From f5f01bcacd7838889cb83defca94af34e64a9141 Mon Sep 17 00:00:00 2001 From: Michael Pratt Date: Mon, 11 Jan 2021 03:34:33 -0500 Subject: ath79: use internal switch for EAP300 v2 Have the port use GMAC1 with internal switch which fixes the issue of the ethernet LED not functioning The LED is triggered by the internal switch, not a GPIO. The GPIO for the ethernet LED was added in ath79 as it was defined in the ar71xx target but it was not functioning in ath79 for a previously unknown reason. It is unknown why that GPIO was defined as an LED in ar71xx. Signed-off-by: Michael Pratt [drop unrelated changes: model property and SPI max frequency] Signed-off-by: Adrian Schmutzler --- target/linux/ath79/dts/ar9341_engenius_eap300-v2.dts | 20 +------------------- .../ath79/generic/base-files/etc/board.d/01_leds | 1 - .../ath79/generic/base-files/etc/board.d/02_network | 5 ++++- 3 files changed, 5 insertions(+), 21 deletions(-) diff --git a/target/linux/ath79/dts/ar9341_engenius_eap300-v2.dts b/target/linux/ath79/dts/ar9341_engenius_eap300-v2.dts index 7aa89a4cce..7900557775 100644 --- a/target/linux/ath79/dts/ar9341_engenius_eap300-v2.dts +++ b/target/linux/ath79/dts/ar9341_engenius_eap300-v2.dts @@ -43,11 +43,6 @@ gpios = <&gpio 17 GPIO_ACTIVE_LOW>; linux,default-trigger = "phy0tpt"; }; - - lan { - label = "blue:lan"; - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; }; virtual_flash { @@ -145,21 +140,8 @@ }; }; -ð0 { - status = "okay"; - - mtd-mac-address = <&art 0x0>; - - phy-handle = <&swphy0>; - - gmac-config { - device = <&gmac>; - switch-phy-swap = <1>; - }; -}; - ð1 { - compatible = "syscon", "simple-mfd"; + mtd-mac-address = <&art 0x0>; }; &wmac { diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 169df8b285..f7d8ec0f85 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -156,7 +156,6 @@ telco,t1) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" ;; comfast,cf-wr752ac-v1|\ -engenius,eap300-v2|\ enterasys,ws-ap3705i|\ openmesh,mr900-v1|\ openmesh,mr900-v2|\ diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index ab00d798b1..4380a380fc 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -33,7 +33,6 @@ ath79_setup_interfaces() dlink,dap-3320-a1|\ dlink,dir-505|\ engenius,eap1200h|\ - engenius,eap300-v2|\ engenius,eap600|\ engenius,ecb1200|\ engenius,ecb1750|\ @@ -237,6 +236,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:wan" "2:lan:3" "3:lan:2" ;; + engenius,eap300-v2) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan" + ;; engenius,ens202ext-v1) ucidef_set_interface_lan "eth1" ucidef_add_switch "switch0" \ -- cgit v1.2.3