aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ipq807x: add support for Buffalo WXR-5950AX12INAGAKI Hiroshi2023-02-126-0/+454
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq807x: merge duplicate network configurations in 02_networkINAGAKI Hiroshi2023-02-121-4/+2
| | | | | | | | Merge network configurations in 02_network of Dynalink DL-WRX36 and Xiaomi AX9000. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq807x: enable regulator-fixed driverINAGAKI Hiroshi2023-02-121-0/+1
| | | | | | | | Enable regulator-fixed to define the regulator of USB vbus on Buffalo WXR-5950AX12. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: add support for APRESIA ApresiaLightGS120GT-SSINAGAKI Hiroshi2023-02-133-0/+556
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | APRESIA ApresiaLightGS120GT-SS (APLGS120GTSS) is a 16 + 4 ports gigabit switch, based on RTL8382M. Specifications: - SoC : Realtek RTL8382M - RAM : DDR3 256 MiB (Nanya NT5CC256M8JQ-EK) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x16 + 4 - port 1-8 : RTL8218B - port 9-16 : RTL8382M, TP (SoC, RTL8218B) - port 17-20 : RTL8214FC, TP/SFP (Combo) - LEDs/Keys : 3x/1x - UART : through-hole on PCB - J6: 3.3V, TX, RX, GND from tri-angle marking side - 115200n8 - Power : 100-120/200-240 VAC, 50/60 Hz Max. 16 W, Avg 14 W (100 VAC) - Plug : IEC 60320-C13 Flash instruction using factory image: 1. Boot ApresiaLightGS120GT-SS normally 2. Login to WebUI and open firmware page ("ファームウェア") 3. If the device is booted from image1, set active image for next booting ("起動イメージ選択") to image2("イメージ2"), press apply ("適用") button and reboot the device to make booting from image2 4. On the WebUI, set active image to image1 5. Select the OpenWrt factory image and press update button ("更新") 6. Open reboot page ("再起動") and press reboot button ("再起動実行") Notes: - "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model number - this device has 3x GPIO-controlled LEDs on PCB, but 1x LED ("green:unused") has no hole on the case Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: add common definition of cameo based firmwareINAGAKI Hiroshi2023-02-132-10/+16
| | | | | | | | | | | | The cameo-related recipes can also be used for APRESIA ApresiaLightGS series devices. So create common definition for the devices manufactured by Cameo. And also, the model name of ApresiaLightGS120GT-SS is too long for cameo header (max: 20 bytes), so use additional variable "CAMEO_BOARD_MODEL" in Build/cameo-headers instead of DEVICE_MODEL to use the custom name. (default of CAMEO_BOARD_MODEL: DEVICE_MODEL) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: rename cameo specific names in "Build/*" definitionsINAGAKI Hiroshi2023-02-132-10/+10
| | | | | | | | This patch renames some Cameo specific definitions for image generation. The same format is also used on APRESIA ApresiaLightGS series devices, not D-Link specific. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: fix memory leak in netevent handlerJan Hoffmann2023-02-132-16/+18
| | | | | | | | | The net_event_work struct is allocated, but only freed in a single case. Move the allocation to the branch where it is actually needed, and free it after the work has been done. Fixes: 03e1d93e0779 ("realtek: add driver support for routing offload") Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* kernel: add missing optimization for page poolFelix Fietkau2023-02-132-0/+112
| | | | | | Improves performance in combination with threaded NAPI Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for ASUS RT-AX54Karl Chan2023-02-124-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX54 (AX1800S/HP,AX54HP) - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 4 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x POWER (blue, configurable) 1x LAN (blue, configurable) 1x WAN (blue, configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Karl Chan <exkc@exkc.moe>
* ath79: bump SPI frequency of Senao qca955x routersMichael Pratt2023-02-121-1/+1
| | | | | | | | All boards using this DTSI are expected to have the same 16 MB MX25L12845EMI-10G flash chip, or a larger one which can also use 40 MHz frequency. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add eth0 mac and initvals for Engenius EPG5000Michael Pratt2023-02-122-1/+9
| | | | | | | | | | | | | | | | | | Although VLANs are used, the "eth0" device by itself does not have a valid MAC, so fix that with preinit script. More initvals added by editing the driver to print switch registers, after the bootloader sets them but before openwrt changes them. The register bits needed for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by adding print lines in the switch driver ar8327.c before 'qca,ar8327-initvals' is parsed from DTS and written for example: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: convert Engenius EPG5000 radios to nvmem-cellsMichael Pratt2023-02-124-18/+23
| | | | | | | | | | | Use nvmem kernel subsystem to pull radio calibration data with the devicetree instead of userspace scripts. Existing blocks for caldata_extract are reordered alphabetically. MAC address is set using the hotplug script. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius ESR1200Michael Pratt2023-02-125-0/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ESR900 Engenius ESR1200 is an indoor wireless router with a gigabit ethernet switch, dual-band wireless, internal antenna plates, and a USB 2.0 port **Specification:** - QCA9557 SOC 2.4 GHz, 2x2 - QCA9882 WLAN PCIe mini card, 5 GHz, 2x2 - QCA8337N SW 4 ports LAN, 1 port WAN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM - UART at J1 populated, RX grounded - 6 internal antenna plates (omni-directional) - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset) **MAC addresses:** Base MAC address labeled as "MAC ADDRESS" MAC "wanaddr" is not similar to "ethaddr" eth0 *:c8 MAC u-boot-env ethaddr phy0 *:c8 MAC u-boot-env ethaddr phy1 *:c9 --- u-boot-env ethaddr +1 WAN *:66:44 u-boot-env wanaddr **Serial Access:** RX on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin **Installation:** Method 1: Firmware upgrade page OEM webpage at 192.168.0.1 username and password "admin" Navigate to Settings (gear icon) --> Tools --> Firmware select the factory.bin image confirm and wait 3 minutes Method 2: TFTP recovery Follow TFTP instructions using initramfs.bin use sysupgrade.bin to flash using openwrt web interface **Return to OEM:** MTD partitions should be backed up before flashing using TFTP to boot openwrt without overwriting flash Alternatively, it is possible to edit OEM firmware images to flash MTD partitions in openwrt to restore OEM firmware by removing the OEM header and writing the rest to "firmware" **TFTP recovery:** Requires serial console, reset button does nothing at boot rename initramfs.bin to 'uImageESR1200' make available on TFTP server at 192.168.99.8 power board, interrupt boot by pressing '4' rapidly execute tftpboot and bootm **Note on ETH switch registers** Registers must be written to the ethernet switch in order to set up the switch's MAC interface. U-boot can write the registers on it's own which is needed, for example, in a TFTP transfer. The register bits from OEM for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by adding print lines in the switch driver ar8327.c before 'qca,ar8327-initvals' is parsed from DTS and written. for example: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius ESR1750Michael Pratt2023-02-125-0/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ESR1750 Engenius ESR1750 is an indoor wireless router with a gigabit ethernet switch, dual-band wireless, internal antenna plates, and a USB 2.0 port **Specification:** - QCA9558 SOC 2.4 GHz, 3x3 - QCA9880 WLAN PCIe mini card, 5 GHz, 3x3 - QCA8337N SW 4 ports LAN, 1 port WAN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM - UART at J1 populated, RX grounded - 6 internal antenna plates (omni-directional) - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset) **MAC addresses:** Base MAC address labeled as "MAC ADDRESS" MAC "wanaddr" is similar to "ethaddr" eth0 *:58 MAC u-boot-env ethaddr phy0 *:58 MAC u-boot-env ethaddr phy1 *:59 --- u-boot-env ethaddr +1 WAN *:10:58 u-boot-env wanaddr **Serial Access:** RX on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin **Installation:** Method 1: Firmware upgrade page NOTE: ESR1750 might require the factory.bin for ESR1200 instead, OEM provides 1 image for both. OEM webpage at 192.168.0.1 username and password "admin" Navigate to Settings (gear icon) --> Tools --> Firmware select the factory.bin image confirm and wait 3 minutes Method 2: TFTP recovery Follow TFTP instructions using initramfs.bin use sysupgrade.bin to flash using openwrt web interface **Return to OEM:** MTD partitions should be backed up before flashing using TFTP to boot openwrt without overwriting flash Alternatively, it is possible to edit OEM firmware images to flash MTD partitions in openwrt to restore OEM firmware by removing the OEM header and writing the rest to "firmware" **TFTP recovery:** Requires serial console, reset button does nothing at boot rename initramfs.bin to 'uImageESR1200' make available on TFTP server at 192.168.99.8 power board, interrupt boot by pressing '4' rapidly execute tftpboot and bootm **Note on ETH switch registers** Registers must be written to the ethernet switch in order to set up the switch's MAC interface. U-boot can write the registers on it's own which is needed, for example, in a TFTP transfer. The register bits from OEM for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by adding print lines in the switch driver ar8327.c before 'qca,ar8327-initvals' is parsed from DTS and written. for example: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius ESR900Michael Pratt2023-02-125-1/+108
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ESR900 Engenius ESR900 is an indoor wireless router with a gigabit ethernet switch, dual-band wireless, internal antenna plates, and a USB 2.0 port **Specification:** - QCA9558 SOC 2.4 GHz, 3x3 - AR9580 WLAN PCIe on board, 5 GHz, 3x3 - AR8327N SW 4 ports LAN, 1 port WAN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM - UART at J1 populated, RX grounded - 6 internal antenna plates (omni-directional) - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset) **MAC addresses:** Base MAC address labeled as "MAC ADDRESS" MAC "wanaddr" is not similar to "ethaddr" eth0 *:06 MAC u-boot-env ethaddr phy0 *:06 MAC u-boot-env ethaddr phy1 *:07 --- u-boot-env ethaddr +1 WAN *:6E:81 u-boot-env wanaddr **Serial Access:** RX on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin **Installation:** Method 1: Firmware upgrade page OEM webpage at 192.168.0.1 username and password "admin" Navigate to Settings (gear icon) --> Tools --> Firmware select the factory.bin image confirm and wait 3 minutes Method 2: TFTP recovery Follow TFTP instructions using initramfs.bin use sysupgrade.bin to flash using openwrt web interface **Return to OEM:** MTD partitions should be backed up before flashing using TFTP to boot openwrt without overwriting flash Alternatively, it is possible to edit OEM firmware images to flash MTD partitions in openwrt to restore OEM firmware by removing the OEM header and writing the rest to "firmware" **TFTP recovery:** Requires serial console, reset button does nothing at boot rename initramfs.bin to 'uImageESR900' make available on TFTP server at 192.168.99.8 power board, interrupt boot by pressing '4' rapidly execute tftpboot and bootm **Note on ETH switch registers** Registers must be written to the ethernet switch in order to set up the switch's MAC interface. U-boot can write the registers on it's own which is needed, for example, in a TFTP transfer. The register bits from OEM for the AR8327 switch can be read from interrupted boot (tftpboot, bootm) by adding print lines in the switch driver ar8327.c before 'qca,ar8327-initvals' is parsed from DTS and written. for example: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: split Engenius EPG5000 DTS to common DTSIMichael Pratt2023-02-122-108/+128
| | | | | | | | | | | | Split the DTS to be used with similar boards made by Senao, dual-band routers with Atheros / Qualcomm ethernet switch. Set initvals for the switch in each device's DTS. Set some common calibration nvmem-cells in DTSI. While at it, fix MTD partition node names. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* toolchain: wrapper.sh: use --rpath-linkEneas U de Queiroz2023-02-121-2/+2
| | | | | | | Use --rpath-link option instead of --rpath. The former is used only at link-time, while the latter is searched at run-time as well. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* toolchain: wrapper.sh: fix TOOLCHAIN_SYSROOT pathEneas U de Queiroz2023-02-121-1/+1
| | | | | | | | | 62c1740676 changed the location of the script from $(TOOLCHAIN_DIR)/usr to $(TOOLCHAIN_DIR), but the TOOLCHAIN_SYSROOT used in wrapper.sh was still expecting to find the script under usr/bin. Fixes: 62c1740676 toolchain: fix the sysroot mess by getting... Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* kernel: bump 5.15 to 5.15.93John Audia2023-02-1119-46/+46
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: mt7622: fix rootfs/ubi detection for Xiaomi AX6SOleg S2023-02-111-1/+0
| | | | | | | | | | | | | | | | | By specifying the flag "denx,fit" for partition "kernel", the kernel try to find rootfs in the same partition during boot. Reality is that the placement of rootfs is precisely determined by the name of another partition -"ubi". It was also found that on some device (for example devices with NAND chips), the "Denx search engine" manages to find roots at the end of partition "kernel", but such partition doesn't exist and is empty there. Fix this by removing the "denx,fit" flag from partition "kernel". With this change the original behavior of searchif rootfs in partition "ubi" is restored. Signed-off-by: Oleg S <remittor@gmail.com>
* realtek: fix dts whitespaceFelix Baumann2023-02-094-9/+9
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: fix dts whitespaceFelix Baumann2023-02-096-15/+15
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* mediatek: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kirkwood: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq807x: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq806x: fix dts whitespaceFelix Baumann2023-02-091-9/+9
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* bcm63xx: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ath79: fix dts whitespaceFelix Baumann2023-02-096-30/+30
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq40xx: fix dts whitespaceFelix Baumann2023-02-092-2/+2
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq4019: fix dts white-spaceFelix Baumann2023-02-088-438/+438
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kernel: bump 5.10 to 5.10.167John Audia2023-02-082-2/+2
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.92John Audia2023-02-082-3/+3
| | | | | | | | | | All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* lantiq: ar9/vr9: add fritz-tffs packageFelix Baumann2023-02-082-8/+12
| | | | | | | Add fritz-tffs package to AVM devices Reorder some devices packages for consistency Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* mpc85xx: p2020: kernel: enable CONFIG_BLK_DEV_NVMEŠimon Bořek2023-02-071-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot) in Turris 1.x routers and possibly NXP P2020RDB boards (these are the only currently supported p2020 devices according to docs[^1]). Proper detection, mountability and readability was proved to be working on Turris 1.1, OpenWrt 21.02 with similar configuration. Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB). Should boot from those devices be possible the driver needs to be built in. Inclusion as a module would prevent this functionality. CONFIG_BLK_DEV_NVME=y Includes NVMe driver in the kernel.[^2] CONFIG_NVME_CORE=y Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly, but included to match the form of similar functionality implementations for mvebu, x86_64 and rockchip_armv8 targets. CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary. [^1]: https://openwrt.org/docs/techref/targets/mpc85xx [^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html [^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
* mpc85xx: p2020: kernel: refresh configurationŠimon Bořek2023-02-071-5/+15
| | | | | | | 'make kernel_oldconfig CONFIG_TARGET=subtarget' applied to current master Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
* bcm47xx: revert bgmac back to the old limited max frame sizeRafał Miłecki2023-02-072-0/+66
| | | | | | | | | | | | | | Bumping max frame size has significantly affected network performance and memory usage. It was done by upstream commit that first appeared in the 5.7 release. Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a bad idea on 32 MiB devices. This commit fixes support for Linksys E1000 V2.1 which gives up after allocating ~346 such buffers running 5.15 kernel. Ref: 230c9da963aa ("bcm53xx: revert bgmac back to the old limited max frame size") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq806x: add missing enclosing reserved-memory block on C2600/AD7200Filip Matijević2023-02-071-8/+10
| | | | | | | | | | | | Most of the time when booting kernel prints a warning from mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is not functional. Fix this by moving ramopps node into reserved-memory block as described in kernel documentation. Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200") Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
* ipq807x: refresh kernel configRobert Marko2023-02-071-1/+3
| | | | | | | Refresh the ipq807x kernel config to keep it up to date and in sync with the generic one. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fix assignment of lan port numbers for Cell C RTL30VWCezary Jackiewicz2023-02-061-2/+2
| | | | | | After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ipq806x: onhub: Enable fstools_partname_fallback_scanBrian Norris2023-02-043-9/+3
| | | | | | | | | | | | | | | | | | | | When fstools is unable to parse our root=<...> arg correctly, it can fall back to scanning all block devices for a 'rootfs_data' partition. This fallback was deemed wrong (or at least, a breaking/incompatible change) for some targets, so we're forced to opt back into it with fstools_partname_fallback_scan=1. Without this, OnHub devices will use a rootfs-appended loop device for rootfs_data instead of the intended 3rd partition. While I'm at it, just move all the boot args into the 'cros-vboot' build rule, instead of using the custom bootargs-append. All cros-vboot subtargets here are using the same rootwait (to support both eMMC and USB boot) and root/partition args. Signed-off-by: Brian Norris <computersforpeace@gmail.com> [ drop unrelated comments in commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq807x: remove libwolfsslcpu-crypto dependencyRosen Penev2023-02-041-1/+1
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-0459-143/+143
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2Arınç ÜNAL2023-02-031-1/+1
| | | | | | | | The phy-mode property must be defined on the MAC instead of the PHY. Define phy-mode under gmac1 which the external phy is connected to. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* x86: add Barracuda Networks F12 interfacesTomasz Maciej Nowak2023-02-031-0/+8
| | | | | | | | | | | | | | | | | | | | Match interface numbers with printed numbers on device enclosure and assign first port as WAN interface. Notes Serial console is available through RJ-45 port with Cisco pinout baud: 19200, parity: none, flow control: none The device is setup with UEFI. To enter setup hold DEL or ESC key on boot. Default UEFI Administrator password is: bcndk1 For users using graphics IC it's advisable to disable display with: i915.disable_display=1 appending to kernel command line inside bootloader, to save about 0.5-0.6W energy on idle. For users not using graphics IC, disable it in UEFI, this will save about 1.5W energy on idle. Pins marked CN19 are ATX power On/Off button. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-WallArınç ÜNAL2023-02-031-1/+0
| | | | | | | | | | The correct compatible string for the multi-chip module MT7530 switch in MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the property on TP-Link EAP615-Wall which will default to the said string. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: use on-flash partition table for Sercomm BZV/CHJJan Hoffmann2023-02-032-8/+330
| | | | | | | | | | | | | | | | | | | These devices have a partition table stored in flash, which compensates for any pre-existing bad blocks by enlarging the respective partition. This means that the current static partition table is only correct for devices without any bad blocks. Typical results of this mismatch are degraded wireless performance and wrong MAC addresses, when the factory partition is shifted due to a bad block somewhere before it. If there is a bad block already before the ubi partition, then OpenWrt may not run at all because the kernel can't find the rootfs. Use the on-flash partition table to fix these issues. Replace the two reserved partitions by the full partition list, as the driver does not allow merging them. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* treewide: strip useless `default n` Kconfig linesTony Butler2023-02-035-11/+0
| | | | | | | | | | Kconfig docs say: > The default value deliberately defaults to 'n' in order to avoid > bloating the build. Apply this rule everywhere, to avoid more cloning of bad examples Signed-off-by: Tony Butler <spudz76@gmail.com>
* ramips: add support for TP-Link Deco M4R v4Mark Ceeha2023-02-034-0/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the V4 hardware revision of the Deco M4R. V4 is a complete overhaul of the hardware compared to V1 and V2, and is much more similar to the Archer C6 V3 and C6U V1. Specifications: SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads) RAM: Kingston D1216ECMDXGJD (256 MB) Wireless 2.4 GHz: MediaTek MT7603EN Wireless 5 GHz: MediaTek MT7613BEN Flash: 16 MB SPI NOR Installation: Flash the *-factory.bin image in the U-Boot recovery webserver. You can trigger this webserver by holding the reset button until the LED flashes yellow, or by hooking up to serial pads on the board (clearly labeled GND, RX and TX) and pressing `x` early in boot. Once the factory image has been flashed, you can use the regular upgrade procedure with sysupgrade images for subsequent flashes. Signed-off-by: Mark Ceeha <hi@shiz.me> Tested-by: Mark Ceeha <hi@shiz.me>
* bcm47xx: Refresh kernel 5.15Hauke Mehrtens2023-02-0320-177/+91
| | | | | | | | | | | | | This makes the patches and the kernel configuration apply on top of kernel 5.15. The following patch was removed because the old IDE subsystem was removed from upstream kernel: target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch This was tested successfully on a ASUS WL-500g Premium V1. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm47xx: Copy kernel from 5.10 to 5.15Hauke Mehrtens2023-02-0335-0/+3441
| | | | | | | Copy patches and configuration from kernel 5.10 to kernel 5.15 files. No changes were done. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 20:24:56 +0000