aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7621.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: RT1800: fix invalid octal number errorMax Qian2023-09-171-1/+1
| | | | | | | | | | | This commit removes the padded zeros in the date formatting. The padded zeros from the date command causes the numbers to be interpreted as an octal number by printf. Months, days, and years with the number 08 or 09 raise an error in printf as an "invalid octal number" and get interpreted as a zero. Signed-off-by: Max Qian <public@maxqia.com> (cherry picked from commit 794349a28a7b9036b54e13487a96120609db924e)
* ramips: add support for ALFA Network AX1800RMPiotr Dymacz2023-09-111-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6 (AX1800) router, based on MediaTek MT7621A + MT79x5D platform. Specifications: - SOC: MT7621A (880 MHz) - DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK) - Flash: 16 MiB SPI NOR (EN25QH128A-104HIP) - Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch) - Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN) (MT7905DAN doesn't support background DFS scan/BT) - LED: 6x green, 1x green/red - Buttons: 2x (reset, WPS) - Antenna: 4x external, non-detachable omnidirectional - UART: 1x 4-pin (2.54 mm pitch, J4, not populated) - Power: 12 V DC/1 A (DC jack) MAC addresses: LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2) WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3) 2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label) 5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa) Flash instructions for web-based U-Boot recovery: 1. Power the device with WPS button pressed and wait around 10 seconds. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'recovery' image. The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe' mode available which allows alternative upgrade method: 1. Run device in 'failsafe' mode and change password for default user. 2. SSH to the device, transfer 'sysupgrade' image and perform upgrade in forced mode, without preserving settings: 'sysupgrade -n -F ...'. Other notes: If you own early version of this device, the vendor firmware might refuse OpenWrt image because of missing custom header. In that case, ask vendor's customer support for stock firmware without custom header support/requirement. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit f1aaa267f0ea18ffe5840f3ce46a48be123d2f62)
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-031-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5)
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-021-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
* ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)Kim DoHyoung2023-06-251-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr> (cherry picked from commit 0bbd5699c81d6887c4d895e85b56d8c23b1211ec)
* ramips: Add support for Beeline SmartBox TURBO+Maximilian Weinmann2023-06-171-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router. Device specification -------------------- SoC Type: MediaTek MT7621AT (880 MHz, 2 cores) RAM (Nanya NT5CC64M16GP): 128 MiB Flash (Macronix MX30LF1G18AC): 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615N): a/n/ac, 4x4 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) USB ports: 1xUSB3.0 Buttons: 2 button (reset, wps) LEDs: Red, Green, Blue Zigbee (EFR32MG1B232GG): 3.0 Stock bootloader: U-Boot 1.1.3 Power: 12 VDC, 1.5 A Installation (fw 2.0.9) ----------------------- 1. Login to the web interface under SuperUser (root) credentials. Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the device written on the backplate stick. 2. Navigate to Setting -> WAN. Add: Name - WAN1 Connection Type - Static IP Address - 172.16.0.1 Netmask - 255.255.255.0 Save -> Apply. Set default: WAN1 3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add: Protocol - SSH Port - 22 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN Interface - WAN1 Save ->Apply Add: Protocol - HTTP Port - 80 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN interface - WAN1 Save -> Apply 4. Set up your PC ethernet: Connection Type - Static IP Address - 172.16.0.2 Netmask - 255.255.255.0 Gateway - 172.16.0.1 5. Connect PC using ethernet cable to the WAN port of the router 6. Connect to the router using SSH shell under SuperUser account 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface under admin account 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 171.16.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses (fw 2.0.9) ------------------------ +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:e8 | | WAN | label + 1 | *:e9 | | 2g | label + 4 | *:ec | | 5g | label + 5 | *:ed | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 Factory image format -------------------- +---+-------------------+-------------+--------------------+ | # | Offset | Size | Description | +---+-------------------+-------------+--------------------+ | 1 | 0x0 | 0x200 | Tag Header Factory | | 2 | 0x200 | 0x100 | Tag Header Kernel1 | | 3 | 0x300 | 0x100 | Tag Header Kernel2 | | 4 | 0x400 | SIZE_KERNEL | Kernel | | 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) | +---+-------------------+-------------+--------------------+ Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org> (cherry picked from commit 8fcfb21b16e7537b9a871a1f67cb218c6be93149)
* ramips: tplink,mr600v2: fix image generation for sysupgrade imageAndreas Böhler2023-06-081-0/+3
| | | | | | | | | | | The MR600v2 does not find its rootfs if it is neither directly after the kernel or aligned to an erase block boundary (64k). This aligns the rootfs to 0x10000 allowing the device to boot again. Based on investigation by forum user relghuar. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 46b51e9e992884c81f4838440cd2967e67db3a79)
* ramips: fix lzma-loader for ASIARF boardsDaniel Danzberger2023-06-071-0/+2
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> (cherry picked from commit 29a5cb7a8b105ca6534bba63edcec48ae935c078)
* ramips: add basic common recipe for nand flash devicesShiji Yang2023-05-181-207/+47
| | | | | | | | These same codes are repeated for many devices now, it's better to move them to shared definition. This commit also add the missing KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: set default BLOCKSIZE to 64k for nor flash devicesShiji Yang2023-05-181-6/+0
| | | | | | | | | In kernel 5.15, the default erase sector size of the nor flash has been switched from 4k to 64k. This may cause the configuration not be preserved across upgrades. To avoid this issue, change the default BLOCKSIZE to 64k. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: rename to D-Team Newifi D2 and Lenovo Newifi D1Arınç ÜNAL2023-05-181-4/+4
| | | | | | | Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1. Let's not make naming exceptions because of marketing whims. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for TOZED ZLT S12 PROArınç ÜNAL2023-05-181-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: remove device tree legacy compatibilityNick Hainke2023-05-121-4/+0
| | | | | | | We switched to 5.15 kernel, so we don't need to maintain 5.10 compatibility anymore. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: add support for Linksys RE7000Christoph Krapp2023-05-091-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com>
* ramips: add support for SNR-CPE-ME1Maximilian Weinmann2023-05-071-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 16 MiB (GD25Q128CSIG) - WLAN : 2.4 GHz (MediaTek MT7603EN) 5 GHz (MediaTek MT7610EN) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (in SoC) - USB : 3.0 x1 - UART : through-hole on PCB - [J4] 3.3V, RX, TX, GND (57600n8) - Power : 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME1 to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: mt7621: rename Asus RT-AC57U to v1Felix Baumann2023-05-061-2/+4
| | | | | | rename RT-AC57U to avoid confusion with unsupported revisions 2 and 3 Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-021-3/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: add factory image for TP-Link EC330-G5u v1Mikhail Zhilkin2023-04-291-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows to install OpenWrt without connecting a serial cable (UART). Installation using factory image -------------------------------- Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link firmware. 1. Login to the router web interface (http://192.168.0.1/ by default) and save running config to "conf.bin" file 2. Open configuration file in any TP-Link config editor (e.g. https://jahed.github.io/tp-link-config-editor/) 3. Find "DeviceInfo" section and insert a new string "<Description val="Modem Router`telnetd -p 1023 -l login`" />" according to the following example: <DeviceInfo> ... <Description val="Modem Router`telnetd -p 1023 -l login`" /> ... </DeviceInfo> 4. Save configuration file and upload changed configuration using stock firmware interface 5. Login using telnet to IP:192.168.0.1 (Username:admin, password:1234) 6. Run "cat /proc/mtd | grep mtd7" a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000', then install stock firmware using web interface to toggle booted firmware image from "os1" to "os0" b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000', then all is ok, go to the next step 7. Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100 in this example) 8. Login using telnet to 192.168.0.1 9. Download OpenWrt factory.bin image from the tftp server: cd /tmp tftp -g -r factory.bin 192.168.0.100 10. Write OpenWrt factory.bin image: dd if=/tmp/factory.bin of=/dev/mtdblock1 11. Power cycle the router Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for D-Link DAP-1620 B1Rani Hod2023-04-291-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | The DAP-1620 rev B is a wall-plug AC1300 repeater. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI NOR - MT7615DN 2x2 802.11n +2x2 802.11ac (DBDC) - Ethernet: 1 port 10/100/1000 - Status LEDs (1x red+green) - LED RSSI bargraph (2x green, 1x red+green) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tail -c+117 DAP1620B1_FW212B03.bin | \ openssl aes-256-cbc -d -md md5 -out decrypted.bin \ -k 905503a4e0c3cd3c1ce062246de427a68962347e - flash decrypted.bin via D-Link Web Recovery Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: mt7621: add support for ZyXEL WSM20Andreas Böhler2023-04-291-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device
* ramips: Cudy X6 fixes / improvementsFelix Baumann2023-04-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | - Correct WiFi MACs, they didn't match oem firmware - Move nvmem-cells to bdinfo partition and remove &bdinfo reference - Add OEM device model name R13 to SUPPORTED_DEVICES This allows sysupgrading from Cudy's OpenWrt fork without force - Label red_led and use it during failsafe mode and upgrades MAC addresses as verified by OEM firmware: use address source LAN b4:4b:d6:2d:c8:4a label WAN b4:4b:d6:2d:c8:4b label + 1 2g b4:4b:d6:2d:c8:4a label 5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [read wifi mac from flash offset] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix lzma-loader for buffalo_WSR_600DHPHaoan Li2023-04-231-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #11919 Signed-off-by: Haoan Li <lihaoan1001@163.com>
* ramips: Add support for CJ-Hello HYC-G920Muhammad AL-Qadhy2023-04-011-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
* ramips: add support for Mercusys MR70XDavid Bauer2023-03-241-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: Winbond W25Q128JV (SPI-NOR 16MB) - WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC) - UART: >TX RX GND 3v3 (115200 8N1, J1) Do not connect 3v3. TX is marked with an arrow. Installation ============ Flash factory image. This can be done using stock web ui. Revert to stock firmware ======================== Flash stock firmware via OEM Web UI Recovery mode. Web UI Recovery method ====================== 1. Unplug the router 2. Plug in and hold reset button 5~10 secs 3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0 4. Flash image with web browser to 192.168.1.1 Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7621: enable lzma-loader for AFOUNDRY EW1200Tony Butler2023-03-221-0/+1
| | | | | | | | | Fixes boot loader LZMA decompression issues (LZMA ERROR 1) As reported in issue #12208 Reported-by: Raúl M. <raul.m@sparkedhost.com> Tested-by: Raúl M. <raul.m@sparkedhost.com> Signed-off-by: Tony Butler <spudz76@gmail.com>
* uencrypt: add support for mbedtlsEneas U de Queiroz2023-03-171-2/+2
| | | | | | | | | | | | | | This commit includes some additional changes: - better handling of iv and keys in openssl/wolfssl variants - fix compiler warnings and whitespace - build all 3 variants as separate packages - adjust the new package name in targets' DEVICE_PACKAGES - remove PKG_FLAGS:=nonshared [Beeline SmartBox Flash - OK] Tested-by: Mikhail Zhilkin <csharper2005@gmail.com> [after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size] Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* ramips: add support for TP-Link Archer AX23 v1David Bauer2023-03-151-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR () WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Upload the factory image using the Web-UI. Web-Recovery ------------ The router supports a HTTP recovery mode by holding the reset-button when powering on. The interface is reachable at 192.168.0.1 and supports installation using the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for SNR-CPE-ME2-SFPAleksey Nasibulin2023-03-081-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
* ramips: add support for D-Link Dir-853 A1Hang Zhou2023-03-041-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7621AT * RAM: 256MB (NT5CC64M16GP-DI) * Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver) * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * Ethernet: 4x1000M LAN, 1x 1000M WAN * LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons: Reset,WPS, Wifi * Serial interface: on board but not populated, pinout (from the DC jack side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600, settings are 8 data bits, no parity bit, one stop bit, and no flow control. Stock flash layout: ``` GD25Q128C(c8 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "Config2" 0x000000060000-0x000000fb0000 : "Kernel" 0x000000fb0000-0x000001000000 : "Private" ``` The kernel partition will be replaced with the OpenWrt image, the other partitions are left untouched. "Config2" seems to be the config storage used by the stock firmware. "Private" is a 320kB empty JFFS2 partition that comes with the stock firmware. One can get a larger space for OpenWrt by merging it with "Kernel". OpenWrt flash layout: ``` 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "u-boot-env" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000060000 : "config2_stock" 0x000000060000-0x000000fb0000 : "firmware" 0x000000fb0000-0x000001000000 : "private_stock" ``` The OpenWrt image must have 96 bytes of padding in the header. MAC addresses on OEM firmware: | | location on the flash | notes | |------ |----------------------- |---------- | | lan (eth2) | factory + 0xe000 | on label | | wan (eth3) | factory + 0xe006 | | | 2.4g (rax0) | not on flash | lan + 1 | | 5g (ra0) | not on flash | lan + 2 | Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in the u-boot-env partition, but they are not used. OpenWrt calculates Wifi Mac addresses based on the LAN Mac. Flash and test instructions: Flash the encrypted image (available in the OpenWrt forum) through the stock D-Dink web interface. 1. Open the case, and solder the 4-pin header near the WAN port. 2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC. 3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with the settings mentioned above. 4. Setup a TFTP server on your PC that can serve `xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`. 5. Connect any LAN port to your PC and set a static IPv4 address to 192.168.0.101 (netmask 255.255.255.0). 6. Power on the device and keeps pressing 1 until you see the prompt. 7. Use default IP addresses and enter the file name accordingly, then hit enter. 8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1, you need to change your PC network adapter to use DHCP in order to access LUCI. 9. So far, the OpenWrt runs in RAM and the flash contents are not touched. You can try OpenWrt without having to overwrite the stock firmware, a reboot clears all changes. 10. Optionally, backup the stock firmware (the "firmware" partition) in Luci. 11. To permantly install OpenWrt to the device , click on "System -> Backup/Flash Firmware" in Luci and flash `xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin` Known problems: * WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network, you need to config it manually in LUCI. * If you see jffs2 related warnings/errors after updating from the stock web interface, you need to do a reset in LUCI. The error will be gone after a cold reboot. Signed-off-by: Hang Zhou <929513338qq@gmail.com>
* mt7621: move uboot-envtools to DEFAULT_PACKAGESBjørn Mork2023-03-011-177/+193
| | | | | | | | | Several devices depend on fw_printenv during sysupgrade. Make sure it always is present in all images, including initramfs images built by the buildbots. Fixes: 2449a632084b ("ramips: mt7621: Add support for ZyXEL NR7101") Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ramips: add alternative device name for Wiflyer WF3526-PShiji Yang2023-02-191-0/+2
| | | | | | | | | Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design. Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi not work due to allocate the wrong pcie port. Add alternative name to help users easily build or download the correct firmware. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Huasifei WS1208V2Arınç ÜNAL2023-02-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a Quectel RM520N-GL cellular modem which supports QMI and MBIM modes. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI Flash - MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN - Quectel RM520N-GL Cellular Modem - 2 WLAN & 4 Cellular Antennas - 5 Gigabit Ethernet Ports - 1 USB 2.0 port - 1 PCI-E Slot - 1 M.2 slot - 1 SIM card slot - 1 SD card slot Installation: - Install sysupgrade image via ROOter OS. TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: fix the name of ASUS AX54 because it has dupilcated twiceKarl Chan2023-02-181-5/+3
| | | | | | The name of ASUS AX54 has dupilcated in the DEVICE_ALT0_VENDOR/DEVICE_ALT0_MODEL Signed-off-by: Karl Chan <exkc@exkc.moe>
* ramips: add support for ASUS RT-AX54Karl Chan2023-02-121-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX54 (AX1800S/HP,AX54HP) - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 4 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x POWER (blue, configurable) 1x LAN (blue, configurable) 1x WAN (blue, configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Karl Chan <exkc@exkc.moe>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-041-22/+22
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for TP-Link Deco M4R v4Mark Ceeha2023-02-031-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the V4 hardware revision of the Deco M4R. V4 is a complete overhaul of the hardware compared to V1 and V2, and is much more similar to the Archer C6 V3 and C6U V1. Specifications: SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads) RAM: Kingston D1216ECMDXGJD (256 MB) Wireless 2.4 GHz: MediaTek MT7603EN Wireless 5 GHz: MediaTek MT7613BEN Flash: 16 MB SPI NOR Installation: Flash the *-factory.bin image in the U-Boot recovery webserver. You can trigger this webserver by holding the reset button until the LED flashes yellow, or by hooking up to serial pads on the board (clearly labeled GND, RX and TX) and pressing `x` early in boot. Once the factory image has been flashed, you can use the regular upgrade procedure with sysupgrade images for subsequent flashes. Signed-off-by: Mark Ceeha <hi@shiz.me> Tested-by: Mark Ceeha <hi@shiz.me>
* ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2Dmitry Sokolov2023-01-281-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
* ramips: use hex value in zyimage command for Keenetic KN-3010Maxim Anisimov2023-01-281-1/+1
| | | | | | | This is cosmetic change. The hex value is related to the device model and more human friendly. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: mt7621: Add Arcadyan WE420223-99 supportHarm Berntsen2023-01-151-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
* ramips: add support for D-Link DIR-1935 A1Keith Harrison2023-01-141-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1, DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt "factory" firmware installs without modificaitons via the D-Link Recovery GUI and has no known incompatibilities with the DIR-1935 A1. Changes to be committed: new file: target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts modified: target/linux/ramips/image/mt7621.mk modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds Specifications: * Board: Not known * SoC: MediaTek MT7621 Family * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615 Family (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green) Notes: * 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no SSID is visible in wifi scanning apps on other devices) with either official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based on the 22.03.2 branch. 80 MHz 5GHz works. Serial port: * Untested (potential user damage/error) * Expected to be identical to other DIR-8xx A1 models: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Keith Harrison <keithh@protonmail.com>
* ramips: Alternative name Asus RT-AX1800U for Asus RT-AX53UFelix Baumann2023-01-141-0/+2
| | | | | | | | The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U. Use the ALT0 buildroot tags to show both devices. Tested-by: Marian Sarcinschi <znevna@gmail.com> Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: add basic support for TP-Link EC330-G5u v1Mikhail Zhilkin2023-01-141-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known as TP-Link Archer C9ERT). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB, Nanya NT5CC64M16GP-DI Flash: 128 MiB NAND, ESMT F59L1G81MA-25T Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4 Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 Button: 4 (Led, WiFi On/Off, Reset, WPS) LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED Power: 12 VDC, 2 A Connector type: Barrel Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally, original TP-Link firmware contains Image U-Boot (1.1.3). Serial console (UART) --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | J2 | +--- Don't connect Installation ------------ 1. Rename OpenWrt initramfs image to test.bin and place it on tftp server with IP 192.168.0.5 2. Attach UART, switch on the router and interrupt the boot process by pressing 't' 3. Load and run OpenWrt initramfs image: tftpboot bootm 4. Once inside OpenWrt, switch to the first boot image: fw_setenv BootImage 0 5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv BootImage 1 reboot Recovery -------- 1. Press Reset button and power on the router 2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload the OEM firmware MAC addresses ------------- +---------+-------------------+-------------------+-------------+ | | MAC example 1 | MAC example 2 | Algorithm | +---------+-------------------+-------------------+-------------+ | label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label | | LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label | | WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] | | WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label | | WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 | +---------+-------------------+-------------------+-------------+ label MAC address was found in factory at 0x165 (text format xx:xx:xx:xx:xx:xx). Notes ----- [1] WAN MAC address: a. First octet of WAN MAC is differ than others and OUI is not related to TP-Link company. This probably should be fixed. b. Flipping bits in first octet and hex delta are different for the different MAC examples: +-----------------+----------------+----------------+ | | Example 1 | Example 2 | +-----------------+----------------+----------------+ | LAN | 68 = 0110 1000 | 50 = 0101 0000 | | MAC (1st octet) | ^ ^ ^ | | +-----------------+----------------+----------------+ | WAN | 72 = 0111 0010 | 54 = 0101 0100 | | MAC (1st octet) | ^ ^ ^ | ^ | +-----------------+----------------+----------------+ | HEX delta | 0xa | 0x4 | +-----------------+----------------+----------------+ | DEC delta | 4 | 4 | +-----------------+----------------+----------------+ c. DEC delta is a constant (4). This looks like a mistake in OEM firmware and probably should be fixed. Based on the above, I decided to keep correct OUI and make WAN MAC = label + 1. [2] Bootloaders The device contains 3 bootloaders: - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot located on NAND Flash to load next full-feature Uboot. - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This bootloader includes recovery webserver. Requires special uImages to continue the boot process: 0x00 (os0, os1) - firmware uImage 0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here) - Additionally, both slots of the original TP-Link firmware contains Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image magics and CRCs. We don't use this U-Boot with OpenWrt. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ELECOM WRC-2533GHBK2-TINAGAKI Hiroshi2023-01-141-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G) - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, RX, GND, TX from SoC side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-2533GHBK2-T normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing MAC addresses: LAN : BC:5C:4C:xx:xx:FD (Config, "ethaddr" (text)) WAN : BC:5C:4C:xx:xx:FC (Config, "wanaddr" (text), Label) 2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4 (hex)) 5 GHz : BC:5C:4C:xx:xx:FF (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for D-Link DAP-X1860 A1Sebastian Schaper2023-01-071-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | The DAP-X1860 is a wall-plug AX1800 repeater. Specifications: - MT7621, 256 MiB RAM, 128 MiB SPI NAND - MT7915 + MT7975 2x2 802.11ax (DBDC) - Ethernet: 1 port 10/100/1000 - LED RSSI bargraph (2x green, 1x red/orange), status and RSSI LEDs are incorrectly populated red/orange (should be red/green according to documentation) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tar -xvf DAP-X1860_RevA_Firmware_101b94.bin - openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \ -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ== - tar -xvf FWImage.st1 - flash kernel_DAP-X1860.bin via Recovery Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* mt76: add stand-alone MT7622 firmware packageShiji Yang2023-01-071-61/+61
| | | | | | | | | Add a separate firmware package to avoid installing the MT7615 firmware on all MT7622 target devices by default. Now we only add MT7615 firmware packages for devices that use MT7615E. This commit also removes the explicit dependency on kmod-mt7615e to refine the package dependency. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* mt76: add stand-alone MT7915 firmware packageShiji Yang2023-01-071-18/+18
| | | | | | | | | The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only MT7915 series chips need the MT7915 firmware. To save storage, extract them from the common code package and create a new package to provide the firmware. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: use default lzma dictionary size for better performanceShiji Yang2023-01-071-1/+0
| | | | | | | | | | | | limit dictionary size patch was introduced to solve the well known "LZMA ERROR 1 - must RESET board to recover" error. 09b6755946409d8fd8 "ramips: limit dictionary size for lzma compression" It seems that it has failed recently and we can use lzma loader to fix this error by adding "$(Device/uimage-lzma-loader)". So just remove it to use the default parameter -d24 for a higher compression ratio. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: combine USW-Flex dual firmware-partitionsDavid Bauer2023-01-071-1/+1
| | | | | | | | | | | | | | | In order to maximize the available space on USW-Flex boards using a dual-image partition layout, combine the two OS partitions into a single partition. This allows users to access more usable space for additional packages. Don't limit the usable image size to the size of a single OS partition. The initial installation has to be done with an older version of OpenWrt in case the generated image exceeds the space of a single kernel partition in the future. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Cudy M1800Leon M. Busch-George2023-01-061-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications SoC: MT7621 CPU: 880 MHz Flash: 32 MiB RAM: 256 MiB WLAN: MT7915 WiFi 6 (2.4/5 GHz) Ethernet: 2x Gbit ports MAC LAN b4:4b:d6:2e:c7:b0 (label) WAN b4:4b:d6:2e:c7:b1 WiFi 2.4 00:0c:43:26:46:08 WiFi 5 00:0c:43:26:59:97 Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
* ramips: add Unielec U7621-06 32M build targetIgnas Poklad2023-01-051-0/+12
| | | | | | | | | Add 32M build target Rest of the details as per commit 46ab81e405d2 ("ramips add support for UniElec U7621-06") Signed-off-by: Ignas Poklad <ignas2526@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-13 13:33:14 +0000