aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: add support for TP9343-based TP-Link TL-WR94x devicesAdrian Schmutzler2019-08-052-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for several TP-Link devices based on TP9343 ("a QCA9561 without PCIe and USB"): - TL-WR940N v3 - TL-WR940N v4 - TL-WR941ND v6 The devices are only different concerning LEDs and MAC address assignment. All TL-WR940 are with non-detachable antennas (N), all TL-WR941 devices are with detachable antennas (ND). Specification: - 750 MHz CPU - 32 MB of RAM - 4 MB of FLASH - 2.4 GHz WiFi - 4x 10/100 Mbps Ethernet Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to * (see below) 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. * TFTP image names: 940 v3: wr941ndv6_tp_recovery.bin 940 v4: wr940nv4_tp_recovery.bin 941 v6: wr941ndv6_tp_recovery.bin Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for D-Link DIR-842 C1Jackson Lim2019-08-054-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C1: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [fix whitespace issues] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WR841N/ND v12Adrian Schmutzler2019-08-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC ID, same TFTP image name...). Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin (it's really v11, not v12) 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR841N/ND v10Adrian Schmutzler2019-08-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor changes, it contains a newer revision of the QCA9533 SoC and the CPU clock is significantly higher. Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for ALFA Network AP121FRoger Pueyo Centelles2019-07-312-0/+4
| | | | | | | | | | | | | This commit ports support for the ALFA Network AP121F, a pocket-size router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the ath79 target (it was already supported in ar71xx; see commit 0c6165d2 for more details). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env partition writable] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: fix indent in 01_ledsAdrian Schmutzler2019-07-241-2/+2
| | | | | | | | | Change capitalization from spaces to tabs in order to match the style of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [fix capitalization in commit title, add short description] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-842 C2Jackson Lim2019-07-244-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C2: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: 2.0 Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [Reword reset-hog comment, fix formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Add support for TP-Link Archer C60 v2Adrian Schmutzler2019-07-183-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 ...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C60 v1Adrian Schmutzler2019-07-183-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 ...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510-v2/v3Andrew Cameron2019-07-182-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Trendnet TEW-823DRUPramod Pancha2019-07-183-1/+17
| | | | | | | | | | | | | | | | | | | | | Trendnet TEW-823DRU is a dual-band AC1750 router. The router is based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: 720 MHz CPU 256 MB of RAM 16 MB of FLASH 3T3R 2.4 GHz 3T3R 5 GHz 5x 10/100/1000 Mbps Ethernet Firmware can be flashed from the web interface. Tested on 3 routers with no issues. Signed-off-by: Pramod Pancha <pancha@vill.com> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link RE355 v1 and RE450 v1Christoph Krapp2019-07-174-0/+15
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: Qualcomm Atheros QCA9558 RAM: 64/128MiB Flash: 8MiB SPI-NOR Wifi: - 2.4GHz: 3T3R (QCA9558) - 5GHz: 3T3R (QCA9880) LAN: 1x 10/100/1000 Mbps UART: - TP1: Tx - TP2: Rx - TP3: Gnd - TP4: 3v3 Flash instructions: Flash factory image through stock firmware WEB UI. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: add support for Bluesocket BSAP1880 boardDaniel Gimpelevich2019-07-174-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-3/+3
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add seama header fixup for Qihoo C301Chuanhong Guo2019-07-161-0/+15
| | | | | | | | | This script is copied from ar71xx. Without a header fixup, u-boot checksum for kernel will fail after the first boot. Fixes: a9360452f0 ("ath79: add support for Qihoo C301") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add wmac migration for all ar93xx/qca95xx SoCsChuanhong Guo2019-07-161-5/+6
| | | | | | | Add migration for all ar71xx device path as well as previously incorrect ath79 path. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Qihoo C301Chuanhong Guo2019-07-165-0/+31
| | | | | | | | | | | | | | | | Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-142-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Fix whitespace errors in 11-ath10k-caldataAdrian Schmutzler2019-07-091-2/+2
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-032-4/+4
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Code style improvements in 10_fix_wifi_macAdrian Schmutzler2019-06-251-4/+4
| | | | | | This fixes one comparison and several useless echos. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-242-0/+4
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: Merge cases in 11-ath10k-caldataAdrian Schmutzler2019-06-151-5/+2
| | | | | | Cosmetical patch that just merges two cases. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-104-9/+19
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: migrate Archer C7 5GHz radio device pathsDavid Santamaría Rogado2019-06-101-6/+20
| | | | | | | | | | | | | | | | | | When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Some people subtitute the unsupported QCA9880v1 in the Archer v1 with supported QCA9880v2 radio. Since the stock radio doesn't work, so it's safe to apply the change also for the Archer v1 images as well. Also this patch renames the migration file and variables from wmac to wifi. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed comment, added return 0 (not that it matters since uci is clever, see 00-wmac-migration thread), reworded commit message]
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-103-8/+5
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Read MAC addresses from flash in 11-ath10k-caldataAdrian Schmutzler2019-06-101-14/+23
| | | | | | | | | | In commit c3a8518 eth0 and eth1 have been swapped for some devices, but 11-ath10k-caldata has not been updated. Instead of fixing this by swapping eth0/eth1, this patch will read addresses from flash (as done for several devices already) so adjustments due to eth order become obsolete. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-101-9/+3
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for 8devices Carambola2 development boardRytis Zigmantavičius2019-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Atheros AR9331 (400 MHz) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 1T1R 2.4 Wlan (AR9331) - 2x 10/100 Mbps Ethernet - 3x LEDs, 1x gpio button - 1x USB 2.0, 5V - UART over usb, 115200n8 Upgrading from ar71xx target: - Put image into board: scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \ root@192.168.1.1/tmp/ - Run sysupgrade sysupgrade /tmp/sysupgrade.bin Upgrading from u-boot: - Set up tftp server with sysupgrade.bin image - Go to u-boot (reboot and press ESC when prompted) - Set TFTP server IP setenv serverip 192.168.1.254 - Set device ip from same subnet setenv ipaddr 192.168.1.1 - Copy new firmware to board tftpboot 0x81000000 sysupgrade.bin - erase flash erase 0x9f050000 +${filesize} - flash firmware cp.b 0x81000000 0x9f050000 ${filesize} - Reset board reset Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com> [wrapped long line in commit description, whitespace and art address fix in DTS, keep default lan/wan setup, removed -n in sysupgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for ZBT-WD323Kristian Evensen2019-06-053-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT-WD323 is a dual-LTE router based on AR9344. The detailed specifications are: * AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN). * 128 MB RAM * 16MB of flash(SPI-NOR, 22MHz) * 1x 2.4GHz wifi (Atheros AR9340) * 3x 10/100Mbos Ethernet (AR8229) * 1x USB2.0 port * 2x miniPCIe-slots (USB2.0 only) * 2x SIM slots (standard size) * 4x LEDs (1 gpio controlled) * 1x reset button * 1x 10 pin terminal block (RS232, RS485, 4x GPIO) * 2x CP210x UART bridge controllers (used for RS232 and RS485) * 1x 2 pin 5mm industrial interface (input voltage 12V~36V) * 1x DC jack * 1x RTC (PCF8563) Tested: - Ethernet switch - Wifi - USB port - MiniPCIe-slots (+ SIM slots) - Sysupgrade - Reset button - RS232 Intallation and recovery: The board ships with OpenWRT, but sysupgrade does not work as a different firmware format than what is expected is generated. The easiest way to install (and recover) the router, is to use the web-interface provided by the bootloader (Breed). While the interface is in Chinese, it is easy to use. First, in order to access the interface, you need to hold down the reset button for around five seconds. Then, go to 192.168.1.1 in your browser. Click on the second item in the list on the left to access the recovery page. The second item on the next page is where you select the firmware. Select the menu item containing "Atheros SDK" and "16MB" in the dropdown close to the buttom, and click on the button at the bottom to start installation/recovery. Notes: * RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1 Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: fix default config for devices with eth0/eth1 swappedChuanhong Guo2019-06-052-70/+56
| | | | | | | | | | | | | | | | also fix the following problems in this commit: glinet,gl-ar150: This router uses an uncommon order of setting up gmacs in ar71xx. gmac0 is preferred to be wan port because of the additional link status info available. So this router will have eth0/eth1 swapped comparing to ar71xx. tplink,tl-wr710n-v1: same as gl-ar150 embeddedwireless,dorin: eth0 is used as switch port, which was incorrect. It's correct now, so keep this one untouched. tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order is incorrect. reorder archer-a7-v5 entry. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: rework LED configurations for tplink,archer-d50-v1Chuanhong Guo2019-06-051-3/+3
| | | | | | | | | | | | The original one has the following problem: 1. Port mask of lan led includes wan port. 2. By using netdev trigger with vlan port, the link led is always on. This commits fixes the above problems by correcting port mask for lan led and use swconfig trigger for wan leds. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add leds migrations for archer-c7-v2 and v4David Santamaría Rogado2019-05-311-0/+6
| | | | | | | | | | | | In ar71xx v2 has blue color defined because the same mach-*.c is also used for TL-WDR4900 model with blue leds. ath79 v2 dts defines them as green. For v4 the situation is the same as v5 so the conversion is identical only v4 instead v5. So now upgrading from ar71xx to ath79 should be also smoother for v2 and v4. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ath79: add support for WD My Net N750Ryan Mounce2019-05-273-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9344 RAM: 128MB Flash: 16MiB Winbond 25Q128BVFG SPI NOR 5GHz WiFi: AR9380 PCIe 3x3:3 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Gigabit ethernet via AR8327N switch (green + amber LEDs) 2x USB 2.0 via GL850G hub 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO Known issues: AR8327N LEDs only have default functionality, not presented in sysfs. This is a regression from ar71xx. UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX See https://openwrt.org/toh/wd/n750 for flashing detail. Procedures unchanged from ar71xx. Tested sysupgrade + factory flash from WD Emergency Recovery Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ath79: add leds migrations for archer-c7-v5Petr Štetiar2019-05-201-0/+3
| | | | | | | | | ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more generic `tplink` as the DTS is reused by more boards, so we need to perform migrations of the LED names during upgrade. Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link Archer D50 V1Davide Fioravanti2019-05-183-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
* ath79: add support for Aruba AP-105Chris Blake2019-05-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ath79: Add support for TP-Link TL-WR1043N v5Adrian Schmutzler2019-05-182-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9563 at 775 MHz - 64 MB RAM Zentel A3R12E40CBF-8E - 16 MB flash Winbond W25Q128FVSG - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. It also has different partitioning scheme. The software is more in line with the Archer series in that it uses a nested bootloader scheme. (This has been adapted from the OpenWrt Wiki page) <https://openwrt.org/toh/tp-link/tl-wr1043nd> Installation on HW rev.5: Factory firmware can be installed via the WEB interface. Alternatively, it is also possible to use a TFTP server for recovery purposes: - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin - Set static IP of your PC to *192.168.0.66* - Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. And finally, there's always u-boot access through the UART. For information visit the wiki. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworked commit message]
* ath79: add support for EnGenius ECB1750sven friedmann2019-05-184-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-132-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-092-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Correct MAC address for WAN interface of Archer A7/C7 v5Adrian Schmutzler2019-04-081-0/+5
| | | | | | | | | | | These devices share the network config with C7v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti airCube ISPChristian Mauderer2019-04-082-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-082-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-063-7/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ath79: engenius epg5000: add leds migration scriptTomasz Maciej Nowak2019-04-061-0/+16
| | | | | | | | | | | | | | | With transition from ar71xx to ath79 some of devices change their naming of LEDs. When upgrading from ar71xx target images this will require the user to adjust previously working configuration. This commit adds migration script which can be used to rename old names to new ones. With this previously working configuration will be automatically adjusted, wihtout user intervention. This commit adds migration case for EnGenius EPG5000, the wireless LEDs names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to epg5000:blue:wlan2g and epg5000:blue:wlan5g. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add support for TP-Link CPE210 v2Adrian Schmutzler2019-04-022-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This is based on the support patch for the identical CPE210 v3 by Mario Schroen <m.schroen@web.de>. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for TP-Link CPE210 v3Mario Schroen2019-04-022-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros QCA9533 (650MHz) * RAM: 64MB * Storage: 8 MB SPI NOR * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Thanks to robimarko for the work inside the ar71xx tree. Thanks to adrianschmutzler for deep discussion and fixes. Signed-off-by: Mario Schroen <m.schroen@web.de> [Split into DTS/DTSI, read-only config partition in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename, light subject touches] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for COMFAST CF-E5/E7Ding Tengfei2019-03-243-10/+25
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on Qualcomm/Atheros QCA9531. Short specification: 2x 10/100 Mbps Ethernet, with 24v PoE support 64 MB of RAM (DDR2) 16 MB of FLASH (SPI) 2T2R 2.4 GHz, 802.11b/g/n built-in 1x 3 dBi antennas output power (max): 80 mW (19 dBm) Qucetel EC20 LTE MODULE(1x external detachable antenna) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [commit subject fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 12:26:37 +0000