aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1Alex Khodin2022-10-231-0/+1
| | | | | | | | Fixes boot loader LZMA decompression issues. Without this change the board end up in a boot loop. Signed-off-by: Alex Khodin <mxktz1@gmail.com>
* ramips: add A-040W-Q alternative name for MSG1500 X.00Chukun Pan2022-10-231-0/+2
| | | | | | | The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are exactly the same, both of which are customized by operators. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* build: move Build/edimax-header to image-commands.mkINAGAKI Hiroshi2022-10-191-5/+0
| | | | | | | | | | To use from the following devices in ath79 target, move edimax-header to image-commands.mk. - ELECOM WRC-300GHBK2-I - ELECOM WRC-1750GHBK2-I/C Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mt7621: netgear_ex6150: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #10645 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: use lzma-loader on JCG Q20Du Cai2022-10-091-0/+1
| | | | | | Fixes the LZMA uncompression issue on JCG Q20. Signed-off-by: Du Cai <caidu@smail.nju.edu.cn>
* ramips: add support for SNR SNR-CPE-ME2-LiteAlexey Kosmakov2022-10-021-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR SNR-CPE-ME2-Lite is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4 GHz 2T2R (MediaTek MT7603E) 5 GHz 2T2R (MediaTek MT7613BE) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction via WEB (firmware 1.10.4 and later) 1. Boot SNR-CPE-ME2-Lite normally with "Router" mode 2. Access to "http://192.168.1.1/" and open "Administration -> Management" page 3. Select the OpenWrt factory image in "Firmware update" section and click "Update" button 4. Wait ~120 seconds to complete flashing Flash instruction via TFTP (all version): 1. Boot SNR-CPE-ME2-Lite to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Kosmakov <a.kosmakov@nagtech.ru>
* ramips: enable LZMA loader to fix Linksys RE6500 bootMark King2022-10-021-0/+1
| | | | | | | | | | | At some point after 21.02.3 and before 22.03.0, the size limits of the Linksys RE6500 were reached and prevent booting from the 22.03.0 release or builds of current SNAPSHOT. This patch allows builds of master to boot again and has been tested on my device. Fixes: #8577 Signed-off-by: Mark King <mark@vemek.co>
* ramips: add led driver to UniFi FlexHD defaut package setDaniel Golle2022-09-301-1/+1
| | | | | | | Add kmod-leds-ubnt-ledbar to the packages selected by default on the UniFi FlexHD access point. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for ZyXEL Keenetic 4G Rev.B DeviceSergei Burakov2022-09-131-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | Specification: SoC: RT5350 CPU Frequency: 360 MHz Flash Chip: Macronix MX25L6406E (8192 KiB) RAM: Winbond W9825G6JH-6 (32768 KiB) 3x 10/100 Mbps Ethernet (2x LAN, 1x WAN) 1x external antenna UART (J1) header on PCB (57800 8n1) Wireless: SoC-intergated: 2.4GHz 802.11bgn USB: Yes 8x LED, 2x button Flash instruction: Configure PC with static IP 192.168.99.8/24 and start TFTP server. Rename "openwrt-ramips-rt305x-zyxel_keenetic-4g-b-squashfs-sysupgrade.bin" to "rt305x_firmware.bin" and place it in TFTP server directory. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Sergei Burakov <senior.anonymous@mail.ru>
* ramips: use lzma-loader on Sitecom WLR-6000Jasper Scholte2022-09-111-0/+1
| | | | | | | Fixes the boot loader LZMA decompression issue: LZMA ERROR 1 - must RESET board to recover Signed-off-by: Jasper Scholte <NightNL@outlook.com>
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-111-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
* ramips: add support for Linksys E7350Rosen Penev2022-09-111-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Belkin RT1800Rosen Penev2022-09-111-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add RT-N600 alternative name to RT-AC1200Ray Wang2022-09-111-0/+2
| | | | | | | | RT-N600 is internally the same as RT-AC1200, as veryfied by @russinnes . Adding alt_name so that people can find it in firmware selector. Signed-off-by: Ray Wang <raywang777@foxmail.com> Tested-by: Russ Innes <russ.innes@gmail.com>
* ramips: add support for Kroks Rt-Cse SIM Injector DSAndrey Butirsky2022-09-111-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: add support for Kroks Rt-Pot mXw DS RSIM routerAndrey Butirsky2022-09-111-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-201-0/+2
| | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: get MAC addr from the encrypted partition (WG4хх223)Mikhail Zhilkin2022-08-191-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223 configuration partition (board_data)to get base MAC address from it. As a result, after this change the hack with saving MAC addressees to u-boot-env before installation of OpenWrt is no longer necessary. This is necessary for the following devices: - Beeline Smartbox Flash (Arcadyan WG443223) - MTS WG430223 (Arcadyan WG430223) Example: +----------------+-------------------+------------------------+ | | MTS WG430223 | Beeline Smartbox Flash | +----------------+-------------------+------------------------+ | base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 | | LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 | | WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 | | WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 | +----------------+-------------------+------------------------+ Collected statistic shows that the 2-4th bits of the 7th byte of the WLAN_5g MAC are the constant (see #10062 for more details): - Beeline Smartbox Flash - 100 - MTS WG430223 - 010 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Beeline SmartBox TURBOMikhail Zhilkin2022-08-131-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 Button: 2 buttons (Reset & WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (admin:admin) 2. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where SNxxxxxxxxxx is the serial number from the backplate label) 6. Run in SSH shell: sh 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface (admin:admin) 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- 1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:54 | | WAN | label + 1 | *:55 | | 2g | label + 4 | *:58 | | 5g | label + 5 | *:59 | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Co-developed-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ZyXEL LTE3301-PlusAndré Valentin2022-08-061-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7615E - Switch: 4 LAN ports (Gigabit) - LTE: Quectel EG506 connected by USB3 to SoC - SIM: 1 micro-SIM slot - USB: USB3 port - Buttons: Reset, WPS - LEDs: Multicolour power, internet, LTE, signal, Wifi, USB - Power: 12V, 1.5A The device is built as an indoor ethernet to LTE bridge or router with Wifi. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc MAC assignment: lan: 98:0d:67:ee:85:54 (base, on the device back) wlan: 98:0d:67:ee:85:55 Installation from web GUI: - Log in as "admin" on http://192.168.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - format ubi device: ubiformat /dev/mtd6 - attach ubi device: ubiattach -m6 - create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB - rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB - run sysupgrade with sysupgrade image For more details about flashing see commit 2449a632084b ("ramips: mt7621: Add support for ZyXEL NR7101"). Please note that this commit is needed: firmware-utils: add marcant changes for ZyXEL NBG6716 and LTE3301-PLUS Signed-off-by: André Valentin <avalentin@marcant.net>
* ramips: add support for Netcore NW5212David Yang2022-08-061-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netcore NW5212, provided by some carrier in China. Specifications: -------------- * SoC: Mediatek MT7620A * RAM: 128MB DDR2 * Flash: 16MB SPI NOR flash (Winbond W25Q128BV) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, WAN, LAN 1-4, WiFi * Buttons: Reset (GPIO 13) * UART: Serial console (57600 8n1) * USB: 1 x USB2 Installation: ------------ The router comes with OpenWrt 14.07 built with MTK SDK. However, as the modem is provided by carriers, so the web interface is highly minimized and only contains a static page with no interaction options. There are two possible ways to gain the access. 1) Open the shell and use a UART2USB convert to gain TTY access. Please notice you have to remove resistance R54 at the back of the board otherwise you won't be able to input anything. 2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to start dropbear service at port 9122. Be warned the software is super old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1, kexguess2@matt.ucc.asn.au is support, you may not be able to connect it with an up-to-date ssh client. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via original firmware): 1) Setup HTTP server on your computer, for example: python3 -m http.server 2) Connect to the route and flash: cd /tmp wget http://<your-computer-host>/<your-firmware-name> mtd -r write <your-firmware-name> firmware Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset13.bin mtd write breed-mt7620-reset13.bin Bootloader 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose the flash layout to be 0x50000 and flash new firmware. MAC addresses: ------------- There are three MACs stored in factory, as in MT7620A reference design: source address usage 0x4 label WLAN 0x28 label MAC 1 0x2e label + 1 MAC 2 However, the OEM firmware only uses one single MAC (label) for all interfaces, probably a misconfiguration. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: add support for Netgear PR2000David Yang2022-08-061-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear PR2000, sold as "Travel Router and Range Extender". Specifications: -------------- * SoC: Mediatek MT7620N * RAM: 64MB DDR2 * Flash: 16MB SPI NOR flash (Macronix MX25L12805D) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, Internet, WiFi, USB * Buttons: Reset (GPIO 1/2) * UART: Serial console (57600 8n1) * USB: 1 x USB2 SPECIAL NOTES: ------------- Problem: WiFi is super weak, but SSID beacons seems to be right. Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0. Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2 of 36h indicates the presence of External LNA for 11g (2.4 GHz) band, which seems to be incorrectly set by Netgear (originally 0x04). Lifting it solves the problem of weak RX signal. Installation: ------------ There are two possible ways to install the firmware. Flashing via web interface of original firmware is not tested due to a broken firmware. 1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD, TP9: TXD, TP10: GND). Please notice you have to remove resistance R54 next to TP7 otherwise you won't be able to input anything. 2) Use well-known Netgear debug switch. Access http://192.168.168.1/setup.cgi?todo=debug to start telnet service (username: root, password: <none>). Please back up firmware if you want to go back to the original. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via nmrpflash): 1) Download nmrpflash from https://github.com/jclehner/nmrpflash 2) Use *-factory.img and flash: nmrpflash -L nmrpflash -i net* -f <your-firmware-name> 3) Turn off then turn on the device, wait it finishing flash. Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset1.bin dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose memory layout to be 0x40000 and flash new firmware. Remark: ------ As a "Range Extender", it has a switch to switch between Wired mode (GPIO 21 low) and Wireless mode (GPIO 20 low), which is not implemented in this patch. However, the router will be turned off when it switches to the middle, which makes this switch much less useful. MAC addresses: ------------- The OEM firmware uses one single MAC for all interfaces, located at 0xf700b0. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: adding support for Asus RP-AC56Lea Teuberth2022-08-061-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: CPU: MT7621A dual-core 880MHz RAM: 64MB DDR2 FLASH: 16MB MX25L12805D NOR SPI WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI WIFI: 5GHz 2x2 MT7662 a/b/ac PCI ETH: 1xLAN 1000base-T integrated SWITCH: MT7530 Port 0: LAN, Port 6: CPU LED: Power, 2.4GHz WiFi, 5GHz WiFi BTN: WPS, Reset UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1 MISC: Audio support Installation: 1. Update using recovery mode - while holdig "reset" button, power on the device - keep holding "reset" until power led is flashing yellow - set own IP to 192.168.1.75, subnet mask: 255.255.255.0 - push firmware image (can be factory.bin or sysupgrade.bin) using tftp client in binary mode to 192.168.1.1 Notes: This board has only two MAC addresses programmed in the "factory" partition: - MAC for wlan0 (2.4GHz) at offset 0x0004 - MAC for wlan1 (5GHz) at offset 0x8004 - stock firmware re-uses wlan0 MAC for ethernet - no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006 Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
* ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806Shiji Yang2022-07-311-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | H3C TX180x series WiFi6 routers are customized by different carrier. While these three devices look different, they use the same motherboard inside. Another minor difference comes from the model name definition in the u-boot environment variable. Specifications: SOC: MT7621 + MT7915 ROM: 128 MiB RAM: 256 MiB LED: status *2 Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP server IP: 192.168.124.99 MAC Address: use address(sample 1) address(sample 2) source label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1 wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode) WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode) WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7 WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7 Compatibility mode is used to guarantee the connection of old devices that only support WiFi4 or WiFi5. TFTP + TTL Installation: Although a TTL connection is required for installation, we do not need to tear down it. We can find the TTL port from the cooling hole at the bottom. It is located below LAN3 and the pins are defined as follows: |LAN1|LAN2|LAN3|----|WAN| -------------------- |GND|TX|RX|VCC| 1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in server's root directory, rename it to a simple name "initramfs.bin". 2. Plug in the power supply and wait for power on, connect the TTL cable and open a TTL session, enter "reboot", then enter "Y" to confirm. Finally push "0" to interruput boot while booting. 3. Execute command to install a initramfs system: # tftp 0x80010000 192.168.124.99:initramfs.bin # bootm 0x80010000 4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those partitions if we want to back to stock firmwre due to official website does not provide download link. # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin # dd if=/dev/mtd4 of=/tmp/firmware.bin 5. Edit u-boot env to ensure use default bootargs and first image slot: # fw_setenv bootargs # fw_setenv bootflag 0 6. Upgrade sysupgrade firmware. 7. About restore stock firmware: flash the "firmware" and "u-boot-env" partitions that we backed up in step 4. # mtd write /tmp/u-boot-env.bin u-boot-env # mtd write /tmp/firmware.bin firmware Additional Info: The H3C stock firmware has a 160-byte firmware header that appears to use a non-standard CRC32 verification algorithm. For this part of the data, the u-boot does not check it so we can just directly replace it with a placeholder. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-07-201-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear WAX202Wenli Looi2022-07-191-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-07-031-0/+10
| | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com>
* ramips: Add suport for COMFAST CF-WR617ACSergei Iudin2022-07-031-0/+9
| | | | | | | | | | | | | | | | | Specifications: Chipset:MT7628DA+MT7612E Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps Output Power :100mW(20dbm) Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port Flash: 8Mb DRam: 64Mb Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1 Known issues: mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition. Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
* ramips: add support for Beeline SmartBox GIGAMikhail Zhilkin2022-07-033-2/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ASUS RP-AC87Tamas Balogh2022-06-291-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC87 ac2600 Repeater 2.4GHz 800Mbps 5GHz 1733Mbps Hardware specifications: SoC: MT7621A 2 cores 4 threads @880MHz WiFi2G: MT7615E 2G 4x4 b/g/n Wifi5G: MT7615E 5G 4x4 n/ac DRAM: 128MB DDR3 @1200mhz Flash: 16MB MX25L12805D SPI-NOR LAN/WAN: MT7530 1x1000M MAC addresses as verified by OEM firmware: use address source Lan/W5G *:B0 factory 0x8004 (label) W2G *:B4 factory 0x0 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.2 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for Asus RT-N12+ B1 and RT-N300 B1Semih Baskan2022-06-251-0/+6
| | | | | | | | | | | | | | Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device with a different name. The OEM firmwares have the same MD5 with Asus RT-N11P B1. Same instructions for Asus RT-N11P B1 see: commit c3dc52e39ac8 ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1") Signed-off-by: Semih Baskan <strstgs@gmail.com> (Added id from the PR review to commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-06-251-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: fix booting on ZyXEL NBG-419N v2Piotr Dymacz2022-06-201-0/+1
| | | | | | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of other devices from 'ramips' target. Fixes: #9842 Fixes: #8964 Reported-by: Juergen Hench <jurgen.hench@gmail.com> Tested-by: Juergen Hench <jurgen.hench@gmail.com> Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-131-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: allow custom trx magic for ArcadyanMikhail Zhilkin2022-06-131-3/+4
| | | | | | | | | | | | This commit: 1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe is necessary for: - MTS WG430223 (Arcadyan WG430223) - Beeline Smartbox Flash (Arcadyan WG443223) 2. Allows specify custom trx magic which is different for the routers mentined above. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-161-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: fix booting on Samknows SK-WB8Piotr Dymacz2022-05-131-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #9824 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-091-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-04-301-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-04-231-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-04-231-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* ramips: add support for OrayBox X3ARay Wang2022-04-171-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-161-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-161-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-161-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add linux 5.15 support for mt7621Felix Fietkau2022-03-271-0/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for D-Link DIR-878 R1Igor Nazarov2022-03-191-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) - Switch: 1 WAN, 4 LAN (Gigabit) - Buttons: Reset, WiFi Toggle, WPS - LEDs: Power, Internet, WiFi 2.4G WiFi 5G The R1 revision is identical to the A1 revision except - No Config2 Parition, therefore - factory partition resized to 64k from 128K - Firmware partition offset is 0x50000 not 0x60000 - Firmware partitions size increased by 64K - Firmware partition type is "denx,uimage", not "sge,uimage" - Padding of image creation "uimage-padhdr 96" removed Installation: Update to the last D-Link firmware through web-ui before OpenWRT installation then follow the instructions to patch your device using D-Link FailsafeUI. - D-Link FailsafeUI: Power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing, then jack into any lan port and manually assign a static IP address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2) and go to http://192.168.0.1 Flash with the factory image. Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-191-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Netgear WN3100RPv2Rodolphe de Saint Léger2022-03-161-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
generated by cgit v1.2.3 (git 2.25.1) at 2025-04-13 01:24:07 +0000