aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7620/base-files/etc
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix lan leds for Wavlink WL-WN535K1Davide Fioravanti2023-06-252-3/+3
| | | | | | | | | | Previously both lan1 and lan2 leds were wrongly labelled as lan2. Moreover they were connected to the wrong lan port. Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1") Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit c71dada92654a53c63bbc5bebcc40fe924750ed7)
* ramips: add support for Keenetic Lite III rev. AAlexey Bartenev2023-03-272-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General specification: SoC Type: MediaTek MT7620N (580MHz) ROM: 8 MB SPI-NOR (W25Q64FV) RAM: 64 MB DDR (EM6AB160TSD-5G) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Buttons: 3 button (POWER, RESET, WPS) Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT) Bootloader: U-Boot 1.1.3 Power: 9 VDC, 0.6 A MAC in stock: |- + | | LAN | RF-EEPROM + 0x04 | | WLAN | RF-EEPROM + 0x04 | | WAN | RF-EEPROM + 0x28 | OEM easy installation 1. Use a PC to browse to http://my.keenetic.net. 2. Go to the System section and open the Files tab. 3. Under the Files tab, there will be a list of system files. Click on the Firmware file. 4. When a modal window appears, click on the Choose File button and upload the firmware image. 5. Wait for the router to flash and reboot. OEM installation using the TFTP method 1. Download the latest firmware image and rename it to klite3_recovery.bin. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.1.2 and subnet mask 255.255.255.0. 5. Power up the router while holding the reset button pressed. 6. Wait approximately for 5 seconds and then release the reset button. 7. The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me>
* ramips: add label MAC address for EPG600 and ESR600Michael Pratt2023-02-181-0/+1
| | | | | | | set label mac for the current ESR600 and new EPG600 using the board.d scripts Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for Senao Engenius EPG600Michael Pratt2023-02-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EPG600 Engenius EPG600 is an indoor wireless router with 1 Gb ethernet switch, dual-band wireless, internal antenna plates, USB, and phone lines (not supported) this board is a Senao device: the hardware is equivalent to EnGenius ESR600 (except for phone lines) the software is Senao SDK which is based on openwrt and uboot which uses the legacy Senao header with Vendor / Product IDs to verify the firmware upgrade image. **Specification:** - MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2 - RT5592N WLAN PCI chip, 5 GHz, 2x2 - QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 64 MB RAM NT5TU32M16 - UART console J2, populated - USB 2.0 port direct to SOC - 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line - 3 buttons reset, wps, "reg" (registeration) - 4 antennas internal omni-directional plates NOT YET SUPPORTED: VoIP - Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data - Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins) **MAC addresses:** MAC address labeled as MAC ADDRESS MACs present in both wifi cal data and uboot environment eth0.1/phy1 ---- *:82 rf 0x4 phy0 ---- *:83 factory 0x4 eth0.2 MAC *:b8 "wanaddr" **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.0.1 username and password 'admin' Navigate to gear icon, "Device Management", "Tools" select the factory.dlf image Upload and verify checksum Method 2: Serial to upload initramfs: Follow directions for TFTP recovery upload and boot initramfs and do a sysupgrade **TFTP recovery:** Requires UART serial console, reset button does nothing rename initramfs-kernel.bin to 'uImageEPG600' make available on TFTP server at 192.168.99.8 power board, interrupt boot with "4" execute `tftpboot` and `bootm` (with the load address) **Return to OEM:** Images from OEM are provided, but not compatible with openwrt sysupgrade. So it must be modified. Alternatively, back up all mtd partitions before flashing **Note on switch registers:** The necessary registers needed for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by using the following lines in the switch driver ar8327.c in the function 'ar8327_hw_config_of' where 'qca,ar8327-initvals' is parsed from DTS before the new register values are written: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE)); pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE)); pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP)); Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for SNR-CPE-W4N-MT routerAlexey Bartenev2022-12-172-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General specification: - SoC Type: MediaTek MT7620N (580MHz) - ROM: 8 MB SPI-NOR (W25Q64FV) - RAM: 64 MB DDR (M13S5121632A) - Switch: MediaTek MT7530 - Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) - Wireless 2.4 GHz: b/g/n - Buttons: 1 button (RESET) - Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5 - Power: 12 VDC, 1.0 A Flash by the native uploader in 2 stages: 1. Use the native uploader to flash an initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by "Administration/Management/Firmware update/Choose File" in vendor's web interface (ip: 192.168.1.10, login: Admin, password: Admin). Wait ~160 seconds. 2. Flash a sysupgrade image via the initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin file by "System/Backup/Flash Firmware/Flash image..." in LuCI web interface (ip: 192.168.1.1, login: root, no password). Wait ~240 seconds. Flash by U-Boot TFTP method: 1. Configure your PC with IP 192.168.1.131 2. Set up TFTP server and put the openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin image on your PC 3. Connect serial port (57600 8N1) and turn on the router. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.131) ==:192.168.1.131 Input Linux Kernel filename () ==: openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Bartenev <41exey@proton.me>
* ramips: add support for Amped Wireless B1200EXDaniel Fuchs2022-11-132-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is almost identical to the already supported Edimax EW-7476RP5, the only differences are: - There is no mode selection slider switch on this device - The two wireless LEDs are green instead of blue - Model name in the CSYS header is RN10 Additional changes: - Moved WiFi LEDs and the slider switch to the individual dt files - Added ieee80211-freq-limit to the mt7612e radio to properly disable 2.4GHz band on this radio Device specifications: SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS/RESET LED: - WiFi 5G (green) - WiFi 2.4G (green) - Signal Strength (green) - Power (green) - WPS (green) - LAN (green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the WPS button 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: Upload the sysupgrade image via the default web interface Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
* ramips: add support for Youku X2Shiji Yang2022-11-051-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: MT7620AN + MT7612EN RAM: 128 MiB DDR2 Flash: 16 MiB (Winbond W25Q28FVFG) WLAN: 2.4G + 5G LAN: LAN ports *2 WAN: WAN port *1 USB: USB2.0 *1 SD Card: MicroSD *1 Buttons: Reset *1 LEDs: ethernet *3, system, usb, wlan2g, wlan5g MAC Address: use address source label 54:36:9b:xx:xx:ac lan lan 54:36:9b:xx:xx:ac factory.0x0028 wan 54:36:9b:xx:xx:ad factory.0x002e wlan2g 54:36:9b:xx:xx:ae factory.0x0004 wlan5g 54:36:9b:xx:xx:af factory.0x8004 Installation: 1. Apply initramfs-kernel.bin in stock firmware Web UI. 2. Install sysupgrade.bin on OpenWrt and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Netcore NW5212David Yang2022-08-062-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netcore NW5212, provided by some carrier in China. Specifications: -------------- * SoC: Mediatek MT7620A * RAM: 128MB DDR2 * Flash: 16MB SPI NOR flash (Winbond W25Q128BV) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, WAN, LAN 1-4, WiFi * Buttons: Reset (GPIO 13) * UART: Serial console (57600 8n1) * USB: 1 x USB2 Installation: ------------ The router comes with OpenWrt 14.07 built with MTK SDK. However, as the modem is provided by carriers, so the web interface is highly minimized and only contains a static page with no interaction options. There are two possible ways to gain the access. 1) Open the shell and use a UART2USB convert to gain TTY access. Please notice you have to remove resistance R54 at the back of the board otherwise you won't be able to input anything. 2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to start dropbear service at port 9122. Be warned the software is super old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1, kexguess2@matt.ucc.asn.au is support, you may not be able to connect it with an up-to-date ssh client. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via original firmware): 1) Setup HTTP server on your computer, for example: python3 -m http.server 2) Connect to the route and flash: cd /tmp wget http://<your-computer-host>/<your-firmware-name> mtd -r write <your-firmware-name> firmware Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset13.bin mtd write breed-mt7620-reset13.bin Bootloader 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose the flash layout to be 0x50000 and flash new firmware. MAC addresses: ------------- There are three MACs stored in factory, as in MT7620A reference design: source address usage 0x4 label WLAN 0x28 label MAC 1 0x2e label + 1 MAC 2 However, the OEM firmware only uses one single MAC (label) for all interfaces, probably a misconfiguration. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: add support for Netgear PR2000David Yang2022-08-062-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear PR2000, sold as "Travel Router and Range Extender". Specifications: -------------- * SoC: Mediatek MT7620N * RAM: 64MB DDR2 * Flash: 16MB SPI NOR flash (Macronix MX25L12805D) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, Internet, WiFi, USB * Buttons: Reset (GPIO 1/2) * UART: Serial console (57600 8n1) * USB: 1 x USB2 SPECIAL NOTES: ------------- Problem: WiFi is super weak, but SSID beacons seems to be right. Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0. Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2 of 36h indicates the presence of External LNA for 11g (2.4 GHz) band, which seems to be incorrectly set by Netgear (originally 0x04). Lifting it solves the problem of weak RX signal. Installation: ------------ There are two possible ways to install the firmware. Flashing via web interface of original firmware is not tested due to a broken firmware. 1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD, TP9: TXD, TP10: GND). Please notice you have to remove resistance R54 next to TP7 otherwise you won't be able to input anything. 2) Use well-known Netgear debug switch. Access http://192.168.168.1/setup.cgi?todo=debug to start telnet service (username: root, password: <none>). Please back up firmware if you want to go back to the original. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via nmrpflash): 1) Download nmrpflash from https://github.com/jclehner/nmrpflash 2) Use *-factory.img and flash: nmrpflash -L nmrpflash -i net* -f <your-firmware-name> 3) Turn off then turn on the device, wait it finishing flash. Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset1.bin dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose memory layout to be 0x40000 and flash new firmware. Remark: ------ As a "Range Extender", it has a switch to switch between Wired mode (GPIO 21 low) and Wireless mode (GPIO 20 low), which is not implemented in this patch. However, the router will be turned off when it switches to the middle, which makes this switch much less useful. MAC addresses: ------------- The OEM firmware uses one single MAC for all interfaces, located at 0xf700b0. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: fix wifi mac address of HiWiFi series devicesShiji Yang2022-03-261-0/+26
| | | | | | | | | | | | | | | | | | For HiWiFi series devices, label_mac can be read from bdinfo partition, and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's label_mac start with D4:EE) For example: label D4:EE:07:32:84:88 lan D4:EE:07:32:84:88 wan D4:EE:07:32:84:89 wlan2g D4:EE:07:32:84:88 wlan5g D0:EE:07:32:84:88 Tested on HiWiFi HC5661. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Netgear WN3100RPv2Rodolphe de Saint Léger2022-03-162-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* Revert "ramips: add support for Netgear WN3000RPv3"Sungbo Eo2022-03-162-3/+1
| | | | | | | | | This reverts commit 7bc20cb6143e089fae6ad4b173fc42b55bdbecfe. It adds support for Netgear WN3100RPv2, but the commit title is wrong. It will be re-added with the correct title. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Netgear WN3000RPv3Rodolphe de Saint Léger2022-03-162-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: Add support for D-Link DWR-961 A1Pawel Dembicki2022-03-164-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-961 A1 Wireless Router is based on the MT7620A SoC. It's a merge of two Amit boards: DWR-960 with ethernet part of Lava LR-25G001. ROMID it's taken from Telenor branded version and it works with tested device. Images from D-Link site for this router are from DWR-953 and it have ROMID DLK6E2424001. I don't know if it's mistake on web-site or if it's will require different image. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612 mpcie card) - 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem cat 6 - UART (J5) header on PCB (57600 8n1) - 13x LED, 2x button - JBOOT bootloader Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for Wavlink WL-WN535K1Davide Fioravanti2022-01-302-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports and one fast ethernet port. Mine is branded as Talius TAL-WMESH1. It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3). The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could potentially work for WL-WN535G3R and WS-WN535G3R with little to none effort, but it's untested. Hardware -------- SoC: Mediatek MT7620A RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CS) ETH: - 2x 10/100/1000 Mbps Ethernet (RTL8211F) - 1x 10/100 Mbps Ethernet (integrated in SOC) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 internal antennas BTN: - 1x Reset button - 1x Touchlink button (set to WPS) - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 3x Green leds (ethernet port status/act) UART: - 57600-8-N-1 Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on WN535K1_V1510_200916 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: 16384+0 records in 16384+0 records out If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done 6) After few seconds, in the textarea should appear this output: 384+0 records in 384+0 records out 128+0 records in 128+0 records out 128+0 records in 128+0 records out 14720+0 records in 14720+0 records out 1024+0 records in 1024+0 records out If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro http://192.168.10.1/dev/mtd5ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update_mesh.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:E2 (factory @ 0x28) WAN XX:XX:XX:XX:XX:E3 (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:E4 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:E5 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:E5 2) The OEM firmware upgrade page accepts only files containing the string "WN535K1" in the filename. 3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid (https://github.com/openwrt/openwrt/commit/92780d80ab6f5f03fac2407c06eb267dd83914a1) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [remove trailing whitespace] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for HUMAX E2Kyoungkyu Park2022-01-152-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB (MXIC MX25L6405D) - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610E - Ethernet: 1x 10/100Mbps - Switch: SoC internal - UART: J2 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation and Recovery via TFTP: 1. Connect ethernet cable between Router port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) 5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!** The device will be automatically rebooted. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
* ramips: add support for WeVO AIR DUOSungbo Eo2021-12-291-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on MediaTek MT7620A. Specifications: * SoC: MT7620A * RAM: 64 MiB * Flash: SPI NOR 16 MiB * USB & SATA bridge controller: JMicron JMS567 * SATA 6Gb/s: 2.5" drive slot * USB 3.0: Micro-B * USB 2.0: connected to SoC * Wi-Fi: * 2.4 GHz: SoC built-in * 5 GHz: MT7612EN * Ethernet: 5x 1GbE * Switch: MT7530WU * UART: 4-pin 1.27 mm pitch through-hole (57600 baud) * Pinout: (3V3)|(RXD) (TXD) (GND) Notes: * The drive is accessible through the external USB port only when the router is turned off. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. The image filename should have ".upload" extension. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: tidy up 02_networkSungbo Eo2021-12-161-14/+8
| | | | | | | * fix alphabetic sorting * consolidate duplicate cases Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: Enable PHY aneg of Lava LR-25G001Pawel Dembicki2021-12-041-7/+1
| | | | | | | | | | | | | | | | | | | | | | | | | In 20b09a2125f5 Lava LR-25G001 router have problem with two inactive ethernet ports. JBOOT bootloader didn't configure ethernet devices by default. The same situation was there. It is required to enable all phy ports. This is fragment of stock bootlog: switch reg write_athr offset=90, value=2b0 switch reg write_athr offset=8c, value=2b0 switch reg write_athr offset=88, value=2b0 switch reg write_athr offset=84, value=2b0 switch reg write_athr offset=80, value=2b0 This patch adds proper registers configuration ar8337 initvals. 0x2b0 value causes force flow control configuration, 0x1200 was used instead (flow control config auto-neg with phy). [1] When switch is now ok, let's fix port numeration too. Fixes: 20b09a2125f5 ("ramips: add support for Lava LR-25G001") [1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix LAVA LR-25G001 broken wifi led triggersJani Partanen2021-10-301-4/+0
| | | | | | | | | | | | | | | LED labels for this device are different in 01_leds file and in device DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone device. This has not been tested on the LR-25G001 itself, just on the clone mentioned above. Fixes: 20b09a2125f5 ("ramips: add support for Lava LR-25G001") Signed-off-by: Jani Partanen <rtfm@iki.fi> [rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Sitecom WLR-4100 v1 002Andrea Poletti2021-09-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router Specification: SoC: MT7620A RAM: 64 MB DDR2 Flash: MX25L6405D SPI NOR 8 MB WIFI: 2.4 GHz integrated Ethernet: 5x 10/100/1000 Mbps QCA8337 USB: 1x 2.0 LEDS: 2x GPIO controlled, 5x switch Buttons: 1x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB: VCC 3.3V GND TX RX baud: 115200, parity: none, flow control: none Installation Connect to one of LAN (yellow) ethernet ports, Open router configuration interface, Go to Toolbox > Firmware, Browse for OpenWrt factory image with dlf extension and hit Apply, Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues Some USB 2.0 devices work at full speed mode 1.1 only MAC addresses factory partition only contains one (binary) MAC address in 0x4. u-boot-env contains four (ascii) MAC addresses, of which two appear to be valid. factory 0x4 **:**:**:**:b9:84 binary u-boot-env ethaddr **:**:**:**:b9:84 ascii u-boot-env wanaddr **:**:**:**:b9:85 ascii u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii The factory firmware only assigns ethaddr. Thus, we take the binary value which we can use directly in DTS. Additional information OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), based on RT3352 SoC Signed-off-by: Andrea Poletti <polex73@yahoo.it> [remove config DT label, convert to nvmem, remove MAC address setup from u-boot-env, add MAC address info to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: expose ephy leds for miwifi-miniDavid Yang2021-08-251-0/+5
| | | | | | | | Give users more control by exposing ephy leds. Signed-off-by: David Yang <mmyangfl@gmail.com> [remove execute bit on 01_leds, add status for gpio2] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for DomyWifi DM202/DM203/DW22DShiji Yang2021-08-252-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SOC: MT7620A + MT7610E * ROM: 16 MiB spi flash (W25Q128FVSG) * RAM: 128 MiB DDR2 (W971GG6KB-25) * WAN: 10/100M *1 * LAN: 10/100M *4 * USB: Type-A USB2.0 *1 * SD: MicroSD *1 * Button: Reset *1 * Antennas: 2.4 GHz *2 + 5 GHz *1 * TTL Baudrate: 57600 * U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3 Installation: * Web UI Update 1. Open http://192.168.10.1/upgrade.html in the browser. 2. Rename firmware to a short name like firmware.bin and then upload it. 3. Fill in the password column with the following content: password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware * TFTP + U-Boot 1. Connect device with a TTL cable. 2. Press "2" when booting to select "Load system code then write to Flash via TFTP". 3. Upload firmware by tftpd64, it will boot when write instruction is executed. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add new flash layout support to Phicomm K2Shiji Yang2021-08-241-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Descriptions： Phicomm K2 (PSG1218) got a new "permanent_config" partition after update firmware to v22.5. This partition located in front of the firmware partition, same as The Phicomm K2P and K2G. Due to this change the new bootloader can't load previous firmware any more. This commit is aimed at add support for Phicomm K2 which official firmware version is 22.5.x or newer. For which runs old firmware version, just update OpenWrt that has a prefix of "k2-v22.4". For uniform naming, this commit also changed the model name PSG1218 to a more recognizable name K2, refer to Phicomm K2G, K2P K2T. OpenWrt selection table: official firmware version OpenWrt v22.4.x.x or older phicomm_k2-v22.4 v22.5.x.x or newer phicomm_k2-v22.5 Installation: Same as Phicomm K2G, K2P, PSG1208. a. TFTP + U-Boot b. Open telnet by some web page vulnerability (Search Baidu by key words "K2 telnet"), and then we can upload firmware image to /tmp and write it to firmware partition with mtd instruction. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [rebase, add/harmonize version in model variables, fix version typo in commit message, wrap commit message properly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: disable SOC VLANs for external switchesMichael Pratt2021-06-231-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | These boards have AR8327 or QCA8337 external ethernet switch. The SOC also has it's own internal switch where VLAN is now enabled by default. Changes to preinit caused all switches to have VLANs enabled by default even if they are not configured with a topology in uci_defaults (see commit f017f617aecbd47debd4d3a734dc0e471342db96) When both internal and external switches have VLANs, and the external switch has both LAN and WAN, the TX traffic from the SOC cannot flow to the tagged port on the external switch because the VLAN IDs are not matching. So disable the internal switch VLANs by default on these boards. Also, add a topology for the internal switch, so that on LuCI there is not an "unknown topology" warning. In theory, it may be possible to have LAN ports on both switches through internal and external PHYs, but there are no known boards that have this. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for the Wavlink WL-WN579X3Ben Gainey2021-06-062-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | About the device ---------------- SoC: MediaTek MT7620a @ 580MHz RAM: 64M FLASH: 8MB WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 2x (RTL8211F) BTN: - WPS - Reset - Router/Repeater/AP (3-way slide-switch) LED: - WPS (blue) - 3-segment Wifi signal representation (blue) - WiFi (blue) - WAN (blue) - LAN (blue) - Power (blue) UART: UART is present as Pads with through-holes on the PCB. They are located next to the reset button and are labelled Vcc/TX/RX/GND as appropriate. Use 3.3V, 57600-8N1. Installation ------------ Using the webcmd interface -------------------------- Warning: Do not update to the latest Wavlink firmware (version 20201201) as this removes the webcmd console and you will need to use the serial port instead. You will need to have built uboot/sqauashfs image for this device, and you will need to provide an HTTP service where the image can be downloaded from that is accessible by the device. You cannot use the device manufacturers firmware upgrade interface as it rejects the OpenWrt image. 1. Log into the device's admin portal. This is necessary to authenticate you as a user in order to be able to access the webcmd interface. 2. Navigate to http://<device-ip>/webcmd.shtml - you can access the console directly through this page, or you may wish to launch the installed `telnetd` and use telnet instead. * Using telnet is recommended since it provides a more convenient shell interface that the web form. * Launch telnetd from the form with the command `telnetd`. * Check the port that telnetd is running on using `netstat -antp|grep telnetd`, it is likely to be 2323. * Connect to the target using `telnet`. The username should be `admin2860`, and the password is your admin password. 3. On the target use `curl` to download the image. e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\ wavlink_wl-wn579x3-squashfs-sysupgrade.bin`. Check the hash using `md5sum`. 4. Use the mtd_write command to flash the image. * The flash partition should be mtd4, but check /sys/class/mtd/mtd4/name first. The partition should be called 'Kernel'. * To flash use the following command: `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>` Where mtd<n> is the Kernel partition, and <image-file> is the OpenWrt image previously downloaded. * The command above will erase, flash and then reboot the device. Once it reboots it will be running OpenWrt. Connect via ssh to the device at 192.168.1.1 on the LAN port. The WAN port will be configured via DHCP. Using the serial port --------------------- The device uses uboot like many other MT7260a based boards. To use this interface, you will need to connect to the serial interface, and provide a TFTP server. At boot follow the bootloader menu and select option 2 to erase/flash the image. Provide the address and filename details for the tftp server. The bootloader will do the rest. Once the image is flashed, the board will boot into OpenWrt. The console is available over the serial port. Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
* ramips: split Youku YK1 to YK-L1 and YK-L1cShiji Yang2021-06-051-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Model: Youku YK-L1/L1c * CPU: MT7620A * RAM: 128 MiB * Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c) * LAN: 2* 10M/100M Ports * WAN: 1* 10M/100M Port * USB: 1* USB2.0 * SD: 1* MicroSD socket * UART: 1* TTL, Baudrate 57600 Descriptions: Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look really different, the only hardware difference between the two models is flash size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can compatible with YK-L1's firmware but it's better to split it to different models. It is easy to identify the models by looking at the label on the bottom of the device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update" to install compatible firmware, so please backup config file before system upgrade. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [use more specific name for DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix mac addresses of Youku YK1Shiji Yang2021-05-101-2/+2
| | | | | | | | | | | | | | MAC addresses read from official firmware value location Wlan xx 71 de factory@0x04 Lan xx 71 dd factory@0x28 Wan xx 71 df factory@0x2e Label xx 71 dd factory@0x28 Signed-off-by: Shiji Yang <yangshiji66@qq.com> [fix sorting in 02_network, redact commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve pinctrl for Youku YK-L1Shiji Yang2021-04-101-4/+0
| | | | | | | 1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it. 2. led "wan" can be triggered by ethernet pinctrl by default so just drop it. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: correct switch config of Youku yk1Shiji Yang2021-03-271-1/+4
| | | | | | | | | | There are only two lan ports and one wan port on Youku yk1 Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-063-3/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix Phicomm PSG1218A switch port labelsShiji Yang2021-02-221-1/+1
| | | | | | | | The lan port sequence was reversed compared to the labels. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [improve commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: correct/add Phicomm K2x WAN/label MAC addressShiji Yang2021-02-221-4/+4
| | | | | | | | | | | | | | Phicomm K2G: add missing label_mac Phicomm PSG1218A & PSG1218B: The previous wan mac was set as factory@0x28 +1 (originally based on the default case for the ramips target), but the correct wan mac is factory@0x28 -1, being equal to factory@0x2e. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Wavlink WL-WN530HG4Nuno Goncalves2020-10-271-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Same hardware as Phicomm K2G but different flash layout. Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: To avoid requiring UART for TFTP a dual flash procedure is suggested to install the squashfs image: 1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin to WN530HG4-WAVLINK. 2. Flash this file with the factory web interface. 3. With OpenWRT now running use standard sysupgrade to install the squashfs image. Signed-off-by: Nuno Goncalves <nunojpg@gmail.com> [remove dts-v1, remove model from LED labels, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove set_wifi_led function in 01_ledsAdrian Schmutzler2020-10-021-30/+26
| | | | | | | | | | | | | | | | | | | While we mostly use the ucidef_set_led_* functions directly in 01_leds we still have the set_wifi_led function in parallel for several old devices. This is not only inconsistent with the other definitions, it also links to the wlan0 interface instead of using a phy trigger which would be independent of the interface name (and is used for all newer devices anyway). Apart from that, the standard names "wifi" and "wifi-led" are not very helpful in a world with different radio bands either. Thus, this patch removes the set_wifi_led function and puts the relevant commands into the cases explicitly. This makes the mechanism used more evident and will hopefully lead to some future improvements or at least prevent some copy-pasting of the old setups. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove option to set WiFi LED via aliasesAdrian Schmutzler2020-10-021-3/+0
| | | | | | | | | | | | | In ramips, it's not common to use an alias for specifying the WiFi LED; actually only one device uses this mechanism (TL-WR841N v14). Particularly since the WiFi LEDs are typically distinguished between 2.4G and 5G etc. it is also not very useful for this target. Thus, this patch removes the setup lines for this mechanism and converts the TL-WR841N v14 to the normal setup. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove model name from LED labelsAdrian Schmutzler2020-10-022-152/+95
| | | | | | | | | | | | | | | | | Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: assign LEDs for RAVPower RP-WD03Adrian Schmutzler2020-09-121-0/+3
| | | | | | | | | | | | | | | According to the User Manual, there is a "Wi-Fi LED" with blue and green colors, doing the following by default: Flashing Blue: System loading Solid Blue: System loaded Flashing Green: Connecting to the Internet Solid Green: Connected to the Internet According to this vendor behavior, we keep refer to the LED as "wifi" but implement the according default behavior as in OEM firmware. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix partitions and boot for RAVPower RP-WD03Adrian Schmutzler2020-09-111-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD03 is a battery powered router, with an Ethernet and USB port. Due due a limitation in the vendor supplied U-Boot bootloader, we cannot exceed a 1.5 MB kernel size, as is the case with recent builds (i.e. post v19.07). This breaks both factory and sysupgrade images. To address this, use the lzma loader (loader-okli) to work around this limitation. The improvements here also address the "misplaced" U-Boot environment partition, which is located between the kernel and rootfs in the stock image / implementation. This is addressed by making use of mtd-concat, maximizing space available in the booted image. This will make sysupgrade from earlier versions impossible. Changes are based on the recently supported HooToo HT-TM05, as the hardware is almost identical (except for RAM size) and is from the same vendor (SunValley). While at it, also change the SPI frequency accordingly. Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions Most of the changes in this commit are the work of Russell Morris (as credited below), I only wrapped them up and added compat-version. Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader to work! Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use proper name for RAVPower RP-WD03Adrian Schmutzler2020-09-112-1/+4
| | | | | | | | The proper model name is RP-WD03 (i.e. with the RP- prefix). Adjust all names to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for HooToo HT-TM05Russell Morris2020-09-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port. Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli). Specifications: SOC: MediaTek MT7620N BATTERY: 10400mAh WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: 64 MB FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz Flash itself specified to 80 MHz, but speed limited by mt7620 SPI fast-read enabled (m25p) LED: Status LED (blue after boot, green with WiFi traffic 4 leds to indicate power level of the battery (unable to control) INPUT: Power, reset button MAC assignment based on vendor firmware: 2.4 GHz *:b4 (factory 0x04) LAN/label *:b4 (factory 0x28) WAN *:b5 (factory 0x2e) Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - Installation from TFTP (recovery) - OpenWRT sysupgrade (Preserving and non-preserving), through the usual ways: command line and LuCI - LEDs (except as noted above) - Button (reset) - I2C, which is needed for reading battery charge status and level - U-Boot environment / variables (from U-Boot, and OpenWrt) Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions I would like to thank @mpratt14 and @xabolcs for their help getting the lzma loader to work! Signed-off-by: Russell Morris <rmorris@rkmorris.us> [drop changes in image/Makefile, fix indent and PKG_RELEASE in uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift, add COMPILE to Device/Default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear JWNR2010 v5Shibajee Roy2020-08-062-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7620N (580 MHz) - Flash size: 4 MB NOR SPI - RAM size: 32 MB DDR1 - Bootloader: U-Boot - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz) - Switch: MT7620 built-in 10/100 switch with vlan support - Ports: 4x LAN, 1x WAN - Others: 7x LED, Reset button, UART header on PCB (57600 8N1) Flash instructions: 1. Use ethernet cable to connect router with PC/Laptop, any router LAN port will work. 2. To flash openwrt we are using nmrpflash[1]. 3. Flash commands: First we need to identify the correct Ethernet id. nmrpflash -L nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.) 4. Now remove the power cable from router back side and immediately connect it again. You will see flash notification in CMD window, once it says reboot the device just plug off the router and plug in again. Revert to stock: 1. Download the stock firmware from official netgear support[2]. 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware. nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img MAC addresses on stock firmware: LAN = *:28 (label) WAN = *:29 WLAN = *:28 On flash, the only valid MAC address is found in factory 0x4. Special Note: This openwrt firmware will also support other netgear N300 routers like below as they share same stock firmware[3]. JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050 [1] https://github.com/jclehner/nmrpflash [2] https://www.netgear.com/support/product/JWNR2010v5.aspx [3] http://kb.netgear.com/000059663 Signed-off-by: Shibajee Roy <ador250@protonmail.com> [create DTSI, use netgear_sercomm_nor, disable by default, add MAC addresses to commit message, add label MAC address] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-161-2/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix port display for TRENDnet TEW-810DRJ. Scott Heppler2020-06-121-1/+1
| | | | | | | | | | This updates the display port order for the TEW-810DR to be in line with the DIR-810L. Both share the same board and pictures on the vendors' pages indicate the same external numbering scheme as well. Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [replace commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix port display for D-Link DIR-810LAdrian Schmutzler2020-06-111-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | The port order displayed in LuCI is currently inverted for this devices: LuCI - Device LAN1 - LAN4 LAN2 - LAN3 LAN3 - LAN2 LAN4 - LAN1 Fix it. Strangely, the owner of a TRENDnet TEW-810DR reports that the initial port order is correct, while both devices share the same board and look similar from the outside. Since I cannot investigate this without having any of the devices, this does only touch the DIR-810L for now. While at it, also merge in the case for zbtlink,zbt-we2026, as the display port specified for WAN there won't have any effect anyway. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix WAN LED for D-Link DIR-810L/TRENDnet TEW-810DRAdrian Schmutzler2020-06-111-3/+4
| | | | | | | | | | | | | | | | | | The WAN LED on DIR-810L was actually blinking on LAN1 port activity. This has already been improved for the TEW-810DR, where the GPIO has been set up explicitly rather than having it controlled by the switch. This patch also applies this setup to the DIR-810L. In addition, the trigger in 01_leds is set up with ucidef_set_led_switch for both devices now, so state changes should be displayed correctly as well. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L] Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
* ramips: add support for Netgear EX6120Adrian Schmutzler2020-06-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * CPU: 580 MHz * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The device is identical to the EX6130 except for the mains socket and the hardware ID. Installation: The -factory images can be flashed from the device's web interface or via nmrpflash. Notes: MAC addresses were set up based on the EX6130 setup. This is based on prior work of Adam Serbinski and Mathias Buchwald. Tested by Mathias Buchwald. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TRENDnet TEW-810DRJ. Scott Heppler2020-05-262-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * MediaTek MT7620A (580 Mhz) * 8 MB of FLASH * 64 MB of RAM * 2.4Ghz and 5.0Ghz radios * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * UART header on PCB (57600 8n1) * Green/Orange Power LEDs illuminating a Power-Button Lens * Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens * 3x button - wps, power and reset * U-boot bootloader Installation: The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either the TEW-810DR or DIR-810L and is located at source/user/wolf/cameo/ncc/hostTools. The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0" This may need to be altered if your hardware version is "1.1R". The image can also be directly flashed via serial tftp: 1. Load *.sysupgrade.bin to your tftp server directory and rename for convenience. 2. Set a static ip 192.168.10.100. 3. NIC cable to a lan port. 4. Serial connection parameters 57600,8N1 5. Power on the TEW-810 and press 4 for a u-boot command line prompt. 6. Verify IP's with U-Boot command "printenv". 7. Adjust tftp settings if needed per the tftp documentation 8. Boot the tftp image to test the build. 9. If the image loads, reset your server ip to 192.168.1.10 and restart network. 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image. Notes: The only valid MAC address is found in 0x28 of the factory partition. Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [remove "link rx tx" in 01_leds, format and extend commit message, fix DTS led node names] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default switch setup in 02_networkChuanhong Guo2020-05-191-12/+8
| | | | | | | | ramips images now relies on explicit switch setup for proper failsafe functionality. Remove default cases where it relies on vlan setup in dts and add switch setup for devices affected. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: set WAN address in DTS for ASUS RT-AC51U/RT-AC54UAdrian Schmutzler2020-05-181-2/+1
| | | | | | | | | | | | | The location 0x28 in factory partition is the common one used for ethernet address on this architecture. Despite, it contains the label MAC address for the devices at hand. Consequently, this patch moves 0x28 to the &ethernet node in DTS files (setting the WAN MAC address there) and sets up the lan_mac from 0x22 in 02_network. As a benefit, this allows to use label-mac-device in DTS instead of ucidef_set_label_macaddr. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2025-07-24 18:10:45 +0000