aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* uboot-envtools: oxnas: sync with current oxnas/ox820 DTSDaniel Golle2019-03-011-5/+4
| | | | | | | | | Use tested values on shuttle,kd20 and assumed values for mitrastar,stg-212 and cloudengines,pogoplug*. akitio users have yet to report back stock flash layout to support vendor bootloader environment there as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: add support for FritzBox 7530David Bauer2019-02-281-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* uboot-fritz4040: bump version to 2019-02-08David Bauer2019-02-281-5/+6
| | | | | | | Adds support for the AVM FRITZ!Box 7530. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
* sunxi: add support for Orange Pi OneAleksander Jan Bajkowski2019-02-261-0/+7
| | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 512MB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard header: SPI, I2C, GPIO, UART USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* uboot-envtools: add support for ALFA Network AP120C-ACPiotr Dymacz2019-02-261-3/+4
| | | | | | While at it, fix alphabetical order. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-kirkwood: update to 2019.01Paul Wassi2019-02-1710-80/+83
| | | | | | Update U-Boot to current 2019.01 release for kirkwood platform Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* sunxi: add support for Sinovoip Banana Pi M2 PlusPawel Dembicki2019-02-171-0/+7
| | | | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E) Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG Untested: Audio, Video Not working: Bluetooth Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* build: remove leftovers from previous x86 commitsTomasz Maciej Nowak2019-02-171-2/+2
| | | | | | | | | | | | | | | | | VBoxManage is not used and the image is created with proper permisions: 0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host dependencies on qemu-utils and VirtualBox Unreachable config symbols: 9e0759e x86: merge all geode based subtargets into one No need to define those symbols since x86_64 is subtarget of x86: 196fb76 x86: make x86_64 a subtarget instead of a standalone target Unreachable config symbols, so remove GRUB_ROOT: 371b382 x86: remove the xen_domu subtarget Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* uboot-omap: add 'rootwait' to the kernel cmdlineAndre Heider2019-01-311-1/+1
| | | | | | Some SD cards take a while to get detected, fix booting of those. Signed-off-by: Andre Heider <a.heider@gmail.com>
* uboot-imx6: Bump to 2019.01Petr Štetiar2019-01-263-10/+10
| | | | | | | | | | | | Build tested: apalis, mx6sabresd, nitrogen6dl, nitrogen6dl2g, nitrogen6q, nitrogen6q2g, nitrogen6s, nitrogen6s1g, wandboard Run tested: apalis (pending PR #1595) Cc: Felix Fietkau <nbd@nbd.name> Cc: Vladimir Vid <vladimir.vid@sartura.hr> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-mxs: bump to v2019.01Michael Heimpold2019-01-262-9/+35
| | | | | | Also update the U-Boot BSP patch for I2SE Duckbill devices. Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* uboot-envtools: add support for Linksys EA6350v3Oever González2019-01-261-0/+3
| | | | | | | | | | | | | This commit adds support for the Linksys EA6350v3 device in the ipq40xx target. This is needed for uboot-envtools to access the environment. Without this patch, the Linksys EA6350v3 will not be able to access the uboot environment. As a side effect, the feature auto_recovery will make the device unstable by switching between the latest and the current firmware. Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com>
* uboot-fritz4040: update package to 2019-01-25Christian Lamparter2019-01-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | David Bauer reported a u-boot crash (data abort) at a odd place (byteswap) when he ran ping/tftp on his 7530. |(FRITZ7530) # ping 192.168.1.70 |eth0 PHY0 up Speed :1000 Full duplex |eth0 PHY1 Down Speed :10 Half duplex |eth0 PHY2 Down Speed :10 Half duplex |eth0 PHY3 Down Speed :10 Half duplex |eth0 PHY4 Down Speed :10 Half duplex |Using eth0 device |data abort |pc : [<84234774>] lr : [<842351a4>] |sp : 8412fdb0 ip : 0000009b fp : 00000000 |r10: 00000000 r9 : 00000001 r8 : 8412ff68 |r7 : 00000000 r6 : 0000002a r5 : 84244e90 r4 : 8425e28e |r3 : 84244e90 r2 : 14000045 r1 : 8412fdb0 r0 : 8425e28e |Flags: nZCv IRQs off FIQs off Mode SVC_32 |Resetting CPU ... | |resetting ... This issue is caused by switch from gcc 5.5 to 7.1+ as explained in the upstream patch: |From a768e513b07b5999a8e7d7740ac8d9da04ee7e51 Mon Sep 17 00:00:00 2001 |From: Denis Pynkin <denis.pynkin@collabora.com> |Date: Fri, 21 Jul 2017 19:28:42 +0300 |Subject: [PATCH] net: Use packed structures for networking | |PXE boot is broken with GCC 7.1 due option '-fstore-merging' enabled |by default for '-O2': | |BOOTP broadcast 1 |data abort |pc : [<8ff8bb30>] lr : [<00004f1f>] |reloc pc : [<17832b30>] lr : [<878abf1f>] |sp : 8f558bc0 ip : 00000000 fp : 8ffef5a4 |r10: 8ffed248 r9 : 8f558ee0 r8 : 8ffef594 |r7 : 0000000e r6 : 8ffed700 r5 : 00000000 r4 : 8ffed74e |r3 : 00060101 r2 : 8ffed230 r1 : 8ffed706 r0 : 00000ddd |Flags: nzcv IRQs off FIQs off Mode S | |Core reason is usage of structures for network headers without packed |attribute. Reported-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add support for OCEDO PandaDavid Bauer2019-01-261-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: FSL P1020 (2x 800MHz E500 PPC) RAM: 1GB DDR3 FLASH: 256MiB NAND WiFi: 2x Atheros AR9382 2x2:2 abgn ETH: 2x BCM54616S - 1x BCM53128 8-port switch LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS) BTN: 1x RESET Installation ------------ 1. Download initrams kernel image, dtb binary and sysupgrade image. 2. Place initramfs kernel into tftp root directory. Rename to "panda-uimage-factory". 3. Place dtb binary into tftp root directory. Rename to "panda.fdt". 4. Start tftp server on 192.168.100.8/24. 5. Power up the device with the reset button pressed. It will download the initrams and dtb via tftp and boot into OpenWRT in RAM. 6. SSH into the device and remove the factory partitions. > ubirmvol /dev/ubi0 --name=kernel1 > ubirmvol /dev/ubi0 --name=rootfs1 > ubirmvol /dev/ubi0 --name=devicetree1 You will have around 60 MiB of free space with that. You can also delete "kernel2", "devicetree2", "rootfs2" and "storage" respectively in case you do not want to go back to the vendor firmware. 7. Modify the U-Boot bootcmd to allow for booting OpenWRT > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel && bootm 0x1000000" > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200 ubi.mtd=3,2048" > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt" 8. Transfer the sysupgrade image via scp into the /tmp directory. 9. Upgrade the device > sysupgrade -n /tmp/<imagename> Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-ar71xx: fix musl host buildAndy Walsh2019-01-221-0/+13
| | | | | | | | | | | | | | On musl based distributions, u-boot 2010.03 fails to build with: u-boot-2010.03/include/u-boot/crc.h:29:50: error: unknown type name 'uint' uint32_t crc32 (uint32_t, const unsigned char *, uint); The issue was fixed in the newer u-boot-2018.03 version, this commit backports the change to the older version used by ar71xx/ath79. Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com> [add commit message from PR description] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uboot-sunxi: Orange Pi Zero Plus: Fix SdCard detectionHauke Mehrtens2019-01-131-0/+28
| | | | | | | | | The Detection pin is at PF6 and not at PH13 like defined before. I checked the schematics and now I am am not seeing this error message any more: Loading Environment from FAT... Card did not respond to voltage select! Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-sunxi: disable AXP209 on Olimex A13 OlinuxinoZoltan HERPAI2019-01-131-0/+19
| | | | | | | | | | | | | | Disable the PMIC on Olimex A13 Olinuxino, as the SPL cannot set the core voltage correctly, which causes the board to freeze later at kernel if CPU throttling is enabled (see below). This will almost certainly kill the VGA output (which requires LDO3 to be set), but this is still a better option than to disable CPU throttling for all Cortex-A8 based devices. [ 2.485632] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz [ 2.525698] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 432000 KHz Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: update Theobroma A31 Pangolin supportZoltan HERPAI2019-01-131-3/+1
| | | | | | Drop removed pinctrl definitions from the i2c3 pin layout. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* arm-trusted-firmware-sunxi: Replace with official ARM versionHauke Mehrtens2019-01-131-6/+6
| | | | | | | | | Instead of using a fork of the ARM trusted firmware specifically for the Allwinner SoCs, use the official version from ARM now, this version supports the Allwinner SoCs now and the older ATF repository is deprecated. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-sunxi: Update to version 2018.11Hauke Mehrtens2019-01-1312-481/+17
| | | | | | | This updates the uboot for the sunxi target to version 2018.11 The removed patches are applied upstream and not needed any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGEDavid Bauer2019-01-061-1/+7
| | | | | | | | | | | | Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-envtools: Add domywifi dw33d supportshanpo2019-01-021-0/+1
| | | | Signed-off-by: shanpo <jwdsccd@gmail.com>
* uboot-envtools: ipq40xx: Configuration for GL.iNet GL-B1300Ibrahim Tachijian2019-01-021-0/+1
| | | | | | This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board. Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-311-1/+2
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* layerscape: add LS1021AIOT board supportBiwen Li2018-12-182-1/+19
| | | | | | | | | | | | | | | | | | | | | | | The LS1021A-IoT gateway reference design based on the QorIQ LS1021A processor is a purpose-built, small footprint hardware platform with a wide array of high-speed connectivity and low-speed serial interfaces to support secure delivery of IoT services for home, business or other commercial location. - Combines standards-based, open source software with a feature-rich IoT gateway design to establish a common, open framework for secured IoT service delivery and management. - Provides a wide assortment of high-speed and serial-based connectivity in a compact, highly secure design. - High efficiency through the use of the Arm-based QorIQ LS1021A embedded processor. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Biwen Li <biwen.li@nxp.com>
* uboot-envtools: fix configuration for I2SE DuckbillsMichael Heimpold2018-12-182-2/+2
| | | | | | | | After changing board names to DT compat string, we also need to adjust the script which generates uboot-env configuration files. Fixes: e880a30549b ("mxs: use generic sysinfo board detection") Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* uboot-envtools: ath79: add support for the Buffalo BHR-4GRV2Stefan Lippers-Hollmann2018-12-181-0/+1
| | | | | | | | | | | According to https://github.com/openwrt/openwrt/pull/1527, support for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from an initramfs image, make this easier by supporting uboot-envtools support out of the box. Build tested, but not runtime tested. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* uboot-envtools: ath79: add support for the Buffalo WZR-HP-AG300HStefan Lippers-Hollmann2018-12-181-0/+3
| | | | | | | | | Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to ath79 as well. Build- and runtime tested on the Buffalo WZR-HP-AG300H. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3Mathias Kresin2018-12-121-1/+0
| | | | | | | | | | | | Beside one exception, no one took care of these two remaining boards still using the legacy image build code during the last two years. Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken. The Sitecom WL-341 v3 image build code looks pretty hackish and broken. It's questionable if the legacy image works as all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-fritz4040: update package to 2018-12-09Christian Lamparter2018-12-114-353/+5
| | | | | | | | | | | | | | | | | This patch updates the uboot-fritz4040 package to the latest version. The portability and private-libgcc patches, as well as the upload-to-f4040.sh script have been added to the upstream repository. Furthermore, the upload-to-f4040 has been updated to take the first parameter as the file it is supposed to flash, otherwise it defaults to the previous "uboot-fritz4040.bin". Furthermore the error messages have been improved and ftp will now dump some "progress information" to the user's console. Also included is support for gcc 8+ and a fix for the obnoxous error that currently breaks the builders: | fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Netgear WNDAP620 and WNDAP660Christian Lamparter2018-11-261-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WNDAP620 and WNDAP660, they are similar devices, but due to the LAN LED configuration, the switch setup and WIFI configuration each gets a different device target. Hardware Highlights WNDAP620: CPU: AMCC PowerPC APM82181 at 1000 MHz DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF CPU: AMCC PowerPC APM82181 at 1000 MHz FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE) Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes Hardware Highlights WNDAP660: CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks DRAM: 256 MB, 2 x 128 MiB DDR2 FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE) Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes Flashing requirements: - needs a tftp server at 192.168.1.10/serverip. - special 8P8C(aka RJ45)<->D-SUB9 Console Cable ("Cisco Console Cable"). Note: Both WNDAP6x0 have a MAX3232 transceivers, hence no need for any separate CMOS/TTL level shifters. External Antenna: The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations: = Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description ===== 1. | 1 / High | 0 / Low | Use the internal antennae (default) 2. | 0 / Low | 1 / High | Use the external antennae The external antennaes are only meant for the 2.4 GHz band. One-way Flashing instructions via u-boot: 0. connect the serial cable to the RJ45 Console Port Note: This requires a poper RS232 and not a TTL/USB adaptor. 1. power up the AP and interrupt the u-boot process at 'Hit any key to stop autoboot' 2. setup serverip and ipaddr env settings Enter the following commands into the u-boot shell # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.10 3. download the factory.img image to the AP Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img 4. verfiy image integrity Enter the following commands into the u-boot shell # crc32 $fileaddr $filesize If the calculated crc32 checksum does not match, go back to step 3. 5. flash the image Enter the following commands into the u-boot shell # nand erase 0x110000 0x1bd0000 # nand write ${kernel_addr_r} 0x110000 ${filesize} 6. setup uboot environment Enter the following commands into the u-boot shell # setenv bootargs # setenv fileaddr # setenv filesize # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0' # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}' # setenv bootcmd 'run owrt_boot' # saveenv 7. boot # run bootcmd Booting initramfs instructions via u-boot: Follow steps 0 - 2 from above. 3. boot initramfs Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin # run addtty # bootm ${kernel_addr_r} Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MX60(W): enable u-boot environmentChristian Lamparter2018-11-261-0/+3
| | | | | | | | | This patch adds u-boot environment access to the MX60(W) target. "The environment size is one NAND block (128KiB on Buckminster). We allocate four NAND blocks to deal with bad blocks which may exist in the saved environment" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MR24: add to uboot-envtoolsChristian Lamparter2018-11-261-0/+4
| | | | | | | | This patch adds the complicated u-boot environment access settings for to the MR24 target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add uboot-envtools supportChristian Lamparter2018-11-261-0/+18
| | | | | | | | | All apm821xx devices use u-boot and most of them have an accessible u-boot environment. This patch adds the necessary template file, but does not add the uboot-envtools package to any of the targets. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* uboot-mxs: bump to v2018.09Michael Heimpold2018-11-014-130/+72
| | | | | | | Also update the U-Boot BSP patch for I2SE Duckbill devices and remove upstreamed patch for LibreSSL support. Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* grub2: fix regression caused by binutils-2.31.1Philip Prindeville2018-10-252-1/+76
| | | | | | | | | | | | | grub-efi no longer works: grub-mkimage: error: relocation 0x4 is not implemented yet. See: http://git.savannah.gnu.org/cgit/grub.git/commit/util?id=842c390469e2c2e10b5aa36700324cd3bde25875 Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>i [PKG_RELEASE increase]
* sunxi: add support for Orange Pi ZeroJulian Haupt2018-10-071-0/+7
| | | | Signed-off-by: Julian Haupt <julian.haupt@hauptmedia.de>
* uboot-lantiq: fix compile with modern host dtcThomas Nixon2018-10-071-0/+19
| | | | | | | | In dtc version 1.4.6 the macro names in header include guards changed, but the build relies on them matching in order to replace selected headers. This is a horrible hack to work around this. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* uboot-envtools: adds r7800 uboot env supportAnsuel Smith2018-10-072-1/+4
| | | | | | This fix and adds support for r7800 uboot env Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* uboot-lantiq: fix compatibility with gcc7Martin Schiller2018-09-261-0/+142
| | | | | | | Backport u-boot commit 704f3acfcf55343043bbed01c5fb0a0094a68e8a to fix compatibility with gcc7. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* layerscape: add ls1012afrwy support and drop ls1012afrdmYangbo Lu2018-09-224-18/+18
| | | | | | | | | | | | | | | | | | | | | | | ls1012afrdm was no longer supported in NXP Layerscape SDK. Instead a new board ls1012afrwy was introduced in LSDK. This patch is to drop ls1012afrdm and add ls1012afrwy support. Since only 2MB NOR flash could be used, we just put u-boot and firmware on NOR flash, and put kernel/dtb/rootfs on SD card. The Layerscape FRWY-LS1012A board is an ultra-low-cost development platform for LS1012A Series Communication Processors built on Arm Cortex-A53. This tool refines the FRDM-LS1012A with more features for a better hands-on experience for IoT, edge computing, and various advanced embedded applications. Features include easy access to processor I/O, low-power operation, micro SD card storage, an M2 connector, a small form factor, and expansion board options via mikroBUS Click Module. The MicroBUS Module provides easy expansion via hundreds of powerful modules supporting sensors, actuators, memories, and displays. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add SD card boot supportYangbo Lu2018-09-225-1/+67
| | | | | | | | | NOR/QSPI Flash on Layerscape board only has limited 64MB memory size. Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr) could support SD card boot, we added SD boot support for them to put all things on SD card to meet large memory requirement. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add armv7 subtarget and ls1021atwr board supportYangbo Lu2018-09-222-1/+17
| | | | | | | | | | | | | | | | | | The NXP TWR-LS1021A module is a development system based on the QorIQ LS1021A processor. - This feature-rich, high-performance processor module can be used standalone or as part of an assembled Tower System development platform. - Incorporating dual Arm Cortex-A7 cores running up to 1 GHz, the TWR-LS1021A delivers an outstanding level of performance. - The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as well as a complete Linux software developer's package. - The module provides a comprehensive level of security that includes support for secure boot, Trust Architecture and tamper detection in both standby and active power modes, safeguarding the device from manufacture to deployment. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add u-boot environment support for OpenWrt bootYangbo Lu2018-09-228-1/+70
| | | | | | | This patch is to implement u-boot environment txt files to support OpenWrt boot for all layerscape devices. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update u-boot to LSDK-18.06Yangbo Lu2018-09-222-49/+71
| | | | | | | | | | | | | | The u-boot source code had been migrated to codeaurora for LSDK-18.06 release and the future release. This patch is to update u-boot to LSDK-18.06 for both uboot-layerscape and uboot-layerscape-armv8_32b packages. Besides, this patch also introduced some other changes. - Reworked uboot-layerscape makefile to make it more readable. - Define package in uboot-layerscape-armv8_32b for each board. - Fixed u-boot package selection in target image makefile. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: drop uboot-layerscape patchesYangbo Lu2018-09-226-320/+0
| | | | | | | | Dropped uboot-layerscape patches which were environemnt patches. We will make u-boot environment binaries with a txt file for all devices. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* sunxi: build image/uboot for the NanoPi NEO2Jasper Scholte2018-09-221-0/+9
| | | | | | | | The NanoPi NEO2 is a small Allwinner H5 based board available with different DRAM configurations. This board is very similar to the NanoPi NEO PLUS2 Signed-off-by: Jasper Scholte <NightNL@outlook.com>
* uboot-zynq: use a file to modify the default environmentLuis Araneda2018-09-102-0/+3
| | | | | | | | | Follow the strategy of other targets and create a default environment file, uEnv.txt, to configure the behavior of U-Boot. For now, use it to pass bootargs to the kernel Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* uboot-zynq: copy U-Boot images to STAGING_DIRLuis Araneda2018-09-101-0/+9
| | | | | | | | | | | Create a directory inside STAGING_DIR and copy U-Boot output images, so they can be used later when creating the sdcard image Additionally, like others targets, override the default install method to avoid copying the images to bin directory Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* uboot-zynq: automatically select the appropriate variantLuis Araneda2018-09-101-0/+5
| | | | | | | | Select the U-Boot variant automatically based on the current selected device, and hide the package from menuconfig Signed-off-by: Luis Araneda <luaraneda@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 03:41:14 +0000