aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt76x8
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-08-091-1/+3
| | | | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com> (cherry picked from commit 1a8c74da709190e5157af9f5c2502b600f6273bb) Signed-off-by: Tom Herbers <freifunk@tomherbers.de>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-271-0/+2
| | | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 539e60539a2fde6531bd179c94bb9c7f8f490f2b)
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-191-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com> (cherry picked from commit a4bf562aa71ad1e3dcffa392b79110d803a93f11)
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-191-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit bb505d82add5636da891bb97fdabc57947280e88)
* ramips: add support for Asus RT-AC1200Ray Wang2022-03-091-26/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: switch parser of trx for mt76x8 subtargetINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | | | | This patch enable parser_trx and disable mtdsplit_trx for mt76x8 subtarget. The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget and the parser need to be switched to parser_trx to use the custom magic number in the header for WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update MAC address configuration for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-2/+2
| | | | | | | | This patch converts MAC address configuration of Buffalo WCR-1166DS in 02_network to use the generic function of OpenWrt. And also, add label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: correct vendor name for COMFAST/JoowinRodrigo Araujo2022-01-221-7/+7
| | | | | | | | | | | | | | | | When Joowin WR758AC V1 and V2 devices were added, they should have been added with the primary manufacturer name which is COMFAST, since Joowin is just an alternate vendor name on some coutries or stores. Fix this by changing the the vendor name on the respective files and set Joowin as ALT0 variants while ensuring compatibility for early users. Also adjust the model names to better follow the naming rules. As a side effect, fix mt76x8 network script which was left incorrectly unsorted on the case block conditions. Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2") Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: add support for Joowin WR758AC V1 and V2Rodrigo Araujo2022-01-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2 devices. Both have the same wall AP/repeater form factor and differ only in the 5Ghz chipset (V1 has MT7662, V2 has MT7663). OpenWrt developers forum page: https://forum.openwrt.org/t/87355 Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB DDR2 - 2.4 GHz: 802.11b/g/n (MT7603) - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663) - Antennas: 4x external single band antennas - LAN: 1x 10/100M - LED: Wifi 3x blue. Programmable - Button: WPS MAC addresses as verified by OEM firmware: use address source LAN *:83 factory 0xe000 2g *:85 factory 0x4 5g *:86 factory 0x8004 How to install: 1- Setup a TFTP server on a machine with IP address 192.168.1.10/24 2- Name the image as `firmware_auto.bin` and place it on the root of the TFTP server 3- Connect the device via Ethernet, it should pick and flash the image Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-171-1/+0
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: remove Linux 5.4 supportRui Salvaterra2021-12-151-192/+0
| | | | | | We're at 5.10 stable, this can finally go. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: mt76x8: tidy up 02_networkSungbo Eo2021-12-121-8/+5
| | | | | | | * fix alphabetic sorting * consolidate duplicate cases Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix tl-mr3020-v3 switch topology to configure vlans via luciSergey V. Lobanov2021-12-041-1/+4
| | | | | | | | | | Currently it is not possible to configure VLANs via LUCI on tplink tl-mr3020-v3. This patch fixes switch topology for the LUCI interface. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in> [copied commit message from github PR] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Wavlink WL-WN576A2Thomas Aldrian2021-11-202-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles repeater / router. It is also sold under the name SilverCrest SWV 733 B1. Device specs: - CPU: MediaTek MT7628AN - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - 5 GHz: a/n/ac MT7610EN - Buttons: WPS, reset, sliding switch (ap/repeater) - LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS Flashing: U-Boot launches a TFTP client if WPS button is held during boot. - Server IP: 192.168.10.100 - Firmware file name: firmware.bin Device will reboot automatically. First boot takes about 90s. Coelner (waenger@gmail.com) is the original author, but I have made some fixes. He does not wish to sign off using his real name. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* ramips: add support for Xiaomi MiWifi 3CEduardo Santos2021-10-311-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE305 v3Michal Kozuch2021-10-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specs (same as in v1): - MT7628AN (575 MHz) - 64MB RAM - 8MB of flash (SPI NOR) - 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan) - 1x 2.4GHz wifi (MT7628AN) - 1x 5Ghz wifi (MT7612E) - 4x LEDs (5 GPIO-controlled) - 1x reset button - 1x WPS button The only and important difference between v1 & v3 is in flash memory layout, so pls don't interchange these 2 builds! Installation through web-ui (on OEM factory firmware): 1. Visit http://tplinkrepeater.net or the configured IP address of your RE305 v3 (default 192.168.0.254). 2. Log in with the password you've set during initial setup of the RE305 (there is no default password). 3. Go to Settings -> System Tools -> Firmware upgrade 4. Click Browse and select the OpenWRT image with factory.bin suffix (not sysupgrade.bin) 5. A window with a progress bar will appear. Wait until it completes. 6. The RE305 will reboot into OpenWRT and serve DHCP requests on the ethernet port. 7. Connect an RJ45 cable from the RE305 to your computer and access LuCI at http://192.168.1.1/ to configure (or use ssh). Disassembly: Just unscrew 4 screws in the corners & take off the back cover. Serial is exposed to the right side of the main board (in the middle) and marked with TX/RX/3V3/GND, but the holes are filled with solder. Installation through serial: 1. connect trough serial (1n8, baudrate=57600) 2. setup the TFTP server and connect it via ethernet (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc) 3. boot from a initramfs image first (choose 1 in the bootloader options) 4. test it a bit with that, then proceed to run sysupgrade build MAC addresses as verified by OEM firmware: use OpenWrt address reference LAN eth0 *:d2 label 2g wlan0 *:d1 label - 1 5g wlan1 *:d0 label - 2 The label MAC address can be found in config 0x2008. Signed-off-by: Michal Kozuch <servitkar@gmail.com> [redistribute WLAN node properties between DTS/DTSI, remove compatible on DTSI, fix indent/wrapping, split out firmware-utils change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: minew g1-c: use default static address for lan instead of dhcpAlexander Couzens2021-08-311-5/+1
| | | | | | | | | As Adrian Schmutzler suggested on github [1] the device should follow the default behaviour on ethernet using a static address instead using dhcp. [1] https://github.com/openwrt/openwrt/commit/8d497b65704f62294a4bbc0e1f5aa4eb1dbf9e24 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for D-Link DAP-1325-A1Giovanni Cascione2021-08-252-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300) Specifications: - SoC: 580Mhz MT7628NN - RAM: 64MB, DDR2 SDRAM - Storage: 8MB, SPI (W25Q64JVSSIQ) - Ethernet: 1x 10/100 LAN port - WIFI: 2.4 GHz 802.11bgn - LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x) - Buttons: Reset, WPS - UART: Serial console (57600, 8n1) Row of 4 holes near LAN port, starting from square hole: 3.3V, TX,RX,GND - FCC ID: fccid.io/KA2AP1325A1/ Installation: Failsafe UI Firmware can be uploaded with Failsafe UI web page: - turn device off - press and hold reset button - turn device on - keep holding reset until red wifi strength led turns on (ab. 10sec) - connect to device through LAN port PC must be configured with static ip (192.168.0.x) - connect to 192.168.0.50 - select image to be flashed and upload. Device will reboot after successful update Serial port/TFTP server - Connect through serial connectors on PCB (e.g. with teraterm) - Set up a TFTP server, and connect through LAN with static IP - Put image file in the root of the server - Boot the device and select '2' at U-Boot startup - Set device IP, server IP and image file name - Start upload and flash Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com> [fix whitespaces in DTS, convert to nvmem, add mtd-eeprom] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Motorola MWR03Shiji Yang2021-08-251-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7628AN + MT7612E * ROM: 8 MiB Flash * RAM: 64 MiB DDR2 * WAN: 10/100M *1 * LAN: 10/100M *3 * Button: Reset *1 * LEDs: orange *1, white *1 * Antennas: 2.4 GHz *2 + 5 GHz *2 * TTL Baudrate: 57600 * TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100 MAC addresses as verified by OEM firmware: use address source 2g *:d8 factory 0x0004 (label) 5g *:d9 factory 0x8004 LAN *:d7 factory $label -1 WAN *:da factory $label +2 Installation (TFTP + U-Boot): * Connect device with a TTL cable and open a serial session by PuTTY. * Press "2" when booting to select "Load system code then write to Flash via TFTP". * Configure the IP of local host server. * Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix DTS line endings, fix label MAC address, adjust status LED names, convert mtd-mac-address-increment to mac-address-increment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Onion Omega 2(+)Adrian Schmutzler2021-08-211-4/+6
| | | | | | | | | | Thanks to a hint from Michael Siegenthaler in 4b4fa2f9fed7 ("ramips: fix ethernet MAC address on Omega2"), the label MAC address of the Onion Omega 2(+) can be set based on its documentation [1]. [1] https://docs.onion.io/omega2-docs/mac-address.html Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: add various missing config symbolsDavid Bauer2021-08-102-0/+2
| | | | | | Fixes commit 91a52f22a13d ("treewide: backport support for nvmem on non platform devices") Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix missing NVMEM subsystemDavid Bauer2021-07-212-0/+2
| | | | | | | | | | | | MAC address retrieval was switched to more generic upstream (5.13) NVMEM based solution in commit 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") , but NVMEM subsystem wasn't enabled in the kernel, so fix it now. References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801 Fixes: 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
* ramips: add support for minew g1-cAlexander Couzens2021-07-051-0/+5
| | | | | | | | | | | | | | | | | | | | | | The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add AW9523 I2C GPIO expander driverDavid Bauer2021-06-272-0/+2
| | | | | | | | | | | | | | This adds a driver for the AW9523 I2C GPIO expander. This driver is required to make LEDs as well as buttons on the Tenbay T-MB5EU-V01 work. This driver already had several upstream iterations. I'm working to push this driver to mainline. Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287 Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix Ethernet random MAC address for HILINK HLK-7628NLiu Yu2021-06-091-4/+1
| | | | | | | | | | | | | | | | | | Set the ethernet address from flash. MAC addresses as verified by OEM firmware: use interface source 2g wlan0 factory 0x04 (label) LAN eth0.1 factory 0x28 (label+1) WAN eth0.2 factory 0x2e (label+2) Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N") Signed-off-by: Liu Yu <f78fk@live.com> [drop old MAC address setup from 02_network, cut out state_default changes, face-lift commit message, add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Wavlink WL-WN578A2Thomas Aldrian2021-05-282-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-212-4/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: 5.10: refresh configsIlya Lipnitskiy2021-03-061-4/+4
| | | | | | | | Run-tested on Ubiquiti EdgeRouter X. Compile tested on all other subtargets. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: copy config-5.4 to config-5.10Ilya Lipnitskiy2021-03-061-0/+191
| | | | | | Strict copy, no changes made. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* Revert "ramips: add support for kernel 5.10"Adrian Schmutzler2021-03-061-191/+0
| | | | | | | | | This reverts commit b4aad29a1d7ad77d67073c1c54b28c429c64ed9b. This was accidentally folded into a single commit. Remove it and apply it properly again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for kernel 5.10Ilya Lipnitskiy2021-03-051-0/+191
| | | | | | | | | | | | | | | | | | | | | | | | | Enable testing kernel. Delete upstreamed patches: 0098-disable_cm.patch can be dropped, upstream fixed CM handling. Fix compile errors by using new kernel APIs. Fix fuzz by manually editing patches to ensure the code goes in the right place. For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit a307593a6 to keep the OpenWrt ralink driver operational. Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693 and #3952. Rename patches to follow the 3-digit classification from the OpenWrt Developer Guide. Run automatic quilt refresh. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: 5.4: refresh configsIlya Lipnitskiy2021-03-051-54/+3
| | | | | | Automatic refresh by running make kernel_oldconfig on each target. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: add support for ELECOM WRC-1167FSINAGAKI Hiroshi2021-02-112-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Hi-Link HLK-7688AEwan Parker2021-02-052-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7688AN - RAM: 128 MB - Flash: 32 MB - Ethernet: 5x 10/100 (1x WAN, 4x LAN) - Wireless: built in 2.4GHz (bgn) - USB: 1x USB 2.0 port - Buttons: 1x Reset - LEDs: 1x (WiFi) Flash instructions: - Configure TFTP server with IP address 10.10.10.3 - Name the firmware file as firmware.bin - Connect any Ethernet port to the TFTP server's LAN - Choose option 2 in U-Boot - Alternatively choose option 7 to upload firmware to the built-in web server MAC addresses as verified by OEM firmware: use address source 2g *:XX factory 0x4 LAN *:XX+1 factory 0x28 WAN *:XX+1 factory 0x2e Notes: This board is ostensibly a module containing the MediaTek MT7688AN SoC, 128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in IoT Gateway Mode or IoT Device Mode. From some vendors the U-Boot that comes installed operates on UART 2 which is inaccessible in gateway mode and operates unreliably in the Linux kernel when using more than 64 MB of RAM. For those, updating U-Boot is recommended. Signed-off-by: Ewan Parker <ewan@ewan.cc> [add WLAN to 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove generic profilesAdrian Schmutzler2021-01-271-17/+0
| | | | | | | | | | | | | On a platform with many very different devices, like found on ramips, the generic profiles seem like remnants of the past that do not have a real use anymore. Remove them to have one thing less to maintain. Actually, rt288x didn't have a default profile in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ramips: use full names for Xiaomi Mi Router devicesAdrian Schmutzler2020-12-081-3/+3
| | | | | | | | | | This aligns the device/image names of the older Xiaomi Mi Router devices with their "friendly" model and DEVICE_MODEL properties. This also reintroduces consistency with the newer devices already following that scheme. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Router 4CAtaberk Özen2020-11-252-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi's Mi Router 4C device. Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LEDs: 2x yellow/blue. Programmable (labelled as power on case) - Non-programmable (shows WAN activity) - Button: Reset How to install: 1- Use OpenWRTInvasion to gain telnet and ftp access. 2- Push openwrt firmware to /tmp/ using ftp. 3- Connect to router using telnet. (IP: 192.168.31.1 - Username: root - No password) 4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into the router.. 5- It takes around 2 minutes. After that router will restart itself to OpenWrt. Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com> [wrap commit message, bump PKG_RELEASE for uboot-envtools, remove dts-v1 from DTS, fix LED labels] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link MR6400 v5Filip Moc2020-11-252-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are: - smaller form factor - different LED GPIOs - different switch connections You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v5.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for TP-Link MR6400 v4Filip Moc2020-11-232-0/+8
| | | | | | | | | | | | | | | | | | | | | | | You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v4.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* ramips: add support for the Hak5 WiFi Pineapple Mark 7Marc Egerton2020-11-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WiFi Pineapple Mark 7, a wireless penetration testing tool. Specifications: * SoC: MediaTek MT7628 (580MHz) * RAM: 256MiB (DDR2) * Storage 1: 32MiB NOR (SPI) * Storage 2: 2GB eMMC * Wireless 1: 802.11b/g/n 2.4GHz (Built In) * Wireless 2: 802.11b/g/n 2.4GHz (MT7601) * Wireless 3: 802.11b/g/n 2.4GHz (MT7601) * USB: 1x USB Type-A 2.0 Host Port * Ethernet: 1x USB Type-C AX88772C Ethernet * UART: 57600 8N1 on PCB * Inputs: 1x Reset Button * Outputs: 1x RGB LED * FCCID: 2AA52MK7 Flash Instructions: Original firmware is based on OpenWRT. Use sysupgrade via SSH to flash. Signed-off-by: Marc Egerton <foxtrot@realloc.me> [pepe2k@gmail.com: set only required/used gpio groups to gpio function] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for TP-Link RE200 v4Richard Fröhning2020-10-202-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2/v3. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button - UART connection holes on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:8E 2.4G: *:8D 5G : *:8C MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [removed empty line, fix commit message formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: remove set_wifi_led function in 01_ledsAdrian Schmutzler2020-10-021-12/+8
| | | | | | | | | | | | | | | | | | | While we mostly use the ucidef_set_led_* functions directly in 01_leds we still have the set_wifi_led function in parallel for several old devices. This is not only inconsistent with the other definitions, it also links to the wlan0 interface instead of using a phy trigger which would be independent of the interface name (and is used for all newer devices anyway). Apart from that, the standard names "wifi" and "wifi-led" are not very helpful in a world with different radio bands either. Thus, this patch removes the set_wifi_led function and puts the relevant commands into the cases explicitly. This makes the mechanism used more evident and will hopefully lead to some future improvements or at least prevent some copy-pasting of the old setups. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove option to set WiFi LED via aliasesAdrian Schmutzler2020-10-021-4/+5
| | | | | | | | | | | | | In ramips, it's not common to use an alias for specifying the WiFi LED; actually only one device uses this mechanism (TL-WR841N v14). Particularly since the WiFi LEDs are typically distinguished between 2.4G and 5G etc. it is also not very useful for this target. Thus, this patch removes the setup lines for this mechanism and converts the TL-WR841N v14 to the normal setup. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove model name from LED labelsAdrian Schmutzler2020-10-022-88/+59
| | | | | | | | | | | | | | | | | Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link TL-WR850N v2Andrew Freeman2020-08-272-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR850N v2. This device is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13. Specifications: SOC: MediaTek MT7628NN Flash: 8 MiB SPI RAM: 64 MiB WLAN: MediaTek MT7628NN Ethernet: 5 ports (100M) Installation Using the integrated tftp capability of the router: 1. Turn off the router. 2. Connect pc to one of the router LAN ports. 3. Set your PC IPv4 address to 192.168.0.66/24. 4. Run any TFTP server on the PC. 5. Put the recovery firmware on the root directory of TFTP server and name the file tp_recovery.bin 6. Start the router by pressing power button while holding the WPS/Reset button (or both WPS/Reset and WIFI buttons) 7. Router connects to your PC with IPv4 address 192.168.0.2, downloads the firmware, installs it and reboots. LEDs are flashing. Now you have OpenWrt installed. 8. Change your IPv4 PC address to something in 192.168.1.0/24 network or use DHCP to get an address from your OpenWrt router. 9. Done! You can login to your router via ssh. Forum link: https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899 Signed-off-by: Andrew Freeman <labz56@gmail.com> [squash an tidy up commits, sort nodes] Signed-off-by: Darsh Patel <darshkpatel@gmail.com> [minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: tidy up MAC address setup for Linkit Smart and Omega2Adrian Schmutzler2020-08-061-6/+0
| | | | | | | | | | | | | | | | | | | | Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and have their port set to LAN by default. Setting up a WAN MAC address for them doesn't make any sense, as no wan interface will be created in uci config. Despite, these devices also set lan_mac in 02_network, although mtd-mac-address sets a different address for the ethernet interface in DTS. Clean this up by moving the lan_mac value into DTS and dropping the entries in 02_network completely. That way, the effective address on the LAN interface should stay the same, but we get rid of the extra (re)assignments. As I don't have access to the devices, this does not tell anything about whether 0x2e is actually a good choice, it just preserves the existing assignment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: WizFi630S use macs from factory partionTobias Welz2020-08-061-2/+5
| | | | | | | | | | | | | | | | | | | | WIZnet WizFi630s has three mac addresses in the factory partition: 0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac. All three macadresses are sequential series of addresses. This is making use of them. While at it, also add the label MAC address to 02_network. MAC addresses as verified by OEM firmware: use interface source WLAN ra0 factory 0x04 (label) WAN eth0.2 factory 0x28 (label + 1) LAN eth0.1 factory 0x2e (label + 2) Signed-off-by: Tobias Welz <tw@wiznet.eu> [fix sorting in 02_network, commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>