From e8cbdbbe97d55b77062a3d80f42c87cb761e9729 Mon Sep 17 00:00:00 2001 From: Mauri Sandberg Date: Mon, 7 Sep 2020 22:04:26 +0300 Subject: ath79: Add support for Buffalo WZR-HP-G300NH This device is a wireless router working on 2.4GHz band based on Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103 wireless chip and Realtek RTL8366RB/S switches. Due to two different switches being used also two different devices are provided. Specification: - 400 MHz CPU - 64 MB of RAM - 32 MB of FLASH (NOR) - 3x3:2 2.4 GHz 802.11bgn - 5x 10/100/1000 Mbps Ethernet - 4x LED, 3x button, On/Off slider, Auto/On/Off slider - 1x USB 2.0 - bare UART header place on PCB Flash instruction: - NOTE: Pay attention to the switch variant and choose the image to flash accordingly. (dmesg / kernel logs can tell it) - Methods for flashing - Apply factory image in OEM firmware web-gui. - Sysupgrade on top of existing OpenWRT image - U-Boot TFPT recovery for both stock or OpenWRT images: The device U-boot contains a TFTP server that by default has an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot there is a time window, during which the device allows an image to be uploaded from a client with address 192.168.11.2. The image will be written on flash automatically. 1) Have a computer with static IP address 192.168.11.2 and the router device switched off. 2) Connect the LAN port next to the WAN port in the device and the computer using a network switch. 3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A arp -s 192.168.11.1 02:AA:BB:CC:DD:1A 4) Initiate an upload using TFTP image variant curl -T tftp://192.168.11.1 5) Switch on the device. The image will be uploaded subsequently. You can keep an eye on the diag light on the device, it should keep on blinking for a while indicating the writing of the image. General notes: - In the stock firmware the MAC address is the same among all interfaces so it is left here that way too. Recovery: - TFTP method - U-boot serial console Differences to ar71xx platform - This device is split in two different targets now due to hardware being a bit different under the hood. Dynamic solution within the same image is left for later time. - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device cover, were the wrong way around and were renamed qos_on -> movie_off, qos_off -> movie_on. Associated key codes remained the same they were. The device tree source code is mostly based on musashino's work Signed-off-by: Mauri Sandberg (cherry picked from commit bc356de2850f14629cb1301be719772fa1212e72) --- target/linux/ath79/image/generic.mk | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) (limited to 'target/linux/ath79/image') diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 6eda757445..d93ebbaeba 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -453,6 +453,29 @@ define Device/buffalo_wzr-hp-ag300h endef TARGET_DEVICES += buffalo_wzr-hp-ag300h +define Device/buffalo_wzr-hp-g300nh + $(Device/buffalo_common) + SOC := ar9132 + BUFFALO_PRODUCT := WZR-HP-G300NH + BUFFALO_HWVER := 1 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-gpio-nxp-74hc153 + BLOCKSIZE := 128k + IMAGE_SIZE := 32128k + SUPPORTED_DEVICES += wzr-hp-g300nh +endef + +define Device/buffalo_wzr-hp-g300nh-rb + $(Device/buffalo_wzr-hp-g300nh) + DEVICE_MODEL := WZR-HP-G300NH (RTL8366RB switch) +endef +TARGET_DEVICES += buffalo_wzr-hp-g300nh-rb + +define Device/buffalo_wzr-hp-g300nh-s + $(Device/buffalo_wzr-hp-g300nh) + DEVICE_MODEL := WZR-HP-G300NH (RTL8366S switch) +endef +TARGET_DEVICES += buffalo_wzr-hp-g300nh-s + define Device/buffalo_wzr-hp-g302h-a1a0 $(Device/buffalo_common) SOC := ar7242 -- cgit v1.2.3