aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix the number of uarts for MT7688Furong Xu2017-02-162-4/+4
| | | | | | Same as MT7621 and MT7628, MT7688 allows up to 3 uarts Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: fix PWM pin mux conflict in dtsiFurong Xu2017-02-161-4/+0
| | | | | | | | | | | | | GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict [ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm [ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22 [ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux [ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back Keep PWM disabled. Signed-off-by: Furong Xu <xfr@outlook.com>
* kernel: update kernel 4.9 to version 4.9.10Hauke Mehrtens2017-02-164-7/+7
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: replace remaining instances of ralink, port-mapDaniel Golle2017-02-1511-11/+11
| | | | | | | | | | | | Some boards were apparently forgotten when ralink,portmap was renamed to mediatek,portmap -- probably because they used the long obsolete ralink,port-map attribute. If this commit breaks ethernet wan/lan assignment, this is because the port-map attribute wasn't actually parsed, you'll have to replace "wllll" by "llllw" in the dts file belonging to that board (and send a patch doing that!) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix mt7621 ethernet support for v4.9John Crispin2017-02-152-1/+8
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: export slic IRQ line in dwr-512Giuseppe Lippolis2017-02-151-0/+4
| | | | | | | | The DWR-512 embeds the hw slic device si3210. This device have the IRQ line attached to the gpio1. This patch export the gpio1 with proper name and parameters to the sysfs. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: revert faulty 4.4 config change from 9c242270907Felix Fietkau2017-02-141-9/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: Clean duplicated status property for Omega2 WMAC in dtsiFurong Xu2017-02-141-4/+0
| | | | | | At the tail of dtsi, wmac is enabled twice, clean the first one Signed-off-by: Furong Xu <xfr@outlook.com>
* ramips: fixed sms led polarity into dwr-512 DTGiuseppe Lippolis2017-02-141-1/+1
| | | | Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: WN3000RPv3: do not setup switchThibaut VARENE2017-02-141-1/+1
| | | | | | | | | The WN3000RPv3 is a repeater with a single ethernet port. Setting up the switch, even to disable it, is unnecessary and possibly confusing. Configure LAN as eth0 instead. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add v4.9 supportJohn Crispin2017-02-1478-3/+23061
| | | | | | NAND support is missing Signed-off-by: John Crispin <john@phrozen.org>
* ramips: added image size into dwr-512 DTGiuseppe Lippolis2017-02-131-0/+1
| | | | Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: correct switch configuration for Newifi D1Chuanhong Guo2017-02-131-4/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix AR670W partition alignmentClaudio Leite2017-02-091-1/+1
| | | | | | | mtdsplit_lzma requires that the rootfs be aligned to a block boundary. Pad the kernel partition to make this so. Signed-off-by: Claudio Leite <leitec@gmail.com>
* kernel: update kernel 4.4 to version 4.4.47Stijn Tintel2017-02-061-1/+1
| | | | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken, except arc770 and arch38 due to broken toolchain. Runtime-tested on ar71xx, octeon, ramips and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for Sanlinking D240Kristian Evensen2017-02-057-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* build: centralize fakeroot codeJoseph C. Lehner2017-02-042-2/+2
| | | | | | | | | | | | | This patch moves the fakeroot code required by some devices to `image-commands.mk`. Create the fakeroot on the fly by using the undocumented -s (skip copy) parameter of mkimage. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy rootfs for mkimage] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Airlink AR725W device titleMathias Kresin2017-02-041-1/+1
| | | | | | Gemtek is the ODM but the board was sold by Airlink101. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Airlink AR725W factory image buildMathias Kresin2017-02-041-2/+5
| | | | | | | | | | | | | The factory image can't be bigger than 3328 KByte. If the image is bigger than that, the gemtek-header tool throws an error and breaks the build. Make sure the output file to which the gemtek header should be added exists and wasn't removed during the check-size step because of it size. This will prevent hard errors in case the factory image is to big similar to what is done for sysupgrade images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* rt5350: added pcm interface in .dtsiGiuseppe Lippolis2017-02-031-0/+13
| | | | | | | | Added the missing audio pcm interface in the .dtsi file for the rt5350 device. The update has been verified from the data get from the datasheet and is very similar to the mt7620a.dtsi Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* generic: rtl8366rb: fix compatible stringMathias Kresin2017-02-032-2/+2
| | | | | | | Use a vendor prefix as it has to be for all not core driver. Update the compatible string in the device tree files accordingly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Sercomm NA930 compatible stringMathias Kresin2017-02-031-1/+1
| | | | | | | The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use the eval board compatible string. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove Planex CS-QR10 sound device tree nodeMathias Kresin2017-02-031-11/+0
| | | | | | | | The comptible string is neither added by any LEDE patch nor exists in in the kernel. Drop the sound node which was obviously added accidentally with 9195d8da ("ramips: DTS rework"). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: cleanup SPI flash device tree properties usageMathias Kresin2017-02-02110-116/+6
| | | | | | | | | Use only the jedec,spi-nor compatible string. Everything else either never worked or is only support to keep compatibility. Remove the linux,modalias property. It is obsolete since kernel 4.4. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to F5D8235 V1 (rt288x)Tobias Wolf2017-02-023-3/+6
| | | | | | | | | | This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and configures the F5D8235 V1 target to use append-dtb for kernel creation instead of OWRTDTB. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de> [Jo-Philipp Wich: rewrap commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to arch/mips/ralinkTobias Wolf2017-02-021-0/+28
| | | | | | | | | | This commit introduces CONFIG_MIPS_APPENDED_RAW_DTB as an alternative to OWRTDTB. Both solutions can be used concurrently until all board configurations have been changed. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de> [Jo-Philipp Wich: rewrap commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mt76: update to the latest versionFelix Fietkau2017-02-0131-49/+35
| | | | | | | | Uses upstream code to parse DT supported band/frequency information. Update existing .dts files to the new format and remove unnecessary overrides. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: remove DT pcie nodes for GL-MT300A/NFelix Fietkau2017-02-012-26/+0
| | | | | | These devices don't have a secondary wifi chip Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for Buffalo WCR-1166DSFUKAUMI Naoki2017-01-319-15/+245
| | | | | | | | | | | | | | | | | | | | | Buffalo WCR-1166DS is a small wireless router with - MT7628AN + MT7612E - 64MiB DDR2 SDRAM - 16MiB SPI flash - 2T2R 11ac/a/b/g/n Wi-Fi - 2x 10/100M ethernet switch - 8x programmable LED - 3x button - UART pad on PCB (J2: 3.3V, GND, TX, RX) factory image can be installed via stock web UI. due to the "dual image" function in the bootloader, the second half of the SPI flash ("firmware2" partition) cannot be used as a part of the file system. Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ramips: add missing DTS pcie node for WSR-600Felix Fietkau2017-01-311-0/+21
| | | | | | Enables PCI bus and support for the MT7603 and RT5592 chips Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Kernel: bump to 4.4.44Stijn Segers2017-01-271-4/+4
| | | | | | | | Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64. .44 has been run-tested on the 17.01 branch here on ar71xx and mt7621. Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ramips: cleanup mt7620 Netgear image codeJoseph C. Lehner2017-01-273-17/+9
| | | | | | | 1. Reuse functions defined in `image-commands.mk` 2. Rename fakeroot image Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: enable rlt8366s Green Feature for F5D8235 V1Tobias Wolf2017-01-271-0/+2
| | | | | | Enable the green feature for the board by default. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: add rlt8366s initvals to the F5D8235 V1 DTSTobias Wolf2017-01-271-0/+39
| | | | | | | | | | Before this change only port 4 of F5D8235 V1 worked at 1000Mpbs. Comparing the current driver with the GPL_BELKIN_F5D8235-4_v1000 v1.01.24 sources showed that additional steps are required to set-up the rlt8366s switch correctly. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb powerVitaly Chekryzhev2017-01-262-0/+22
| | | | | | Export gpio usb to allow power management of USB port. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Viva: align factory imagesVitaly Chekryzhev2017-01-261-1/+1
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Viva: export gpio usb powerVitaly Chekryzhev2017-01-261-0/+11
| | | | | | Export gpio usb to allow power management of USB port. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add ip17xx support to WLI-TX4-AG300NYo Abe2017-01-261-0/+1
| | | | | | | | | ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which should be included by default. Signed-off-by: Yo Abe <abe.geel@gmail.com> [Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: fix EX2700 wireless macJoseph C. Lehner2017-01-261-13/+11
| | | | | | | | On some EX2700 devices, the MAC address from the eeprom data differs from the actual MAC address. Fix that, and cleanup the DTS file while we're at it. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* build: remove mips16 feature flag from target makefilesFelix Fietkau2017-01-241-1/+1
| | | | | | | It can be implicitly derived from the MIPS32 revision support in the kernel configuration Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips/rt288x: switch CPU_TYPE to 24kcFelix Fietkau2017-01-241-1/+1
| | | | | | | | | | | While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2 architecture just like the 24Kc, so the instruction set should be 100% compatible. Switching it to 24kc allows it to share the package architecture with a lot of other targets instead of creating a special case, saving buildbot resources. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ZyXEL Keenetic series update wan macVitaly Chekryzhev2017-01-201-1/+3
| | | | Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: ZyXEL Keenetic Omni align factory imagesVitaly Chekryzhev2017-01-201-2/+2
| | | | | | ZyXEL web-flasher requires squashfs to be aligned to 64kb. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: correct keenetic-series switch indexVitaly Chekryzhev2017-01-201-1/+1
| | | | | | Fix switch name typo Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: add support for Netgear WN3000RPv3Thibaut VARENE2017-01-187-2/+163
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: fix mac address of miwifi-miniBangLang Huang2017-01-182-1/+5
| | | | | | | For the miwifi-mini, the offset of ethernet mac should be 0x28 which you can easyily dump from 'Factory' partition. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: simplify EX2700 network configJoseph C. Lehner2017-01-181-2/+2
| | | | | | Don't create a vlan for the Netgear EX2700's only Ethernet port. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: Add back sdhci-mt7620 driver to default configRosen Penev2017-01-181-4/+4
| | | | | | The driver no longer causes kernel panics and CPU hangs. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add back the i2c-mt7621 moduleJohn Crispin2017-01-151-0/+16
| | | | | | mt7628/88 are still using this module. Signed-off-by: John Crispin <john@phrozen.org>
* ramips: Added Onion Omega2 and Omega2+Lazar Demin2017-01-158-0/+249
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 02:05:31 +0000