ -+ return 0; -+} -+ -+static int bcm63xx_hsspi_transfer_one(struct spi_master *master, -+ struct spi_message *msg) -+{ -+ struct spi_transfer *t, *prev = NULL; -+ struct spi_device *spi = msg->spi; -+ u32 reg; -+ int ret = -EINVAL; -+ int len = 0; -+ -+ /* check if we are able to make these transfers */ -+ list_for_each_entry(t, &msg->transfers, transfer_list) { -+ if (!t->tx_buf && !t->rx_buf) -+ goto out; -+ -+ if (t->speed_hz == 0) -+ t->speed_hz = spi->max_speed_hz; -+ -+ if (t->speed_hz > spi->max_speed_hz) -+ goto out; -+ -+ if (t->len > HSSPI_BUFFER_LEN) -+ goto out; -+ -+ /* -+ * This controller does not support keeping the chip select -+ * active between transfers. -+ * This logic currently supports combining: -+ * write then read with no cs_change (e.g. m25p80 RDSR) -+ * write then write with no cs_change (e.g. m25p80 PP) -+ */ -+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) { -+ /* -+ * reject if we have to combine two tx transfers and -+ * their combined length is bigger than the buffer -+ */ -+ if (prev->tx_buf && t->tx_buf && -+ (prev->len + t->len) > HSSPI_BUFFER_LEN) -+ goto out; -+ /* -+ * reject if we need write more than 15 bytes in read -+ * then write. -+ */ -+ if (prev->tx_buf && t->rx_buf && -+ prev->len > HSSPI_MAX_PREPEND_LEN) -+ goto out; -+ } -+ -+ } -+ -+ /* setup clock polarity */ -+ reg = bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG); -+ reg &= ~GLOBAL_CTRL_CLK_POLARITY; -+ if (spi->mode & SPI_CPOL) -+ reg |= GLOBAL_CTRL_CLK_POLARITY; -+ bcm_hsspi_writel(reg, HSSPI_GLOBAL_CTRL_REG); -+ -+ list_for_each_entry(t, &msg->transfers, transfer_list) { -+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) { -+ /* combine write with following transfer */ -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, t); -+ if (ret < 0) -+ goto out; -+ -+ len += ret; -+ prev = NULL; -+ continue; -+ } -+ -+ /* write the previous pending transfer */ -+ if (prev != NULL) { -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL); -+ if (ret < 0) -+ goto out; -+ -+ len += ret; -+ } -+ -+ prev = t; -+ } -+ -+ /* do last pending transfer */ -+ if (prev != NULL) { -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL); -+ if (ret < 0) -+ goto out; -+ len += ret; -+ } -+ -+ msg->actual_length = len; -+ ret = 0; -+out: -+ msg->status = ret; -+ spi_finalize_current_message(master); -+ return 0; -+} -+ -+static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id) -+{ -+ struct spi_master *master = (struct spi_master *)dev_id; -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ if (bcm_hsspi_readl(HSSPI_INT_STATUS_MASKED_REG) == 0) -+ return IRQ_NONE; -+ -+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG); -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ -+ if (bs->curr_trans && bs->curr_trans->rx_buf) -+ memcpy_fromio(bs->curr_trans->rx_buf, bs->fifo, -+ bs->curr_trans->len); -+ complete(&bs->done); -+ -+ return IRQ_HANDLED; -+} -+ -+static int bcm63xx_hsspi_probe(struct platform_device *pdev) -+{ -+ -+ struct spi_master *master; -+ struct bcm63xx_hsspi *bs; -+ struct resource *res_mem; -+ void __iomem *regs; -+ struct device *dev = &pdev->dev; -+ struct bcm63xx_hsspi_pdata *pdata = pdev->dev.platform_data; -+ struct clk *clk; -+ int irq; -+ int ret; -+ -+ irq = platform_get_irq(pdev, 0); -+ if (irq < 0) { -+ dev_err(dev, "no irq\n"); -+ return -ENXIO; -+ } -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ regs = devm_request_and_ioremap(dev, res_mem); -+ if (!regs) { -+ dev_err(dev, "unable to ioremap regs\n"); -+ return -ENXIO; -+ } -+ -+ clk = clk_get(dev, "hsspi"); -+ -+ if (IS_ERR(clk)) { -+ ret = PTR_ERR(clk); -+ goto out_release; -+ } -+ -+ clk_prepare_enable(clk); -+ -+ master = spi_alloc_master(&pdev->dev, sizeof(*bs)); -+ if (!master) { -+ ret = -ENOMEM; -+ goto out_disable_clk; -+ } -+ -+ bs = spi_master_get_devdata(master); -+ bs->pdev = pdev; -+ bs->clk = clk; -+ bs->regs = regs; -+ -+ master->bus_num = pdata->bus_num; -+ master->num_chipselect = 8; -+ master->setup = bcm63xx_hsspi_setup; -+ master->transfer_one_message = bcm63xx_hsspi_transfer_one; -+ master->mode_bits = SPI_CPOL | SPI_CPHA; -+ -+ bs->speed_hz = pdata->speed_hz; -+ bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0)); -+ -+ platform_set_drvdata(pdev, master); -+ -+ bs->curr_trans = NULL; -+ -+ /* Initialize the hardware */ -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ -+ /* clean up any pending interrupts */ -+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG); -+ -+ bcm_hsspi_writel(bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG) | -+ GLOBAL_CTRL_CLK_GATE_SSOFF, -+ HSSPI_GLOBAL_CTRL_REG); -+ -+ ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED, -+ pdev->name, master); -+ -+ if (ret) -+ goto out_put_master; -+ -+ /* register and we are done */ -+ ret = spi_register_master(master); -+ if (ret) -+ goto out_free_irq; -+ -+ return 0; -+ -+out_free_irq: -+ devm_free_irq(dev, bs->irq, master); -+out_put_master: -+ spi_master_put(master); -+out_disable_clk: -+ clk_disable_unprepare(clk); -+ clk_put(clk); -+out_release: -+ devm_ioremap_release(dev, regs); -+ -+ return ret; -+} -+ -+ -+static int __exit bcm63xx_hsspi_remove(struct platform_device *pdev) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ spi_unregister_master(master); -+ -+ /* reset the hardware and block queue progress */ -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ clk_disable_unprepare(bs->clk); -+ clk_put(bs->clk); -+ -+ return 0; -+} -+ -+#ifdef CONFIG_PM -+static int bcm63xx_hsspi_suspend(struct platform_device *pdev, -+ pm_message_t mesg) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ spi_master_suspend(master); -+ clk_disable(bs->clk); -+ -+ return 0; -+} -+ -+static int bcm63xx_hsspi_resume(struct platform_device *pdev) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ clk_enable(bs->clk); -+ spi_master_resume(master); -+ -+ return 0; -+} -+ -+static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = { -+ .suspend = bcm63xx_hsspi_suspend, -+ .resume = bcm63xx_hsspi_resume, -+}; -+ -+#define BCM63XX_HSSPI_PM_OPS (&bcm63xx_hsspi_pm_ops) -+#else -+#define BCM63XX_HSSPI_PM_OPS NULL -+#endif -+ -+ -+ -+static struct platform_driver bcm63xx_hsspi_driver = { -+ .driver = { -+ .name = "bcm63xx-hsspi", -+ .owner = THIS_MODULE, -+ .pm = BCM63XX_HSSPI_PM_OPS, -+ }, -+ .probe = bcm63xx_hsspi_probe, -+ .remove = __exit_p(bcm63xx_hsspi_remove), -+}; -+ -+module_platform_driver(bcm63xx_hsspi_driver); -+ -+MODULE_ALIAS("platform:bcm63xx_hsspi"); -+MODULE_DESCRIPTION("Broadcom BCM63xx HS SPI Controller driver"); -+MODULE_AUTHOR("Jonas Gorski "); -+MODULE_LICENSE("GPL"); diff --git a/target/linux/brcm63xx/patches-3.9/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch b/target/linux/brcm63xx/patches-3.9/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch deleted file mode 100644 index ddeb751041..0000000000 --- a/target/linux/brcm63xx/patches-3.9/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch +++ /dev/null @@ -1,104 +0,0 @@ -From d135d94b3d1fe599d13e7198d5f502912d694c13 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Sun, 3 Jul 2011 15:00:38 +0200 -Subject: [PATCH 29/60] MIPS: BCM63XX: Register SPI flash if present - -Signed-off-by: Jonas Gorski ---- - arch/mips/bcm63xx/dev-flash.c | 33 +++++++++++++++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 + - 2 files changed, 33 insertions(+), 2 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -16,9 +16,12 @@ - #include - #include - #include -+#include -+#include - - #include - #include -+#include - #include - #include - -@@ -55,6 +58,21 @@ static struct platform_device mtd_dev = - }, - }; - -+static struct flash_platform_data bcm63xx_flash_data = { -+ .part_probe_types = bcm63xx_part_types, -+}; -+ -+static struct spi_board_info bcm63xx_spi_flash_info[] = { -+ { -+ .bus_num = 0, -+ .chip_select = 0, -+ .mode = 0, -+ .max_speed_hz = 781000, -+ .modalias = "m25p80", -+ .platform_data = &bcm63xx_flash_data, -+ }, -+}; -+ - static int __init bcm63xx_detect_flash_type(void) - { - u32 val; -@@ -62,6 +80,11 @@ static int __init bcm63xx_detect_flash_t - switch (bcm63xx_get_cpu_id()) { - case BCM6328_CPU_ID: - val = bcm_misc_readl(MISC_STRAPBUS_6328_REG); -+ if (val & STRAPBUS_6328_HSSPI_CLK_FAST) -+ bcm63xx_spi_flash_info[0].max_speed_hz = 33333334; -+ else -+ bcm63xx_spi_flash_info[0].max_speed_hz = 16666667; -+ - if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) - return BCM63XX_FLASH_TYPE_SERIAL; - else -@@ -86,6 +109,9 @@ static int __init bcm63xx_detect_flash_t - return BCM63XX_FLASH_TYPE_NAND; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); -+ if (val & STRAPBUS_6368_SPI_CLK_FAST) -+ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; -+ - switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { - case STRAPBUS_6368_BOOT_SEL_NAND: - return BCM63XX_FLASH_TYPE_NAND; -@@ -117,8 +143,13 @@ int __init bcm63xx_flash_register(void) - - return platform_device_register(&mtd_dev); - case BCM63XX_FLASH_TYPE_SERIAL: -- pr_warn("unsupported serial flash detected\n"); -- return -ENODEV; -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { -+ bcm63xx_spi_flash_info[0].bus_num = 1; -+ bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN; -+ } -+ -+ return spi_register_board_info(bcm63xx_spi_flash_info, -+ ARRAY_SIZE(bcm63xx_spi_flash_info)); - case BCM63XX_FLASH_TYPE_NAND: - pr_warn("unsupported NAND flash detected\n"); - return -ENODEV; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -672,6 +672,7 @@ - #define GPIO_STRAPBUS_REG 0x40 - #define STRAPBUS_6358_BOOT_SEL_PARALLEL (1 << 1) - #define STRAPBUS_6358_BOOT_SEL_SERIAL (0 << 1) -+#define STRAPBUS_6368_SPI_CLK_FAST (1 << 6) - #define STRAPBUS_6368_BOOT_SEL_MASK 0x3 - #define STRAPBUS_6368_BOOT_SEL_NAND 0 - #define STRAPBUS_6368_BOOT_SEL_SERIAL 1 -@@ -1513,6 +1514,7 @@ - #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) - - #define MISC_STRAPBUS_6328_REG 0x240 -+#define STRAPBUS_6328_HSSPI_CLK_FAST (1 << 4) - #define STRAPBUS_6328_FCVO_SHIFT 7 - #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) - #define STRAPBUS_6328_BOOT_SEL_SERIAL (1 << 28) diff --git a/target/linux/brcm63xx/patches-3.9/412-MTD-physmap-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.9/412-MTD-physmap-allow-passing-pp_data.patch deleted file mode 100644 index de2216ab92..0000000000 --- a/target/linux/brcm63xx/patches-3.9/412-MTD-physmap-allow-passing-pp_data.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 266c506f4b262bd6aba0776a03d82c98e65d9906 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 1 May 2012 17:32:36 +0200 -Subject: [PATCH 63/79] MTD: physmap: allow passing pp_data - ---- - drivers/mtd/maps/physmap.c | 4 +++- - include/linux/mtd/physmap.h | 1 + - 2 files changed, 4 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/maps/physmap.c -+++ b/drivers/mtd/maps/physmap.c -@@ -100,6 +100,7 @@ static int physmap_flash_probe(struct pl - { - struct physmap_flash_data *physmap_data; - struct physmap_flash_info *info; -+ struct mtd_part_parser_data *pp_data; - const char **probe_type; - const char **part_types; - int err = 0; -@@ -191,8 +192,9 @@ static int physmap_flash_probe(struct pl - spin_lock_init(&info->vpp_lock); - - part_types = physmap_data->part_probe_types ? : part_probe_types; -+ pp_data = physmap_data->pp_data ? physmap_data->pp_data : NULL; - -- mtd_device_parse_register(info->cmtd, part_types, NULL, -+ mtd_device_parse_register(info->cmtd, part_types, pp_data, - physmap_data->parts, physmap_data->nr_parts); - return 0; - ---- a/include/linux/mtd/physmap.h -+++ b/include/linux/mtd/physmap.h -@@ -32,6 +32,7 @@ struct physmap_flash_data { - char *probe_type; - struct mtd_partition *parts; - const char **part_probe_types; -+ struct mtd_part_parser_data *pp_data; - }; - - #endif /* __LINUX_MTD_PHYSMAP__ */ diff --git a/target/linux/brcm63xx/patches-3.9/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch b/target/linux/brcm63xx/patches-3.9/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch deleted file mode 100644 index 34c2ef928e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 8879e209111192c5e9752d7bd203cf7582693328 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 3 May 2012 14:40:03 +0200 -Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 9 ++++++++- - arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 10 ++++++++++ - 2 files changed, 18 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -33,6 +33,7 @@ - #include - #include - #include -+#include - - #include - #include -@@ -958,6 +959,7 @@ int __init board_register_devices(void) - { - int button_count = 0; - int led_count = 0; -+ int i; - - if (board.has_uart0) - bcm63xx_uart_register(0); -@@ -996,7 +998,8 @@ int __init board_register_devices(void) - * do this after registering enet devices - */ - #ifdef CONFIG_SSB_PCIHOST -- if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { -+ if (!board.has_caldata && -+ !bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { - memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); - memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); - if (ssb_arch_register_fallback_sprom( -@@ -1042,5 +1045,9 @@ int __init board_register_devices(void) - platform_device_register(&bcm63xx_gpio_keys_device); - } - -+ /* register any fixups */ -+ for (i = 0; i < board.has_caldata; i++) -+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); -+ - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -8,6 +8,7 @@ - #include - #include - #include -+#include - - /* - * flash mapping -@@ -15,6 +16,11 @@ - #define BCM963XX_CFE_VERSION_OFFSET 0x570 - #define BCM963XX_NVRAM_OFFSET 0x580 - -+struct ath9k_caldata { -+ unsigned int slot; -+ u32 caldata_offset; -+}; -+ - /* - * board definition - */ -@@ -34,6 +40,10 @@ struct board_info { - unsigned int has_dsp:1; - unsigned int has_uart0:1; - unsigned int has_uart1:1; -+ unsigned int has_caldata:2; -+ -+ /* wifi calibration data config */ -+ struct ath9k_caldata caldata[2]; - - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; diff --git a/target/linux/brcm63xx/patches-3.9/414-MTD-m25p80-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.9/414-MTD-m25p80-allow-passing-pp_data.patch deleted file mode 100644 index 6818a4d9cc..0000000000 --- a/target/linux/brcm63xx/patches-3.9/414-MTD-m25p80-allow-passing-pp_data.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 7f17dfe9009beb07a3de0e380932a725293829df Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 1 May 2012 17:33:03 +0200 -Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data - ---- - drivers/mtd/devices/m25p80.c | 3 +++ - include/linux/spi/flash.h | 2 ++ - 2 files changed, 5 insertions(+) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -972,6 +972,9 @@ static int m25p_probe(struct spi_device - dev_warn(&spi->dev, "unrecognized id %s\n", data->type); - } - -+ if (data && data->pp_data) -+ memcpy(&ppdata, data->pp_data, sizeof(ppdata)); -+ - info = (void *)id->driver_data; - - if (info->jedec_id) { ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -12,6 +12,7 @@ struct mtd_part_parser_data; - * with chips that can't be queried for JEDEC or other IDs - * @part_probe_types: optional list of MTD parser names to use for - * partitioning -+ * @pp_data: optional partition parser data. - * - * @max_transfer_len: option maximum read/write length limitation for - * SPI controllers not able to transfer any length commands. -@@ -30,6 +31,7 @@ struct flash_platform_data { - char *type; - - const char **part_probe_types; -+ struct mtd_part_parser_data *pp_data; - - unsigned int max_transfer_len; - /* we'll likely add more ... use JEDEC IDs, etc */ diff --git a/target/linux/brcm63xx/patches-3.9/415-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch b/target/linux/brcm63xx/patches-3.9/415-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch deleted file mode 100644 index 2d2533bddb..0000000000 --- a/target/linux/brcm63xx/patches-3.9/415-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch +++ /dev/null @@ -1,119 +0,0 @@ -From f888824d352df894ab721a5ca067b0313500efe7 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 3 May 2012 12:17:54 +0200 -Subject: [PATCH 38/59] MIPS: BCM63XX: store the flash type in global variable - ---- - arch/mips/bcm63xx/dev-flash.c | 36 +++++++++++++------ - .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 + - 2 files changed, 26 insertions(+), 12 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -25,6 +25,8 @@ - #include - #include - -+int bcm63xx_attached_flash = -1; -+ - static struct mtd_partition mtd_partitions[] = { - { - .name = "cfe", -@@ -86,27 +88,31 @@ static int __init bcm63xx_detect_flash_t - bcm63xx_spi_flash_info[0].max_speed_hz = 16666667; - - if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; - else -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: - case BCM6348_CPU_ID: - /* no way to auto detect so assume parallel */ -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; -+ break; - case BCM3368_CPU_ID: - case BCM6358_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL) -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; - else -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; -+ break; - case BCM6362_CPU_ID: - val = bcm_misc_readl(MISC_STRAPBUS_6362_REG); - if (val & STRAPBUS_6362_BOOT_SEL_SERIAL) -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; - else -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6368_SPI_CLK_FAST) -@@ -114,25 +120,32 @@ static int __init bcm63xx_detect_flash_t - - switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { - case STRAPBUS_6368_BOOT_SEL_NAND: -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case STRAPBUS_6368_BOOT_SEL_SERIAL: -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; -+ break; - case STRAPBUS_6368_BOOT_SEL_PARALLEL: -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; -+ break; -+ default: -+ return -EINVAL; - } - default: - return -EINVAL; - } -+ -+ return 0; - } - - int __init bcm63xx_flash_register(void) - { -- int flash_type; - u32 val; - -- flash_type = bcm63xx_detect_flash_type(); - -- switch (flash_type) { -+ bcm63xx_detect_flash_type(); -+ -+ switch (bcm63xx_attached_flash) { - case BCM63XX_FLASH_TYPE_PARALLEL: - /* read base address of boot chip select (0) */ - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); -@@ -155,7 +168,7 @@ int __init bcm63xx_flash_register(void) - return -ENODEV; - default: - pr_err("flash detection failed for BCM%x: %d\n", -- bcm63xx_get_cpu_id(), flash_type); -+ bcm63xx_get_cpu_id(), bcm63xx_attached_flash); - return -ENODEV; - } - } ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -7,6 +7,8 @@ enum { - BCM63XX_FLASH_TYPE_NAND, - }; - -+extern int bcm63xx_attached_flash; -+ - int __init bcm63xx_flash_register(void); - - #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.9/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch b/target/linux/brcm63xx/patches-3.9/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch deleted file mode 100644 index 8e2feb8bf6..0000000000 --- a/target/linux/brcm63xx/patches-3.9/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch +++ /dev/null @@ -1,227 +0,0 @@ -From bbebbf735a02b6d044ed928978ab4bd5f1833364 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 3 May 2012 14:36:11 +0200 -Subject: [PATCH 61/72] BCM63XX: add a fixup for ath9k devices - ---- - arch/mips/bcm63xx/Makefile | 3 +- - arch/mips/bcm63xx/pci-ath9k-fixup.c | 190 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/pci_ath9k_fixup.h | 7 + - 3 files changed, 199 insertions(+), 1 deletion(-) - create mode 100644 arch/mips/bcm63xx/pci-ath9k-fixup.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ - dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \ - dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ -- usb-common.o -+ pci-ath9k-fixup.o usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -0,0 +1,190 @@ -+/* -+ * Broadcom BCM63XX Ath9k EEPROM fixup helper. -+ * -+ * Copytight (C) 2012 Jonas Gorski -+ * -+ * Based on -+ * -+ * Atheros AP94 reference board PCI initialization -+ * -+ * Copyright (C) 2009-2010 Gabor Juhos -+ * -+ * This program is free software; you can redistribute it and/or modify it -+ * under the terms of the GNU General Public License version 2 as published -+ * by the Free Software Foundation. -+ */ -+ -+#include -+#include -+#include -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+struct ath9k_fixup { -+ unsigned slot; -+ u8 mac[ETH_ALEN]; -+ struct ath9k_platform_data pdata; -+}; -+ -+static int ath9k_num_fixups; -+static struct ath9k_fixup ath9k_fixups[2] = { -+ { -+ .slot = 255, -+ .pdata = { -+ .led_pin = -1, -+ }, -+ }, -+ { -+ .slot = 255, -+ .pdata = { -+ .led_pin = -1, -+ }, -+ }, -+}; -+ -+static u16 *bcm63xx_read_eeprom(u16 *eeprom, u32 offset) -+{ -+ u32 addr; -+ -+ if (BCMCPU_IS_6328()) { -+ addr = 0x18000000; -+ } else { -+ addr = bcm_mpi_readl(MPI_CSBASE_REG(0)); -+ addr &= MPI_CSBASE_BASE_MASK; -+ } -+ -+ switch (bcm63xx_attached_flash) { -+ case BCM63XX_FLASH_TYPE_PARALLEL: -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ return eeprom; -+ case BCM63XX_FLASH_TYPE_SERIAL: -+ /* the first megabyte is memory mapped */ -+ if (offset < 0x100000) { -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ return eeprom; -+ } -+ -+ if (BCMCPU_IS_6328()) { -+ /* we can change the memory mapped megabyte */ -+ bcm_hsspi_writel(offset & 0xf00000, 0x18); -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + (offset & 0xfffff)), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ bcm_hsspi_writel(0, 0x18); -+ return eeprom; -+ } -+ /* can't do anything here without talking to the SPI controller. */ -+ case BCM63XX_FLASH_TYPE_NAND: -+ default: -+ return NULL; -+ } -+} -+ -+static void ath9k_pci_fixup(struct pci_dev *dev) -+{ -+ void __iomem *mem; -+ struct ath9k_platform_data *pdata = NULL; -+ u16 *cal_data = NULL; -+ u16 cmd; -+ u32 bar0; -+ u32 val; -+ unsigned i; -+ -+ for (i = 0; i < ath9k_num_fixups; i++) { -+ if (ath9k_fixups[i].slot != PCI_SLOT(dev->devfn)) -+ continue; -+ -+ cal_data = ath9k_fixups[i].pdata.eeprom_data; -+ pdata = &ath9k_fixups[i].pdata; -+ break; -+ } -+ -+ if (cal_data == NULL) -+ return; -+ -+ if (*cal_data != 0xa55a) { -+ pr_err("pci %s: invalid calibration data\n", pci_name(dev)); -+ return; -+ } -+ -+ pr_info("pci %s: fixup device configuration\n", pci_name(dev)); -+ -+ switch (bcm63xx_get_cpu_id()) { -+ case BCM6328_CPU_ID: -+ val = BCM_PCIE_MEM_BASE_PA; -+ break; -+ case BCM6348_CPU_ID: -+ case BCM6358_CPU_ID: -+ case BCM6368_CPU_ID: -+ val = BCM_PCI_MEM_BASE_PA; -+ break; -+ default: -+ BUG(); -+ } -+ -+ mem = ioremap(val, 0x10000); -+ if (!mem) { -+ pr_err("pci %s: ioremap error\n", pci_name(dev)); -+ return; -+ } -+ -+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); -+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); -+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, val); -+ -+ pci_read_config_word(dev, PCI_COMMAND, &cmd); -+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; -+ pci_write_config_word(dev, PCI_COMMAND, cmd); -+ -+ /* set offset to first reg address */ -+ cal_data += 3; -+ while(*cal_data != 0xffff) { -+ u32 reg; -+ reg = *cal_data++; -+ val = *cal_data++; -+ val |= (*cal_data++) << 16; -+ -+ writel(val, mem + reg); -+ udelay(100); -+ } -+ -+ pci_read_config_dword(dev, PCI_VENDOR_ID, &val); -+ dev->vendor = val & 0xffff; -+ dev->device = (val >> 16) & 0xffff; -+ -+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &val); -+ dev->revision = val & 0xff; -+ dev->class = val >> 8; /* upper 3 bytes */ -+ -+ pci_read_config_word(dev, PCI_COMMAND, &cmd); -+ cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); -+ pci_write_config_word(dev, PCI_COMMAND, cmd); -+ -+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0); -+ -+ iounmap(mem); -+ -+ dev->dev.platform_data = pdata; -+} -+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); -+ -+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) -+{ -+ if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) -+ return; -+ -+ ath9k_fixups[ath9k_num_fixups].slot = slot; -+ -+ if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) -+ return; -+ -+ if (bcm63xx_nvram_get_mac_address(ath9k_fixups[ath9k_num_fixups].mac)) -+ return; -+ -+ ath9k_fixups[ath9k_num_fixups].pdata.macaddr = ath9k_fixups[ath9k_num_fixups].mac; -+ ath9k_num_fixups++; -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -0,0 +1,7 @@ -+#ifndef _PCI_ATH9K_FIXUP -+#define _PCI_ATH9K_FIXUP -+ -+ -+void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; -+ -+#endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.9/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch b/target/linux/brcm63xx/patches-3.9/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch deleted file mode 100644 index 5ce822339f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch +++ /dev/null @@ -1,120 +0,0 @@ -Allow bcm63xxpart to receive a caldata offset if calibration data is -contained in flash. ---- - drivers/mtd/bcm63xxpart.c | 51 ++++++++++++++++++++++++++++++++++++--- - include/linux/mtd/partitions.h | 2 + - 2 files changed, 49 insertions(+), 4 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -53,10 +53,12 @@ static int bcm63xx_parse_cfe_partitions( - struct mtd_partition *parts; - int ret; - size_t retlen; -- unsigned int rootfsaddr, kerneladdr, spareaddr; -+ unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr; - unsigned int rootfslen, kernellen, sparelen, totallen; - unsigned int cfelen, nvramlen; - unsigned int cfe_erasesize; -+ unsigned int caldatalen1 = 0, caldataaddr1 = 0; -+ unsigned int caldatalen2 = 0, caldataaddr2 = 0; - int i; - u32 computed_crc; - bool rootfs_first = false; -@@ -70,6 +72,24 @@ static int bcm63xx_parse_cfe_partitions( - cfelen = cfe_erasesize; - nvramlen = bcm63xx_nvram_get_psi_size(); - nvramlen = roundup(nvramlen, cfe_erasesize); -+ nvramaddr = master->size - nvramlen; -+ -+ if (data) { -+ if (data->caldata[0]) { -+ caldatalen1 = cfe_erasesize; -+ caldataaddr1 = rounddown(data->caldata[0], -+ cfe_erasesize); -+ } -+ if (data->caldata[1]) { -+ caldatalen2 = cfe_erasesize; -+ caldataaddr2 = rounddown(data->caldata[1], -+ cfe_erasesize); -+ } -+ if (caldataaddr1 == caldataaddr2) { -+ caldataaddr2 = 0; -+ caldatalen2 = 0; -+ } -+ } - - /* Allocate memory for buffer */ - buf = vmalloc(sizeof(struct bcm_tag)); -@@ -121,7 +141,7 @@ static int bcm63xx_parse_cfe_partitions( - rootfsaddr = 0; - spareaddr = cfelen; - } -- sparelen = master->size - spareaddr - nvramlen; -+ sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr; - - /* Determine number of partitions */ - if (rootfslen > 0) -@@ -130,6 +150,12 @@ static int bcm63xx_parse_cfe_partitions( - if (kernellen > 0) - nrparts++; - -+ if (caldatalen1 > 0) -+ nrparts++; -+ -+ if (caldatalen2 > 0) -+ nrparts++; -+ - /* Ask kernel for more memory */ - parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL); - if (!parts) { -@@ -167,15 +193,32 @@ static int bcm63xx_parse_cfe_partitions( - curpart++; - } - -+ if (caldatalen1 > 0) { -+ if (caldatalen2 > 0) -+ parts[curpart].name = "cal_data1"; -+ else -+ parts[curpart].name = "cal_data"; -+ parts[curpart].offset = caldataaddr1; -+ parts[curpart].size = caldatalen1; -+ curpart++; -+ } -+ -+ if (caldatalen2 > 0) { -+ parts[curpart].name = "cal_data2"; -+ parts[curpart].offset = caldataaddr2; -+ parts[curpart].size = caldatalen2; -+ curpart++; -+ } -+ - parts[curpart].name = "nvram"; -- parts[curpart].offset = master->size - nvramlen; -+ parts[curpart].offset = nvramaddr; - parts[curpart].size = nvramlen; - curpart++; - - /* Global partition "linux" to make easy firmware upgrade */ - parts[curpart].name = "linux"; - parts[curpart].offset = cfelen; -- parts[curpart].size = master->size - cfelen - nvramlen; -+ parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen; - - for (i = 0; i < nrparts; i++) - pr_info("Partition %d is %s offset %llx and length %llx\n", i, ---- a/include/linux/mtd/partitions.h -+++ b/include/linux/mtd/partitions.h -@@ -58,10 +58,12 @@ struct device_node; - /** - * struct mtd_part_parser_data - used to pass data to MTD partition parsers. - * @origin: for RedBoot, start address of MTD device -+ * @caldata: for CFE, start address of wifi calibration data - * @of_node: for OF parsers, device node containing partitioning information - */ - struct mtd_part_parser_data { - unsigned long origin; -+ unsigned long caldata[2]; - struct device_node *of_node; - }; - diff --git a/target/linux/brcm63xx/patches-3.9/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch b/target/linux/brcm63xx/patches-3.9/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch deleted file mode 100644 index ac37b42cf9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 977f8a30103b9c4992cab8f49357fe0d4274004f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Thu, 3 May 2012 14:55:26 +0200 -Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- - arch/mips/bcm63xx/dev-flash.c | 9 ++++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 4 +++- - 3 files changed, 12 insertions(+), 3 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1017,7 +1017,7 @@ int __init board_register_devices(void) - if (board.num_spis) - spi_register_board_info(board.spis, board.num_spis); - -- bcm63xx_flash_register(); -+ bcm63xx_flash_register(board.has_caldata, board.caldata); - - /* count number of LEDs defined by this device */ - while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -35,12 +35,15 @@ static struct mtd_partition mtd_partitio - } - }; - -+static struct mtd_part_parser_data bcm63xx_parser_data; -+ - static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; - - static struct physmap_flash_data flash_data = { - .width = 2, - .parts = mtd_partitions, - .part_probe_types = bcm63xx_part_types, -+ .pp_data = &bcm63xx_parser_data, - }; - - static struct resource mtd_resources[] = { -@@ -62,6 +65,7 @@ static struct platform_device mtd_dev = - - static struct flash_platform_data bcm63xx_flash_data = { - .part_probe_types = bcm63xx_part_types, -+ .pp_data = &bcm63xx_parser_data, - }; - - static struct spi_board_info bcm63xx_spi_flash_info[] = { -@@ -138,10 +142,13 @@ static int __init bcm63xx_detect_flash_t - return 0; - } - --int __init bcm63xx_flash_register(void) -+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) - { - u32 val; -+ unsigned int i; - -+ for (i = 0; i < num_caldata; i++) -+ bcm63xx_parser_data.caldata[i] = caldata[i].caldata_offset; - - bcm63xx_detect_flash_type(); - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -1,6 +1,8 @@ - #ifndef __BCM63XX_FLASH_H - #define __BCM63XX_FLASH_H - -+#include -+ - enum { - BCM63XX_FLASH_TYPE_PARALLEL, - BCM63XX_FLASH_TYPE_SERIAL, -@@ -9,6 +11,6 @@ enum { - - extern int bcm63xx_attached_flash; - --int __init bcm63xx_flash_register(void); -+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); - - #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.9/420-BCM63XX-add-endian-check-for-ath9k.patch b/target/linux/brcm63xx/patches-3.9/420-BCM63XX-add-endian-check-for-ath9k.patch deleted file mode 100644 index 9016d14827..0000000000 --- a/target/linux/brcm63xx/patches-3.9/420-BCM63XX-add-endian-check-for-ath9k.patch +++ /dev/null @@ -1,51 +0,0 @@ ---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -2,6 +2,7 @@ - #define _PCI_ATH9K_FIXUP - - --void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; -+void pci_enable_ath9k_fixup(unsigned slot, u32 offset, -+ unsigned endian_check) __init; - - #endif /* _PCI_ATH9K_FIXUP */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -19,6 +19,7 @@ - struct ath9k_caldata { - unsigned int slot; - u32 caldata_offset; -+ unsigned int endian_check:1; - }; - - /* ---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -172,12 +172,14 @@ static void ath9k_pci_fixup(struct pci_d - } - DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); - --void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) -+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, -+ unsigned endian_check) - { - if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) - return; - - ath9k_fixups[ath9k_num_fixups].slot = slot; -+ ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; - - if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) - return; ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1047,7 +1047,8 @@ int __init board_register_devices(void) - - /* register any fixups */ - for (i = 0; i < board.has_caldata; i++) -- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); -+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -+ board.caldata[i].endian_check); - - return 0; - } diff --git a/target/linux/brcm63xx/patches-3.9/421-BCM63XX-add-led-pin-for-ath9k.patch b/target/linux/brcm63xx/patches-3.9/421-BCM63XX-add-led-pin-for-ath9k.patch deleted file mode 100644 index 6ef9d0f0d9..0000000000 --- a/target/linux/brcm63xx/patches-3.9/421-BCM63XX-add-led-pin-for-ath9k.patch +++ /dev/null @@ -1,49 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1048,7 +1048,7 @@ int __init board_register_devices(void) - /* register any fixups */ - for (i = 0; i < board.has_caldata; i++) - pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -- board.caldata[i].endian_check); -+ board.caldata[i].endian_check, board.caldata[i].led_pin); - - return 0; - } ---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -173,13 +173,14 @@ static void ath9k_pci_fixup(struct pci_d - DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); - - void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, -- unsigned endian_check) -+ unsigned endian_check, int led_pin) - { - if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) - return; - - ath9k_fixups[ath9k_num_fixups].slot = slot; - ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; -+ ath9k_fixups[ath9k_num_fixups].pdata.led_pin = led_pin; - - if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) - return; ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -20,6 +20,7 @@ struct ath9k_caldata { - unsigned int slot; - u32 caldata_offset; - unsigned int endian_check:1; -+ int led_pin; - }; - - /* ---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -3,6 +3,6 @@ - - - void pci_enable_ath9k_fixup(unsigned slot, u32 offset, -- unsigned endian_check) __init; -+ unsigned endian_check, int led_pin) __init; - - #endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.9/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch b/target/linux/brcm63xx/patches-3.9/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch deleted file mode 100644 index 1d1bff57ec..0000000000 --- a/target/linux/brcm63xx/patches-3.9/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch +++ /dev/null @@ -1,205 +0,0 @@ -From 5ed5b5e9614fa5b02da699ab565af76c7e63d64d Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 7 Jan 2013 17:45:39 +0100 -Subject: [PATCH 72/72] 446-BCM63XX-add-a-fixup-for-rt2x00-devices - ---- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 17 ++++- - arch/mips/bcm63xx/dev-flash.c | 2 +- - arch/mips/bcm63xx/pci-rt2x00-fixup.c | 71 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 +- - .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 9 ++- - .../include/asm/mach-bcm63xx/pci_rt2x00_fixup.h | 9 +++ - 7 files changed, 104 insertions(+), 8 deletions(-) - create mode 100644 arch/mips/bcm63xx/pci-rt2x00-fixup.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o - setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ - dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \ - dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ -- pci-ath9k-fixup.o usb-common.o -+ pci-ath9k-fixup.o pci-rt2x00-fixup.o usb-common.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -34,6 +34,7 @@ - #include - #include - #include -+#include - - #include - #include -@@ -1046,9 +1047,19 @@ int __init board_register_devices(void) - } - - /* register any fixups */ -- for (i = 0; i < board.has_caldata; i++) -- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -- board.caldata[i].endian_check, board.caldata[i].led_pin); -+ for (i = 0; i < board.has_caldata; i++) { -+ switch (board.caldata[i].vendor) { -+ case PCI_VENDOR_ID_ATHEROS: -+ pci_enable_ath9k_fixup(board.caldata[i].slot, -+ board.caldata[i].caldata_offset, board.caldata[i].endian_check, -+ board.caldata[i].led_pin); -+ break; -+ case PCI_VENDOR_ID_RALINK: -+ pci_enable_rt2x00_fixup(board.caldata[i].slot, -+ board.caldata[i].eeprom); -+ break; -+ } -+ } - - return 0; - } ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -142,7 +142,7 @@ static int __init bcm63xx_detect_flash_t - return 0; - } - --int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) -+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata) - { - u32 val; - unsigned int i; ---- /dev/null -+++ b/arch/mips/bcm63xx/pci-rt2x00-fixup.c -@@ -0,0 +1,72 @@ -+/* -+ * Broadcom BCM63XX RT2x00 EEPROM fixup helper. -+ * -+ * Copyright (C) 2012 Álvaro Fernández Rojas -+ * -+ * Based on -+ * -+ * Broadcom BCM63XX Ath9k EEPROM fixup helper. -+ * -+ * Copyright (C) 2012 Jonas Gorski -+ * -+ * This program is free software; you can redistribute it and/or modify it -+ * under the terms of the GNU General Public License version 2 as published -+ * by the Free Software Foundation. -+ */ -+ -+#include -+#include -+#include -+#include -+ -+#include -+#include -+ -+struct rt2x00_fixup { -+ unsigned slot; -+ u8 mac[ETH_ALEN]; -+ struct rt2x00_platform_data pdata; -+}; -+ -+static int rt2x00_num_fixups; -+static struct rt2x00_fixup rt2x00_fixups[2] = { -+ { -+ .slot = 255, -+ }, -+ { -+ .slot = 255, -+ }, -+}; -+ -+static void rt2x00_pci_fixup(struct pci_dev *dev) -+{ -+ unsigned i; -+ struct rt2x00_platform_data *pdata = NULL; -+ -+ for (i = 0; i < rt2x00_num_fixups; i++) { -+ if (rt2x00_fixups[i].slot != PCI_SLOT(dev->devfn)) -+ continue; -+ -+ pdata = &rt2x00_fixups[i].pdata; -+ break; -+ } -+ -+ dev->dev.platform_data = pdata; -+} -+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_RALINK, PCI_ANY_ID, rt2x00_pci_fixup); -+ -+void __init pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) -+{ -+ if (rt2x00_num_fixups >= ARRAY_SIZE(rt2x00_fixups)) -+ return; -+ -+ rt2x00_fixups[rt2x00_num_fixups].slot = slot; -+ rt2x00_fixups[rt2x00_num_fixups].pdata.eeprom_file_name = kstrdup(eeprom, GFP_KERNEL); -+ -+ if (bcm63xx_nvram_get_mac_address(rt2x00_fixups[rt2x00_num_fixups].mac)) -+ return; -+ -+ rt2x00_fixups[rt2x00_num_fixups].pdata.mac_address = rt2x00_fixups[rt2x00_num_fixups].mac; -+ rt2x00_num_fixups++; -+} -+ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -11,6 +11,6 @@ enum { - - extern int bcm63xx_attached_flash; - --int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); -+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata); - - #endif /* __BCM63XX_FLASH_H */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -9,6 +9,7 @@ - #include - #include - #include -+#include - - /* - * flash mapping -@@ -16,11 +17,15 @@ - #define BCM963XX_CFE_VERSION_OFFSET 0x570 - #define BCM963XX_NVRAM_OFFSET 0x580 - --struct ath9k_caldata { -+struct bcm63xx_caldata { -+ unsigned int vendor; - unsigned int slot; - u32 caldata_offset; -+ /* Atheros */ - unsigned int endian_check:1; - int led_pin; -+ /* Ralink */ -+ char* eeprom; - }; - - /* -@@ -45,7 +50,7 @@ struct board_info { - unsigned int has_caldata:2; - - /* wifi calibration data config */ -- struct ath9k_caldata caldata[2]; -+ struct bcm63xx_caldata caldata[2]; - - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h -@@ -0,0 +1,9 @@ -+#ifndef _PCI_RT2X00_FIXUP -+#define _PCI_RT2X00_FIXUP -+ -+#define PCI_VENDOR_ID_RALINK 0x1814 -+ -+void pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) __init; -+ -+#endif /* _PCI_RT2X00_FIXUP */ -+ diff --git a/target/linux/brcm63xx/patches-3.9/423-bcm63xx_enet_add_b53_support.patch b/target/linux/brcm63xx/patches-3.9/423-bcm63xx_enet_add_b53_support.patch deleted file mode 100644 index 5f3eafd536..0000000000 --- a/target/linux/brcm63xx/patches-3.9/423-bcm63xx_enet_add_b53_support.patch +++ /dev/null @@ -1,169 +0,0 @@ ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -336,6 +336,9 @@ struct bcm_enet_priv { - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; - int sw_port_link[ENETSW_MAX_PORT]; - -+ /* platform device for associated switch */ -+ struct platform_device *b53_device; -+ - /* used to poll switch port state */ - struct timer_list swphy_poll; - spinlock_t enetsw_mdio_lock; ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -30,6 +30,7 @@ - #include - #include - #include -+#include - - #include - #include "bcm63xx_enet.h" -@@ -1983,7 +1984,8 @@ static int bcm_enet_remove(struct platfo - return 0; - } - --struct platform_driver bcm63xx_enet_driver = { -+ -+static struct platform_driver bcm63xx_enet_driver = { - .probe = bcm_enet_probe, - .remove = bcm_enet_remove, - .driver = { -@@ -1992,6 +1994,42 @@ struct platform_driver bcm63xx_enet_driv - }, - }; - -+struct b53_platform_data bcm63xx_b53_pdata = { -+ .chip_id = 0x6300, -+ .big_endian = 1, -+}; -+ -+struct platform_device bcm63xx_b53_dev = { -+ .name = "b53-switch", -+ .id = -1, -+ .dev = { -+ .platform_data = &bcm63xx_b53_pdata, -+ }, -+}; -+ -+static int bcmenet_switch_register(struct bcm_enet_priv *priv, u16 port_mask) -+{ -+ int ret; -+ -+ bcm63xx_b53_pdata.regs = priv->base; -+ bcm63xx_b53_pdata.enabled_ports = port_mask; -+ bcm63xx_b53_pdata.alias = priv->net_dev->name; -+ -+ ret = platform_device_register(&bcm63xx_b53_dev); -+ if (!ret) -+ priv->b53_device = &bcm63xx_b53_dev; -+ -+ return ret; -+} -+ -+static void bcmenet_switch_unregister(struct bcm_enet_priv *priv) -+{ -+ if (priv->b53_device) -+ platform_device_unregister(&bcm63xx_b53_dev); -+ -+ priv->b53_device = NULL; -+} -+ - /* - * switch mii access callbacks - */ -@@ -2245,29 +2283,6 @@ static int bcm_enetsw_open(struct net_de - enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); - } - -- /* reset mib */ -- val = enetsw_readb(priv, ENETSW_GMCR_REG); -- val |= ENETSW_GMCR_RST_MIB_MASK; -- enetsw_writeb(priv, val, ENETSW_GMCR_REG); -- mdelay(1); -- val &= ~ENETSW_GMCR_RST_MIB_MASK; -- enetsw_writeb(priv, val, ENETSW_GMCR_REG); -- mdelay(1); -- -- /* force CPU port state */ -- val = enetsw_readb(priv, ENETSW_IMPOV_REG); -- val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -- enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -- -- /* enable switch forward engine */ -- val = enetsw_readb(priv, ENETSW_SWMODE_REG); -- val |= ENETSW_SWMODE_FWD_EN_MASK; -- enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -- -- /* enable jumbo on all ports */ -- enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -- enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -- - /* initialize flow control buffer allocation */ - enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, - ENETDMA_BUFALLOC_REG(priv->rx_chan)); -@@ -2727,6 +2742,9 @@ static int bcm_enetsw_probe(struct platf - struct bcm63xx_enetsw_platform_data *pd; - struct resource *res_mem; - int ret, irq_rx, irq_tx; -+ unsigned i, num_ports = 0; -+ u16 port_mask = BIT(8); -+ u8 val; - - /* stop if shared driver failed, assume driver->probe will be - * called in the same order we register devices (correct ?) -@@ -2816,6 +2834,43 @@ static int bcm_enetsw_probe(struct platf - priv->pdev = pdev; - priv->net_dev = dev; - -+ /* reset mib */ -+ val = enetsw_readb(priv, ENETSW_GMCR_REG); -+ val |= ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ val &= ~ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ -+ /* force CPU port state */ -+ val = enetsw_readb(priv, ENETSW_IMPOV_REG); -+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -+ -+ /* enable switch forward engine */ -+ val = enetsw_readb(priv, ENETSW_SWMODE_REG); -+ val |= ENETSW_SWMODE_FWD_EN_MASK; -+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -+ -+ /* enable jumbo on all ports */ -+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -+ -+ for (i = 0; i < priv->num_ports; i++) { -+ struct bcm63xx_enetsw_port *port = &priv->used_ports[i]; -+ -+ if (!port->used) -+ continue; -+ -+ num_ports++; -+ port_mask |= BIT(i); -+ } -+ -+ /* only register if there is more than one external port */ -+ if (num_ports > 1) -+ bcmenet_switch_register(priv, port_mask); -+ - return 0; - - out_put_clk: -@@ -2844,6 +2899,9 @@ static int bcm_enetsw_remove(struct plat - priv = netdev_priv(dev); - unregister_netdev(dev); - -+ /* remove switch */ -+ bcmenet_switch_unregister(priv); -+ - /* release device resources */ - iounmap(priv->base); - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); diff --git a/target/linux/brcm63xx/patches-3.9/500-board-D4PW.patch b/target/linux/brcm63xx/patches-3.9/500-board-D4PW.patch deleted file mode 100644 index fb469703a5..0000000000 --- a/target/linux/brcm63xx/patches-3.9/500-board-D4PW.patch +++ /dev/null @@ -1,67 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -555,6 +555,56 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - }; -+ -+static struct board_info __initdata board_96348_D4PW = { -+ .name = "D-4P-W", -+ .expected_cpu_id = 0x6348, -+ -+ .has_enet1 = 1, -+ .has_pci = 1, -+ .has_uart0 = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "D-4P-W:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W::status", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W:green:internet", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W:red:internet", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 7, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -732,6 +782,7 @@ static const struct board_info __initcon - &board_DV201AMR, - &board_96348gw_a, - &board_rta1025w_16, -+ &board_96348_D4PW, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/501-board-NB4.patch b/target/linux/brcm63xx/patches-3.9/501-board-NB4.patch deleted file mode 100644 index 94da7ba149..0000000000 --- a/target/linux/brcm63xx/patches-3.9/501-board-NB4.patch +++ /dev/null @@ -1,650 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -15,6 +15,8 @@ - #include - #include - #include -+#include -+#include - #include - #include - #include -@@ -49,6 +51,12 @@ - #define CFE_OFFSET_64K 0x10000 - #define CFE_OFFSET_128K 0x20000 - -+#define NB4_PID_OFFSET 0xff80 -+#define NB4_74X164_GPIO_BASE 64 -+#define NB4_SPI_GPIO_MOSI 7 -+#define NB4_SPI_GPIO_CLK 6 -+#define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) -+ - static struct board_info board; - - /* -@@ -754,6 +762,596 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - }; -+ -+struct spi_gpio_platform_data nb4_spi_gpio_data = { -+ .sck = NB4_SPI_GPIO_CLK, -+ .mosi = NB4_SPI_GPIO_MOSI, -+ .miso = SPI_GPIO_NO_MISO, -+ .num_chipselect = 1, -+}; -+ -+ -+static struct platform_device nb4_spi_gpio = { -+ .name = "spi_gpio", -+ .id = 1, -+ .dev = { -+ .platform_data = &nb4_spi_gpio_data, -+ }, -+}; -+ -+static struct platform_device * __initdata nb4_devices[] = { -+ &nb4_spi_gpio, -+}; -+ -+const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = { -+ .base = NB4_74X164_GPIO_BASE -+}; -+ -+static struct spi_board_info nb4_spi_devices[] = { -+ { -+ .modalias = "74x164", -+ .max_speed_hz = 781000, -+ .bus_num = 1, -+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, -+ .mode = SPI_MODE_0, -+ .platform_data = &nb4_74x164_platform_data -+ } -+}; -+ -+static struct board_info __initdata board_nb4_ser_r0 = { -+ .name = "NB4-SER-r0", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r0:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_ser_r1 = { -+ .name = "NB4-SER-r1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r1:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_ser_r2 = { -+ .name = "NB4-SER-r2", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r2:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_fxc_r1 = { -+ .name = "NB4-FXC-r1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-FXC-r1:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:wifi", -+ .gpio = 15, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:red:service", -+ .gpio = 29, -+ }, -+ { -+ .name = "NB4-FXC-r1:green:service", -+ .gpio = 30, -+ }, -+ { -+ .name = "NB4-FXC-r1:blue:service", -+ .gpio = 4, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_fxc_r2 = { -+ .name = "NB4-FXC-r2", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-FXC-r2:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:wifi", -+ .gpio = 15, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:red:service", -+ .gpio = 29, -+ }, -+ { -+ .name = "NB4-FXC-r2:green:service", -+ .gpio = 30, -+ }, -+ { -+ .name = "NB4-FXC-r2:blue:service", -+ .gpio = 4, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; - #endif - - /* -@@ -790,6 +1388,11 @@ static const struct board_info __initcon - &board_96358vw2, - &board_AGPFS0, - &board_DWVS0, -+ &board_nb4_ser_r0, -+ &board_nb4_ser_r1, -+ &board_nb4_ser_r2, -+ &board_nb4_fxc_r1, -+ &board_nb4_fxc_r2, - #endif - }; - -@@ -844,6 +1447,16 @@ static void __init boardid_fixup(u8 *boo - struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); - char *board_name = (char *)bcm63xx_nvram_get_name(); - -+ if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) { -+ u8 *p = boot_addr + NB4_PID_OFFSET; -+ -+ /* Extract nb4 PID */ -+ if (!memcmp(p, "NB4-", 4)) { -+ memcpy(board_name, p, sizeof("NB4-XXX-rX")); -+ return; -+ } -+ } -+ - /* check if bcm_tag is at 64k offset */ - if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* else try 128k */ diff --git a/target/linux/brcm63xx/patches-3.9/502-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-3.9/502-board-96338W2_E7T.patch deleted file mode 100644 index 5baa1d391d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/502-board-96338W2_E7T.patch +++ /dev/null @@ -1,51 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -226,6 +226,40 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_96338w2_e7t = { -+ .name = "96338W2_E7T", -+ .expected_cpu_id = 0x6338, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "96338W2_E7T:green:ppp", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "96338W2_E7T:green:ppp-fail", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "96338W2_E7T:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ -+ }, -+ }, -+}; - #endif - - /* -@@ -1367,6 +1401,7 @@ static const struct board_info __initcon - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, - &board_96338w, -+ &board_96338w2_e7t, - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.9/503-board-CPVA642.patch b/target/linux/brcm63xx/patches-3.9/503-board-CPVA642.patch deleted file mode 100644 index 810aca0962..0000000000 --- a/target/linux/brcm63xx/patches-3.9/503-board-CPVA642.patch +++ /dev/null @@ -1,109 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -753,6 +753,98 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_CPVA642 = { -+ .name = "CPVA642", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "CPVA642:red:power", -+ .gpio = 14, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:power", -+ .gpio = 11, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "CPVA642:red:wifi", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:wifi", -+ .gpio = 28, -+ .active_low = 0, -+ }, -+ { -+ .name = "CPVA642:red:link", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:link", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:ether", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:phone1", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:phone2", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:usb", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ - static struct board_info __initdata board_AGPFS0 = { - .name = "AGPF-S0", - .expected_cpu_id = 0x6358, -@@ -1422,6 +1514,7 @@ static const struct board_info __initcon - &board_96358vw, - &board_96358vw2, - &board_AGPFS0, -+ &board_CPVA642, - &board_DWVS0, - &board_nb4_ser_r0, - &board_nb4_ser_r1, diff --git a/target/linux/brcm63xx/patches-3.9/504-board_dsl_274xb_rev_c.patch b/target/linux/brcm63xx/patches-3.9/504-board_dsl_274xb_rev_c.patch deleted file mode 100644 index 29bbde3f01..0000000000 --- a/target/linux/brcm63xx/patches-3.9/504-board_dsl_274xb_rev_c.patch +++ /dev/null @@ -1,72 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -889,6 +889,61 @@ static struct board_info __initdata boar - .has_ohci0 = 1, - }; - -+/* D-Link DSL-274xB revison C2/C3 */ -+static struct board_info __initdata board_dsl_274xb_rev_c = { -+ .name = "AW4139", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "dsl-274xb:green:power", -+ .gpio = 5, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "dsl-274xb:red:power", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:adsl", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:internet", -+ .gpio = 2, -+ }, -+ { -+ .name = "dsl-274xb:red:internet", -+ .gpio = 10, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - struct spi_gpio_platform_data nb4_spi_gpio_data = { - .sck = NB4_SPI_GPIO_CLK, - .mosi = NB4_SPI_GPIO_MOSI, -@@ -1516,6 +1571,7 @@ static const struct board_info __initcon - &board_AGPFS0, - &board_CPVA642, - &board_DWVS0, -+ &board_dsl_274xb_rev_c, - &board_nb4_ser_r0, - &board_nb4_ser_r1, - &board_nb4_ser_r2, diff --git a/target/linux/brcm63xx/patches-3.9/505-board_spw500v.patch b/target/linux/brcm63xx/patches-3.9/505-board_spw500v.patch deleted file mode 100644 index 4270f7ff6c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/505-board_spw500v.patch +++ /dev/null @@ -1,78 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -647,6 +647,67 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_spw500v = { -+ .name = "SPW500V", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 6, -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "SPW500V:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "SPW500V:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "SPW500V:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { .name = "SPW500V:green:pstn", -+ .gpio = 28, -+ .active_low = 1, -+ }, -+ { -+ .name = "SPW500V:green:voip", -+ .gpio = 32, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -1563,6 +1624,7 @@ static const struct board_info __initcon - &board_96348gw_a, - &board_rta1025w_16, - &board_96348_D4PW, -+ &board_spw500v, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/506-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-3.9/506-board_gw6200_gw6000.patch deleted file mode 100644 index 658f7f1d4f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/506-board_gw6200_gw6000.patch +++ /dev/null @@ -1,124 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -514,6 +514,112 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_gw6200 = { -+ .name = "GW6200", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 8, /* FIXME: What is real GPIO here? */ -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "GW6200:green:line1", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:line2", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:line3", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:tel", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+static struct board_info __initdata board_gw6000 = { -+ .name = "GW6000", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 6, -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ /* GW6000 has no GPIO-controlled leds */ -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ -+ - static struct board_info __initdata board_FAST2404 = { - .name = "F@ST2404", - .expected_cpu_id = 0x6348, -@@ -1617,6 +1723,8 @@ static const struct board_info __initcon - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, - &board_96348gw, -+ &board_gw6000, -+ &board_gw6200, - &board_96348gw_10, - &board_96348gw_11, - &board_FAST2404, diff --git a/target/linux/brcm63xx/patches-3.9/507-board-MAGIC.patch b/target/linux/brcm63xx/patches-3.9/507-board-MAGIC.patch deleted file mode 100644 index 19403d8b07..0000000000 --- a/target/linux/brcm63xx/patches-3.9/507-board-MAGIC.patch +++ /dev/null @@ -1,89 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -814,6 +814,78 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_96348sv = { -+ .name = "MAGIC", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ /* it has BP_ENET_EXTERNAL_PHY */ -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 25, -+ .gpio_int = 34, -+ .cs = 2, -+ .ext_irq = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "MAGIC:green:voip", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:adsl", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:wifi", -+ .gpio = 28, -+ }, -+ { -+ .name = "MAGIC:green:usb", -+ .gpio = 35, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:hpna", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "MAGIC:green:stop", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1733,6 +1805,7 @@ static const struct board_info __initcon - &board_rta1025w_16, - &board_96348_D4PW, - &board_spw500v, -+ &board_96348sv, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/508-board_hw553.patch b/target/linux/brcm63xx/patches-3.9/508-board_hw553.patch deleted file mode 100644 index 1370c6c19e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/508-board_hw553.patch +++ /dev/null @@ -1,93 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1772,6 +1772,82 @@ static struct board_info __initdata boar - .spis = nb4_spi_devices, - .num_spis = ARRAY_SIZE(nb4_spi_devices), - }; -+ -+static struct board_info __initdata board_HW553 = { -+ .name = "HW553", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "HW553:red:lan", -+ .gpio = 34, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:lan", -+ .gpio = 35, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:adsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:adsl", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:power", -+ .gpio = 5, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ -+ { -+ .name = "HW553:blue:power", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:wifi", -+ .gpio = 25, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:internetkey", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:internetkey", -+ .gpio = 13, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1820,6 +1896,7 @@ static const struct board_info __initcon - &board_nb4_ser_r2, - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, -+ &board_HW553, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.9/509-board_rta1320_16m.patch b/target/linux/brcm63xx/patches-3.9/509-board_rta1320_16m.patch deleted file mode 100644 index a84c89755f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/509-board_rta1320_16m.patch +++ /dev/null @@ -1,56 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -260,6 +260,45 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_rta1320_16m = { -+ .name = "RTA1320_16M", -+ .expected_cpu_id = 0x6338, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA1320_16M:green:adsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA1320_16M:green:ppp", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA1320_16M:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "RTA1320_16M:green:stop", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1864,6 +1903,7 @@ static const struct board_info __initcon - &board_96338gw, - &board_96338w, - &board_96338w2_e7t, -+ &board_rta1320_16m, - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.9/510-board_spw303v.patch b/target/linux/brcm63xx/patches-3.9/510-board_spw303v.patch deleted file mode 100644 index 328233b564..0000000000 --- a/target/linux/brcm63xx/patches-3.9/510-board_spw303v.patch +++ /dev/null @@ -1,83 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1887,6 +1887,72 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+ /* T-Home Speedport W 303V Typ B */ -+static struct board_info __initdata board_spw303v = { -+ .name = "96358-502V", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "spw303v:green:power+adsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:red:power+adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:ppp", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:ses", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:voip", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:pots", -+ .gpio = 31, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "ses", -+ .gpio = 37, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ } -+}; - #endif - - /* -@@ -1937,6 +2003,7 @@ static const struct board_info __initcon - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, - &board_HW553, -+ &board_spw303v, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch deleted file mode 100644 index d0b33803e8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/511-board_V2500V.patch +++ /dev/null @@ -1,123 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -925,6 +925,65 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_V2500V_BB = { -+ .name = "V2500V_BB", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "V2500V_BB:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "V2500V_BB:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2500V_BB:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { .name = "V2500V_BB:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2500V_BB:green:wireless", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 31, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -1988,6 +2047,7 @@ static const struct board_info __initcon - &board_96348_D4PW, - &board_spw500v, - &board_96348sv, -+ &board_V2500V_BB, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 -@@ -2109,6 +2169,22 @@ void __init board_prom_init(void) - val &= MPI_CSBASE_BASE_MASK; - } - boot_addr = (u8 *)KSEG1ADDR(val); -+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr); -+ -+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */ -+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/ -+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */ -+ /* Do an early check of CFE and then select bank 0 */ -+ -+ if (boot_addr == (u8 *)0xbf800000) { -+ u8 *tmp_boot_addr = (u8*)0xbfc00000; -+ -+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET); -+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) { -+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n"); -+ boot_addr = tmp_boot_addr; -+ } -+ } - - /* dump cfe version */ - cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -19,6 +19,7 @@ - #include - #include - -+#include - #include - #include - #include -@@ -158,6 +159,13 @@ int __init bcm63xx_flash_register(int nu - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); - val &= MPI_CSBASE_BASE_MASK; - -+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */ -+ /* Loading from CFE always uses Bank 0 */ -+ if (!strcmp(board_get_name(), "V2500V_BB")) { -+ pr_info("V2500V: Start in Bank 0\n"); -+ val = val + 0x400000; // Select Bank 0 start address -+ } -+ - mtd_resources[0].start = val; - mtd_resources[0].end = 0x1FFFFFFF; - diff --git a/target/linux/brcm63xx/patches-3.9/512-board_BTV2110.patch b/target/linux/brcm63xx/patches-3.9/512-board_BTV2110.patch deleted file mode 100644 index d4fe2fa8f3..0000000000 --- a/target/linux/brcm63xx/patches-3.9/512-board_BTV2110.patch +++ /dev/null @@ -1,75 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -485,6 +485,64 @@ static struct board_info __initdata boar - }, - }; - -+ -+/* BT Voyager 2110 */ -+static struct board_info __initdata board_V2110 = { -+ .name = "V2110", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "V2110:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "V2110:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2110:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { .name = "V2110:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2110:green:wireless", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2048,6 +2106,7 @@ static const struct board_info __initcon - &board_spw500v, - &board_96348sv, - &board_V2500V_BB, -+ &board_V2110, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/513-board_livebox.patch b/target/linux/brcm63xx/patches-3.9/513-board_livebox.patch deleted file mode 100644 index 2323b5eef7..0000000000 --- a/target/linux/brcm63xx/patches-3.9/513-board_livebox.patch +++ /dev/null @@ -1,390 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/Kconfig -+++ b/arch/mips/bcm63xx/boards/Kconfig -@@ -8,4 +8,10 @@ config BOARD_BCM963XX - select SSB - help - -+config BOARD_LIVEBOX -+ bool "Inventel Livebox(es) boards" -+ select SSB -+ help -+ Inventel Livebox boards using the RedBoot bootloader. -+ - endchoice ---- a/arch/mips/bcm63xx/boards/Makefile -+++ b/arch/mips/bcm63xx/boards/Makefile -@@ -1 +1,2 @@ - obj-$(CONFIG_BOARD_BCM963XX) += board_bcm963xx.o -+obj-$(CONFIG_BOARD_LIVEBOX) += board_livebox.o ---- /dev/null -+++ b/arch/mips/bcm63xx/boards/board_livebox.c -@@ -0,0 +1,369 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Florian Fainelli -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define PFX "board_livebox: " -+ -+#define LIVEBOX_KEYS_POLL_INTERVAL 20 -+#define LIVEBOX_KEYS_DEBOUNCE_INTERVAL (LIVEBOX_KEYS_POLL_INTERVAL * 3) -+ -+static unsigned int mac_addr_used = 0; -+static struct board_info board; -+ -+/* -+ * known 6348 boards -+ */ -+#ifdef CONFIG_BCM63XX_CPU_6348 -+static struct board_info __initdata board_livebox_blue5g = { -+ .name = "Livebox-blue-5g", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 31, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ -+ .has_dsp = 0, /*TODO some Liveboxes have dsp*/ -+ .dsp = { -+ .gpio_rst = 6, /*FIXME eth1 shares gpio6 with dsp?*/ -+ .gpio_int = 35, -+ .cs = 2, -+ .ext_irq = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "Livebox-blue-5g::adsl-fail", -+ .gpio = 0, -+ .active_low = 0, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "Livebox-blue-5g::adsl", -+ .gpio = 1, -+ }, -+ { -+ .name = "Livebox-blue-5g::traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "Livebox-blue-5g::phone", -+ .gpio = 3, -+ }, -+ { -+ .name = "Livebox-blue-5g::wifi", -+ .gpio = 4, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "BTN_1", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "BTN_2", -+ .gpio = 7, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_2, -+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ -+ }, -+}; -+#endif -+ -+/* -+ * all boards -+ */ -+static const struct board_info __initdata *bcm963xx_boards[] = { -+#ifdef CONFIG_BCM63XX_CPU_6348 -+ &board_livebox_blue5g -+#endif -+}; -+/* -+ * return board name for /proc/cpuinfo -+ */ -+const char *board_get_name(void) -+{ -+ return board.name; -+} -+ -+/* -+ * register & return a new board mac address -+ */ -+static int board_get_mac_address(u8 *mac) -+{ -+ u8 *p; -+ int count; -+ -+ memcpy(mac, (u8 *)0xBEBFF377, ETH_ALEN); -+ -+ p = mac + ETH_ALEN - 1; -+ count = mac_addr_used; -+ -+ while (count--) { -+ do { -+ (*p)++; -+ if (*p != 0) -+ break; -+ p--; -+ } while (p != mac); -+ } -+ -+ if (p == mac) { -+ printk(KERN_ERR PFX "unable to fetch mac address\n"); -+ return -ENODEV; -+ } -+ mac_addr_used++; -+ -+ return 0; -+} -+ -+/* -+ * early init callback -+ */ -+#define LIVEBOX_GPIO_DETECT_MASK 0x000000ff -+#define LIVEBOX_BOOT_ADDR 0x1e400000 -+ -+#define LIVEBOX_HW_BLUE5G_9 0x90 -+ -+void __init board_prom_init(void) -+{ -+ u32 val; -+ u8 hw_version; -+ -+ /* Get hardware version */ -+ val = bcm_gpio_readl(GPIO_CTL_LO_REG); -+ val &= ~LIVEBOX_GPIO_DETECT_MASK; -+ bcm_gpio_writel(val, GPIO_CTL_LO_REG); -+ -+ hw_version = bcm_gpio_readl(GPIO_DATA_LO_REG) & LIVEBOX_GPIO_DETECT_MASK; -+ switch (hw_version) { -+ case LIVEBOX_HW_BLUE5G_9: -+ printk(KERN_INFO PFX "Livebox BLUE5G.9\n"); -+ memcpy(&board, bcm963xx_boards[0], sizeof(board)); -+ break; -+ default: -+ printk(KERN_INFO PFX "Unknown livebox version: %02x\n", hw_version); -+ break; -+ } -+ -+ /* use default livebox configuration */ -+ memcpy(&board, bcm963xx_boards[0], sizeof(board)); -+ -+ /* setup pin multiplexing depending on board enabled device, -+ * this has to be done this early since PCI init is done -+ * inside arch_initcall */ -+ val = 0; -+ -+#ifdef CONFIG_PCI -+ if (board.has_pci) { -+ bcm63xx_pci_enabled = 1; -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G2_PCI; -+ } -+#endif -+ if (board.has_pccard) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G1_MII_PCCARD; -+ } -+ -+ if (board.has_enet0 && !board.enet0.use_internal_phy) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G3_EXT_MII | -+ GPIO_MODE_6348_G0_EXT_MII; -+ } -+ -+ if (board.has_enet1 && !board.enet1.use_internal_phy) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G3_EXT_MII | -+ GPIO_MODE_6348_G0_EXT_MII; -+ printk(KERN_INFO PFX "resetting gpio6 for eth1...\n"); -+ gpio_request(6, "dsp_eth_rst"); -+ gpio_direction_output(6, 0); -+ gpio_set_value(6, 1); -+ } -+ -+ bcm_gpio_writel(val, GPIO_MODE_REG); -+} -+ -+/* -+ * second stage init callback, good time to panic if we couldn't -+ * identify on which board we're running since early printk is working -+ */ -+void __init board_setup(void) -+{ -+ if (!board.name[0]) -+ panic("unable to detect bcm963xx board"); -+ printk(KERN_INFO PFX "board name: %s\n", board.name); -+ -+ /* make sure we're running on expected cpu */ -+ if (bcm63xx_get_cpu_id() != board.expected_cpu_id) -+ panic("unexpected CPU for bcm963xx board"); -+} -+ -+static struct physmap_flash_data flash_data = { -+ .width = 2, -+}; -+ -+static struct resource mtd_resources[] = { -+ { -+ .start = 0, /* filled at runtime */ -+ .end = 0, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ -+static struct platform_device mtd_dev = { -+ .name = "physmap-flash", -+ .resource = mtd_resources, -+ .num_resources = ARRAY_SIZE(mtd_resources), -+ .dev = { -+ .platform_data = &flash_data, -+ }, -+}; -+ -+static struct gpio_led_platform_data bcm63xx_led_data; -+ -+static struct platform_device bcm63xx_gpio_leds = { -+ .name = "leds-gpio", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_led_data, -+}; -+ -+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = { -+ .poll_interval = LIVEBOX_KEYS_POLL_INTERVAL, -+}; -+ -+static struct platform_device bcm63xx_gpio_keys_device = { -+ .name = "gpio-keys-polled", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_gpio_keys_data, -+}; -+ -+/* -+ * third stage init callback, register all board devices. -+ */ -+int __init board_register_devices(void) -+{ -+ u32 val; -+ int led_count = 0; -+ int button_count = 0; -+ -+ if (board.has_uart0) -+ bcm63xx_uart_register(0); -+ -+ if (board.has_uart1) -+ bcm63xx_uart_register(1); -+ -+ if (board.has_pccard) -+ bcm63xx_pcmcia_register(); -+ -+ if (board.has_enet0 && -+ !board_get_mac_address(board.enet0.mac_addr)) -+ bcm63xx_enet_register(0, &board.enet0); -+ -+ if (board.has_enet1 && -+ !board_get_mac_address(board.enet1.mac_addr)) -+ bcm63xx_enet_register(1, &board.enet1); -+ -+ if (board.has_ehci0) -+ bcm63xx_ehci_register(); -+ -+ if (board.has_ohci0) -+ bcm63xx_ohci_register(); -+ -+ if (board.has_dsp) -+ bcm63xx_dsp_register(&board.dsp); -+ -+ bcm63xx_spi_register(); -+ -+ if (board.num_devs) -+ platform_add_devices(board.devs, board.num_devs); -+ -+ if (board.num_spis) -+ spi_register_board_info(board.spis, board.num_spis); -+ -+ -+ /* read base address of boot chip select (0) */ -+ val = bcm_mpi_readl(MPI_CSBASE_REG(0)); -+ val &= MPI_CSBASE_BASE_MASK; -+ if (val != LIVEBOX_BOOT_ADDR) -+ printk(KERN_NOTICE PFX "flash address is: 0x%08x, forcing to: 0x%08x\n", -+ val, LIVEBOX_BOOT_ADDR); -+ mtd_resources[0].start = LIVEBOX_BOOT_ADDR; -+ mtd_resources[0].end = 0x1ebfffff; -+ -+ platform_device_register(&mtd_dev); -+ -+ /* count number of LEDs defined by this device */ -+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) -+ led_count++; -+ -+ bcm63xx_led_data.num_leds = led_count; -+ bcm63xx_led_data.leds = board.leds; -+ -+ platform_device_register(&bcm63xx_gpio_leds); -+ -+ /* count number of BUTTONs defined by this device */ -+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) -+ button_count++; -+ -+ if (button_count) { -+ bcm63xx_gpio_keys_data.nbuttons = button_count; -+ bcm63xx_gpio_keys_data.buttons = board.buttons; -+ -+ platform_device_register(&bcm63xx_gpio_keys_device); -+ } -+ -+ return 0; -+} diff --git a/target/linux/brcm63xx/patches-3.9/514-board_ct536_ct5621.patch b/target/linux/brcm63xx/patches-3.9/514-board_ct536_ct5621.patch deleted file mode 100644 index 6f2e25a660..0000000000 --- a/target/linux/brcm63xx/patches-3.9/514-board_ct536_ct5621.patch +++ /dev/null @@ -1,62 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -543,6 +543,51 @@ static struct board_info __initdata boar - }; - - -+static struct board_info __initdata board_ct536_ct5621 = { -+ .name = "CT536_CT5621", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 0, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "CT536_CT5621:green:adsl-fail", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT536_CT5621:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2107,6 +2152,7 @@ static const struct board_info __initcon - &board_96348sv, - &board_V2500V_BB, - &board_V2110, -+ &board_ct536_ct5621, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/515-board_DWV-S0_fixes.patch b/target/linux/brcm63xx/patches-3.9/515-board_DWV-S0_fixes.patch deleted file mode 100644 index d451407524..0000000000 --- a/target/linux/brcm63xx/patches-3.9/515-board_DWV-S0_fixes.patch +++ /dev/null @@ -1,19 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1312,6 +1312,8 @@ static struct board_info __initdata boar - .name = "DWV-S0", - .expected_cpu_id = 0x6358, - -+ .has_uart0 = 1, -+ - .has_enet0 = 1, - .has_enet1 = 1, - .has_pci = 1, -@@ -1327,6 +1329,7 @@ static struct board_info __initdata boar - }, - - .has_ohci0 = 1, -+ .has_ehci0 = 1, - }; - - /* D-Link DSL-274xB revison C2/C3 */ diff --git a/target/linux/brcm63xx/patches-3.9/516-board_96348A-122.patch b/target/linux/brcm63xx/patches-3.9/516-board_96348A-122.patch deleted file mode 100644 index 6541419050..0000000000 --- a/target/linux/brcm63xx/patches-3.9/516-board_96348A-122.patch +++ /dev/null @@ -1,80 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -588,6 +588,69 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96348A_122 = { -+ .name = "96348A-122", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348A-122:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96348A-122:red:alarm", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348A-122:green:wps", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 35, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2156,6 +2219,7 @@ static const struct board_info __initcon - &board_V2500V_BB, - &board_V2110, - &board_ct536_ct5621, -+ &board_96348A_122, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/517-RTA1205W_16_uart_fixes.patch b/target/linux/brcm63xx/patches-3.9/517-RTA1205W_16_uart_fixes.patch deleted file mode 100644 index c3756148c2..0000000000 --- a/target/linux/brcm63xx/patches-3.9/517-RTA1205W_16_uart_fixes.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -853,6 +853,7 @@ static struct board_info __initdata boar - .name = "RTA1025W_16", - .expected_cpu_id = 0x6348, - -+ .has_uart0 = 1, - .has_enet0 = 1, - .has_enet1 = 1, - .has_pci = 1, diff --git a/target/linux/brcm63xx/patches-3.9/519_board_CPVA502plus.patch b/target/linux/brcm63xx/patches-3.9/519_board_CPVA502plus.patch deleted file mode 100644 index ba1a39fc18..0000000000 --- a/target/linux/brcm63xx/patches-3.9/519_board_CPVA502plus.patch +++ /dev/null @@ -1,57 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1151,6 +1151,46 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_CPVA502plus = { -+ .name = "CPVA502+", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "CPVA502+:green:phone", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA502+:green:link", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA502+:green:feth1", /* FIXME:does gpio4 enable eth1 phy? */ -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+}; -+ - #endif - - /* -@@ -2221,6 +2261,7 @@ static const struct board_info __initcon - &board_V2110, - &board_ct536_ct5621, - &board_96348A_122, -+ &board_CPVA502plus, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/520-bcm63xx-add-support-for-96368MVWG-board.patch b/target/linux/brcm63xx/patches-3.9/520-bcm63xx-add-support-for-96368MVWG-board.patch deleted file mode 100644 index bc5bd3d83e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/520-bcm63xx-add-support-for-96368MVWG-board.patch +++ /dev/null @@ -1,128 +0,0 @@ -From eeacc2529942051504bc957726aa178671344421 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon -Date: Wed, 20 Jan 2010 16:21:30 +0100 -Subject: [PATCH 32/63] bcm63xx: add support for 96368MVWG board. - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 95 ++++++++++++++++++++ - .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 + - 2 files changed, 97 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2225,6 +2225,78 @@ static struct board_info __initdata boar - #endif - - /* -+ * known 6368 boards -+ */ -+#ifdef CONFIG_BCM63XX_CPU_6368 -+static struct board_info __initdata board_96368mvwg = { -+ .name = "96368MVWG", -+ .expected_cpu_id = 0x6368, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "port1", -+ }, -+ -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "port2", -+ }, -+ -+ [4] = { -+ .used = 1, -+ .phy_id = 0x12, -+ .name = "port0", -+ }, -+ -+ [5] = { -+ .used = 1, -+ .phy_id = 0x11, -+ .name = "port3", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96368MVWG:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVWG:green:ppp", -+ .gpio = 5, -+ }, -+ { -+ .name = "96368MVWG:green:power", -+ .gpio = 22, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96368MVWG:green:wps", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVWG:green:ppp-fail", -+ .gpio = 31, -+ }, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+}; -+#endif -+ -+/* - * all boards - */ - static const struct board_info __initconst *bcm963xx_boards[] = { -@@ -2279,6 +2351,10 @@ static const struct board_info __initcon - &board_HW553, - &board_spw303v, - #endif -+ -+#ifdef CONFIG_BCM63XX_CPU_6368 -+ &board_96368mvwg, -+#endif - }; - - /* -@@ -2460,12 +2536,25 @@ void __init board_prom_init(void) - bcm63xx_pci_enabled = 1; - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G2_PCI; -+ -+ if (BCMCPU_IS_6368()) -+ val |= GPIO_MODE_6368_PCI_REQ1 | -+ GPIO_MODE_6368_PCI_GNT1 | -+ GPIO_MODE_6368_PCI_INTB | -+ GPIO_MODE_6368_PCI_REQ0 | -+ GPIO_MODE_6368_PCI_GNT0; - } - #endif - - if (board.has_pccard) { - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G1_MII_PCCARD; -+ -+ if (BCMCPU_IS_6368()) -+ val |= GPIO_MODE_6368_PCMCIA_CD1 | -+ GPIO_MODE_6368_PCMCIA_CD2 | -+ GPIO_MODE_6368_PCMCIA_VS1 | -+ GPIO_MODE_6368_PCMCIA_VS2; - } - - if (board.has_enet0 && !board.enet0.use_internal_phy) { diff --git a/target/linux/brcm63xx/patches-3.9/521-bcm63xx-add-support-for-96368MVNgr-board.patch b/target/linux/brcm63xx/patches-3.9/521-bcm63xx-add-support-for-96368MVNgr-board.patch deleted file mode 100644 index bcda63fa7d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/521-bcm63xx-add-support-for-96368MVNgr-board.patch +++ /dev/null @@ -1,92 +0,0 @@ -From f457fc2eb9bb915b5a4d251c7c68d4694cf07b01 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon -Date: Fri, 4 Nov 2011 12:33:48 +0100 -Subject: [PATCH 33/63] bcm63xx: add support for 96368MVNgr board. - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 67 +++++++++++++++++++++++++++++ - 1 files changed, 67 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2294,6 +2294,72 @@ static struct board_info __initdata boar - .has_ohci0 = 1, - .has_ehci0 = 1, - }; -+ -+static struct board_info __initdata board_96368mvngr = { -+ .name = "96368MVNgr", -+ .expected_cpu_id = 0x6368, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "port1", -+ }, -+ -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "port2", -+ }, -+ -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "port3", -+ }, -+ -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "port4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96368MVNgr:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVNgr:green:inet", -+ .gpio = 5, -+ }, -+ { -+ .name = "96368MVNgr:green:power", -+ .gpio = 22, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96368MVNgr:green:wps", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVNgr:green:inet-fail", -+ .gpio = 3, -+ }, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+}; - #endif - - /* -@@ -2354,6 +2420,7 @@ static const struct board_info __initcon - - #ifdef CONFIG_BCM63XX_CPU_6368 - &board_96368mvwg, -+ &board_96368mvngr, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.9/522-MIPS-BCM63XX-add-96328avng-reference-board.patch b/target/linux/brcm63xx/patches-3.9/522-MIPS-BCM63XX-add-96328avng-reference-board.patch deleted file mode 100644 index c8c098d9e6..0000000000 --- a/target/linux/brcm63xx/patches-3.9/522-MIPS-BCM63XX-add-96328avng-reference-board.patch +++ /dev/null @@ -1,67 +0,0 @@ -From c93c2bbf0cc96da5a47d77f01daf6c983cfe4216 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 29 May 2012 10:52:25 +0200 -Subject: [PATCH] MIPS: BCM63XX: add 96328avng reference board - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 77 +++++++++++++++++++++++++++++ - 1 files changed, 77 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -108,13 +108,45 @@ static struct board_info __initdata boar - .port_no = 0, - }, - -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ - .leds = { - { -- .name = "96328avng::ppp-fail", -+ .name = "96328avng::internet-fail", - .gpio = 2, - .active_low = 1, - }, - { -+ .name = "96328avng::dsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { - .name = "96328avng::power", - .gpio = 4, - .active_low = 1, -@@ -131,7 +163,7 @@ static struct board_info __initdata boar - .active_low = 1, - }, - { -- .name = "96328avng::ppp", -+ .name = "96328avng::internet", - .gpio = 11, - .active_low = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.9/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch b/target/linux/brcm63xx/patches-3.9/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch deleted file mode 100644 index c392e78376..0000000000 --- a/target/linux/brcm63xx/patches-3.9/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch +++ /dev/null @@ -1,96 +0,0 @@ -From f0649f7b7c672cf452a1796a1422bf615e1973f8 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Tue, 29 May 2012 11:01:12 +0200 -Subject: [PATCH] MIPS: BCM63XX: add 963281TAN reference board - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 71 +++++++++++++++++++++++++++++ - 1 files changed, 71 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -169,6 +169,76 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_963281TAN = { -+ .name = "963281TAN", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "963281TAN::internet", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "963281TAN::internet-fail", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::power-fail", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::wps", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::dsl", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ -+ }, -+}; - #endif - - /* -@@ -2403,6 +2473,7 @@ static const struct board_info __initcon - #endif - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_963281TAN, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, diff --git a/target/linux/brcm63xx/patches-3.9/524-board_dsl_274xb_rev_f.patch b/target/linux/brcm63xx/patches-3.9/524-board_dsl_274xb_rev_f.patch deleted file mode 100644 index 06457c1d1d..0000000000 --- a/target/linux/brcm63xx/patches-3.9/524-board_dsl_274xb_rev_f.patch +++ /dev/null @@ -1,132 +0,0 @@ -From 66808f706b3dcd83a9f5157997ff478a880a2906 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski -Date: Mon, 30 Apr 2012 09:10:51 +0200 -Subject: [PATCH 70/79] MIPS: BCM63XX: Add board definition for D-Link - DSL-274xB rev F1 - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 104 +++++++++++++++++++++++++++++ - 1 files changed, 104 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -239,6 +239,111 @@ static struct board_info __initdata boar - - }, - }; -+ -+static struct board_info __initdata board_dsl_274xb_f1 = { -+ .name = "AW4339U", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0x7d1000, -+ .slot = 0, -+ .led_pin = -1, -+ }, -+ }, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 4", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 3", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 2", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 1", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "dsl-274xb:red:internet", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:dsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "dsl-274xb:red:power", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:blue:wps", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:internet", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "wifi", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 24, -+ .active_low = 1, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -2474,6 +2579,7 @@ static const struct board_info __initcon - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, - &board_963281TAN, -+ &board_dsl_274xb_f1, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, diff --git a/target/linux/brcm63xx/patches-3.9/525-board_96348w3.patch b/target/linux/brcm63xx/patches-3.9/525-board_96348w3.patch deleted file mode 100644 index 2d260f9cf1..0000000000 --- a/target/linux/brcm63xx/patches-3.9/525-board_96348w3.patch +++ /dev/null @@ -1,70 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1398,6 +1398,59 @@ static struct board_info __initdata boar - }, - }; - -+/* NetGear DG834G v4 */ -+static struct board_info __initdata board_96348W3 = { -+ .name = "96348W3", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348W3:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96348W3:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348W3::adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348W3::internet", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 6, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - #endif - - /* -@@ -2609,6 +2662,7 @@ static const struct board_info __initcon - &board_ct536_ct5621, - &board_96348A_122, - &board_CPVA502plus, -+ &board_96348W3, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.9/526-board_CT6373-1.patch b/target/linux/brcm63xx/patches-3.9/526-board_CT6373-1.patch deleted file mode 100644 index 34e3336164..0000000000 --- a/target/linux/brcm63xx/patches-3.9/526-board_CT6373-1.patch +++ /dev/null @@ -1,138 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -57,6 +57,13 @@ - #define NB4_SPI_GPIO_CLK 6 - #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) - -+#define CT6373_PID_OFFSET 0xff80 -+#define CT6373_74X164_GPIO_BASE 64 -+#define CT6373_SPI_GPIO_MOSI 7 -+#define CT6373_SPI_GPIO_CLK 6 -+#define CT6373_74HC64_GPIO(X) (CT6373_74X164_GPIO_BASE + (X)) -+ -+ - static struct board_info board; - - /* -@@ -2341,6 +2348,113 @@ static struct board_info __initdata boar - .num_spis = ARRAY_SIZE(nb4_spi_devices), - }; - -+ -+struct spi_gpio_platform_data ct6373_spi_gpio_data = { -+ .sck = CT6373_SPI_GPIO_CLK, -+ .mosi = CT6373_SPI_GPIO_MOSI, -+ .miso = SPI_GPIO_NO_MISO, -+ .num_chipselect = 1, -+}; -+ -+static struct platform_device ct6373_spi_gpio = { -+ .name = "spi_gpio", -+ .id = 1, -+ .dev = { -+ .platform_data = &ct6373_spi_gpio_data, -+ }, -+}; -+ -+static struct platform_device * __initdata ct6373_devices[] = { -+ &ct6373_spi_gpio, -+}; -+ -+const struct gen_74x164_chip_platform_data ct6373_74x164_platform_data = { -+ .base = CT6373_74X164_GPIO_BASE -+}; -+ -+static struct spi_board_info ct6373_spi_devices[] = { -+ { -+ .modalias = "74x164", -+ .max_speed_hz = 781000, -+ .bus_num = 1, -+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, -+ .mode = SPI_MODE_0, -+ .platform_data = &ct6373_74x164_platform_data -+ } -+}; -+ -+static struct board_info __initdata board_ct6373_1 = { -+ .name = "CT6373-1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "CT6373-1:green:power", -+ .gpio = 0, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "CT6373-1:green:usb", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:wlan", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:adsl", -+ .gpio = CT6373_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:line", -+ .gpio = CT6373_74HC64_GPIO(1), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:fxs1", -+ .gpio = CT6373_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:fxs2", -+ .gpio = CT6373_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 35, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ -+ .devs = ct6373_devices, -+ .num_devs = ARRAY_SIZE(ct6373_devices), -+ .spis = ct6373_spi_devices, -+ .num_spis = ARRAY_SIZE(ct6373_spi_devices), -+}; -+ - static struct board_info __initdata board_HW553 = { - .name = "HW553", - .expected_cpu_id = 0x6358, -@@ -2677,6 +2791,7 @@ static const struct board_info __initcon - &board_nb4_ser_r2, - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, -+ &board_ct6373_1, - &board_HW553, - &board_spw303v, - #endif diff --git a/target/linux/brcm63xx/patches-3.9/527-board_dva-g3810bn-tl-1.patch b/target/linux/brcm63xx/patches-3.9/527-board_dva-g3810bn-tl-1.patch deleted file mode 100644 index f63d4a0c2c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/527-board_dva-g3810bn-tl-1.patch +++ /dev/null @@ -1,84 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2596,6 +2596,73 @@ static struct board_info __initdata boar - }, - } - }; -+ -+/* D-Link DVA-G3810BN/TL */ -+static struct board_info __initdata board_DVAG3810BN = { -+ .name = "DVAG3810BN", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 0, -+ .use_internal_phy = 1, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "DVAG3810BN::voip", -+ .gpio = 1, -+ }, -+ { -+ .name = "DVAG3810BN::dsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "DVAG3810BN::internet", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "DVAG3810BN::power", -+ .gpio = 4, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "DVAG3810BN::stop", -+ .gpio = 5, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -2794,6 +2861,7 @@ static const struct board_info __initcon - &board_ct6373_1, - &board_HW553, - &board_spw303v, -+ &board_DVAG3810BN, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6368 diff --git a/target/linux/brcm63xx/patches-3.9/528-board_nb6.patch b/target/linux/brcm63xx/patches-3.9/528-board_nb6.patch deleted file mode 100644 index 8199cb653e..0000000000 --- a/target/linux/brcm63xx/patches-3.9/528-board_nb6.patch +++ /dev/null @@ -1,146 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -17,6 +17,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -56,6 +57,8 @@ - #define NB4_SPI_GPIO_MOSI 7 - #define NB4_SPI_GPIO_CLK 6 - #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) -+#define NB6_GPIO_RTL8367_SDA 18 -+#define NB6_GPIO_RTL8367_SCK 20 - - #define CT6373_PID_OFFSET 0xff80 - #define CT6373_74X164_GPIO_BASE 64 -@@ -2665,6 +2668,103 @@ static struct board_info __initdata boar - }; - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+static struct rtl8367_extif_config nb6_rtl8367_extif0_cfg = { -+ .mode = RTL8367_EXTIF_MODE_RGMII, -+ .txdelay = 1, -+ .rxdelay = 5, -+ .ability = { -+ .force_mode = 1, -+ .txpause = 1, -+ .rxpause = 1, -+ .link = 1, -+ .duplex = 1, -+ .speed = RTL8367_PORT_SPEED_1000, -+ }, -+}; -+ -+static struct rtl8367_platform_data nb6_rtl8367_data = { -+ .gpio_sda = NB6_GPIO_RTL8367_SDA, -+ .gpio_sck = NB6_GPIO_RTL8367_SCK, -+ .extif0_cfg = &nb6_rtl8367_extif0_cfg, -+}; -+ -+static struct platform_device nb6_rtl8367_device = { -+ .name = RTL8367_DRIVER_NAME, -+ .id = -1, -+ .dev = { -+ .platform_data = &nb6_rtl8367_data, -+ } -+}; -+ -+static struct platform_device * __initdata nb6_devices[] = { -+ &nb6_rtl8367_device, -+}; -+ -+static struct board_info __initdata board_nb6 = { -+ .name = "NB6", -+ .expected_cpu_id = 0x6362, -+ -+ .has_uart0 = 1, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [4] = { -+ .used = 1, -+ .phy_id = 0xff, -+ .bypass_link = 1, -+ .force_speed = 1000, -+ .force_duplex_full = 1, -+ .name = "RGMII", -+ }, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 24, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 25, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 12, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "service", -+ .gpio = 10, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ }, -+ -+ .devs = nb6_devices, -+ .num_devs = ARRAY_SIZE(nb6_devices), -+}; -+#endif -+ - /* - * known 6368 boards - */ -@@ -2864,6 +2964,10 @@ static const struct board_info __initcon - &board_DVAG3810BN, - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+ &board_nb6, -+#endif -+ - #ifdef CONFIG_BCM63XX_CPU_6368 - &board_96368mvwg, - &board_96368mvngr, -@@ -2931,6 +3035,11 @@ static void __init boardid_fixup(u8 *boo - } - } - -+ if (BCMCPU_IS_6362() && (!strncmp(board_name, "NB6-", sizeof("NB6-") - 1))) { -+ board_name[sizeof("NB6") - 1] = '\0'; -+ return ; -+ } -+ - /* check if bcm_tag is at 64k offset */ - if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* else try 128k */ diff --git a/target/linux/brcm63xx/patches-3.9/529-board_fast2604.patch b/target/linux/brcm63xx/patches-3.9/529-board_fast2604.patch deleted file mode 100644 index c8535bdde8..0000000000 --- a/target/linux/brcm63xx/patches-3.9/529-board_fast2604.patch +++ /dev/null @@ -1,68 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1066,6 +1066,57 @@ static struct board_info __initdata boar - .has_ehci0 = 1, - }; - -+static struct board_info __initdata board_FAST2604 = { -+ .name = "F@ST2604", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "F@ST2604:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "F@ST2604:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "F@ST2604:red:inet", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "F@ST2604:green:wps", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_rta1025w_16 = { - .name = "RTA1025W_16", - .expected_cpu_id = 0x6348, -@@ -2932,6 +2983,7 @@ static const struct board_info __initcon - &board_96348gw_10, - &board_96348gw_11, - &board_FAST2404, -+ &board_FAST2604, - &board_DV201AMR, - &board_96348gw_a, - &board_rta1025w_16, diff --git a/target/linux/brcm63xx/patches-3.9/530-board_963281T_TEF.patch b/target/linux/brcm63xx/patches-3.9/530-board_963281T_TEF.patch deleted file mode 100644 index 46a86582bc..0000000000 --- a/target/linux/brcm63xx/patches-3.9/530-board_963281T_TEF.patch +++ /dev/null @@ -1,136 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -250,6 +250,125 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_963281T_TEF = { -+ .name = "963281T_TEF", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "963281T_TEF:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "963281T_TEF:red:power", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:inet", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:inet", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:ppp", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:3g", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:3g", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:wlan", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:wlan", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:eth", -+ .gpio = 31, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:eth", -+ .gpio = 20, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 24, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_dsl_274xb_f1 = { - .name = "AW4339U", - .expected_cpu_id = 0x6328, -@@ -2964,6 +3083,7 @@ static const struct board_info __initcon - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, - &board_963281TAN, -+ &board_963281T_TEF, - &board_dsl_274xb_f1, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 diff --git a/target/linux/brcm63xx/patches-3.9/531-board_96328A-1441N1.patch b/target/linux/brcm63xx/patches-3.9/531-board_96328A-1441N1.patch deleted file mode 100644 index b86e4edf14..0000000000 --- a/target/linux/brcm63xx/patches-3.9/531-board_96328A-1441N1.patch +++ /dev/null @@ -1,89 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -180,6 +180,78 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96328A_1441N1 = { -+ .name = "96328A-1441N1", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96328A-1441N1:green:power", -+ .gpio = 8, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96328A-1441N1:red:power", -+ .gpio = 4, -+ }, -+ { -+ .name = "96328A-1441N1:green:inet", -+ .gpio = 7, -+ }, -+ { -+ .name = "96328A-1441N1:red:inet", -+ .gpio = 1, -+ }, -+ { -+ .name = "96328A-1441N1:green:dsl", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_963281TAN = { - .name = "963281TAN", - .expected_cpu_id = 0x6328, -@@ -3082,6 +3154,7 @@ static const struct board_info __initcon - #endif - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_96328A_1441N1, - &board_963281TAN, - &board_963281T_TEF, - &board_dsl_274xb_f1, diff --git a/target/linux/brcm63xx/patches-3.9/532-board_96328a-1241N.patch b/target/linux/brcm63xx/patches-3.9/532-board_96328a-1241N.patch deleted file mode 100644 index 0ef58e24fa..0000000000 --- a/target/linux/brcm63xx/patches-3.9/532-board_96328a-1241N.patch +++ /dev/null @@ -1,83 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -180,6 +180,72 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96328A_1241N = { -+ .name = "96328A-1241N", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96328A-1241N:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96328A-1241N:red:alarm", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96328A-1241N:green:inet", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96328A_1441N1 = { - .name = "96328A-1441N1", - .expected_cpu_id = 0x6328, -@@ -3154,6 +3220,7 @@ static const struct board_info __initcon - #endif - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_96328A_1241N, - &board_96328A_1441N1, - &board_963281TAN, - &board_963281T_TEF, diff --git a/target/linux/brcm63xx/patches-3.9/533-board_rta770bw.patch b/target/linux/brcm63xx/patches-3.9/533-board_rta770bw.patch deleted file mode 100644 index 9fc31cc495..0000000000 --- a/target/linux/brcm63xx/patches-3.9/533-board_rta770bw.patch +++ /dev/null @@ -1,66 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -785,6 +785,55 @@ static struct board_info __initdata boar - - .has_uart0 = 1, - }; -+ -+static struct board_info __initdata board_rta770bw = { -+ .name = "RTA770BW", -+ .expected_cpu_id = 0x6345, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA770BW:green:usb", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770BW:green:adsl", -+ .gpio = 8, -+ }, -+ { -+ .name = "RTA770BW:green:diag", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770BW:green:wlan", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 13, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -3234,6 +3283,7 @@ static const struct board_info __initcon - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, -+ &board_rta770bw, - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.9/534-board_hw556.patch b/target/linux/brcm63xx/patches-3.9/534-board_hw556.patch deleted file mode 100644 index c66caf7fe3..0000000000 --- a/target/linux/brcm63xx/patches-3.9/534-board_hw556.patch +++ /dev/null @@ -1,561 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2891,6 +2891,488 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_HW556 = { -+ .name = "HW556", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .caldata_offset = 0xe00000, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_A = { -+ .name = "HW556_A", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_RALINK, -+ .caldata_offset = 0xeffe00, -+ .slot = 1, -+ .eeprom = "rt2x00.eeprom", -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:green:lan1", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan2", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:message", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan1", -+ .gpio = 13, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan2", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan3", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan3", -+ .gpio = 26, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan4", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan4", -+ .gpio = 28, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_B = { -+ .name = "HW556_B", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0xf7e000, -+ .slot = 1, -+ .endian_check = 1, -+ .led_pin = 2, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:green:lan1", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan1", -+ .gpio = 13, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan2", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan2", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan3", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan3", -+ .gpio = 26, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan4", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan4", -+ .gpio = 28, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_C = { -+ .name = "HW556_C", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0xefe000, -+ .slot = 1, -+ .endian_check = 1, -+ .led_pin = 2, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:green:lan1", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan1", -+ .gpio = 13, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan2", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan2", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan3", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan3", -+ .gpio = 26, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:green:lan4", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:lan4", -+ .gpio = 28, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - /* T-Home Speedport W 303V Typ B */ - static struct board_info __initdata board_spw303v = { - .name = "96358-502V", -@@ -3322,6 +3804,10 @@ static const struct board_info __initcon - &board_nb4_fxc_r2, - &board_ct6373_1, - &board_HW553, -+ &board_HW556, -+ &board_HW556_A, -+ &board_HW556_B, -+ &board_HW556_C, - &board_spw303v, - &board_DVAG3810BN, - #endif -@@ -3387,13 +3873,37 @@ static void __init boardid_fixup(u8 *boo - struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); - char *board_name = (char *)bcm63xx_nvram_get_name(); - -- if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) { -- u8 *p = boot_addr + NB4_PID_OFFSET; -- -- /* Extract nb4 PID */ -- if (!memcmp(p, "NB4-", 4)) { -- memcpy(board_name, p, sizeof("NB4-XXX-rX")); -- return; -+ if (BCMCPU_IS_6358()) { -+ if (!strcmp(board_name, "96358VW")) { -+ u8 *p = boot_addr + NB4_PID_OFFSET; -+ -+ /* Extract nb4 PID */ -+ if (!memcmp(p, "NB4-", 4)) { -+ memcpy(board_name, p, sizeof("NB4-XXX-rX")); -+ return; -+ } -+ } else if (!strcmp(board_name, "HW556")) { -+ /* -+ * HW556 has different wlan caldatas depending on -+ * hardware version. -+ * Detect hardware version and change board id -+ */ -+ u8 cal_data_ath9k[4] = { 0xa5, 0x5a, 0, 0 }; -+ u8 cal_data_rt3062[4] = { 0x62, 0x30, 1, 0 }; -+ -+ if (!memcmp(boot_addr + 0xeffe00, -+ &cal_data_rt3062, 4)) { -+ /* Ralink 0xeffe00 */ -+ memcpy(board_name, "HW556_A", 7); -+ } else if (!memcmp(boot_addr + 0xf7e000, -+ &cal_data_ath9k, 4)) { -+ /* Atheros 0xf7e000 */ -+ memcpy(board_name, "HW556_B", 7); -+ } else if (!memcmp(boot_addr + 0xefe000, -+ &cal_data_ath9k, 4)) { -+ /* Atheros 0xefe000 */ -+ memcpy(board_name, "HW556_C", 7); -+ } - } - } - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -70,6 +70,11 @@ static int bcm63xx_parse_cfe_partitions( - BCM63XX_CFE_BLOCK_SIZE); - - cfelen = cfe_erasesize; -+ -+ /* Fix HW556 MX29LV128DB */ -+ if (!strncmp(bcm63xx_nvram_get_name(), "HW556", 5)) -+ cfelen = 0x20000; -+ - nvramlen = bcm63xx_nvram_get_psi_size(); - nvramlen = roundup(nvramlen, cfe_erasesize); - nvramaddr = master->size - nvramlen; diff --git a/target/linux/brcm63xx/patches-3.9/535-board_rta770w.patch b/target/linux/brcm63xx/patches-3.9/535-board_rta770w.patch deleted file mode 100644 index 3933d00b5c..0000000000 --- a/target/linux/brcm63xx/patches-3.9/535-board_rta770w.patch +++ /dev/null @@ -1,71 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -773,6 +773,60 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+// Actually this board is the very same as the rta770bw, -+// where the additional 'b' within the name just -+// just indicates 'Annex B'. The ADSL Modem itself is able -+// to handle both Annex A as well as Annex B - -+// the loaded firmware makes the only difference -+static struct board_info __initdata board_rta770w = { -+ .name = "RTA770W", -+ .expected_cpu_id = 0x6345, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA770W:green:usb", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770W:green:adsl", -+ .gpio = 8, -+ }, -+ { -+ .name = "RTA770W:green:diag", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770W:green:wlan", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 13, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -3766,6 +3820,7 @@ static const struct board_info __initcon - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, - &board_rta770bw, -+ &board_rta770w, - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.9/550-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-3.9/550-alice_gate2_leds.patch deleted file mode 100644 index 4578a1d514..0000000000 --- a/target/linux/brcm63xx/patches-3.9/550-alice_gate2_leds.patch +++ /dev/null @@ -1,102 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2091,6 +2091,99 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "AGPF-S0:red:power", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "AGPF-S0:red:service", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:service", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:adsl", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:adsl", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:wifi", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:wifi", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:internet", -+ .gpio = 25, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:internet", -+ .gpio = 24, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:usr1", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:usr1", -+ .gpio = 26, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:usr2", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:usr2", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 37, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_DWVS0 = { diff --git a/target/linux/brcm63xx/patches-3.9/551-96348gw_a_leds.patch b/target/linux/brcm63xx/patches-3.9/551-96348gw_a_leds.patch deleted file mode 100644 index 67246d2d60..0000000000 --- a/target/linux/brcm63xx/patches-3.9/551-96348gw_a_leds.patch +++ /dev/null @@ -1,22 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1536,6 +1536,19 @@ static struct board_info __initdata boar - }, - - .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348GW-A::adsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348GW-A::usb", -+ .gpio = 0, -+ .active_low = 1, -+ } -+ }, - }; - - static struct board_info __initdata board_96348_D4PW = { diff --git a/target/linux/brcm63xx/patches-3.9/552-board_96348gw-10_reset_button.patch b/target/linux/brcm63xx/patches-3.9/552-board_96348gw-10_reset_button.patch deleted file mode 100644 index 1562631b2b..0000000000 --- a/target/linux/brcm63xx/patches-3.9/552-board_96348gw-10_reset_button.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -996,6 +996,17 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 6, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_96348gw_11 = { diff --git a/target/linux/brcm63xx/patches-3.9/553-boards_probe_switch.patch b/target/linux/brcm63xx/patches-3.9/553-boards_probe_switch.patch deleted file mode 100644 index 0d28160279..0000000000 --- a/target/linux/brcm63xx/patches-3.9/553-boards_probe_switch.patch +++ /dev/null @@ -1,119 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -624,6 +624,8 @@ static struct board_info __initdata boar - .has_uart0 = 1, - .has_enet0 = 1, - .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -667,6 +669,8 @@ static struct board_info __initdata boar - .has_uart0 = 1, - .has_enet0 = 1, - .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -952,6 +956,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1024,6 +1030,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1253,6 +1261,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1428,6 +1438,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1502,6 +1514,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1523,6 +1537,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1542,6 +1558,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1917,6 +1935,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1969,6 +1989,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -2109,6 +2131,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -2226,6 +2250,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.9/554-board_DWVS0_leds_buttons.patch b/target/linux/brcm63xx/patches-3.9/554-board_DWVS0_leds_buttons.patch deleted file mode 100644 index 32a431504f..0000000000 --- a/target/linux/brcm63xx/patches-3.9/554-board_DWVS0_leds_buttons.patch +++ /dev/null @@ -1,97 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2258,6 +2258,94 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "DWV-S0:red:power", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "DWV-S0:red:internet", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:internet", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:ADSL", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:red:ADSL", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:red:wifi", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:VoIP", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:red:VoIP", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:red:ethernet", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:ethernet", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:red:USB", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ { -+ .name = "DWV-S0:green:USB", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 37, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - /* D-Link DSL-274xB revison C2/C3 */ diff --git a/target/linux/brcm63xx/patches-3.9/800-wl_exports.patch b/target/linux/brcm63xx/patches-3.9/800-wl_exports.patch deleted file mode 100644 index 3b3b1ea6ee..0000000000 --- a/target/linux/brcm63xx/patches-3.9/800-wl_exports.patch +++ /dev/null @@ -1,34 +0,0 @@ ---- a/arch/mips/bcm63xx/nvram.c -+++ b/arch/mips/bcm63xx/nvram.c -@@ -41,6 +41,13 @@ struct bcm963xx_nvram { - static struct bcm963xx_nvram nvram; - static int mac_addr_used; - -+/* -+ * Required export for WL -+ */ -+#define NVRAM_SPACE 0x8000 -+char nvram_buf[NVRAM_SPACE]; -+EXPORT_SYMBOL(nvram_buf); -+ - void __init bcm63xx_nvram_init(void *addr) - { - unsigned int check_len; -@@ -49,6 +56,7 @@ void __init bcm63xx_nvram_init(void *add - - /* extract nvram data */ - memcpy(&nvram, addr, sizeof(nvram)); -+ memcpy(&nvram_buf, addr, NVRAM_SPACE); - - /* check checksum before using data */ - if (nvram.version <= 4) { ---- a/arch/mips/mm/cache.c -+++ b/arch/mips/mm/cache.c -@@ -58,6 +58,7 @@ void (*_dma_cache_wback)(unsigned long s - void (*_dma_cache_inv)(unsigned long start, unsigned long size); - - EXPORT_SYMBOL(_dma_cache_wback_inv); -+EXPORT_SYMBOL(_dma_cache_inv); - - #endif /* CONFIG_DMA_NONCOHERENT */ - diff --git a/target/linux/brcm63xx/patches-3.9/801-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-3.9/801-ssb_export_fallback_sprom.patch deleted file mode 100644 index 58caf68a05..0000000000 --- a/target/linux/brcm63xx/patches-3.9/801-ssb_export_fallback_sprom.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -14,6 +14,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -4113,7 +4114,7 @@ static const struct board_info __initcon - * bcm4318 WLAN work - */ - #ifdef CONFIG_SSB_PCIHOST --static struct ssb_sprom bcm63xx_sprom = { -+struct ssb_sprom bcm63xx_sprom = { - .revision = 0x02, - .board_rev = 0x17, - .country_code = 0x0, -@@ -4133,6 +4134,7 @@ static struct ssb_sprom bcm63xx_sprom = - .boardflags_lo = 0x2848, - .boardflags_hi = 0x0000, - }; -+EXPORT_SYMBOL(bcm63xx_sprom); - - int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) - { diff --git a/target/linux/brcm63xx/patches-3.9/802-rtl8367r_fix_RGMII_support.patch b/target/linux/brcm63xx/patches-3.9/802-rtl8367r_fix_RGMII_support.patch deleted file mode 100644 index 9037d8954a..0000000000 --- a/target/linux/brcm63xx/patches-3.9/802-rtl8367r_fix_RGMII_support.patch +++ /dev/null @@ -1,30 +0,0 @@ -From e3208e6087642b95a5bab3101fc9c6e34892c861 Mon Sep 17 00:00:00 2001 -From: Miguel GAIO -Date: Fri, 6 Jul 2012 14:12:33 +0200 -Subject: [PATCH 6/8] * [rtl8367r] Fix RGMII support - ---- - drivers/net/phy/rtl8367.c | 5 +++++ - 1 files changed, 5 insertions(+), 0 deletions(-) - ---- a/drivers/net/phy/rtl8367.c -+++ b/drivers/net/phy/rtl8367.c -@@ -146,6 +146,10 @@ - #define RTL8367_EXT_RGMXF_TXDELAY_MASK 1 - #define RTL8367_EXT_RGMXF_RXDELAY_MASK 0x7 - -+#define RTL8367_PHY_AD_REG 0x130f -+#define RTL8370_PHY_AD_DUMMY_1_OFFSET 5 -+#define RTL8370_PHY_AD_DUMMY_1_MASK 0xe0 -+ - #define RTL8367_DI_FORCE_REG(_x) (0x1310 + (_x)) - #define RTL8367_DI_FORCE_MODE BIT(12) - #define RTL8367_DI_FORCE_NWAY BIT(7) -@@ -894,6 +898,7 @@ static int rtl8367_extif_set_mode(struct - case RTL8367_EXTIF_MODE_RGMII_33V: - REG_WR(smi, RTL8367_CHIP_DEBUG0_REG, 0x0367); - REG_WR(smi, RTL8367_CHIP_DEBUG1_REG, 0x7777); -+ REG_RMW(smi, RTL8367_PHY_AD_REG, BIT(5), 0); - break; - - case RTL8367_EXTIF_MODE_TMII_MAC: -- cgit v1.2.3