From 43c7132bf8e7dc0756b527f985a1ac6056007f62 Mon Sep 17 00:00:00 2001
From: Tomasz Maciej Nowak <tmn505@gmail.com>
Date: Wed, 24 Aug 2022 18:05:58 +0200
Subject: ath79: add support for MikroTik RouterBOARD 911 Lite2/Lite5
Forward-port from ar71xx target the board introduced in commit
eb9e3651dd1a (" ar71xx: add support for the MikroTik RB911-2Hn/5Hn
boards"). Citing:
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hn
https://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).[1]
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.[2]
End of citation.
Follow intallation instruction from that commit message, using
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-initramfs-kernel.bin
and
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-squashfs-sysupgrade.bin
images found in ath79/mikrotik directory. Be advised that the board
accepts 10-30 V on PoE input.
Known issues
Compared to ar71xx target image, there is still small leak of current to
user LED, which makes it lit, although weaker, even if brightness is set
to 0. The cause of that is still unknown.
1. https://github.com/openwrt/openwrt/pull/3652
2. RB911-5HnD should work with this commit or with [1], depending on
what flash topology was used.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
---
.../ath79/mikrotik/base-files/etc/board.d/01_leds | 19 ++++++++++---------
.../ath79/mikrotik/base-files/etc/board.d/02_network | 2 ++
.../base-files/etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
3 files changed, 13 insertions(+), 9 deletions(-)
(limited to 'target/linux/ath79/mikrotik')
diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/01_leds b/target/linux/ath79/mikrotik/base-files/etc/board.d/01_leds
index 76b91a54a5..4c1b98fff2 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/01_leds
@@ -6,6 +6,16 @@ board_config_update
board=$(board_name)
case "$board" in
+mikrotik,routerboard-911-lite|\
+mikrotik,routerboard-lhg-5nd)
+ ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "rssilow" "rssilow" "green:rssilow" "wlan0" "1" "100"
+ ucidef_set_led_rssi "rssimediumlow" "rssimediumlow" "green:rssimediumlow" "wlan0" "20" "100"
+ ucidef_set_led_rssi "rssimedium" "rssimedium" "green:rssimedium" "wlan0" "40" "100"
+ ucidef_set_led_rssi "rssimediumhigh" "rssimediumhigh" "green:rssimediumhigh" "wlan0" "60" "100"
+ ucidef_set_led_rssi "rssihigh" "rssihigh" "green:rssihigh" "wlan0" "80" "100"
+ ;;
mikrotik,routerboard-951ui-2nd|\
mikrotik,routerboard-952ui-5ac2nd)
ucidef_set_led_netdev "port1" "port1" "green:port1" "eth1"
@@ -19,15 +29,6 @@ mikrotik,routerboard-mapl-2nd|\
mikrotik,routerboard-wap-2nd)
ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0"
;;
-mikrotik,routerboard-lhg-5nd)
- ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0"
- ucidef_set_rssimon "wlan0" "200000" "1"
- ucidef_set_led_rssi "rssilow" "rssilow" "green:rssilow" "wlan0" "1" "100"
- ucidef_set_led_rssi "rssimediumlow" "rssimediumlow" "green:rssimediumlow" "wlan0" "20" "100"
- ucidef_set_led_rssi "rssimedium" "rssimedium" "green:rssimedium" "wlan0" "40" "100"
- ucidef_set_led_rssi "rssimediumhigh" "rssimediumhigh" "green:rssimediumhigh" "wlan0" "60" "100"
- ucidef_set_led_rssi "rssihigh" "rssihigh" "green:rssihigh" "wlan0" "80" "100"
- ;;
mikrotik,routerboard-map-2nd)
ucidef_set_led_netdev "eth_1" "eth_1" "green:eth_1" "eth1"
ucidef_set_led_switch "eth_2" "eth_2" "green:eth_2" "switch0" "0x4"
diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
index 5646d8cf68..da63347c3c 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch1" \
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
;;
+ mikrotik,routerboard-911-lite|\
mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-lhg-5nd|\
@@ -52,6 +53,7 @@ ath79_setup_macs()
local mac_base="$(cat /sys/firmware/mikrotik/hard_config/mac_base)"
case "$board" in
+ mikrotik,routerboard-911-lite|\
mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-lhg-5nd|\
diff --git a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index aa5354bfdb..e0bf1e47ef 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -23,6 +23,7 @@ board=$(board_name)
case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
+ mikrotik,routerboard-911-lite|\
mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-lhg-5nd|\
--
cgit v1.2.3