aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-08-282-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea) [switch to mtd-mac-address instead of nvmem-cells]
* ramips: Add support for SERCOMM NA502Andreas Böhler2021-06-102-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit a3d8c1295ed9eeceabd78ab86e73b151ae2868a9)
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-105-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b232680f847f4ea8d058849a51dedebb8e398a01)
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-102-15/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com> (cherry picked from commit 6d23e474ad9d0eba935696c66db4fb6e2037bb72)
* ramips: add support for Linksys E5600Aashish Kulkarni2021-06-105-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Linksys EA7300 v1/ v2. Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: 128M DDR3-1600 * Flash: 128M NAND * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz) * Antennae: 2 internal fixed in the casing and 2 on the PCB * LEDs: Blue (x4 Ethernet) Blue+Orange (x2 Power + WPS and Internet) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This device has 2 partitions for the firmware called firmware and alt_firmware. To successfully flash and boot the device, the device should have been running from alt_firmware partition. To get the device booted through alt_firmware partition, download the OEM firmware from Linksys website and upgrade the firmware from web GUI. Once this is done, flash the OpenWrt Factory firmware from web GUI. Reverting to factory firmware: 1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of the following: Press the "wps" button as soon as power LED turns on when booting. (OR) Hard-reset the router consecutively three times to force it to boot from 'alt_firmware'. 2. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com> [fix hanging indents and wrap to 74 characters per line, add kmod-mt7663-firmware-sta package for 5GHz STA mode to work, remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk, set default-state "on" for power LED] Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com> [move check-size before append-metadata, remove trailing whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Sannihith Kinnera <digislayer@protonmail.com> (cherry picked from commit 251c995cbb1ea5ad1de14775312c2bd19ed10439)
* ramips: add support for JCG Q20Chukun Pan2021-06-103-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit 57cb387cfeee2a07902a2f1383ca471ef47265f3)
* ramips: add support for cudy WR2100Leon M. George2021-06-101-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications SoC: MT7621 CPU: 880 MHz Flash: 16 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac MT7603E / MT7615E Ethernet: 5x Gbit ports Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. R4 & R5 need to be shorted (0-100Ω) for the UART to work. Signed-off-by: Leon M. George <leon@georgemail.eu> [remove non-required switch-port node - remove trgmii phy-mode] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 3501db9b9b4a71ae52c539b46af817783c327866)
* ramips: add support for TP-Link Archer C6U v1 (EU)Georgi Vlaev2021-06-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6U v1 (EU). The device is also known in some market as Archer C6 v3. This patch supports only Archer C6U v1 (EU). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (Winbond 25Q128) * WiFi 5GHz: Mediatek MT7613BEN (2x2:2) * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) * Ethernet: MT7630, 5x 1000Base-T. * LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB * Buttons: Reset, WPS. * UART: Serial console (115200 8n1), J1(GND:3) * USB: One USB2 port. Installation: ------------ Install the OpenWrt factory image for C6U is from the TP-Link web interface. 1) Go to "Advanced/System Tools/Firmware Update". 2) Click "Browse" and upload the OpenWrt factory image: openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. 3) Click the "Upgrade" button, and select "Yes" when prompted. Recovery to stock firmware: -------------------------- The C6U bootloader has a failsafe mode that provides a web interface (running at 192.168.0.1) for reverting back to the stock TP-Link firmware. The failsafe interface is triggered from the serial console or on failed kernel boot. Unfortunately, there's no key combination that enables the failsafe mode. This gives us two options for recovery: 1) Recover using the serial console (J1 header). The recovery interface can be selected by hitting 'x' when prompted on boot. 2) Trigger the bootloader failsafe mode. A more dangerous option is force the bootloader into recovery mode by erasing the OpenWrt partition from the OpenWrt's shell - e.g "mtd erase firmware". Please be careful, since erasing the wrong partition can brick your device. MAC addresses: ------------- OEM firmware configuration: D8:07:B6:xx:xx:83 : 5G D8:07:B6:xx:xx:84 : LAN (label) D8:07:B6:xx:xx:84 : 2.4G D8:07:B6:xx:xx:85 : WAN Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com> (cherry picked from commit a46ad596a3e076599f38a4132b5d6dfee8a3102a)
* ramips: add support for TP-Link Archer A6 v3Vinay Patil2021-06-101-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer A6 v3 The router is sold in US and India with FCC ID TE7A6V3 Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated from serial console only. Press 'x' while u-boot is starting Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Thanks to: Frankis for Randmon MAC address fix. Signed-off-by: Vinay Patil <post2vinay@gmail.com> [remove superfluous factory image definition, whitespacing] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f8f8935adb2be1ebce46a8d7058c76a8d3a9bd89)
* ramips: mt7621: Add support for ZyXEL NR7101Bjørn Mork2021-06-104-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE with integrated directional 5G/LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E - Switch: 1 LAN port (Gigabiti) - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC - SIM: 2 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/yellow under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to 5G/LTE bridge or router. The Wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover, the WLAN button and 12 screws holding the back plate and antenna cover together. The GPS antenna is fixed to the cover, so be careful with the cable. Remove 4 screws fixing the antenna board to the main board, again being careful with the cables. A bluetooth TTL adapter is recommended for permanent console access, to keep the router water and dustproof. The 3.3V pin is able to power such an adapter. MAC addresses: OpenWrt OEM Address Found as lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex) wwan0 usb0 random WARNING!! ISP managed firmware might at any time update itself to a version where all known workarounds have been disabled. Never boot an ISP managed firmware with a SIM in any of the slots if you intend to use the router with OpenWrt. The bootloader lock can only be disabled with root access to running firmware. The flash chip is physically inaccessible without soldering. Installation from OEM web GUI: - Log in as "supervisor" on https://172.17.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Installation from OEM ssh: - Log in as "root" on 172.17.1.1 port 22022 - scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp - Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit - Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Copying OpenWrt to the recovery partition: - Verify that you are running a working OpenWrt recovery image from flash - ssh to root@192.168.1.1 and run: fw_setenv CheckBypass 0 mtd -r erase Kernel2 - Wait while the bootloader mirrors Image1 to Image2 NOTE: This should only be done after successfully booting the OpenWrt recovery image from the primary partition during installation. Do not do this after having sysupgraded OpenWrt! Reinstalling the recovery image on normal upgrades is not required or recommended. Installation from Z-Loader: - Halt boot by pressing Escape on console - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image NOTE: ATNR will write the recovery image to both primary and recovery partitions in one go. Booting from RAM: - Halt boot by pressing Escape on console - Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu - Press "4" to select "4: Entr boot command line interface." - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Load it using "tftpboot 0x88000000 initramfs-recovery.bin" - Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL header This method can also be used to RAM boot OEM firmware. The warning regarding OEM applies! Never boot an unknown OEM firmware, or any OEM firmware with a SIM in any slot. NOTE: U-Boot configuration is incomplete (on some devices?). You may have to configure a working mac address before running tftp using "setenv eth0addr <mac>" Unlocking the bootloader: If you are unebale to halt boot, then the bootloader is locked. The OEM firmware locks the bootloader on every boot by setting DebugFlag to 0. Setting it to 1 is therefore only temporary when OEM firmware is installed. - Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware - Run "fw_setenv DebugFlag 0x1" in OpenWrt NOTE: OpenWrt does this automatically on first boot if necessary NOTE2: Setting the flag to 0x1 avoids the reset to 0 in known OEM versions, but this might change. WARNING: Writing anything to flash while the bootloader is locked is considered extremely risky. Errors might cause a permanent brick! Enabling management access from LAN: Temporary workaround to allow installing OpenWrt if OEM firmware has disabled LAN management: - Connect to console - Log in as "root" - Run "iptables -I INPUT -i br0 -j ACCEPT" Notes on the OEM/bootloader dual partition scheme The dual partition scheme on this device uses Image2 as a recovery image only. The device will always boot from Image1, but the bootloader might copy Image2 to Image1 under specific conditions. This scheme prevents repurposing of the space occupied by Image2 in any useful way. Validation of primary and recovery images is controlled by the variables CheckBypass, Image1Stable, and Image1Try. The bootloader sets CheckBypass to 0 and reboots if Image1 fails validation. If CheckBypass is 0 and Image1 is invalid then Image2 is copied to Image1. If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to Image2. If CheckBypass is 1 then all tests are skipped and Image1 is booted unconditionally. CheckBypass is set to 1 after each successful validation of Image1. Image1Try is incremented if Image1Stable is 0, and Image2 is copied to Image1 if Image1Try is 3 or larger. But the bootloader only tests Image1Try if CheckBypass is 0, which is impossible unless the booted image sets it to 0 before failing. The system is therefore not resilient against runtime errors like failure to mount the rootfs, unless the kernel image sets CheckBypass to 0 before failing. This is not yet implemented in OpenWrt. Setting Image1Stable to 1 prevents the bootloader from updating Image1Try on every boot, saving unnecessary writes to the environment partition. Keeping an OpenWrt initramfs recovery as Image2 is recommended primarily to avoid unwanted OEM firmware boots on failure. Ref the warning above. It enables console-less recovery in case of some failures to boot from Image1. Signed-off-by: Bjørn Mork <bjorn@mork.no> Tested-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 2449a632084b29632605e5a79ce5d73028eb15dd)
* ramips: mt7621: enable SX150x driverSander Vanheule2021-02-241-0/+1
| | | | | | | | | | | | | | | | | The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO expander controlling the device LEDs. This expander was initially supported on 4.14, but support was lost in the transition to 5.4. Since this driver cannot be built as a kernel module, enable it in the kernel config for all mt7621 devices. Run-tested on a Netgear R6800. Cc: Stijn Segers <foss@volatilesystems.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> (cherry picked from commit 773949c152f7378a303919e790210113012fea04)
* ramips: mt7621: add TP-Link EAP235-Wall supportSander Vanheule2021-02-191-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access point with four gigabit ethernet ports. When connecting to the device's serial port, it is strongly advised to use an isolated UART adapter. This prevents linking different power domains created by the PoE power supply, which may damage your devices. The device's U-Boot supports saving modified environments with `saveenv`. However, there is no u-boot-env partition, and saving modifications will cause the partition table to be overwritten. This is not an issue for running OpenWrt, but will prevent the vendor FW from functioning properly. Device specifications: * SoC: MT7621DAT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (MT7603EN): b/g/n, 2x2 * Wireless 5GHz (MT7613BEN): a/n/ac, 2x2 * Ethernet: 4× GbE * Back side: ETH0, PoE PD port * Bottom side: ETH1, ETH2, ETH3 * Single white device LED * LED button, reset button (available for failsafe) * PoE pass-through on port ETH3 (enabled with GPIO) Datasheet of the flash chip specifies a maximum frequency of 33MHz, but that didn't work. 20MHz gives no errors with reading (flash dump) or writing (sysupgrade). Device mac addresses: Stock firmware uses the same MAC address for ethernet (on device label) and 2.4GHz wireless. The 5GHz wireless address is incremented by one. This address is stored in the 'info' ('default-mac') partition at an offset of 8 bytes. From OEM ifconfig: eth a4:2b:b0:...:88 ra0 a4:2b:b0:...:88 rai0 a4:2b:b0:...:89 Flashing instructions: * Enable SSH in the web interface, and SSH into the target device * run `cliclientd stopcs`, this should return "success" * upload the factory image via the web interface Debricking: U-boot can be interrupted during boot, serial console is 57600 baud, 8n1 This allows installing a sysupgrade image, or fixing the device in another way. * Access serial header from the side of the board, close to ETH3, pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3. * Interrupt bootloader by holding '4' during boot, which drops the bootloader into its shell * Change default 'serverip' and 'ipaddr' variables (optional) * Download initramfs with `tftpboot`, and boot image with `bootm` # tftpboot 84000000 openwrt-initramfs.bin # bootm Revert to stock: Using the tplink-safeloader utility from the firmware-utils package, TP-Link's firmware image can be converted to an OpenWrt-compatible sysupgrade image: $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \ -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin This can then be flashed using the OpenWrt sysupgrade interface. The image will appear to be incompatible and must be force flashed, without keeping the current configuration. Known issues: - DFS support is incomplete (known issue with MT7613) - MT7613 radio may stop responding when idling, reboot required. This was an issue with the ddc75ff704 version of mt76, but appears to have improved/disappeared with bc3963764d. Error notice example: [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout Hardware was kindly provided for porting by Stijn Segers. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 1e75909a35a2b361cdfdfcf18a26ad61271b174e)
* ramips: add support for JCG Y2Chukun Pan2021-02-092-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | JCG Y2 is an AC1300M router Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615) Ethernet: 10/100/1000 Mbps x5 LED: POWER, INTERNET, 2.4G, 5G Button: Reset Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page. MAC addresses map: 0x0004 *:c8 wlan2g/wlan5g/label 0xe000 *:c7 lan 0xe006 *:c6 wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: mt7621: use preferred logic in lib/upgrade/iodata.shAdrian Schmutzler2021-02-071-3/+3
| | | | | | | shellcheck recommends || and && over "-a" and "-o" because the latter are not well defined. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WN-DX1200GRINAGAKI Hiroshi2021-02-072-4/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : raw NAND 128 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7603E - 5 GHz : MediaTek MT7613BE - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/keys : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: 3.3V, TX, RX, NC, GND from triangle-mark - 57600n8 - Power : 12 VDC, 1 A Flash instruction using initramfs image: 1. Boot WN-DX1200GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with the squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - currently, mt7615e driver in mt76 doesn't fully support MT7613 (MT7663) wifi chip - the eeprom data in flash is not used by mt7615e driver and the driver reports the tx-power up to 3dBm - the correct MAC address for MT7613BE in eeprom data cannot be assigned to the phy - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" (called as "combo image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC") - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32" - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b) : kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs MAC addresses: LAN: 50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex)) WAN: 50:41:B9:xx:xx:0A (Factory, 0x1E006 (hex)) 2.4GHz: 50:41:B9:xx:xx:08 (Factory, 0x4 (hex)) 5GHz: 50:41:B9:xx:xx:09 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [add check whether dflag_offset is set] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ELECOM WRC-2533GHBK-IINAGAKI Hiroshi2021-01-291-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, RX, GND, TX from SoC side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-2533GHBK-I normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing MAC addresses: LAN : BC:5C:4C:xx:xx:89 (Config, ethaddr (text)) WAN : BC:5C:4C:xx:xx:88 (Config, wanaddr (text)) 2.4GHz : BC:5C:4C:xx:xx:8A (Factory, 0x4 (hex)) 5GHz : BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: remove generic profilesAdrian Schmutzler2021-01-271-19/+0
| | | | | | | | | | | | | On a platform with many very different devices, like found on ramips, the generic profiles seem like remnants of the past that do not have a real use anymore. Remove them to have one thing less to maintain. Actually, rt288x didn't have a default profile in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ramips: mt7621: add support for Xiaomi Mi Router 4Dmytro Oz2021-01-212-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for the RAM (256Mib→128Mib), LEDs and gpio (MiNet button). Specifications: Power: 12 VDC, 1 A Connector type: barrel CPU1: MediaTek MT7621A (880 MHz, 4 cores) FLA1: 128 MiB (ESMT F59L1G81MA) RAM1: 128 MiB (ESMT M15T1G1664A) WI1 chip1: MediaTek MT7603EN WI1 802dot11 protocols: bgn WI1 MIMO config: 2x2:2 WI1 antenna connector: U.FL WI2 chip1: MediaTek MT7612EN WI2 802dot11 protocols: an+ac WI2 MIMO config: 2x2:2 WI2 antenna connector: U.FL ETH chip1: MediaTek MT7621A Switch: MediaTek MT7621A UART Serial [o] TX [o] GND [o] RX [ ] VCC - Do not connect it MAC addresses as verified by OEM firmware: use address source LAN *:c2 factory 0xe000 (label) WAN *:c3 factory 0xe006 2g *:c4 factory 0x0000 5g *:c5 factory 0x8000 Flashing instructions: 1.Create a simple http server (nginx etc) 2.set uart enable To enable writing to the console, you must reset to factory settings Then you see uboot boot, press the keyboard 4 button (enter uboot command line) If it is not successful, repeat the above operation of restoring the factory settings. After entering the uboot command line, type: setenv uart_en 1 saveenv boot 3.use shell in uart cd /tmp wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1 mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0 nvram set flag_try_sys1_failed=1 nvram commit reboot 4.login to the router http://192.168.1.1/ Installation via Software exploit Find the instructions in the https://github.com/acecilia/OpenWRTInvasion Signed-off-by: Dmytro Oz <sequentiality@gmail.com> [commit message facelift, rebase onto shared DTSI/common device definition, bump uboot-envtools] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: refresh the kernel configRui Salvaterra2021-01-151-50/+4
| | | | | | | | The removed config symbols are already enabled by the generic kernel configuration (or by default), while the added ones are forcefully enabled by the specific architecture. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: add support for Ubiquiti UniFi 6 LiteDavid Bauer2021-01-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7621AT 256M DDR3 32M SPI-NOR MediaTek MT7603 2T2R 802.11n 2.4GHz MediaTek MT7915 2T2R 802.11ax 5GHz Not Working ----------- - Bluetooth (connected to UART3) UART ---- UART is located in the lower left corner of the board. Pinout is 0 - 3V3 (don't connect) 1 - RX 2 - TX 3 - GND Console is 115200 8N1. Boot ---- 1. Connect to the serial console and connect power. 2. Double-press ESC when prompted 3. Set the fdt address $ fdt addr $(fdtcontroladdr) 4. Remove the signature node from the control FDT $ fdt rm /signature 5. Transfer and boot the OpenWrt initramfs image to the device. Make sure to name the file C0A80114.img and have it reachable at 192.168.1.1/24 $ tftpboot; bootm Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Below are the original installation instructions prior to the discovery of "devmode=TRUE". They are not required for installation and are documentation only. The bootloader employs signature verification on the FIT image configurations. This way, booting unauthorized image without patching the bootloader is not possible. Manually configuring the bootcmd in the U-Boot envronment won't work, as this is restored to the default value if modified. The bootloader is made up of three different parts. 1. The SPL performing early board initialization and providing a XModem recovery in case the PBL is missing 2. The PBL being the primary U-Boot application and containing the control FDT. It is LZMA packed with a uImage header. 3. A Ubiquiti standalone U-Boot application providing the main boot routine as well as their recovery mechanism. In a perfect world, we would only replace the PBL, as the SPL does not perform checks on the PBLs integrity. However, as the PBL is in the same eraseblock as the SPL, we need to at least rewrite both. The bootloader will only verify integrity in case it has a "signature" node in it's control device-tree. Renaming the signature node to something else will prevent this from happening. Warning: These instructions are based on the firmware intially shipped with the device and potentially brick your device in a way it can only be recovered using a SPI flasher. Only (!) proceed if you understand this! 1. Extract the bootloader from the U-Boot partition using the OpenWrt initramfs image. 2. Split the bootloader into it's 3 components: $ dd if=bootloader.bin of=spl.bin bs=1 skip=0 count=45056 $ dd if=bootloader.bin of=pbl.uimage bs=1 skip=45056 count=143360 $ dd if=bootloader.bin of=ubnt.uimage bs=1 skip=188416 3. Strip the uImage header from the PBL $ dd if=pbl.uimage of=pbl.lzma bs=64 skip=1 4. Decompress the PBL $ lzma -d pbl.lzma --single-stream The decompressed PBL sha256sum should be d8b406c65240d260cf15be5f97f40c1d6d1b6e61ec3abed37bb841c90fcc1235 5. Open the decompressed PBL using your favorite hexeditor. Locate the control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the label for the signature node is located. Rename the "signature" string at this offset to "signaturr". The patched PBL sha256sum should be d028e374cdb40ba44b6e3cef2e4e8a8c16a3b85eb15d9544d24fdd10eed64c97 6. Compress the patched PBL $ lzma -z pbl --lzma1=dict=67108864 The resulting pbl.lzma file should have the sha256sum 7ae6118928fa0d0b3fe4ff81abd80ecfd9ba2944cb0f0a462b6ae65913088b42 7. Create the PBL uimage $ SOURCE_DATE_EPOCH=1607909492 mkimage -A mips -O u-boot -C lzma -n "U-Boot 2018.03 [UniFi,v1.1.40.71]" -a 84000000 -e 84000000 -T firmware -d pbl.lzma patched_pbl.uimage The resulting patched_pbl.uimage should have the sha256sum b90d7fa2dcc6814180d3943530d8d6b0d6a03636113c94e99af34f196d3cf2ce 8. Reassemble the complete bootloader $ dd if=patched_pbl.uimage of=aligned_pbl.uimage bs=143360 count=1 conv=sync $ cat spl.bin > patched_uboot.bin $ cat aligned_pbl.uimage >> patched_uboot.bin $ cat ubnt.uimage >> patched_uboot.bin The resulting patched_uboot.bin should have the sha256sum 3e1186f33b88a525687285c2a8b22e8786787b31d4648b8eee66c672222aa76b 9. Transfer your patched bootloader to the device. Also install the kmod-mtd-rw package using opkg and load it. $ insmod mtd-rw.ko i_want_a_brick=1 Write the patched bootloader to mtd0 $ mtd write patched_uboot.bin u-boot 10. Erase the kernel1 partition, as the bootloader might otherwise decide to boot from there. $ mtd erase kernel1 11. Transfer the OpenWrt sysupgrade image to the device and install using sysupgrade. FIT configurations ------------------ In the future, the MT7621 UniFi6 family can be supported by a single OpenWrt image. config@1: U6 Lite config@2: U6 IW config@3: U6 Mesh config@4: U6 Extender config@5: U6 LR-EA (Early Access - GA is MT7622) Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for D-Link DIR-882 R1Andrew Pikler2020-12-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7615N (x2) - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 2.0, 1 USB 3.0 - Buttons: Reset, WiFi Toggle, WPS - LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0 The R1 revision is identical to the A1 revision except - No Config2 Parition, therefore - factory partition resized to 64k from 128K - Firmware partition offset is 0x50000 not 0x60000 - Firmware partitions size increased by 64K - Firmware partition type is "denx,uimage", not "sge,uimage" - Padding of image creation "uimage-padhdr 96" removed Installation: - Older firmware versions: put the factory image on a USB stick, turn on the telnet console, and flash using the following cmd "fw_updater Linux /mnt/usb_X_X/firmware.bin" - D-Link FailsafeUI: Power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing, then jack into any lan port and manually assign a static IP address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2) and go to http://192.168.0.1 Flash with the factory image. Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-221-3/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* treewide: fix initramfs detectionRobert Marko2020-12-201-1/+1
| | | | | | | | | | | | | | | | Commit "initramfs: switch to tmpfs to fix ujail" switched initramfs to now use tmpfs, it causes $(rootfs_type) to now return tmpfs when running initramfs image instead of being empty. This broke initramfs detection which is required so that when installing on MikroTik devices firmware partition would first get erased fully before writing. So, lets test for $(rootfs_type) returning "tmpfs" instead. Fixes: 7fd3c68 ("initramfs: switch to tmpfs to fix ujail) Signed-off-by: Robert Marko <robimarko@gmail.com>
* ramips: add support for GL.iNet GL-MT1300Xinfa Deng2020-12-172-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL-MT1300 is a high-performance new generation pocket-sized router that offers a powerful hardware and first-class cybersecurity protocol with unique and modern design. Specifications: - SoC: MT7621A, Dual-Core @880MHz - RAM: 256 MB DDR3 - Flash: 32 MB - Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN - Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps) - USB: 1 x USB 3.0 port - Slot: 1 x MicroSD card slot - Button: 1 x Reset button - Switch: 1 x Mode switch - LED: 1 x Blue LED + 1 x White LED MAC addresses based on vendor firmware: WAN : factory 0x4000 LAN : Mac from factory 0x4000 + 1 2.4GHz : factory 0x4 5GHz : Mac form factory 0x4 + 1 Flashing instructions: 1.Connect to one of LAN ports. 2.Set the static IP on the PC to 192.168.1.2. 3.Press the Reset button and power the device (do not release the button). After waiting for the blue led to flash 5 times, the white led will come on and release the button. 4.Browse the 192.168.1.1 web page and update firmware according to web tips. 5.The blue led will flash when the firmware is being upgraded. 6.The blue led stops blinking to indicate that the firmware upgrade is complete and U-Boot automatically starts the firmware. For more information on GL-MT1300, see the OFFICIAL GL.iNet website: https://www.gl-inet.com/products/gl-mt1300/ Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com> [add input-type for switch, wrap long line in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use full names for Xiaomi Mi Router devicesAdrian Schmutzler2020-12-082-5/+5
| | | | | | | | | | This aligns the device/image names of the older Xiaomi Mi Router devices with their "friendly" model and DEVICE_MODEL properties. This also reintroduces consistency with the newer devices already following that scheme. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ASUS RT-N56U B1Pavel Chervontsev2020-11-281-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621ST (880 MHz) FLASH: 16 MiB (Macronix MX25L12835FM2I-10G) RAM: 128 MiB (Nanya NT5CB64M16FP-DH) WiFi: MediaTek MT7603EN bgn 2x2:2 WiFi: MediaTek MT7612EN an 2x2:2 BTN: Reset, WPS LED: - Power - WiFi 2.4 GHz - WiFi 5 GHz - WAN - LAN {1-4} - USB {1-2} UART: UART is present as pin hole next to the aluminium capacitor. 3V3 - RX - GND - TX / 115200-8N1 3V3 is the nearest on the aluminium capacitor and nut hole (pin1). USB: 2 ports POWER: 12VDC, 1.5A (Barrel 5.5x2.1) Installation: Via TFTP: Set your computers IP-Address to 192.168.1.75 Power up the Router with the Reset button pressed. Release the Reset button after 5 seconds. Upload OpenWRT sysupgrade image via TFTP: tftp -4 -v -m binary 192.168.1.1 -c put IMAGE MAC addresses: 0x4 *:98 2g/wan, label 0x22 *:9c 0x28 *:98 0x8004 *:9c 5g/lan Though addresses are written to 0x22 and 0x28, it appears that the vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the same here. Signed-off-by: Pavel Chervontsev <cherpash@gmail.com> [add MAC address overview, add label-mac-device, fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: fix Telco X1 GPIO switchesDENG Qingfang2020-11-161-1/+1
| | | | | | | The GPIO base of MT7621 GPIO 0~31 is 480 on kernel 5.4 Fix the GPIO numbering. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add Xiaomi Mi Router 4A Gigabit explicitlyAdrian Schmutzler2020-11-121-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-2640 A1James McGuire2020-11-112-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-2640 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue), WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:a7 (label) wan factory 0xe006 *:aa 2.4 factory 0xe000 +1 *:a8 5.0 factory 0xe000 +2 *:a9 Seems like vendor didn't replace the dummy entries in the calibration data. Signed-off-by: James McGuire <jamesm51@gmail.com> [fix device definition title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mt7621: mikrotik: use vmlinuz (zBoot ELF)John Thomson2020-10-291-0/+3
| | | | | | | | | | | | - minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz - ~5 seconds for kernel decompression, which was equivalent to the additional time to load the uncompressed ELF from SPI NOR. - Removes requirement for lzma-loader, which may have been causing some image builds to fail to boot on Mikrotik mt7621. Fixes: FS#3354 Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* ramips: remove set_wifi_led function in 01_ledsAdrian Schmutzler2020-10-021-4/+0
| | | | | | | | | | | | | | | | | | | While we mostly use the ucidef_set_led_* functions directly in 01_leds we still have the set_wifi_led function in parallel for several old devices. This is not only inconsistent with the other definitions, it also links to the wlan0 interface instead of using a phy trigger which would be independent of the interface name (and is used for all newer devices anyway). Apart from that, the standard names "wifi" and "wifi-led" are not very helpful in a world with different radio bands either. Thus, this patch removes the set_wifi_led function and puts the relevant commands into the cases explicitly. This makes the mechanism used more evident and will hopefully lead to some future improvements or at least prevent some copy-pasting of the old setups. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove option to set WiFi LED via aliasesAdrian Schmutzler2020-10-021-3/+0
| | | | | | | | | | | | | In ramips, it's not common to use an alias for specifying the WiFi LED; actually only one device uses this mechanism (TL-WR841N v14). Particularly since the WiFi LEDs are typically distinguished between 2.4G and 5G etc. it is also not very useful for this target. Thus, this patch removes the setup lines for this mechanism and converts the TL-WR841N v14 to the normal setup. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove model name from LED labelsAdrian Schmutzler2020-10-022-68/+37
| | | | | | | | | | | | | | | | | Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v2J. Scott Heppler2020-09-235-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Santiago Rodriguez-Papa <contact at rodsan.dev> Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Winbond W632GG6MB-12 (256M DDR3-1600) * Flash: Winbond W29N01HVSINA (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
* treewide: revert sysupgrade adjustments for early DSA-adoptersAdrian Schmutzler2020-09-081-8/+0
| | | | | | | | | | | | | | | | | The uci-default mechanism to update the compat-version was only meant for early DSA-adopters, which should have updated by now. Remove this workaround again in order to prevent the intended experiences for all the other people. This reverts: a9703db72030 ("mvebu: fix sysupgrade experience for early DSA-adopters") 86c89bf5e8f5 ("kirkwood: fix sysupgrade experience for early DSA-adopters") Partially reverted: 1eac573b5304 ("ramips: mt7621: implement compatibility version for DSA migration") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-2660 A1Josh Bendavid2020-09-062-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-2660 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white), WiFi 5G (white), USB 3.0 (white), USB 2.0 (white) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:a7 (label) wan factory 0xe006 *:aa 2.4 factory 0xe000 +1 *:a8 5.0 factory 0xe000 +2 *:a9 Seems like vendor didn't replace the dummy entries in the calibration data. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com> [rebase onto already merged DIR-1960 A1, add MAC addresses to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Wavlink WL-WN531A6Georgi Vlaev2020-08-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Wavlink WL-WN531A6 (Quantum D6). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK * Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG * WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot. * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot. * Ethernet: MT7630, 5x 1000Base-T * LED: Power, WAN, LAN(x4), WiFi, WPS, dual color "WAVLINK" LED logo on the top cover. * Buttons: Reset, WPS, "Turbo", touch button on the top cover via RH6015C touch sensor. * UART: UART1: serial console (57600 8n1) on the J4 header located below the top heatsink. UART2: J12 header, located on the right side of the board. * USB: One USB3 port. * I2C: J9 header, located below the top heatsink. Backup the OEM Firmware: ----------------------- There isn't any firmware released for the WL-WN531A6 on the Wavlink web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware is stored on /dev/mtd4 ("Kernel"). 1) Plug a FAT32 formatted USB flash drive into the USB port. 2) Navigate to "Setup->USB Storage". Under the "Available Network folder" you can see part of the mount point of the newly mounted flash drive filesystem - e.g "sda1". The full mount point is prefixed with "/media", so in this case the mount point becomes "/media/sda1". 3) Go to http://192.168.10.1/webcmd.shtml . 4) Type the following line in the "Command" input box: dd if=/dev/mtd4ro of=/media/sda1/firmware.bin 5) Click "Apply" 6) After few seconds, in the text area should appear this output: 30080+0 records in 30080+0 records out 7) Type "sync" in the "Command" input box and click "Apply". 8) At this point the OEM firmware is stored on the flash drive as "firmware.bin". The size of the file is 15040 KB. Installation: ------------ * Flashing instructions (OEM web interface): The OEM web interface accepts only files with names containing "WN531A6". It's also impossible to flash the *-sysupgrade.bin image, so we have to flash the *-initramfs-kernel.bin first and use the OpenWrt's upgrade interface to write the sysupgrade image. 1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin to WN531A6.bin. 2) Connect your computer to the one of the LAN ports of the router with an Ethernet cable and open http://192.168.10.1 3) Browse to Setup -> Firmware Upgrade interface. 4) Upload the (renamed) OpenWrt image - WN531A6.bin. 5) Proceed with the firmware installation and give the device a few minutes to finish and reboot. 6) After reboot wait for the "WAVLINK" logo on the top cover to turn solid blue, and open http://192.168.1.1 7) Use the OpenWrt's "Flash Firmware" interface to write the OpenWrt sysupgrade image: openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin * Flashing instructions (u-boot TFTP): 1) Configure a TFTP server on your computer and set its IP to 192.168.10.100 2) Rename the OpenWrt sysupgrade image to firmware.bin and place it in the root folder of the TFTP server. 3) Power off the device and connect an Ethernet cable from one of its LAN ports your computer. 4) Press the "Reset" button (and keep it pressed) 5) Power on the device. 6) After a few seconds, when the connected port LAN LED stops blinking fast, release the "Reset" button. 7) Flashing OpenWrt takes less than a minute, system will reboot automatically. 8) After reboot the WAVLINK logo on the top cover will indicate the current OpenWrt running status (wait until the logo tunrs solid blue). Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow "Flashing instructions (u-boot TFTP)" and use the "firmware.bin" backup image. * OpenWrt "Flash Firmware" interface: Upload the "firmware.bin" backup image and select "Force update" before continuing. Notes: ----- * The MAC address shown on the label at the back of the device is assigned to the 2.4G WiFi adapter. MAC addresses assigned by the OEM firmware: 2.4G: *:XX (label): factory@0x0004 5G: *:XX + 1 : factory@0x8004 WAN: *:XX - 1 : factory@0xe006 LAN: *:XX - 2 : factory@0xe000 * The I2C bus and UART2 are fully functional. The headers are not populated. Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix LED labels for Asus RT-AC65PAdrian Schmutzler2020-08-171-0/+3
| | | | | | | | | | | | | The leds block was copied over from the RT-AC85P DTS to the common DTSI while keeping the device-specific model name in the label. This moves the LEDs back to the DTS files and adjusts the names to properly resemble the model name of the devices used at, just like it is handled on most other devices. Fixes: 7c5f712e4fec ("ramips: add support for Asus RT-AC65P") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)John Thomson2020-08-134-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 760iGS router. It is similar to the already supported RouterBOARD 750Gr3. The 760iGS device features an added SFP cage, and passive PoE out on port 5 compared to the RB750Gr3. https://mikrotik.com/product/hex_s Specifications: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB - RAM: 256 MB - Ethernet: 5x 10/100/1000 Mbps - SFP cage - USB port - microSD slot Unsupported: - Beeper (requires PWM driver) - ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1) The linux driver requires an interrupt, and pendown GPIO These are unknown, and not needed with the touchscreen only used for temperature and voltage monitoring. ads7846 hwmon: temp0 is degrees Celsius temp1 is voltage * 32 GPIOs: - 07: input passive PoE out (lan5) compatible (Mikrotik) device connected - 17: output passive PoE out (lan5) switch Installation through RouterBoot follows the usual MikroTik method https://openwrt.org/toh/mikrotik/common To boot to intramfs image in RAM: 1. Setup TFTP server to serve intramfs image. 2. Plug Ethernet cable into WAN port. 3. Unplug power, hold reset button and plug power in. Wait (~25 seconds) for beep and then release reset button. The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT. 4. Wait for a minute. Router should be running OpenWrt, check by plugging in to port 2-5 and going to 192.168.1.1. To install OpenWrt to flash: 1. Follow steps above to boot intramfs image in RAM. 2. Flash the sysupgrade.bin image with web interface or sysupgrade. 3. Once the router reboots you will be running OpenWrt from flash. OEM firmware differences: - RouterOS assigns a different MAC address for each port - The first address (E01 on the sticker) is used for wan (ether1 in OEM). - The next address is used for lan2. - The last address (E06 on the sticker) is used for sfp. [Initial port work, shared dtsi] Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com> [SFP support and GPIO identification] Signed-off-by: Luka Logar <luka.logar@iname.com> [Misc. fixes and submission] Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [rebase, drop uart3 from state_default on 750gr3, minor commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: implement compatibility version for DSA migrationAdrian Schmutzler2020-08-082-0/+27
| | | | | | | | | | | | | | | | | | | This implements the newly introduced compat-version to prevent broken upgrade between swconfig and DSA for ramips' mt7621 subtarget. In order to make the situation more transparent for the user, and to prevent large switch-cases for devices, it is more convenient to have the entire subtarget 1.1-by-default. This means that new devices will be added with 1.1 from the start, but in contrast we don't need to switch them in board.d files. Apart from that, users that manually backport devices to 19.07 with swconfig will have an equivalent upgrade experience to officially supported devices. Since DSA support on mt7621 is out for a while already, this applies the same uci-defaults workaround for early adopters as already done for kirkwood and mvebu in previous commits. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: invert wpad selection for mt7621Adrian Schmutzler2020-08-071-0/+2
| | | | | | | | | | | | | | | | | | | For ramips/mt7621, the wpad-basic package is not selected by default, but added for every device individually as needed. While this might be technically correct if the SoC does not come with a Wifi module, only 18 of 97 devices for that platform are set up _without_ wpad-basic currently. Therefore, it seems more convenient to add wpad-basic by default for the subtarget and then just remove it for the 18 mentioned devices, instead of having to add it for about 60 times instead. This would also match the behavior of the 5 other subtargets, where wpad-basic/wpad-mini is added by default as well, and thus be more obvious to developers without detailed SoC knowledge. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: switch rt305x subtarget to kernel 5.4Alexey Dobrovolsky2020-08-051-2/+0
| | | | | | | | | | | | | | RT3x5x seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Since 4 of 6 targets are on kernel 5.4 now, invert the kernel version setup logic in Makefile/target.mk files. Tested on ZyXEL Keenetic. Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [invert version setup logic] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: replace remaining occurrences of ifconfig with ipAdrian Schmutzler2020-08-031-1/+1
| | | | | | | | | | | ifconfig is effectively deprecated for quite some time now. Let's replace the remaining occurrences for our target setup by the corresponding ip commands now. Note that this does not touch ar71xx, as it will be dropped anyway, and changing it would only make backports harder. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-1960 A1Josh Bendavid2020-07-272-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-1960 A1. Given the similarity with the DIR-1760/2660 A1, this patch also introduces a common DTSI which can be shared with these devices, with support to be added in future commits. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 256 MB (DDR3) * Flash: 128 MB (NAND) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 3.0 * Buttons: Reset, WPS * LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white), WiFi 5G (white), USB 3.0 (white) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 MAC addresses: lan factory 0xe000 *:EB (label) wan factory 0xe006 *:EE 2.4 factory 0xe000 +1 *:EC 5.0 factory 0xe000 +2 *:ED Seems like vendor didn't replace the dummy entrys in the calibration data. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com> [fix whitespace issues, create patch to merge DIR-1960 first, move special WiFi MAC settings to DTS, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove non-existant poe_passthrough for RouterBOARD 750Gr3John Thomson2020-07-251-3/+0
| | | | | | | | | | | | | | | | This 750gr3 GPIO17 switch was added based on vendor source, but only the 760iGS (which shares the rbsysfs board identifier) device has the physical wiring. The 750Gr3 actually does not support PoE out. Apart from that, note that the gpio base (480) would have required this GPIO to be referenced as 497 if it was kept. Fixes: 6ba58b7b020c ("ramips: cleanup the RB750Gr3 support") Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Winstars WS-WN583A6Davide Fioravanti2020-07-251-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet ports. Even if mine is branded as "Gemeita AC2100", the sticker on the back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6. Probably the real product name is the Wavlink WL-WN583A6 because of the many references to Wavlink in the OEM firmware and bootlog. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 8MB NOR (GigaDevice GD25Q64B) ETH: 2x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7603E (2x2:2) - 5GHz: 1x MT7615E (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x WPS button - 1x ON/OFF switch (working but unmodifiable) - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3) LEDS: - 1x White led - 1x Red led - 1x Amber led - 1x Blue led - 2x Blue leds (lan and wan port status: working but unmodifiable) UART: - 57600-8-N-1 Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M83A6.V5030.191210 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box: mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done 3) Click "Apply" 4) After few seconds, in the textarea should appear this output: 16384+0 records in 16384+0 records out 8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s 384+0 records in 384+0 records out 196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s 15744+0 records in 15744+0 records out 8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s dd: can't open '/dev/mtd5ro': No such device dd: can't open '/dev/mtd6ro': No such device dd: can't open '/dev/mtd7ro': No such device Excluding the "X.XXXXXX seconds" part, you should get the same exact output. If your output doesn't match mine, stop reading and ask for help in the forum. 5) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd0ro http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files weight 0 byte, stop reading and ask for help in the forum. 6) Store these downloaded files in a safe place. 7) Reboot your router to remove any temporary file from your router. Installation ------------ Flash the initramfs image in the OEM firmware interface. When openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) The "System Command" page allows to run every command as root. For example you can use "dd" and "nc" to backup the OEM firmware. PC (SERVER): nc -l 5555 > ./mtdXro ROUTER (CLIENT): dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555 2) The OEM web interface accepts only images containing the string "WN583A6" in the filename. Currently the OEM interface accepts only the initramfs image probably because it checks if the ih_size in the image header is equal to the whole image size (instead of the kernel size) Read more here: https://forum.openwrt.org/t/support-for-strong-1200/22768/19 3) The white led (namely "Smart Night Light") can be controller by the user only if the side switch is set to "Schedule" otherwise it will be activated by the light condition (there is a photodiode on the top side of the router) 4) Router mac addresses: LAN XX:XX:XX:XX:XX:8F WAN XX:XX:XX:XX:XX:90 WIFI 2G XX:XX:XX:XX:XX:91 WIFI 5G XX:XX:XX:XX:XX:92 LABEL XX:XX:XX:XX:XX:91 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [remove chosen node, fix whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix network setup for Ubiquiti ER-X/ER-X-SFPNelson Cai2020-07-201-2/+2
| | | | | | | | | | | | The function name ucidef_set_interface_lan_wan does not exist, use the proper name by adding an "s" and thereby fix network setup on these devices. Fixes: 22468cc40c8b (ramips: erx and erx-sfp: fix missing WAN interface) Signed-off-by: Nelson Cai <niphor@gmail.com> [commit message/title facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for D-Link DIR-867/DIR-882 A1Mateus B. Cassiano2020-07-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 09:57:04 +0000