From eb9ba2b91e0f0c2d0b072b3fea3ea2a8b50af5fc Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Sat, 8 Oct 2016 01:17:04 +0200 Subject: ar71xx: add support for YunCore CPE870 YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz --- target/linux/ar71xx/base-files/etc/board.d/01_leds | 9 +++++++++ target/linux/ar71xx/base-files/etc/diag.sh | 1 + 2 files changed, 10 insertions(+) (limited to 'target/linux/ar71xx/base-files/etc') diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index c348b4fbda..2cf72d61d3 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -58,6 +58,7 @@ ap147-010) ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "ap147:green:wlan-2g" "phy0tpt" ;; ap90q|\ +cpe870|\ dr531) ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" @@ -66,6 +67,14 @@ dr531) ap90q) ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" ;; + cpe870) + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSILOW" "$board:green:link1" "wlan0" "1" "100" "0" "13" + ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "$board:green:link2" "wlan0" "26" "100" "-25" "13" + ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$board:green:link3" "wlan0" "51" "100" "-50" "13" + ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$board:green:link4" "wlan0" "76" "100" "-75" "13" + ;; esac ;; bhr-4grv2) diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 0ef5a52a05..e619749609 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -48,6 +48,7 @@ get_status_led() { status_led="$board:green:power" ;; ap90q|\ + cpe870|\ gl-inet) status_led="$board:green:lan" ;; -- cgit v1.2.3