aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: ar40xx: reset port status registerDavid Bauer2021-10-241-2/+1
| | | | | | | | This resolves incosnsitencies of the configured RX / TX flow control modes between different boards or bootloaders. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4d81f087715524994448ecaefd3ca87c8ba7e0a3)
* ath79: mikrotik: use 64 KiB SPI NOR erase sectorsRoger Pueyo Centelles2021-10-221-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default symbols for the ath79/mikrotik target. MikroTik devices hold some of their user-configurable settings in the soft_config partition, which is typically sized 4 KiB, of the SPI NOR flash memory. Previously, in the ar71xx target, it was possible to use 64 KiB erase sectors but also smaller 4 KiB ones when needed. This is no longer the case in ath79 with newer kernels so, to be able to write to these 4 KiB small partitions without erasing 60 KiB around, the CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults. However, this ended up making sysupgrade images which were built with 64 KiB size blocks not to keep settings (e.g., the files under /etc/config/) over the flashing process. Using 4 KiB erase sector size on the sysupgrade images (by setting BLOCKSIZE = 4k) allows keeping settings over a flashing process, but renders the process terribly slow, possibly causing a user to mistakenly force a manual device reboot while the process is still on- going. Instead, ditching the 4 KiB erase sectors for the default 64 KiB erase size provides normal SPI write speed and sysupgrade times, at the expense of not being able to modify the soft_config partition (which is rarely a required thing). An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have allowed to use different per-partition erase sector sizes. Due to changes on recent kernels it now only works on a per-device basis. Also, partial eraseblock write can be performed in ath79 with kernels 5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole sector and restoring those blocks not meant to be modified. A kernel bump had that patch broken for a long time, but got fixed in bf2870c. Note: the settings in the soft_config partition can be reset to their defaults by holding the reset button for 5 seconds (and less than 10 seconds) at device boot. Fixes: FS#3492 (sysupgrade […] loses settings...) Fixes: a66eee63368e (ath79: add mikrotik subtarget) Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> (cherry picked from commit 68d91f08edd0efd47841a2e53d3437d570a61612)
* layerscape: Add missing config optionHauke Mehrtens2021-10-221-0/+1
| | | | | | | This option is not set when building the target. In master this is also unset. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* layerscape: Fix build in dtbHauke Mehrtens2021-10-2223-64/+37
| | | | | | | | | This fixes a kernel build problem. The removed parts of the patch are already applied upstream. Fixes: b4ed8a92751f ("kernel: bump 5.4 to 5.4.154") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 9501ce909f54b87dab95f17c0408a4962365e130)
* kernel: bump 5.4 to 5.4.154Hauke Mehrtens2021-10-2031-1718/+68
| | | | | | | | | | | | Removed upstreamed: generic/backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for iEi Puzzle-M901/Puzzle-M902Ian Chang2021-10-146-0/+868
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz * 4 GB DDR * 4 GB eMMC * mmcblk0 - mmcblk0p1 64M kernel_1 - mmcblk0p2 64M kernel_2 - mmcblk0p3 512M rootfs_1 - mmcblk0p4 512M rootfs_2 - mmcblk0p5 512M Reserved - mmcblk0p6 64M Reserved - mmcblk0p7 1.8G rootfs_data * 4 MB (SPI Flash) * 6 x 2.5 Gigabit ports (Puzzle-M901) - External PHY with 6 ports (AQR112R) * 6 x 2.5 Gigabit ports (Puzzle-M902) - External PHY with 6 ports (AQR112R) 3 x 10 Gigabit ports (Puzzle-M902) - External PHY with 3 ports (AQR113R) * 4 x Front panel LED * 1 x USB 3.0 * Reset button on Rear panel * UART (115200 8N1,header on PCB) Flash instructions: The original firmware is based on OpenWrt. Flash firmware using LuCI and CLI Signed-off-by: Ian Chang <ianchang@ieiworld.com> (cherry picked from commit 70c75965a97799b44871249c205bad48fea9a4ae) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mvebu: backport CN9130 dts necessary files changes to 5.4Ian Chang2021-10-1410-0/+2883
| | | | | | | | | | | 1. Add support for Marvell CN9130 SoC 2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115 3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series 4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file Signed-off-by: Ian Chang <ianchang@ieiworld.com> (cherry picked from commit c98ddf0f019986bbb4c868bfcaf97e0d1f4ee2dc) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: ar8216: add get_features methodDavid Bauer2021-10-121-23/+20
| | | | | | | | | | | | | | | Modifying PHY capabilities in the probe function broke with upstream commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the supported features"). AR8316 switches only support 10/100 Mbit/s link modes because of this change. Provide a get_features method for the PHY driver, so Gigabit link mode will be advertised to link partners again. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 766e0f584a325b0b80a97bbc86ca515d97c63001)
* kernel: bump 5.4 to 5.4.150Hauke Mehrtens2021-10-0274-267/+173
| | | | | | | | | | | | | | | | | | Manually rebased: generic/backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch Removed upstreamed: generic/backport-5.4/040-ARM-8918-2-only-build-return_address-if-needed.patch layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rockchip: fix broken squashfs sysupgradeDavid Bauer2021-09-241-1/+1
| | | | | | | | | | | | | | | The rockchip platform supports squashfs SD card images. However, the resulting image is not padded to completely fill the rootfs partition. Because of that, the f2fs overlay might not be erased, resulting in uci-defaults not bing executed or the configuration not being erased, even though drop config was selected. Modify the image generation process so the image is padded to cover the entire root filesystem partition. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit b56f7407d999d29c200c8c5880655926ef9874b7)
* apm821xx: MBL: band-aid MBL DUOChristian Lamparter2021-09-231-18/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Takimata reported on the OpenWrt forum in thread [0], that his MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading from the previous OpenWrt 19.07. The last logged entries on his console |[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored |[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored |[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300) |[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) |[ 5.909555] ata1.00: qc timeout (cmd 0xec) |[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) |[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300) This extract clearly showed that the HDD on which OpenWrt is installed, simply disappeared after the SATA power regulators had been initialized. Since the device-tree regulators haven't changed since the OpenWrt 19.07 days this will require further investigation on the snapshot/master/trunk branch. For the time being, it was requested to just delete the nodes so, the device will boot again. Which unfortunately, will have to wait until 21.02.1 is released. He also confirmed that the My Book Live Single wasn't affected. It works with or without this change. [0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585> Reported-by: Takimata (forum.openwrt.org/u/takimata) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for minew g1-cAlexander Couzens2021-09-213-0/+152
| | | | | | | | | | | | | | | | | | | | | | The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200Sven Eckelmann2021-09-191-1/+1
| | | | | | | | | | | | The board data file for the Plasma Cloud PA2200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit c7e9335e4c23f3bd074cb2b215a289b8b75f319c)
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200Sven Eckelmann2021-09-191-1/+1
| | | | | | | | | | | | The board data file for the Plasma Cloud PA1200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit d0ffc175350f2be6174932dc0afd4d2737afe52d)
* ipq40xx: Select correct board-2.bin for EnGenius EMR3500Sven Eckelmann2021-09-191-0/+1
| | | | | | | | | | The board data file for the EnGenius EMR3500 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 3f61e5e1b97e ("ipq40xx: add support for EnGenius EMR3500") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 14bd392a1cd0b8e267e4402ae27b3c5a8f66b933)
* ipq40xx: Select correct board-2.bin for EnGenius EMD1Sven Eckelmann2021-09-191-0/+1
| | | | | | | | | | The board data file for the EnGenius EMD1 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 51f303597839 ("ipq40xx: add support for EnGenius EMD1") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit d9f4a4280e674ddb4ec75ae2d73b0f86e0c282cc)
* kernel: backport switchdev fix for bridge in bridge configurationsFabian Bläse2021-09-131-0/+60
| | | | | | | | | | | | | | | | | | | | This patch fixes the forwarding behavior of bridge in bridge configurations with DSA. Without it, the configuration of the upper bridge might overwrite settings of the lower bridge. For example, a vlan-aware bridge with DSA interfaces in it might be offloaded to the DSA hardware. If the bridge interface itself gets slave of a different bridge without vlan filtering, the vlan filtering setting of the lower bridge is overwritten by the upper bridge, which results in an incorrect hardware configuration. This was backported from kernel 5.7. Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/ Fixes: FS#3996 Signed-off-by: Fabian Bläse <fabian@blaese.de> (cherry picked from commit c50ece58c41647880cc74c927d98b465cdfbdad8)
* kernel: Add missing kernel config optionsHauke Mehrtens2021-09-134-5/+3
| | | | | | | | These options are selectable when some of the kernel debug options like KERNEL_SOFTLOCKUP_DETECTOR are selected. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 1a3b3dc7974c98843baeb22251dc4c580dc771d6)
* kirkwood: increase kernel partition of LinksysesPawel Dembicki2021-09-132-4/+6
| | | | | | | | | | | | | | | At this moment kernel partition in Linksyses EA3500/E4200/EA4500 is ended before start of rootfs partition. It was introduced in 9808b9ae02 and it broke easy revert to stock. Sysupgrade, when OFW is used, write whole stock image to kernel partition. Most likeley image will be bigger than small kernel partition and it make stock system invalid. This patch change size of kernel partitions and now it overlaps rootfs. Revert to stock will be possible again. Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9") Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mvebu: limit mvneta tx queue workaround to 32 bit SoCTomasz Maciej Nowak2021-09-091-2/+6
| | | | | | | | | | | | | This patch has been carried since introduction throughout every kernel major bump and no one has tested if the later kernels improved the situation. The Armada 3720 SoC can only process GbE interrupts on Core 0 and this is already limited in all stable kernels, so ditch this workaround for 64 bit SoCs. Ref: https://git.kernel.org/torvalds/c/cf9bf871280d Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (cherry picked from commit cbdd2b62e4d5e0572204c37d874d32dc8610840e)
* ath79: add support for onion omegaJan-Niklas Burfeind2021-09-013-0/+139
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Onion Omega is a hardware development platform with built-in WiFi. https://onioniot.github.io/wiki/ Specifications: - QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor) - 64MB of DDR2 RAM running at 400 MHz - 16MB of on-board flash storage - Support for USB 2.0 - Support for Ethernet at 100 Mbps - 802.11b/g/n WiFi at 150 Mbps - 18 digital GPIOs - A single Serial UART - Support for SPI - Support for I2S Flash instructions: The device is running OpenWrt upon release using the ar71xx target. Both a sysupgrade and uploading the factory image using u-boots web-UI do work fine. Depending on the ssh client, it might be necessary to enable outdated KeyExchange methods e.g. in the clients ssh-config: Host 192.168.1.1 KexAlgorithms +diffie-hellman-group1-sha1 The stock credentials are: root onioneer For u-boots web-UI manually configure `192.168.1.2/24` on your computer, connect to `192.168.1.1`. MAC addresses as verified by OEM firmware: 2G phy0 label LAN eth0 label - 1 LAN is only available in combination with an optional expansion dock. Based on vendor acked commit: commit 5cd49bb067ca ("ar71xx: add support for Onion Omega") Partly reverts: commit fc553c7e4c8e ("ath79: drop unused/incomplete dts") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> (cherry picked from commit d98738b5c118fc45068b45f07b8b6938e91f35d2)
* kernel: bump 5.4 to 5.4.143Hauke Mehrtens2021-08-2916-62/+23
| | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.4/950-1031-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch Removed upstreamed: mvebu/patches-5.4/100-cpufreq-armada-37xx-forbid-cpufreq-for-1.2-GHz-variant.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.142David Bauer2021-08-2427-213/+75
| | | | | | | Compile-tested: ath79-generic ipq40xx-generic Run-tested: ipq40xx-generic Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix Edgecore ECW5211 bootStijn Tintel2021-08-241-0/+1
| | | | | | | | The bootloader will look for a configuration section named ap.dk01.1-c2 in the FIT image. If this doesn't exist, the device won't boot. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit a43da1be43ae251f0edaa6419612e600fc6ec972)
* ath79: kernel: Add missing quote to drivers/mfd/KconfigPaul Blazejowski2021-08-221-1/+1
| | | | | | | | | | | | | | | A missing quote in target/linux/ath79/patches-5.x/920-mikrotik-rb4xx.patch produces: ... scripts/kconfig/conf --syncconfig Kconfig drivers/mfd/Kconfig:2016:warning: multi-line strings not supported ... This patch adds missing closing quote, fixing the above warning. Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net> (cherry picked from commit f7374bce00a97fda78ace3acaef48369e8246814)
* x86: kernel: set NR_CPUS to 512Edgar Su2021-08-111-2/+2
| | | | | | | | | | | NR_CPUS limits the number of CPUs supported to 8. This makes total sense on hardware-restircted platforms, but not on x86_64, where CPUs with more than 8 cores can be easily acquired and with less physical limitaions. see also: https://forum.openwrt.org/t/x86-64-8-cpu-limitation-on-vanilla-release/100946 Signed-off-by: Edgar Su <sjs333@outlook.com> (cherry picked from commit df554e6fcab171ec499d8fb2ed10a0da328323f3)
* mvebu: armada-37xx: add patch to forbid cpufreq for 1.2 GHzJosef Schlehofer2021-08-081-0/+39
| | | | | | | | | | | This patch is backported from linux-arm-kernel [1] to improve situation, when it was reported that 1.2 GHz variant is unstable with DFS. It waits to be accepted upstream, however, it waits for Marvell people to respond. [1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210630225601.6372-1-kabel@kernel.org/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit d3794768177293f584cc74f90c921276793da1e7)
* Revert "mvebu: 5.4 fix DVFS caused random boot crashes"Josef Schlehofer2021-08-081-107/+0
| | | | | | | | | | | | | | | | | | | | | | | | | Based on the discussion on the mailing list [1], the patch which was reverted, it reverts only one patch without the subsequent ones. This leads to the SoC scaling issue not using a CPU parent clock, but it uses DDR clock. This is done for all variants, and it's wrong because commits (hacks) that were using the DDR clock are no longer in the mainline kernel. If someone has stability issues on 1.2 GHz, it should not affect all routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to improve the situation in the kernel and not making the situation worse. There are two solutions in cases of instability: a) disable cpufreq b) underclock it up to 1 GHz This reverts commit 080a0b74e39d159eecf69c468debec42f28bf4d8. [1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html CC: Pali Rohár <pali@kernel.org> Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit 7b868fe04a8961048feec1143e72fe47bde52a12)
* kernel: bump 5.4 to 5.4.137Hauke Mehrtens2021-07-3165-148/+149
| | | | | | | | | | | | Manually rebased generic/pending-5.4/680-NET-skip-GRO-for-foreign-MAC-addresses.patch All others updated automatically. Compile-tested on: ramips/mt7621, armvirt/32 Runtime-tested on: ramips/mt7621, armvirt/32 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mt76x8: add missing config symbolDavid Bauer2021-07-301-0/+1
| | | | | | PWM_MEDIATEK was not defined, breaking builds for the mt76x8 subtarget. Signed-off-by: David Bauer <mail@david-bauer.net>
* x86: move Kconfig symbol to common configDavid Bauer2021-07-304-3/+1
| | | | | | | This is required for all x86 targets. x86-legacy missed this config symbol, breaking the build. Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: add missing Kconfig symbolDavid Bauer2021-07-301-0/+2
| | | | | | Fixes build errors for sunxi as well as rockchip targets. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix JT-OR750i switch LED assignmentDavid Bauer2021-07-291-2/+2
| | | | | | | | The LEDs for LAN1 and LAN3 were swapped. Link on port 1 would illuminate the LED on port 3 and vice versa. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f0a885ed8636b9762d12f2eb2755f63297ff0cb5)
* ath79: enable missing pinmux for JT-OR750iDavid Bauer2021-07-291-0/+3
| | | | | | | | Without explicit configuration of these pins the ethernet as well as status LED of the device do not work correctly. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4feb9a4211d4c8e118e6b8f01fa0bbd4eab5d35c)
* ath79: add support for Joy-IT JT-OR750iVincent Wiemann2021-07-295-0/+137
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM * 802.11n 2T2R (external antennas) * QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas) * 3x 10/100 LAN, 1x 10/100 WAN * UART header with pinout printed on PCB Installation: * The device comes with a bootloader installed only * The bootloader offers DHCP and is reachable at http://10.123.123.1 * Accept the agreement and flash sysupgrade.bin * Use Firefox if flashing does not work TFTP recovery with static IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server at 192.168.0.66 * Keep the reset button pressed for 4 seconds after connecting power TFTP recovery with dynamic IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server with a DHCP server running at the same address * Keep the reset button pressed for 6 seconds after connecting power Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com> (cherry picked from commit 55b4b3655263984b92e4b9fc515a5e6b8003c655)
* kernel: bump 5.4 to 5.4.132Hauke Mehrtens2021-07-1941-129/+129
| | | | | | | | | | | | Manually rebased layerscape/patches-5.4/805-display-0002-drm-rockchip-prepare-common-code-for-cdns-and-rk-dpi.patch All others updated automatically. Compile-tested on: ramips/mt7621 Runtime-tested on: ramips/mt7621 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: fix FRITZRepeater 1200 RGMII delayDavid Bauer2021-07-171-1/+1
| | | | | | | | | | | | | | | When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the at803x PHY driver incorrectly set up the delays, not disabling delays set by the bootloader. The PHY was always operating with RX as well as TX delays enabled, but with kernel 5.4 and later, the required TX delay is disabled, breaking ethernet operation. Correct the PHY mode, so the driver enables both delays. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f9d18281051c894eacd40f10c10b430c6c9082ad)
* mpc85xx: add missing Kconfig symbolsDavid Bauer2021-07-132-0/+2
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add missing config symbolsDavid Bauer2021-07-131-0/+3
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: add missing config symbolsDavid Bauer2021-07-131-0/+11
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add missing MTD_NAND_RB91X symbolKoen Vandeputte2021-07-091-0/+1
| | | | | | | | Looks like the symbol was forgotten for 5.4 Fixes: 820e660cd7 ("ath79: add NAND driver for MikroTik RB91xG series") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry picked from commit 52c27dab1973d523453fc1e319d8636e1cb10927)
* ath79: add missing GPIO_LATCH symbolDavid Bauer2021-07-091-0/+1
| | | | | | | Fixes commit 7b8931678c36 ("ath79: add gpio-latch driver for MikroTik RouterBOARDs") Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f2f137593eb6c0e849352e85c003c91f8be81dd1)
* ath79: mikrotik: fix beeper phantom noise on RB912Koen Vandeputte2021-07-091-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Analysis done by Denis Kalashnikov: It seems that some ROS versions on some routerboard models have this bug: after silence boot (no output to uart, no beeps) beeper clicks when wireless traffic is. https://forum.mikrotik.com/viewtopic.php?f=3&t=92269 https://forum.mikrotik.com/viewtopic.php?t=63399 From these links: 1) Hello, I have RB951G-2HnD and I noticed strange thing when I loaded the device with some wireless traffic it produced strange sound - like hissing, fizzing etc. 2) Same problem still on 6.33, with silent boot enabled I hear buzzing noise on wireless load. 3) The sound is fixed in v5.19, it was a bug that caused beeper to make clicks. It also got fixed in RouterOS: * What's new in 5.19 (2012-Jul-16 10:51): fix ticking sound on RB411UAHL; * What's new in 6.38.3 (2017-Feb-07 09:52): rb3011 - fixed noise from buzzer after silent boot; I've checked with an oscilloscope that: * When on the ssr beeper pin is 0, on the beeper itself is 1 (~5V), and when on the ssr beeper pin is 1, on the beeper is 0 The beeper doesn't consume power, so 1 should be a default/idle value for the ssr beeper pin). * When there is wireless traffic (ping packets) in the background and the beeper clicks, I see pulses on the beeper itself, but no pulses on the ssr beeper pin (Q5 pin of 74hc595). When I manually toggle the ssr beeper pin I see pulses on both. So, it is likely that the phantom beeper clicks are caused by the EMI. Suggested-by: Denis Kalashnikov <denis281089@gmail.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry picked from commit a58bcc9e673db3c6aa39f2089d216d51c8356418)
* ath79: ar934x: fix mounting issues if subpage is not supportedKoen Vandeputte2021-07-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the option to disable subpage writing is only set when a HW ECC engine is used. Some boards lack a HW ECC engine and use software for that. In this case, this NAND option does not get set when the NAND chip does not support it, resulting in mounting errors. Move the setting of this option to a generic init location so it gets set for all types where required. While at it, also OR the option instead of just setting it so we don't overwrite potential flags being set somewhere else. Before: [ 1.681273] UBI: auto-attach mtd2 [ 1.684669] ubi0: attaching mtd2 [ 1.688877] ubi0 error: validate_ec_hdr: bad VID header offset 2048, expected 512 [ 1.696469] ubi0 error: validate_ec_hdr: bad EC header [ 1.701712] Erase counter header dump: [ 1.705512] magic 0x55424923 [ 1.709322] version 1 [ 1.712330] ec 1 [ 1.715331] vid_hdr_offset 2048 [ 1.718610] data_offset 4096 [ 1.721880] image_seq 1462320675 [ 1.725680] hdr_crc 0x12255a15 After: 1.680917] UBI: auto-attach mtd2 [ 1.684308] ubi0: attaching mtd2 [ 2.954504] random: crng init done [ 3.142813] ubi0: scanning is finished [ 3.163455] ubi0: attached mtd2 (name "ubi", size 124 MiB) [ 3.169069] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.176037] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.182942] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.190013] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0 [ 3.196102] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 3.203434] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1462320675 [ 3.212700] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20 [ 3.222124] ubi0: background thread "ubi_bgt0d" started, PID 317 [ 3.230246] block ubiblock0_1: created from ubi0:1(rootfs) [ 3.235819] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 3.256830] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry-picked from commit 6561ca1fa510003a19ea7f8800535f12e5098ce2)
* ath79: add support for MikroTik RouterBOARD 912UAG-2HPnDDenis Kalashnikov2021-07-095-0/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board has been supported in the ar71xx. Links: * https://mikrotik.com/product/RB912UAG-2HPnD * https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd This also supports the 5GHz flavour of the board. Hardware: * SoC: Atheros AR9342, * RAM: DDR 64MB, * SPI NOR: 64KB, * NAND: 128MB, * Ethernet: x1 10/100/1000 port with passive POE in, * Wi-Fi: 802.11 b/g/n, * PCIe, * USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A port -- both can be used for LTE modem, but only one can be used at any time. * LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED, Ethernet phy LED, * Button, * Beeper. Not working: * Button: it shares gpio line 15 with NAND ALE and NAND IO7, and current drivers doesn't easily support this configuration, * Beeper: it is connected to bit 5 of a serial shift register (tested with sysfs led trigger timer). But kmod-gpio-beeper doesn't work -- we left this as is for now. Flashing: * Use the RouterBOARD Reset button to enable TFTP netboot, boot kernel and initramfs and then perform sysupgrade. * From ar71xx OpenWrt firmware run: $ sysupgrade -F /tmp/<sysupgrade.bin> For more info see: https://openwrt.org/toh/mikrotik/common. Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> (cherry-picked from commit 695a1cd53ca52c678b3f837deb1bf30204285360)
* ath79: add NAND driver for MikroTik RB91xG seriesDenis Kalashnikov2021-07-093-0/+397
| | | | | | | | | | | | | | Main part is copied from ar71xx original driver rb91x_nand written by Gabor Juhos <juhosg@openwrt.org>. What is done: * Support of kernel 5.4 and 5.10, * DTS support, * New gpio API (gpiod_*) support. Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> (cherry-picked from commit 820e660cd7463aa6d5ed9d31baf0f3c35596ce57)
* ath79: add gpio-latch driver for MikroTik RouterBOARDsDenis Kalashnikov2021-07-092-0/+226
| | | | | | | | | | | | | This is a slighty modified version of ar71xx gpio-latch driver written by Gabor Juhos <juhosg@openwrt.org>. Changes: * DTS support, * New gpio API (gpiod_*). Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> (cherry-picked from commit 7b8931678c36c8d8c333b446258a653b1358bf70)
* ltq-deu: Mark lantiq DEU brokenHauke Mehrtens2021-07-023-11/+6
| | | | | | | | | | | | | | | | | | | | | When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any more. It fails with this error message: daemon.err hostapd: nl80211: kernel reports: key addition failed daemon.err hostapd: Interface initialization failed OpenWrt uses the standard Linux crypto API in the wifi drivers now and this probably makes the system offload more crypto operations to special hardware like the Lantiq DEU. There is probably a bug in the DEU and these operations fail and then hostapd does not start the interface. Do not include the Lantiq DEU by default any more. Fixes: FS#3901 Fixes: 53b6783907f3 ("mac80211: remove patches stripping down crypto support") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Notupus <notpp46@gmail.com> (cherry-picked from commit 964863bb23999a1fae99b883053cc4f3c5c42b40)
* kernel: bump 5.4 to 5.4.128Hauke Mehrtens2021-06-2732-115/+77
| | | | | | | | | | | | | | | Manually rebased bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch Replaced with patch from Raspberry Pi kernel 5.10 patches mvebu/patches-5.4/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch Applied upstream All others updated automatically. Compile-tested on: ath79/generic, lantiq/xrx200, brcm27xx Runtime-tested on: ath79/generic, lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: Fix failsafe modeHauke Mehrtens2021-06-222-0/+19
| | | | | | | | | | | | | | | | The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is configured. Do not use the standard failsafe configuration for DSA accessing the default port directly, but configure a switch on the lan1 interface instead. This will add the VLAN ID 1 configuration to the switch: $ bridge vlan show port vlan-id lan1 1 PVID Egress Untagged switch 1 PVID Egress Untagged Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit b7ee0786b56d1088c195fe7c1cdb1ad7d20c9245)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-25 05:08:09 +0000