aboutsummaryrefslogtreecommitdiffstats
path: root/package/firmware/ipq-wifi/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for MikroTik SXTsq 5 acRoger Pueyo Centelles2021-05-031-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> (cherry picked from commit d1f1e5269ed992e6fc30d575b43b0913c9e58ca2) [Compile and Run Tested] Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-05-031-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit faea7becafc634dc882f0ad8f9388862ccd5bd0d) [Compile Tested] Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: add support for NEC Platforms Aterm WG2600HP3Yanase Yuki2020-12-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062. Specification ------------- - SoC: Qualcomm IPQ8062 - RAM: 512MiB - Flash memory: SPI-NOR 32MiB (Cypress S25FL256S) - Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch) - Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN) - LED: 6x green LED, 6x red LED - Input: 2x tactile switch, 1x SP3T slide switch - Serial console: 115200bps, through-hole J3 - [ ] [GND] [ ] [TX] [RX] ----> DC jack - Power: DC 12V 1.5A This device does not support VHT160 and VHT80+80. Custom BDFs are required to limit VHT capabilities. Flash instructions ------------------ 1. Setup TFTP server (IP address: 192.168.1.2) 2. Put initramfs image into TFTP server directory 3. Connect WG2600HP3 lan port and computer that runs TFTP server 4. Connect to the serial console 5. Interrupt booting by Esc key (password: chiron) 6. Execute the following commands # setenv bootcmd "nboot 0x44000000 1 0x860000" # saveenv # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.2 # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage 7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory 8. Erase firmware partition # mtd erase firmware 9. Run sysupgrade Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-221-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-221-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-221-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: improve support for Edgecore ECW5211Sungbo Eo2020-10-071-2/+0
| | | | | | | | | | | | | | | | | | | This adds several stylistic and functional improvements of the recently added Edgecore ECW5211, especially: * Drop the local BDFs as those are already in the upstream under different names * Add SPDX tag to DTS * Add label MAC address * Move LED trigger to DTS * Remove unnecessary status="okay" * Disable unused SS USB phy as the USB port only supports USB 2.0 * Make uboot-env partition writable * Remove qcom,poll_required_dynamic property as the driver does not use it * Tidy up the device recipe Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: Add support for Linksys MR8300 (Dallas)Hans Geiblinger2020-09-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Luma Home WRTQ-329ACNTomasz Maciej Nowak2020-09-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band wireless access point. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 2 MB SPI NOR 128 MB SPI NAND WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 2x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU Buttons: 1x GPIO controlled EEPROM: 16 Kbit, compatible with AT24C16 UART: row of 4 holes marked on PCB as J19, starting count from the side of J19 marking on PCB 1. GND, 2. RX, 3. TX, 4. 3.3V baud: 115200, parity: none, flow control: none The device supports OTA or USB flash drive updates, unfotunately they are signed. Until the signing key is known, the UART access is mandatory for installation. The difficult part is disassembling the casing, there are a lot of latches holding it together. Teardown Prepare three thin, but sturdy, prying tools. Place the device with back of it facing upwards. Start with the wall having a small notch. Insert first tool, until You'll feel resistance and keep it there. Repeat the procedure for neighbouring walls. With applying a pressure, one edge of the back cover should pop up. Now carefully slide one of the tools to free the rest of the latches. There's no need to solder pins to the UART holes, You can use hook clips, but wiring them outside the casing, will ease debuging and recovery if problems occur. Installation 1. Prepare TFTP server with OpenWrt initramfs image. 2. Connect to UART port (don't connect the voltage pin). 3. Connect to LAN port. 4. Power on the device, carefully observe the console output and when asked quickly enter the failsafe mode. 5. Invoke 'mount_root'. 6. After the overlayfs is mounted run: fw_setenv bootdelay 3 This will allow to access U-Boot shell. 7. Reboot the device and when prompted to stop autoboot, hit any key. 8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x84000000 <openwrt_initramfs_image_name> bootm 0x84000000 and wait till OpenWrt boots. 9. In OpenWrt command line run following commands: fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000" fw_setenv bootcmd "run openwrt" 10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: ubirmvol /dev/ubi0 -N ubi_rootfs sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name> 11. After flashing, the access point will reboot to OpenWrt, then it's ready for configuration. Reverting to OEM firmware 1. Execute installation guide steps: 1, 2, 3, 7, 8. 2. In OpenWrt command line run following commands: ubirmvol /dev/ubi0 -N rootfs_data ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N kernel ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs ubimkvol /dev/ubi0 -S 34 -N kernel1 ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1 ubimkvol /dev/ubi0 -S 264 -N rootfs_data fw_setenv bootcmd bootipq 3. Reboot. Known issues The LEDs ring doesn't have any dedicated driver or application to control it, the only available option atm is to manipulate it with 'i2cset' command. The default action after applying power to device is spinning blue light. This light will stay active at all time. To disable it install 'i2c-tools' with opkg and run: i2cset -y 2 0x48 3 1 0 0 i The light will stay off until next cold boot. Additional information After completing 5. step from installation guide, one can disable asking for root password on OEM firmware by running: sed -e 's/root:x:/root::/' -i /etc/passwd This is useful for investigating the OEM firmware. One can look at the communication between the stock firmware and the vendor's cloud servers or as a way of making a backup of both flash chips. The root password seems to be constant across all sold devices. This is output of 'led_ctl' from OEM firmware to illustrate possibilities of LEDs ring: Usage: led_ctl [status | upgrade | force_upgrade | version] led_ctl solid COLOR <brightness> led_ctl single COLOR INDEX <brightness 0 - 15> led_ctl spinning COLOR <period 1 - 16 (lower = faster)> led_ctl fill COLOR <period 1 - 16 (lower = faster)> ( default is 5 ) led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128> (default is 34) ( default is 34 ) led_ctl pulsing COLOR COLOR: red, green, blue, yellow, purple, cyan, white Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit, changed ubi volumes for easier integration, slightly reworded commit message, changed ubi volume layout to use standard names all around] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add Edgecore OAP-100 supportJohn Crispin2020-09-171-0/+2
| | | | | | | | | | | | | | | | flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: add Edgecore ECW5211 supportRobert Marko2020-09-171-0/+2
| | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: add Edgecore ECW5410 supportRobert Marko2020-09-171-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* firmware: ipq-wifi: enable use on IPQ806xRobert Marko2020-09-171-1/+1
| | | | | | | | | This enables the ipq-wifi package to be used on IPQ806x target. Its needed for boards using a different BDF than one shipped in the upstream board-2.bin. Currently needed for Edgecore ECW5410. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add support for Buffalo WTR-M2133HPYanase Yuki2020-07-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019. Specification ------------- - SoC: Qualcomm IPQ4019 - RAM: 512MiB - Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC) - Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch) - Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch) - Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN) - LED: 4x white LED, 4x orange LED, 1x blue LED - USB: 1x USB 3.0 port - Input: 2x tactile switch, 2x slide switch (2x SP3T) - Serial console: 115200bps, pinheader JP5 on PCB - Power: DC 12V 2A Flash instruction ----------------- 1. Set up a TFTP server (IP address: 192.168.11.10) 2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage" and put it into the TFTP server directory. 3. Connect the TFTP server and WTR-M2133HP. 4. Hold down the AOSS button, then power on the router. 5. After booting OpenWrt initramfs image, connect to the router by SSH. 6. Transfer "squashfs-nand-factory.ubi" to the router. 7. Execute the following commands. # ubidetach -p /dev/mtd15 # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi # fw_setenv bootcmd bootipq 8. Perform reboot. Recover to stock firmware ------------------------- 1. Execute the following command. # fw_setenv bootcmd bootbf 2. Reboot and wait several minutes. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add support for GL.iNet GL-S1300Dongming Han2020-07-081-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq40xx: add support for EnGenius EMR3500Yen-Ting-Shen2020-06-131-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Cell C RTL30VWPawel Dembicki2020-04-101-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated QMI mPCIE modem. This is stripped version of ASKEY RTL0030VW. Hardware: Specification: -CPU: IPQ4019 -RAM: 256MB -Flash: NAND 128MB + NOR 16MB -WiFi: Integrated bgn/ac -LTE: mPCIe card (Modem chipset MDM9230) -LAN: 2 Gigabit Ports -USB: 2x USB2.0 -Serial console: RJ-45 115200 8n1 -Unsupported VoIP Known issues: None so far. Instruction install: There are two methods: Factory web-gui and serial + tftp. Web-gui: 1. Apply factory image via stock web-gui. Serial + initramfs: 1. Rename OpenWrt initramfs image to "image" 2. Connect serial console (115200,8n1) 3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4. 4. U-Boot commands: sf probe && sf read 0x80000000 0x180000 0x10000 setenv serverip 192.168.1.4 set fdt_high 0x85000000 tftpboot 0x84000000 image bootm 0x84000000 5. Install sysupgrade image via "sysupgrade -n" Back to stock: All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0, do firstboot and factory reset with OFW: 1. read mtd8: dd if=/dev/mtd8 of=/tmp/mtd8 2. go to tmp: cd /tmp/ 3. write first part of partition: dd if=mtd8 of=mtd8.new bs=1 count=76 4. check which layout uses bootloader: cat /proc/mtd 5a. If first are kernel_1 and rootfs_1 write 0: echo -n -e '\x00' >> mtd8.new 5b. If first are kernel and rootfs write 1: echo -n -e '\x01' >> mtd8.new 6. fill with rest of data: dd if=mtd8 bs=1 skip=77 >> mtd8.new 7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with: hexdump mtd8.new 8. write new mtd8 to flash: mtd write mtd8.new /dev/mtd8 9. do firstboot 10.reboot 11. Do back to factory defaults in OFW GUI. Based on work: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: add support for MobiPromo CM520-79FDENG Qingfang2020-04-101-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019 Specification: SoC/Wireless: QCA IPQ4019 RAM: 512MiB Flash: 128MiB SLC NAND Ethernet PHY: QCA8075 Ethernet ports: 1x WAN, 2x LAN LEDs: 7 LEDs 2 (USB, CAN) are GPIO other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register Button: Reset Flash instruction: Disassemble the router, connect UART pins like this: GND TX RX [x x . . x .] [. . . . . .] (QCA8075 and IPQ4019 below) Baud-rate: 115200 Set up TFTP server: IP 192.168.1.188/24 Power on the router and interrupt the booting with UART console env backup (in case you want to go back to stock and need it there): printenv (Copy the output to somewhere save) Set bootenv: setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs' setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1' setenv cm520_boot 'run set_ubi; run bootkernel' setenv bootcmd 'run cm520_boot' setenv bootargs saveenv Boot initramfs from TFTP: tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb bootm After initramfs image is booted, backup rootfs partition in case of reverting to stock image cat /dev/mtd12 > /tmp/mtd12.bin Then fetch it via SCP Upload nand-factory.ubi to /tmp via SCP, then run mtd erase rootfs mtd write /tmp/*nand-factory.ubi rootfs reboot To revert to stock image, restore default bootenv in uboot UART console setenv bootcmd 'bootipq' printenv use the saved dump you did back when you installed OpenWrt to verify that there are no other differences from back in the day. saveenv upload the backed up mtd12.bin and run tftpboot mtd12.bin nand erase 0xb80000 0x7480000 nand write 0x84000000 0xb80000 0x7480000 The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead In case of this, set it back to rootfs: cd /tmp cat /dev/mtd7 > mtd7.bin echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4 for i in 28 48 68 108; do dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i done mtd write mtd7.bin BOOTCONFIG mtd write mtd7.bin BOOTCONFIG1 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [renamed volume to ubi to support autoboot, as per David Lam's test in PR#2432] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for 8devices Habanero DVKRobert Marko2020-03-091-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the 8devices Habanero development board. Specs are: CPU: QCA IPQ4019 RAM: DDR3L 512MB Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without) WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2 WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2 Ethernet: 5x Gbit LAN (QCA 8075) USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019) MicroSD slot (Uses SD controller built into IPQ4019) SDIO3.0/EMMC slot (Uses the same SD controller) Mini PCI-E Gen 2.0 slot (Built into IPQ4019) 5x LEDs (4 GPIO controllable) 2x Pushbutton (1 is connected to GPIO, other to SoC reset) LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support) 1x UART 115200 rate on J18 2x breakout development headers 12V DC Jack for power DIP switch for bootstrap configuration Installation instructions: Since boards ship with vendors fork of OpenWrt sysupgrade can be used. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add support for EnGenius EAP2200Steven Lin2020-02-281-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB FLASH: NOR 4 MiB + NAND 128 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2 WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2 INPUT: WPS Button LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. c. Set a static ip 192.168.99.8 for Ethernet that connects to board. d. The PC must have a TFTP server launched and listening on the interface to which the board is connected. e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm Signed-off-by: Steven Lin <steven.lin@senao.com> [copied 4.19 dts to 5.4] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: drop deprecated .bin supportChristian Lamparter2020-01-261-3/+1
| | | | | | | | | | This patch converts the Qxwlan E2600AC image away from the deprecated .bin file and to the new .qca4019 method. As a result, we no longer need to carry around the legacy support for handling .bin files. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for EnGenius EMD1Yen-Ting-Shen2020-01-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (1 port) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMD1. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [removed BOARD_NAME] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Add support for D-Link DAP-2610Fredrik Olofsson2020-01-261-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications ============== - SOC: IPQ4018 - RAM: DDR3 256MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11 - 5GHz: IPQ4018, 2x2, front end SKY85717-21 - Ethernet: 1x 10/100/1000Mbps, POE 802.3af - PHY: QCA8072 - UART: GND, blocked, 3.3V, RX, TX / 115200 8N1 - LED: 1x red / green - Button: 1x reset / factory default - U-Boot bootloader with tftp and "emergency web server" accessible using serial port. Installation ============ Flash factory image from D-Link web UI. Constraints in the D-Link web UI makes the factory image unnecessarily large. Flash again using sysupgrade from inside OpenWrt to reclaim some flash space. Return to stock D-Link firmware =============================== Partition layout is preserved, and it is possible to return to the stock firmware simply by downloading it from D-Link and writing it to the firmware partition. # mtd -r write dap2610-firmware.bin firmware Quirks ====== To be flashable from the D-Link http server, the firmware must be larger then 6MB, and the size in the firmware header must match the actual file size. Also, the boot loader verifies the checksum of the firmware before each boot, thus the jffs2 must be after the checksum covered part. This is solved in the factory image by having the rootfs at the very end of the image (without pad-rootfs). The sysupgrade image which does not have to be flashable from the D-Link web UI may be smaller, and the checksum in the firmware header only covers the kernel part of the image. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> [added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux, added emd1's gmac0 config,fix dtc warnings] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for EZVIZ CS-W3-WD1200G EUPTom Brouwer2020-01-121-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SOC: Qualcomm IPQ4018 RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MB Macronix MX25L12805D ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN) WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz) BUTTON: Shared WPS/Reset button LED: RGB Status/Power LED SERIAL: Header J8 (UART, Left side of board). Numbered from top to bottom: (1) GND, (2) TX, (3) RX, (4) VCC (White triangle next to it). 3.3v, 115200, 8N1 Tested/Working: * Ethernet * WiFi (2.4 and 5GHz) * Status LED * Reset Button (See note below) Implementation notes: * The shared WPS/Reset button is implemented as a Reset button * I could not find a original firmware image to reverse engineer, meaning currently it's not possible to flash OpenWrt through the Web GUI. Installation (Through Serial console & TFTP): 1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to one of the LAN ports 2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on your pc, to serve the image 2. Connect to the router through serial (See connection properties above) 3. Hit a key during startup, to pause startup 4. type `setenv serverip 192.168.1.12`, to set the tftp server address 5. type `tftpboot`, to load the image from the laptop through tftp 6. type `bootm` to run the loaded image from memory 6. (If you want to return to stock firmware later, create an full MTD backup, e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup) 7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.: `scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin` 8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin` Revert to stock: To revert to stock, you need the MTD backup from step 6 above: 1. Unpack the MTD backup archive 2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup) 3. On the router, do `mtd write mtd8_firmware.backup firmware` Signed-off-by: Tom Brouwer <tombrouwer@outlook.com> [removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: add BDF for Aruba AP-303David Bauer2019-12-201-0/+2
| | | | | | The BDF originates from the vendor-firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: add AVM FRITZ!Repeater 1200 bdfDavid Bauer2019-10-231-0/+2
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: drop upstreamed custom board-2.binChristian Lamparter2019-08-181-14/+0
| | | | | | | | | | | | | | | | | | | | | | The BDFs for the: ALFA Network AP120C-AC ASUS Lyra AVM FRITZ!Box 7530 AVM FRITZ!Repeater 3000 EnGenius EAP1300 EnGenius ENS620EXT Netgear Orbi Pro SRK60 boards were upstreamed to the ath10k-firmware repository and linux-firmware.git. Furthermore the BDFs for the: OpenMesh A42 specific BDFs OpenMesh A62 specific BDFs Linksys EA6350v3 have been updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Add support for Linksys EA8300 (Dallas)Jeff Kletsky2019-05-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* firmware/ipq-wifi: Extend for multi-chip boardsJeff Kletsky2019-05-181-19/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ipq40xx: add support for EnGenius ENS620EXTSteve Glennon2019-03-211-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for AVM FRITZ!Repeater 3000David Bauer2019-03-131-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for FritzBox 7530David Bauer2019-02-281-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Qxwlan E2600AC C1 and C2张鹏2019-02-281-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: add board-2.bin for ALFA Network AP120C-ACPiotr Dymacz2019-02-261-1/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware: ipq-wifi: mark packages as nonsharedChristian Lamparter2019-02-201-0/+1
| | | | | | | | | | | The board-files are specific to the target and device. Hence they need to be set as nonshared. Otherwise they do not show up on the package repository. This causes problems for imagebuilder, if it needs to build a image for a specific device that hasn't had the time to have get its boardfile upstream. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS LyraMarius Genheimer2019-02-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: add support for Linksys EA6350v3Oever González2019-01-261-1/+2
| | | | | | | | | | | | This commit adds support for the Linksys EA6350v3 device in the ipq-wifi target. Without this patch, the Linksys EA6350v3 won't be hable to have fully functional wireless interfaces. This is not permanent: the board data has already been sent to ath10k _at_ lists _dot_ infradead _dot_ org Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com>
* ipq40xx: add support for EnGenius EAP1300Steven Lin2018-12-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
* ipq-wifi: drop custom board-2.binsChristian Lamparter2018-11-011-3/+1
| | | | | | | | | | | | | The BDFs for all boards were upstreamed to the ath10k-firmware repository and linux-firmware.git. We switched to the upstream board-2.bin, hence the files can be removed here. Keep the ipq-wifi package in case new boards are added. It might take some time till board-2.bins send upstream are merged. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: add a note / reminder about upstreaming new board filesChristian Lamparter2018-07-301-0/+3
| | | | | | | | |Please send a mail with your device-specific board files upstream. |You can find instructions and examples on the linux-wireless wiki: |<https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for the ZyXEL NBG6617Christian Lamparter2018-06-261-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ZyXEL NBG6617 Hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz NOR: 32 MiB Macronix MX25L25635F ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS Serial: WARNING: The serial port needs a TTL/RS-232 3.3v level converter! The Serial setting is 115200-8-N-1. The 1x4 .1" header comes pre-soldered. Pinout: 1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX first install / debricking / restore stock: 0. Have a PC running a tftp-server @ 192.168.1.99/24 1. connect the PC to any LAN-Ports 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file into the tftp-server root directory and rename it to just "ras.bin". 3. power-cycle the router and hold down the the WPS button (for 30sek) 4. Wait (for a long time - the serial console provides some progress reports. The u-boot says it best: "Please be patient". 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs flashes fast at the same time. You have to reboot the device and it should then come right up. Installation via Web-UI: 0. Connect a PC to the powered-on router. It will assign your PC a IP-address via DHCP 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234) 2. Go to the "Expert Mode" 3. Under "Maintenance", select "Firmware-Upgrade" 4. Upload the OpenWRT factory image 5. Wait for the Device to finish. It will reboot into OpenWRT without any additional actions needed. To open the ZyXEL NBG6617: 0. remove the four rubber feet glued on the backside 1. remove the four philips screws and pry open the top cover (by applying force between the plastic top housing from the backside/lan-port side) Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6617> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6617> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6617> ATSE NBG6617 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6617> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6617> ATGU |NBG6617# Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-181-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ipq-wifi: drop custom board-2.binsSven Eckelmann2018-04-231-7/+3
| | | | | | | | | | | | | The BDFs for all boards were upstreamed to the ath10k-firmware repository and are now part of ath10k-firmware 2018-04-19. We switched to the upstream board-2.bin, hence the files can be removed here. Keep the ipq-wifi package in case new boards are added. It might take some time till board-2.bins send upstream are merged. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: unbundle firmware and board fileMathias Kresin2018-04-131-1/+1
| | | | | | | | | | | Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for Netgear EX6100v2/EX6150v2David Bauer2018-04-131-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: Add 8devices JalapenoRobert Marko2018-04-131-1/+2
| | | | | | | Add custom board-2.bin for 8devices Jalapeno. Upstreaming is in progress. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add Cisco Meraki MR33 SupportChris Blake2018-03-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13Christian Lamparter2018-03-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add targetJohn Crispin2018-03-141-1/+1
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-26 08:52:36 +0000