aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
* ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027Sungbo Eo2020-04-271-1/+0
| | | | | | | | kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and Belkin F7C027 does not have a USB port anyway. Just drop it. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit 1dedad2a00d8519d4892b8529b5f2fffcb768220)
* Revert "ramips: disable ZyXel Keenetic by default"Adrian Schmutzler2020-04-121-1/+0
| | | | | | | | | This reverts commit c38074de929e6f7c089e2cb7f81746ba90ddf16b. Since ZyXEL Keenetic has actually 8 MiB flash as fixed in the previous patch, we can re-enable it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use full 8MB flash on ZyXEL KeeneticAlexey Dobrovolsky2020-04-121-1/+1
| | | | | | | | | | | | | | | | | ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB. This commit fixes the problem. WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is an article with specs [2] (in Russian). [1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic [2] https://3dnews.ru/608774/page-2.html Fixes: FS#2487 Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> (cherry picked from commit fea232ae8feb6af780fd4fa78ebe9231778bf75a)
* ramips: append tail to WF2881 initramfs imageSungbo Eo2020-02-211-0/+8
| | | | | | | | | | | | | Stock firmware has a vendor-defined tail at the end of uImage for image validation. This patch enables OpenWrt installation from stock firmware without having to access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit be3e98ce26da5e737744427e1d59dd1c0508edef)
* ramips: reenable image creation for the D-Link DIR-645Mason Clarke2020-02-011-1/+0
| | | | | | | | | | | | | | | | | | | This commit reenables the image creation for the D-Link DIR-645. Images built for the D-Link DIR-645 work just fine, there is no reason to disable the image creation for it. I tested the OpenWrt 18.06.5 and 19.07.0-rc1 images, as well as an image I built from the current 19.07 branch (git HEAD 62d5ece) with the default 19.07 release config, and I cannot confirm the report that commit 2607c02ed599b6118ba26e2f35e7c828c21d7275 ("ramips: disable D-Link DIR-645 by default") references. Configuration changes were applied successfully and remained set after a reboot as well. The log also showed no anomalies. This reverts commit 2607c02ed599b6118ba26e2f35e7c828c21d7275. Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
* ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20iAdrian Schmutzler2020-01-291-1/+0
| | | | | | | | | | DEVICE_PACKAGES is specified twice for the same device. Remove the first (=older) assignment. Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 4ecd6510bf8877dcd07561045852726ffbab8814)
* ramips: mt7621: ubnt-erx: allow sysupgrade from masterPetr Štetiar2020-01-241-0/+2
| | | | | | | | | | | | Currently it's not possible to downgrade from master: Device ubiquiti,edgerouterx not supported by this image Supported devices: ubnt-erx So fix it by adding a DTS based device name from master into SUPPORTED_DEVICES list. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add factory image for Netgear R6350Christoph Krapp2020-01-211-1/+6
| | | | | | | | | | | | | | This adds factory image generation for all three devices. These images can be flashed via WebUI for easy installation. Thanks to David Bauer for the inspiration. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [altered commit to only include the R6350] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 3c8df280a96bbd81357d6eb52845e6b5fa7162fe) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add mt7615e support to Netgear R6350Christoph Krapp2020-01-211-1/+1
| | | | | Signed-off-by: Christoph Krapp <achterin@googlemail.com> (cherry picked from commit 9861fa7abab97cb928aaa6cd5732a413d973ac95)
* ramips: add kmod-mt7615e to Xiaomi Mi Router 3 Pro imagesOzgur Can Leonard2020-01-181-1/+2
| | | | | | | Now that the mt76/mt7615e driver is in Openwrt, might as well use it. Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> (cherry picked from commit d7c082ba4f7de97b3708d1f4a064954ffc774778)
* ramips: mt7621: disable images for gehua_ghl-r-001Petr Štetiar2020-01-141-0/+1
| | | | | | | | | | | This device OOPs during the boot due to broken flash. It can be probably fixed with `broken-flash-reset` once ramips is on 4.19 kernel. So disable images for this device until its fixed. Ref: FS#2695, PR#2483 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 28080d54d217fb4ab112e079f69462fee695dbf8)
* ramips: Fix sysupgrade for Xiaomi mir3gHauke Mehrtens2020-01-061-3/+4
| | | | | | | | | | | | | | | | | | | This mostly reverts the original commit e9929ebeeaef ("ramips: Fix sysupgrade for Xiaomi mir3g") and replaces it with setting the BOARD_NAME to the old value. This way the folder in the tar will be named sysupgrade-mir3g and not sysupgrade-xiaomi_mir3g and the sysupgrade in OpenWrt 18.06 can find it. Without this change sysupgrade from 18.06 to 19.07 is only possible with the -F option. I tested the following sysupgrades successfully without -F 18.06 -> 19.07 19.07 -> master master -> 19.07 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: Fix sysupgrade for Xiaomi mir3gHauke Mehrtens2020-01-051-3/+3
| | | | | | | | | | | | | | | | | Without this change sysupgrade from 18.06 to 19.07 is only possible with the -F option. In OpenWrt 18.06 the nand_do_platform_check() function is called with the board name mir3g only, if the tar does not use mir3g it will fail. OpenWrt 19.07 and later support the metadata with the supported_devices attribute to allow renaming. Do the renaming of the target between 19.07 and master like it is done for some other boards. I tested the following sysupgrades successfully without -F 18.06 -> 19.07 19.07 -> master master -> 19.07 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: allow JCG_MAXSIZE in kiB in Build/jcg-headerAdrian Schmutzler2019-12-132-2/+4
| | | | | | | | | | | | | | | This allows JCG_MAXSIZE to be specified in kilobytes. This makes this value more consistent and easier comparable with other size variables. This also changes the only occurence of the variable, for Cudy WR1000. This is backported to 19.07 for convenience, as other developers backporting device support might not be aware that JCG_MAXSIZE in kilobytes would not work there. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 0bf4d681d4f2e4bd3c3a61e7fe5dca2a40b1902f)
* ramips: disable ZyXel Keenetic by defaultJo-Philipp Wich2019-11-301-0/+1
| | | | | | | | Disable the ZyXel Keenetic images by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable WR512-3GN 4MB variant by defaultJo-Philipp Wich2019-11-301-0/+1
| | | | | | | | Disable the WR512-3GN 4MB image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable A5-V11 by defaultJo-Philipp Wich2019-11-301-0/+1
| | | | | | | | Disable the A5-V11 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable TP-Link TL-WR840N v5 by defaultJo-Philipp Wich2019-11-291-0/+1
| | | | | | | | Disable the TP-Link TL-WR840N v5 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/29 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable Sitecom WL-351 by defaultJo-Philipp Wich2019-11-291-0/+1
| | | | | | | | Disable the Sitecom WL-351 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/24 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable D-Link DIR-645 by defaultJo-Philipp Wich2019-11-291-0/+1
| | | | | | | | Disable the D-Link DIR-645 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/23 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable D-Link DIR-300 B5/B6/B7 by defaultJo-Philipp Wich2019-11-291-0/+1
| | | | | | | | Disable the D-Link DIR-300 B5/B6/B7 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/18 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: disable ASUS RT-N10+ B1 by defaultJo-Philipp Wich2019-11-291-0/+1
| | | | | | | | Disable the ASUS RT-N10+ B1 image by default as the device has insufficient flash space for release build images. Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/1 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM, USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support. Specification: - MT7621A (880 MHz) - 256/512 MB of RAM (DDR3) - 16/32+ MB of FLASH (SPI NOR) - optional second SPI flash (8-pin WSON/SOIC) - 1x microSD (SDXC) flash card reader - 5x 10/100/1000 Mbps Ethernet, with passive PoE support (24 V) in LAN1 - optional 802.3at/af PoE module for WAN - 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V) - 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM) - RTC (TI BQ32002, I2C bus) with backup battery (CR2032) - external hardware watchdog (EM Microelectronic EM6324) - 1x USB 2.0 Type-A - 1x micro USB Type-B for system serial console (Holtek HT42B534) - 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator) - 3x button (reset, user1, user2) - 1x I2C (4-pin, 2.54 mm pitch) header on PCB - 4x SIM (6-pin, 2.00 mm pitch) headers on PCB - 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB - 1x mechanical power switch - 1x DC jack with lock (24 V) Other: - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board has additional logic circuit for M.2 SIM switching. The 'sim-select' will work only if both SIM slots are occupied. Otherwise, always slot with SIM inside is selected, no matter 'sim-select' value. - U-Boot enables power in all three miniPCIe and M.2 slots before loading the kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) - all three miniPCIe slots have additional 5 V supply on pins 47 and 49 - the board allows to install up to two oversized miniPCIe cards (vendor has dedicated MediaTek MT7615N/D cards for this board) - this board has additional logic circuit controlling PERSTn pins inside miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe slots but setting GPIO22 to high allows PERSTn control per slot, using GPIO23-25 (value is inverted) Flash instructions: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit e68539aca43a560077364de27eb220f1d85ca3ef)
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-241-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit dfecf94c2059998411f95067de3866aa7cdf5ec9)
* ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTBChuanhong Guo2019-11-243-10/+5
| | | | | | | | | | | | | | | | | | | Upstream kernel added support for RAW_APPENDED_DTB on ralink arch in the following commit: 02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink") Use upstream solution and get rid of our OWRTDTB hack. This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with DEVICE_DTS in device profile because DTS variable will be dropped in later commits. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Tested on mt7621/mt76x8] Tested-by: Chuanhong Guo <gch981213@gmail.com> [Tested on rt305x/mt7620] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit 7a8d3432c739c6ff038295176e8b6324e92fc116) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: set uImage name of WeVO 11AC NAS and W2914NS v2Sungbo Eo2019-11-211-0/+2
| | | | | | | | | | | | | | | | The stock firmware and bootloader only accept uImage with names that match certain patterns. This patch enables OpenWrt installation from stock firmware without having to reflash the bootloader or access the UART console. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit 19800ac095f6ddbba03ccab08e5197b1eec4a49e) [backported] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: disable D-Link DIR-300 B1 by defaultJo-Philipp Wich2019-11-161-0/+1
| | | | | | | | Disable the DIR-300 B1 image by default as the device has insufficient flash space for release build images. Fixes: FS#2606 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: rt3833: fix build breakagePetr Štetiar2019-11-151-1/+1
| | | | | | | | | | | | Commit 60f41c6c9ef6 ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100") added stray | during backport which caused build breakage on the buildbots: bash: -c: line 0: syntax error near unexpected token `|' bash: -c: line 0: `echo kmod-usb-core kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 swconfig | | mkhash md5 | head -c 8' Fixes: 60f41c6c9ef6 ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100Sungbo Eo2019-11-141-1/+2
| | | | | | | | | | CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing in default images. This commit adds it. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [changed commit title, backported to 19.07] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 261c746631d2bf311a6b62a6d3bacce6fde90976)
* ramips: add factory image for NETGEAR R6220David Bauer2019-09-161-1/+6
| | | | | | | | | | | This adds an easy-installation factory image for the NETGEAR R6220 router. The factory image can either be flashed via the vendor Web-UI or the bootloader using nmrpflash. Tested with NETGEAR V1.1.0.86 firmware. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 607dfdf211bebb5043cbc0267c1e2c3e3c2514b4)
* mt7620: disable image generation for Nexx WT3020 (4MB)Hauke Mehrtens2019-09-081-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file openwrt-19.07-snapshot-r10495-db5164d3d0-ramips-mt7620-wt3020-4M-squashfs-factory.bin is too big Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for ASUS RT-AC57UDavid Bauer2019-07-211-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 14e0e4f138e35c3e2a15cc3a836c939547ee053b)
* mt7620: disable image generation for Netgear EX2700Petr Štetiar2019-07-201-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TOTOLINK LR1200Chuanhong Guo2019-06-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7628DAN (MT7628AN with 64MB built-in RAM) - Flash: 8M SPI NOR - Ethernet: 5x 10/100Mbps - WiFi: 2.4G: MT7628 built-in 5G: MT7612E - 1x miniPCIe slot for LTE modem (only USB pins connected) - 1x SIM slot Flash instruction: U-boot has a builtin web recovery page: 1. Hold the reset button while powering it up 2. Connect to the ethernet and set an IP in 192.168.1.0/24 range 3. Open your browser and upload firmware through http://192.168.1.1 Note about the LTE modem: If your router comes with an EC25 module and it doesn't show up as a QMI device, you should do the following to switch it to QMI mode: 1. Install kmod-usb-serial-option and a terminal software (e.g. minicom or screen). All 4 serial ports of the modem should be available now. 2. Open /dev/ttyUSB3 with the terminal software and type this AT command: AT+QCFG="usbnet",0 3. Power-cycle the router. You should now get a QMI device recognized. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: create R6220 dtsi and improve WNDR3700v5 supportJan Hoffmann2019-05-311-1/+2
| | | | | | | | | | | | | | | | | | The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and having a different casing. This adds a new cleaned up R6220.dtsi with the common bits for both devices. Both devices now have feature parity. Performed cleanup: * generic DTS node names * regulator for usb power * added missing pinctrl groups * use switch port instead of VLAN as trigger for WAN LED Fixes for WNDR3700v5: * all LEDS work * correct ethernet MAC addresses Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Xiaomi Mi Router 4A (100M Edition)Markus Scheck2019-05-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - SoC: MediaTek MT7628AN - Flash: 16MB (Winbond W25Q128JV) - RAM: 64MB - Serial: As marked on PCB, 3V3 logic, baudrate is 115200 - Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN) - WIFI0: MT7628AN 2.4GHz 802.11b/g/n - WIFI1: MT7612EN 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable power-LED (two-colored, yellow/blue) Non-programmable internet-LED (shows WAN-activity) - Buttons: Reset INSTALLATION: 1. Connect to the serial port of the router and power it up. If you get a prompt asking for boot-mode, go to step 3. 2. Unplug the router after > Erasing SPI Flash... > raspi_erase: offs:20000 len:10000 occurs on the serial port. Plug the router back in. 3. At the prompt select option 2 (Load system code then write to Flash via TFTP.) 4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the Server-IP. 5. Connect your computer to LAN1 and assign it as 192.168.1.2/24. 6. Rename the sysupgrade image to test.bin and serve it via TFTP. 7. Enter test.bin on the serial console and press enter. Signed-off-by: Markus Scheck <markus@mscheck.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added mt76 compatible]
* ramips: add CUDY WR1000 supportDavide Fioravanti2019-05-311-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas Specifications: MT7628 (580 MHz) 64 MB of RAM (DDR2) 8 MB of FLASH 2T2R 2.4 GHz (MT7628) 2T2R 5 GHz (MT7612E) 3x 10/100 Mbps Ethernet (2 LAN + 1 WAN) 2x external, non-detachable antennas (5dbi) UART header on PCB (57600 8n1) 7x LED, 2x button Known issues: The Power LED is always ON, probably because it is connected directly to power. Flash instructions ------------------ Load the ...-factory.bin image via the stock web interface. Openwrt upgrade instructions ---------------------------- Use the ...-sysupgrade.bin image for future upgrades. Revert to stock FW ------------------ Warning! This tutorial will work only with the following OEM FW: WR1000_EU_92.122.2.4987.201806261618.bin WR1000_US_92.122.2.4987.201806261609.bin If in the future these firmwares will not be available anymore, you have to find the new XOR key. 1) Download the original FW from the Cudy website. (For example WR1000_EU_92.122.2.4987.201806261618.bin) 2) Remove the header. dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64 3) XOR the new file with the region key. FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this: xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767.. Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!): https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false) 4) Check the resulting decrypted image. Check if bytes from 0x20 to 0x3f are: 4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Alternatively, you can use u-boot's tool dumpimage tool to check if the decryption was successful. It should look like: # dumpimage -l stock-firmware.bin Image Name: Linux Kernel Image Created: Tue Jun 26 10:24:54 2018 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB Load Address: 80000000 Entry Point: 8000c150 5) Flash it via forced firmware upgrade and don't "Keep Settings" CLI: sysupgrade -F -n stock-firmware.bin LuCI: make sure to click on the "Keep settings" checkbox to disable it. You'll need to do this !TWICE! because on the first try, LuCI will refuse the image and reset the "Keep settings" to enable. However a new "Force upgrade" checkbox will appear as well. Make sure to do this very carefully! Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added wifi compatible, spiffed-up the returned to stock instructions]
* ramips: unify JCG helper command definitionDavide Fioravanti2019-05-312-5/+6
| | | | | | | This patch makes the JCG helper command definition available for every rampis target Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for Telco Electronics X1Nicholas Smith2019-05-181-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 256MB DDR3 Flash: 16MB SPI-NOR WiFi: 2.4GHz: MT7603 @ PCIe0 WiFi: 5.8GHz: MT7612 @ PCIe1 Modem: Sierra Wireless MC74xx Interfaces: GBE RJ45 x5 mPCIe x2 UART x1 I2C x1 JTAG x1 UIM x1 LEDs x6 Flash instructions: Flash from within the factory bootloader, firmware web interface or CLI using sysupgrade -F -n Signed-off-by: Nicholas Smith <mips171@icloud.com>
* ramips: add factory image for WNDR3700v5Jan Hoffmann2019-05-183-17/+24
| | | | | | | | | This uses the existing rules for Sercomm factory images and moves them to the ramips image Makefile, so they can be used in all subtargets. The new factory image for WNDR3700v5 can be flashed using nmrpflash. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for HILINK HLK-7628NLiu Yu2019-05-181-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 128 MB Flash: 32 MB WIFI: 802.11n/g/b 20/40 MHz Ethernet: 5 Port ethernet switch UART: 2x Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART0 line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. 5. After firmware is started connect via ethernet at 192.168.1.1 Signed-off-by: Liu Yu <f78fk@live.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-171-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix R6120 factory imageDavid Bauer2019-05-111-1/+1
| | | | | | | | | | | The factory firmware omits the JFFS2 end-marker while flashing via web-interface. Add a 64k padding after the marker fixes this problem. When the end-marker is not present, OpenWRT won't save the overlayfs after initial flash. Reported-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-141-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-131-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-061-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* ramips: add Netgear EX6150David Bauer2019-03-291-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621 RAM: 64M (Winbond W9751G6KB-25) FLASH: 16MB (Macronix MX25L12835F) WiFi: MediaTek MT7662E bgn 2SS WiFi: MediaTek MT7662E nac 2SS BTN: ON/OFF - Reset - WPS - AP/Extender toggle LED: - Arrow Right (blue) - Arrow Left (blue) - WiFi 1 (red/green) - WiFi 2 (red/green) - Power (green/amber) - WPS (Green) UART: UART is present as Pads on the backside of the PCB. They are located on the other side of the Ethernet port. 3.3V - GND - TX - RX / 57600-8N1 3.3V is the nearest one to the antenna connectors Installation ------------ Update the factory image via the Netgear web-interfaces (by default: 192.168.1.250/24). You can also use the factory image with the nmrpflash tool. For more information see https://github.com/jclehner/nmrpflash Signed-off-by: David Bauer <mail@david-bauer.net> [merge conflict in 02_network, flash@0 node rename, wlan DTS triggers] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ZyXEL Keenetic StartVladimir Kot2019-03-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: RT5350F - CPU Frequency: 360 MHz - Flash Chip: Winbond 25Q32 (4096 KiB) - RAM: 32768 KiB - 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) - 1x external, non-detachable antenna - UART (J1) header on PCB (57800 8n1) - Wireless: SoC-intergated: 2.4GHz 802.11bgn - USB: None - 3x LED, 2x button Flash instruction: 1. Configure PC with static IP 192.168.1.2/24 and start TFTP server. 2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin" to "kstart_recovery.bin" and place it in TFTP server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. 4. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Vladimir Kot <vova28rus@gmail.com> [fixed git commit author and whitespace issues in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 07:19:49 +0000