aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* realtek: d-link: add support for dgs-1210-28mp-fAndreas Böhler2022-12-084-90/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General hardware info: ---------------------- D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4 combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable with a total PoE power budget of 370W. Power over Ethernet: -------------------- The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports each. They are controlled by a Nuvoton MCU. In order to enable PoE, the realtek-poe package is required. It is installed by default, but currently it requires the manual editing of /etc/config/poe. Keep in mind that the port number assignment does not match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and 24-17. LEDs and Buttons: ----------------- On stock firmware, the mode button is supposed to switch the LED indicators of all port LEDs between Link Activity and PoE status. The currently selected mode is visualized using the respective LEDs. PoE Max indicates that the maximum PoE budget has been reached. Since there is currently no support for this behavior, these LEDs and the mode button can be used independently. Serial connection: ------------------ The UART for the SoC (115200 8N1) is available via unpopulated standard 0.1" pin header marked J6. Pin1 is marked with arrow and square. Pin 1: Vcc 3.3V Pin 2: Tx Pin 3: Rx Pin 4: Gnd OEM installation from Web Interface: ------------------------------------ 1. Make sure you are booting using OEM in image 2 slot. If not, switch to image2 using the menus System > Firmware Information > Boot from image2 Tools > reboot 2. Upload image in vendor firmware via Tools > Backup / Upgrade Firmware > image1 3. Toogle startup image via System > Firmware Information > Boot from image1 4. Tools > reboot Other installation methods not tested, but since the device shares the board with the DGS-1210-28, the following should work: Boot initramfs image from U-Boot: --------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-073-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: define loadaddr for all UniFi devicesDavid Bauer2022-12-071-0/+2
| | | | | | | | Define the load-address for the DTB of all Ubiquiti UniFi devices using FIT images. From the GPL code we can assume these boards are affected by the same relocating issue with the vendor bootloader. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: also move &slot0 from dtsi down to board dtsDaniel Golle2022-12-073-10/+20
| | | | | | | | | As the referenced MTD partition is only present in the dts, also move &slot0 down to the dts files. Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi") Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: remove redundant flash entry from dtsiDaniel Golle2022-12-073-74/+16
| | | | | | | | | | Splitting-off the common parts of Ruijie RG-EW3200GX PRO and reyee AX3200-E5 went wrong because the flash descriptiom was kept also in the dtsi. Remove it there, as flash definition is added by both board dts files. Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: optimize the firmware recipe for Netgear NAND devicesShiji Yang2022-12-061-11/+7
| | | | | | | | | | | | | | 1. Drop useless character '0xff' before fake filesystem header. 2. Reduce useless padding to shrink the size of the sysupgrade image. 3. Do not check the size of sysupgrade image. It does not make sense to check the size of a compressed package. 4. Do not take the size of netgear header into account because it will not be written to Flash. 5. Use the default lzma compression dictionary parameter '-d24' to get better performance. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert Netgear R6100 radio calibration to nvmem-cellsShiji Yang2022-12-062-6/+12
| | | | | | | | use nvmem-cells implementation to avoid copying art calibration data to rootfs. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: ca8210: Fix crash by zero initializing dataHauke Mehrtens2022-12-062-0/+60
| | | | | | This fixes crashes at bootup on pistachio. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: add support for reyee AX3200-E5Alex Hansen2022-12-066-255/+416
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly different flash layout, install process is the same. Specifications: SoC: MT7622B RAM: 256MB Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR Ethernet: 5x1GbE Switch: MT7531BE WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) 2Keys: Mesh button + Reset button UART: Marked J19 on board. 3.3v, 115200n1 Power: 12V 2.5A Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Alex Hansen <mralexh123@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7621: enable lzma-loader for netis WF2881Joonhyuk Song2022-12-061-1/+2
| | | | | | Fixes boot loader LZMA decompression issues (LZMA ERROR 1) Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
* ramips: mt7621: mikrotik 760igs (hEX S) fix SFPJohn Thomson2022-12-061-0/+1
| | | | | | | | | | | | | This device uses an AR8031/AR8033 chip to convert SoC gmac1 RGMII to 1000base-x or sgmii for the SFP fibre cage. The SFP cage requires phy-mode rgmii-rxid, and without it will not recieve any packets: ethtool -S sfp rx_fcs_errors will increase when packets should be being received, but no other _rx counters will change. Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* mediatek: mt7623: build mt6577_auxadc driver into kernelDaniel Golle2022-12-052-1/+3
| | | | | | | | | Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the thermal-zone doesn't work on MT7623 (it does work fine without this driver on MT7622 and MT7986). Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GRINAGAKI Hiroshi2022-12-051-19/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use ARTIFACTS to generate initramfs-based factory image of I-O DATA WN-AX1167GR instead of redundant recipe which generate on KERNEL_INITRAMFS. Note: WN-AX1167GR has 2x OS images on stock firmware. stock log: flash manufacture id: c2, device id 20 18 MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" 1st image is "Kernel" and 2nd is "app" when booted from 1st image. In OpenWrt, those 2x partitions are combined to "firmware" with undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff). The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so check-size for initramfs-factory image needs to be called with the size. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for HiWiFi HC5611Senis John2022-12-045-0/+44
| | | | | | | | | | | | | | | | | | | | | | | CPU: MediaTek MT7628AN @ 575 MHz Flash: 16 MB RAM: 128 MB Ethernet: 10/100Mbps x 1 Wlan: 300 Mbps USB: USB 2.0 x 1 LED: red/green x 1 Button: reset x 1 1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh 2. Upload the openwrt firmware to the router via SCP 3. Login the router via SSH 4. Run `mtd -r write path_to_firmware.bin firmware` I have tested on my device. - The LED will display RED on power-on, After system start completed, trun GREEN - Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device - USB can working under official u-boot Signed-off-by: Senis John <thank243@gmail.com>
* rockchip: enable watchdog driverKien Truong2022-12-041-1/+2
| | | | | | | | Enable Synopsys DesignWare watchdog driver for rockchip device Tested on NanoPi R2S Signed-off-by: Kien Truong <duckientruong@gmail.com>
* Revert "mvebu: switch default kernel to 5.15"Petr Štetiar2022-12-041-1/+2
| | | | | | | | | | | | | | This reverts commit 5429411f732ba76eced30b5b596ec9c0374d0965 as upstream in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel. That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in those builds, which leads to a broken LAN bridge network on several devices. References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: enable lzma-loader for ZyXEL WAP6805Bjørn Mork2022-12-031-1/+2
| | | | | | | Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover". Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mvebu: switch default kernel to 5.15Stijn Segers2022-12-021-2/+1
| | | | | | | | | | | | | In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu to 5.15 which has been the testing kernel on this target since April - over half a year. Run-tested on the following subtargets: * cortexa9 (Turris Omnia - 03f41b1eb2f15ab06d5800274be6a67c64e2a629) * cortexa72 (MikroTik RB5009UG+S+IN) Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000] Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* realtek: fix dell typoJan-Niklas Burfeind2022-12-011-3/+3
| | | | | | | should be add/delete or abbreviated add/del Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
* realtek: refactor keep vlan tag setup, fix tagged forwardingLuiz Angelo Daros de Luca2022-12-017-23/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The code in dsa.c:rtl83xx_port_enable() was trying to set vlan_port_tag_sts_ctrl while dealing with differences between SoCs. However, not only that register has a different address, the register structure and even the 2-bit value semantic changes for each SoC. The vlan_port_tag_sts_ctrl field was dropped and converted into a vlan_port_keep_incoming_tag_set() function that abstracts the different between SoCs. The macro referencing that register migrated to the SoC specific c file as it will be privately used by each file. All magic numbers were converted into macros using BITMASK and FIELD_PREP. The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already broken for rtl93xx. The best place for SoC specific code might be in each respective c file and not in if/else clauses. The final result is: rtl838x: set ITAG_STS=TAGGED, same as before rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing forwarding of tagged packets rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly fixing forwarding of tagged packets rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly fixing forwarding of tagged packets Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets will drop the vlan tag while packets from the CPU will still have the correct tag. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* realtek: Fix rtl930x speed status accessorOlliver Schinagl2022-12-011-3/+3
| | | | | | | | | | | | | | The rtl930x speed status registers require 4 bits to indicate the speed status. As such, we want to divide by 8. To make things consistent with the rest of this code, use a bitshift however. This bug probably won't affect many users yet, as there aren't many rtl930x switches in the wild yet with more then 10 ports, and thus a low-impact bugfix. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> [also fix port field extraction] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-279-217/+347
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* airoha: disable swconfigAleksander Jan Bajkowski2022-11-271-1/+0
| | | | | | | | Swconfig isn't used by this target and can be disabled for this reason. Airoha doesn't even have an Ethernet driver. In the future, this target should get a DSA driver. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* airoha: refresh configAleksander Jan Bajkowski2022-11-271-4/+4
| | | | | | | This was done by executing these command: $ time make kernel_oldconfig CONFIG_TARGET=platform Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* layerscape: kmod-ppfe: Use ppfe driver as modulePawel Dembicki2022-11-273-5/+5
| | | | | | | | | | | In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module. This patch switch kmod-ppfe from build-in to loadable module. Loadable module helps to avoid hazard: driver is looking for firmware file before mount root. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: switch kernel testing to 5.15Pawel Dembicki2022-11-271-1/+1
| | | | | | | | | Let's test layerscape with 5.15 kernel. Run tested: LS1012A-FRDM, LS1046A-RDB (nor and sd-boot images), LS1021A-IOT (By @ArtelMike with u-boot fix) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: Switch LS1012A-FRDM initramfs to gzipPawel Dembicki2022-11-271-1/+0
| | | | | | | | | | At this moment LS1012A-FRDM have uncompressed initramfs image. Error was caused, because gzip extract area overlap image. Let's change loadaddr and enable gzip initramfs images again. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: remove kernel 5.4 dependencesPawel Dembicki2022-11-271-28/+0
| | | | | | 5.4 kernel was removed. Let's clean old dependences. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: 5.15: refresh kernel configPawel Dembicki2022-11-272-28/+42
| | | | | | Done by 'make kernel_oldconfig'. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: copy patches 5.10 to 5.15Pawel Dembicki2022-11-279-0/+12571
| | | | | | | | | | One patch manually rebased: 302-arm64-dts-ls1012a-update-with-ppfe-support.patch PFE driver patch recreated from NXP 5.15 tree: 701-staging-add-fsl_ppfe-driver.patch Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: copy config 5.10 to 5.15Pawel Dembicki2022-11-272-0/+1516
| | | | | | Configs was just copied. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: refresh kernel configPawel Dembicki2022-11-272-10/+1
| | | | | | Done by 'make kernel_oldconfig'. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: Fix SPI-NOR issues with vendor patchesPawel Dembicki2022-11-274-0/+130
| | | | | | | | | | | | | | | | | | | | For some reason LS1012A and LS1046A devboards don't work well with Spansion SPI NOR flash. It cause read and write errors like: [ 27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000 [ 27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000 [ 27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000 [ 27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000 [ 27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000 [ 27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000 [ 27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000 [ 27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000 NXP have found workarround and applied in their vendor kernel version. They force 1x tx and 1x rx lines in qspi. That method fix issues. This patch ports patches from NXP LSDK tree. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: D-Link DIR-825 B1 add factory.bin recipeWill Moss2022-11-271-4/+6
| | | | | | | | | | - Bring back factory.bin image which was missing after porting device to ath79 target - Use default sysupgrade.bin image recipe - Adjust max image size according to new firmware partition size after "ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes - Remove support of upgrading from version 19.07, because partition size changes mentioned above Signed-off-by: Will Moss <willormos@gmail.com>
* ath79: add support for Senao Engenius EAP1750HMichael Pratt2022-11-274-0/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EAP1750H Engenius EAP1750H is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ **Specification:** - QCA9558 SOC - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16FG - UART at J10 populated - 4 internal antenna plates (5 dbi, omni-directional) - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset) **MAC addresses:** MAC addresses are labeled as ETH, 2.4G, and 5GHz Only one Vendor MAC address in flash eth0 ETH *:fb art 0x0 phy1 2.4G *:fc --- phy0 5GHz *:fd --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** 2 ways to flash factory.bin from OEM: Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware Upgrade" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board, interrupt boot execute tftpboot and bootm 0x81000000 NOTE: TFTP is not reliable due to bugged bootloader set MTU to 600 and try many times if your TFTP server supports setting block size higher block size is better. **Format of OEM firmware image:** The OEM software of EAP1750H is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin openwrt-ar71xx-generic-eap1750h-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: use nvmem-cells for radio calibration of EAP1200HMichael Pratt2022-11-273-7/+19
| | | | | | Transition from userscript to DTS for all of ART. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: calibrate TP-LINK TL-WR2543ND with nvmemEdward Chow2022-11-272-5/+13
| | | | | | | | | | | | | | | | | Driver for and pci wlan card now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my tplink tl-wr2543nd. Signed-off-by: Edward Chow <equu@openmail.cc>
* kernel: bump 5.10 to 5.10.156John Audia2022-11-274-13/+13
| | | | | | | | Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.80John Audia2022-11-2720-50/+49
| | | | | | | | | | | | | | Manually rebase: pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch ath79/patches-5.15/910-unaligned_access_hacks.patch All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* ipq806x: disable cache and fabric devfreq driver to improve stabilityChristian Marangi2022-11-261-2/+2
| | | | | | | | | | | | It was tested that cache scaling currently cause instability problem. This is probably caused by a latent misconfiguration that cause the L2 cache to be sourced from the wrong source and runs at an unstable freq compared to the original QSDK fw. To improve stability while the problem is bisected, disable the devfreq drivers with minimal perf penality. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622Felix Fietkau2022-11-252-9/+5
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: set persistent wifi mac for bpi-r64 and bpi-r3Daniel Golle2022-11-242-0/+21
| | | | | | | Use persistent MAC address for the built-in wireless interfaces of the BPi-R64 and BPi-R3 development boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove '-fit' string from kernel filenamesDaniel Golle2022-11-241-4/+4
| | | | | | | | The type of those images is already distinguishable by the '.itb' extension, there is no need for an additional '-fit' string in the filenames. Remove it to behave more like other targets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove 'nand-' string from image filenamesDaniel Golle2022-11-242-16/+16
| | | | | | | | | Only on the ipq40xx subtarget different filenames were used for NAND- based devices. This is unneeded, confusing and breaks downstream tools such as luci-app-attendedsysupgrade and auc. Remove the 'nand-' string from image filenames to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm27xx: sound-soc-justboom-*: fix packagesEdmunt Pienkowsky2022-11-231-12/+25
| | | | | | | | | Affected packages: sound-soc-justboom-both, sound-soc-justboom-dac and sound-soc-justboom-digi. - Add snd-soc-wm8804-i2c and/or snd-soc-pcm512x-i2c kernel modules. - Add kmod-regmap-i2c package dependency. Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
* bcm27xx: sound-soc-hifiberry-digi: fix packageEdmunt Pienkowsky2022-11-231-4/+7
| | | | | | | - Add snd-soc-wm8804-i2c kernel module, - Add kmod-regmap-i2c package dependency. Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
* bcm27xx: disable duplicate sdhost driverJohn Audia2022-11-234-8/+6
| | | | | | | | | | | | | | | | Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this error in dmesg: Error: Driver 'sdhost-bcm2835' is already registered, aborting... Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled avoids this error. Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me> [Disable driver for all subtargets, refresh configs, tweak description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: fix regression on mt7986Felix Fietkau2022-11-231-10/+2
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add WED rx support for mediatekFelix Fietkau2022-11-215-0/+3077
| | | | | | This is required for rx flow offloading on mt76 with MT7986 and MT7915 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add a locking fix for netfilter hardware flow offloadingFelix Fietkau2022-11-212-0/+78
| | | | | | | Protect the flow block cb list readers against concurrent updates Reported-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 11:00:01 +0000