| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40360
|
|
|
|
|
|
|
|
| |
uImage cannot be built in parallel properly until zImage is ready
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40359
|
|
|
|
|
|
|
|
| |
We would fail to copy an non-existent uImage-initramfs to $(BIN_DIR)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40358
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40352
|
|
|
|
|
|
|
|
|
| |
This backports: bcma: gpio: register 32 GPIOs on BCM5357
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40347
|
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40346
|
|
|
|
|
|
|
|
|
| |
Handle it by creating a new patch for simple database changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40345
|
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40344
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40342
|
|
|
|
|
|
|
|
| |
apparently this one was nt a good idea to merge
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40330
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40328
|
|
|
|
|
|
|
|
| |
http://patchwork.openwrt.org/patch/3703/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40326
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
SVN-Revision: 40324
|
|
|
|
|
|
|
|
| |
http://patchwork.openwrt.org/patch/4417/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40323
|
|
|
|
|
|
| |
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40321
|
|
|
|
|
|
|
|
|
| |
- Set correct AltSel for STP pins
- Set front button to rfkill
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40320
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
|
|
|
|
|
|
|
|
| |
If gphys are not reset upstream uboot can not use them anymore.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40318
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
|
|
|
|
|
|
| |
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40316
|
|
|
|
|
|
| |
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40315
|
|
|
|
|
|
| |
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40314
|
|
|
|
|
|
| |
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40313
|
|
|
|
|
|
|
|
|
|
| |
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40312
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40311
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40310
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40309
|
|
|
|
|
|
|
|
| |
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
SVN-Revision: 40306
|
|
|
|
|
|
|
|
|
|
| |
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
|
|
|
|
|
|
|
|
|
|
| |
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
|
|
|
|
|
|
|
|
|
|
|
| |
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40294
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40291
|
|
|
|
|
|
|
|
|
|
|
| |
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40038
|
|
|
|
|
|
|
|
| |
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40036
|
|
|
|
|
|
|
|
|
| |
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40031
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40023
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40022
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Function move_config should be called after or during preinit_mount_root
hook in do_mount_root function. At this state sysupgrade.tgz is not in its
place during that time when do_mount_root is called. Function move_config
is called later so the sysupgrade.tgz stays in root directory to the second
restart when it is unpacked properly.
This patch adds move_config function to preinit_mount_root hook instead
of preinit_main and changes the filename of script to be called before
80_mount_root is called. It will prepare the sysupgrade archive for do_mount_root
within preinit_mount_root hook.
This issue was introduced for target x86. Since the target for x86_64 is
similar to x86, this issue is present also in this target. It solves the
ticket #15042 and #14088.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
Tested-By: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 39997
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Function move_config should be called after or during preinit_mount_root
hook in do_mount_root function. At this state sysupgrade.tgz is not in its
place during that time when do_mount_root is called. Function move_config
is called later so the sysupgrade.tgz stays in root directory to the second
restart when it is unpacked properly.
This patch adds move_config function to preinit_mount_root hook instead
of preinit_main and changes the filename of script to be called before
80_mount_root is called. It will prepare the sysupgrade archive for do_mount_root
within preinit_mount_root hook.
This patch solves ticket #15042 and #14088.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 39996
|
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39973
|
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39972
|
|
|
|
|
|
|
|
|
| |
hstimer DT on A20
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
SVN-Revision: 39971
|
|
|
|
|
|
|
|
|
|
| |
Patch 642-bridge_port_isolate.patch needs to be updated
for kernels 3.12, 3.13 and 3.14 as the define for BR_ISOLATE_MODE
conflicts with BR_LEARNING
Signed-off-by: Jonas Eymann <j.eymann@gmx.net>
SVN-Revision: 39955
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39950
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39949
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39948
|