aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: support for TP-Link EAP225 v3Sander Vanheule2020-11-235-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access point. Serial port access for debricking requires fine soldering. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From OEM boot log: Using interface ath0 with hwaddr b0:...:3e and ssid "..." Using interface ath10 with hwaddr b0:...:3f and ssid "..." Tested by forum user blinkstar88 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: support for TP-Link EAP225-Outdoor v1Sander Vanheule2020-11-235-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall mount access point. Debricking requires access to the serial port, which is non-trivial. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (AR8033): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Tested by forum user PolynomialDivision on firmware v1.7.0. UART access tested by forum user arinc9. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: support for TP-Link EAP245 v1Sander Vanheule2020-11-235-5/+88
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9880): a/n/ac, 3x3 * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * Upgrade the device to firmware v1.4.0 if necessary * Exploit the user management page in the web interface to start telnetd by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`. * Immediately change the malformed username back to something valid (e.g. 'admin') to make ssh work again. * Use the root shell via telnet to make /tmp world writeable (chmod 777) * Extract /usr/bin/uclited from the device via ssh and apply the binary patch listed below. The patch is required to prevent `uclited -u` in the last step from crashing. * Copy the patched uclited programme back to the device at /tmp/uclited (via ssh) * Upload the factory image to /tmp/upgrade.bin (via ssh) * Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt. --- xxd uclited +++ xxd uclited-patched @@ -53796,7 +53796,7 @@ 000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... .......... 000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000 ...L..(!........ -000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010 .D....E.'....... +000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$........... 000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058 .@.....!...t<..X 000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809 <..V$...$..0. .. Debricking: * Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via the LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary patch might not apply to uclited from other firmware versions. EAP245 v1 device support was originally developed and maintained by Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port TP-Link EAP2x5 devices" are based on that work. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: prepare for 1-port TP-Link EAP2x5 devicesSander Vanheule2020-11-231-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link has developed a number of access points based on the AP152 reference board. In the EAP-series of 802.11ac access points, this includes the following devices with one ethernet port: * EAP225 v1/v2 * EAP225 v3 * EAP225-Outdoor v1 * EAP245 v1 Since the only differences between these devices are the ath10k wireless radios and LEDs, a common base is provided for the overlapping support requirements. Hardware commonalities: * SoC: QCA9563-AL3A MIPS 74kc v5.0 @ 775MHz, AHB @ 258MHz * RAM: 128MiB DDR2 @ 650MHz * Flash: 16MiB SPI NOR * Wi-Fi 2.4GHz: provided by SoC * Wi-Fi 5Ghz: ath10k chip on PCIe * Ethernet: AR8033-AL1A, one 1GbE port (802.3at PoE) Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: add QCA956x SERDES init workaroundJulien Dusser2020-11-231-0/+76
| | | | | | | | | | | | | | | | | | | | | | | This commit add a workaround for non working SGMII link observed on some QCA956x SoCs. The workaround originates part from the U-Boot source code from QCA, part from the implementation from TP-Link found in the GPL tarball for the EAP245v1. Extends commit 0d416a8d3b990e3b78628f0e7546527709c877f7 for QCA956x. Note that reset is the same on QCA955x and QCA956x, same register offset and values. Auto calibration is done on u-boot, but always fall back to default value 0x7. Add a DTS entry serdes-cal in case a device require another value. Signed-off-by: Julien Dusser <julien.dusser@free.fr> [Sander Vanheule: Minor code style fixes, Remove hunk adding qca956x-serdes-fixup to a missing DTS, Remove variable err that was only assigned, Rename function to sgmii_serdes_init, Lower priority of serdes call message to pr_debug] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: ensure QCA956x gmac0 mux selects sgmiiSander Vanheule2020-11-231-0/+35
| | | | | | | | | Some bootloaders do not set up gmac0 properly, leaving it disconnected from the sgmii interface. If the user specificies phy-mode sgmii, then use the gmac-config/device node to ensure the mux is configured correctly. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mvebu: add initial support for Globalscale ESPRESSObin-UltraVladimir Vid2020-11-236-1/+260
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses the same Armada-3720 SoC with extended hardware support. - SoC: Armada-3720 - RAM: 1 GB DDR4 - Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC - Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE) - WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB) - 1x USB 2.0 port - 1x USB 3.0 port - 1x microSD slot - 1x mini-PCIe slot (USB [with nano-sim slot]) - 1x mini-USB debug UART - 1x RTC Clock and battery - 1x reset button - 1x power button - 4x LED (RGBY) - Optional 1x M.2 2280 slot ** Installation ** Copy dtb from build_dir to bin/ and run tftpserver there: $ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/ linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb bin/targets/mvebu/cortexa53/ $ in.tftpd -L -s bin/targets/mvebu/cortexa53/ Connect to the device UART via microUSB port on the back side and power on the device. Power on the device and hit any key to stop the autoboot. Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g: $ setenv serverip 192.168.1.10 # Host $ setenv ipaddr 192.168.1.15 # Device Ping server to confirm network is working: $ ping $serverip Using neta@30000 device host 192.168.1.15 is alive Tftpboot the firmware: $ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin $ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb Set the console and boot the image: $ setenv bootargs $console $ booti $kernel_addr_r - $fdt_addr_r Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz to /tmp dir on the device. Gunzip and dd the image: $ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz $ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync Reboot the device. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* hostapd: fix patch offsetLeon M. George2020-11-231-1/+1
| | | | | | | Fixes the offset of the patch added in 93bbd998aa696a ("hostapd: enter DFS state if no available channel is found"). Signed-off-by: Leon M. George <leon@georgemail.eu>
* layerscape: enable spi-uart in LS1012A-FRDMPawel Dembicki2020-11-234-1/+76
| | | | | | | | | This patch add missing support of SC16IS740 serial controller, installed on LS1012A-FRDM board. It was required to change RCW bits, because SPI was disabled by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: add i2c peripherials on LS1012A-RDBPawel Dembicki2020-11-234-0/+141
| | | | | | | | | | | | LS1012A-RDB equipped in some i2c devices: - 3x GPIO Expander: PCAL9555A (NXP) - Gyro: FXAS21002 (NXP) - Accelerometer: FXOS8700 (NXP) - Current & Power Monitor: INA220 (TI) This patch enables i2c peripherials installed on LS1012A-RDB. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: iio: add fxas21002c driver supportPawel Dembicki2020-11-231-0/+50
| | | | | | This patch adds kernel modules for Freescale FXAS21002C 3-axis gyro driver. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: make initramfs kernel fit packedPawel Dembicki2020-11-237-9/+7
| | | | | | | | This will make developing process easier, because dtb will be included into image. Not need to enable initramfs image by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: phy: at803x: Select SFP interface mode that both sides supports.René van Dorst2020-11-231-16/+35
| | | | | | | | | | | | | | | | Currently sfp_select_interface() return the fastest interface that the sfp modules supports even if the phy don't support that mode. For example an GPON module that support both 2500basex and 1000basex. Currently sfp_select_interface() picks 2500basex instead of 1000basex. So limit the interfaces which both sides supports before calling sfp_select_interface() or return an error if we don't have match. Reviewed-by: John Thomson <git@johnthomson.fastmail.com.au> Tested-by: Braihan Cantera <bcanterac@gmail.com> [MikroTik RB760iGS + Nokia G-010S-A 3FE46541AA SFP] Tested-by: John Thomson <git@johnthomson.fastmail.com.au> [Mikrotik rb760igs + SFP SM/LC, SFP base1000T, SFP+ passive DAC] Signed-off-by: René van Dorst <opensource@vdorst.com>
* linux-firmware: update to 20201118John Audia2020-11-231-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20201022..20201118 2ea8667 (tag: 20201118) rtlwifi: v88.2 firmware files for RTL8192CU e850cf3 Merge https://github.com/rjliao-qca/qca-btfw into main 65370db rtw88: RTL8822C: Update firmware to v9.9.4 e371b7c Revert "rtw88: RTL8822C: Update firmware to v9.9.4" 51d2c81 vpdma: Move firmware to ti directory d7a24c9 Merge branch 'master' of https://github.com/shahasit/video-linux-firmware into main 9ee1543 Merge branch 'master' of https://github.com/shahasit/bt-linux-firmware into main 3bcc4c1 amdgpu: update picasso VCN firmware b6b4542 amdgpu: update raven2 VCN firmware 79aa335 amdgpu: update raven VCN firmware c93834e rtw88: RTL8822C: Update firmware to v9.9.4 3ef6c93 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099A_281A b503c96 Merge branch 'ath10k-20201023' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware into main 463fdea QCA: Update Bluetooth firmware for QCA6390 8a46c32 qcom : updated venus firmware files for v5.4 d7793e5 QCA : Fixed BT SSR due to command timeout / IO fatal error d842d8c ath11k: QCA6390 hw2.0: add to WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 8fb1a6e ath11k: QCA6390 hw2.0: add board-2.bin 34cb5fc ath11k: IPQ8074 hw2.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 c0a8efd ath11k: IPQ8074 hw2.0: add board-2.bin ac7f5e9 ath11k: IPQ6018 hw1.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 2594e51 ath11k: IPQ6018 hw1.0: add board-2.bin d8f10d4 ath10k: QCA6174 hw3.0: add firmware-sdio-6.bin version WLAN.RMH.4.4.1-00077 6652297 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00131 36059aa ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00131 1e5629d ath10k: QCA6174 hw3.0: update board-2.bin e315d1a ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00157-QCARMSWPZ-1 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: mtd: parser: cmdline: Fix parsing of part-names with colonsSven Eckelmann2020-11-231-0/+63
| | | | | | | | | | | | | | | | | | | | | | Some devices (especially QCA ones) are already using hardcoded partition names with colons in it. The OpenMesh A62 for example provides following mtd relevant information via cmdline: root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait The change to split only on the last colon between mtd-id and partitions will cause newpart to see following string for the first partition: KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) Such a partition list cannot be parsed and thus the device fails to boot. Avoid this behavior by making sure that the start of the first part-name ("(") will also be the last byte the mtd-id split algorithm is using for its colon search. Fixes: d6a9a92e3217 ("kernel: bump 5.4 to 5.4.69") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: DTS style updates for OpenMesh devicesSven Eckelmann2020-11-233-47/+18
| | | | | | | | | | | | | | | | | The OpenMesh related files were not updated since a while and the new coding style requirements weren't integrated. This can cause problems for new devices when an author uses these files as starting point. * use SPDX-License-Identifiers instead of full license texts * drop linux,default-trigger with value default-off for LEDs * led nodes with label "abc:xyz" should have name "xyz_abc" * led DT labels for "xyz_abc" should be "led_xyz_abc" * "m25p80@0" flash node should be renamed to "flash@0" * drop unnecessary empty lines Signed-off-by: Sven Eckelmann <sven@narfation.org> [minor commit title and message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move the squashfs feature to the parent targetRui Salvaterra2020-11-235-5/+4
| | | | | | | All subtargets define it. Move it to the parent target and remove it from all subtargets. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* netifd: update to the latest versionFelix Fietkau2020-11-231-3/+3
| | | | | | | 213748a9bcd9 system-linux: implement full device present state management for force-external devices 3abe1fc87151 system-linux: add retry for adding member devices to a bridge Signed-off-by: Felix Fietkau <nbd@nbd.name>
* imagebuilder: fix main entry makefilePaulo Machado2020-11-231-1/+1
| | | | | | | Remove a syntax error from ImageBuider Makefile Acked-by: Paul Spooren <mail@aparcar.org> Signed-off-by: Paulo Machado <pffmachado@yahoo.com>
* hostapd: enable the epoll-based event loopRui Salvaterra2020-11-238-8/+8
| | | | | | Hostapd supports epoll() since 2014. Let's enable it for better performance. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* uhttpd: update to git HEADDaniel Golle2020-11-231-4/+4
| | | | | | f53a639 ubus: fix uhttpd crash Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for TP-Link MR6400 v4Filip Moc2020-11-234-0/+121
| | | | | | | | | | | | | | | | | | | | | | | You can flash via tftp recovery: - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24 - connect to any ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button Flashing via OEM web interface does not work. LTE module does not support DHCP so it must be configured via QMI. Hardware Specification (v4.0 EU): - SoC: MT7628NN - Flash: Winbond W25Q64JVS (8MiB) - RAM: ESMT M14D5121632A (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 1NIC (4x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 9V 0.85A Signed-off-by: Filip Moc <lede@moc6.cz>
* generic: add DTR quirk patch for MR400 LTEFilip Moc2020-11-231-0/+34
| | | | | | This is required for LTE module MR400 in TL-MR6400 v4. Signed-off-by: Filip Moc <lede@moc6.cz>
* procd: update to git HEADDaniel Golle2020-11-231-3/+3
| | | | | | | d4d78db uxc: also delete procd runtime state on 'delete' e935c0c jail: add 'debug' extern variable to preload_seccomp Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uqmi: update to git HEADDaniel Golle2020-11-221-4/+4
| | | | | | | 65796a6 nas: add --get-plmn 0a19b5b uqmi: add timeout parameter Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uqmi: set device-operating-mode to onlineFilip Moc2020-11-222-1/+4
| | | | | | | This is required for LTE module MR400 (in TL-MR6400 v4). Otherwise LTE module won't register to GSM network. Signed-off-by: Filip Moc <lede@moc6.cz>
* uqmi: add support for IPv4 autoconf from QMIFilip Moc2020-11-222-12/+39
| | | | | | | | | | | There already was an option for autoconfiguring IPv4 from QMI but this was removed by commit 3b9b963e6e08 ("uqmi: always use DHCP for IPv4"). DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd support for IPv4 autoconf from QMI but this time allow to configure this for IPv4 and IPv6 independently and keep DHCP default on IPv4. Signed-off-by: Filip Moc <lede@moc6.cz>
* uqmi: wait forever registration if timeout set to 0Thomas Richard2020-11-221-2/+2
| | | | | | | | | | | Give possibility to wait forever the registration by setting timeout option to 0. No timeout can be useful if the interface starts whereas no network is available, because at the end of timeout the interface will be stopped and never restarted. Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
* Revert "refpolicy: add variant that builds modular policy"Daniel Golle2020-11-222-39/+2
| | | | | | | | | | This reverts commit 9eb9943f82e0b2d5e32ffe1c63f5a82caca5094d. Building the 'modular' variant requires 'semodule_package' from 'selinux-python' to be installed on the buildhost. Apart from that, this change also broke the monolithic refpolicy 'targeted' build. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2020-11-221-3/+3
| | | | | | | | | 04a2edd uxc: make force-delete kill container process be6da62 seccomp: silence 'unknown syscall' warnings b22e625 jail: cgroup hack: rewrite cgroup -> cgroup2 df7fa7b uxc: fix incomplete commit Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tools/mpc: update to 1.2.1Hannu Nyman2020-11-211-2/+2
| | | | | | | | | | | Update mpc to 1.2.1 http://www.multiprecision.org/mpc/ Bug fixes: Fix an incompatibility problem with GMP 6.0 and before. Fix an intermediate overflow in asin. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/gmp: update to 6.2.1Hannu Nyman2020-11-211-2/+2
| | | | | | | | Update gmp to 6.2.1 Release notes: https://gmplib.org/gmp6.2 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/bison: update to 3.7.4Hannu Nyman2020-11-212-6/+6
| | | | | | | | | Update bison to 3.7.4 Release notes: http://git.savannah.gnu.org/cgit/bison.git/tree/NEWS?id=7a11a9308cb Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/cmake: update to 3.18.5Hannu Nyman2020-11-212-3/+3
| | | | | | Update cmake to 3.18.5 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/expat: update to 2.2.10Hannu Nyman2020-11-211-2/+2
| | | | | | Update expat to 2.2.10 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* netifd: update to the latest versionFelix Fietkau2020-11-211-3/+3
| | | | | | | | | 351d690f1a09 wireless: fix passing bridge name for vlan hotplug pass-through c1c2728946b5 config: initialize bridge and bridge vlans before other devices 5e18d5b9ccb1 interface: do not force link-ext hotplug interfaces to present by default 4544f026bb09 bridge-vlan: add support for defining aliases for vlan ids Signed-off-by: Felix Fietkau <nbd@nbd.name>
* musl: handle wcsnrtombs destination buffer overflow (CVE-2020-28928)Petr Štetiar2020-11-202-1/+66
| | | | | | | | | | | | | | | | | | The wcsnrtombs function in all musl libc versions up through 1.2.1 has been found to have multiple bugs in handling of destination buffer size when limiting the input character count, which can lead to infinite loop with no forward progress (no overflow) or writing past the end of the destination buffera. This function is not used internally in musl and is not widely used, but does appear in some applications. The non-input-limiting form wcsrtombs is not affected. All users of musl 1.2.1 and prior versions should apply the attached patch, which replaces the overly complex and erroneous implementation. The upcoming 1.2.2 release will adopt this new implementation. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* scripts: download.pl: retry download using filenameDavid Bauer2020-11-201-2/+6
| | | | | | | | | | | | | | | | With this commit, the download script will try downloading source files using the filename instead of the url-filename in case the previous download attempt using the url-filename failed. This is required, as the OpenWrt sources mirrors serve files using the filename files might be renamed to after downloading. If the original mirror for a file where url-filename and filename do not match goes down, the download failed prior to this patch. Further improvement can be done by performing this only for the OpenWrt sources mirrors. Signed-off-by: David Bauer <mail@david-bauer.net>
* imagebuilder: add package signature verificationPaul Spooren2020-11-192-2/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ImageBuilder downloads pre-built packages and adds them to images. This process uses `opkg` which has the capability to verify package list signatures via `usign`, as enabled per default on running OpenWrt devices. Until now this was disabled for ImageBuilders because neither the `opkg` keys nor the `opkg-add` script was present during first packagelist update. To harden the ImageBuilder against *drive-by-download-attacks* both keys and verification script are added to the ImageBuilder allowing `opkg` to verify downloaded package indices. This commit adds `opkg-add` to the ImageBuilder scripts folder. The keys folder is added to ImageBuilder $TOPDIR to have an obvious place for users to store their own keys. The `option check_signature` is appended to the repositories.conf file. All of the above only happens if the Buildbot runs with the SIGNATURE_CHECK option. The keys stored in the ImageBuilder keys/ are the same as included in the openwrt-keyring package. To avoid the chicken-egg problem of downloading and verifying a package, containing signing keys, the keys are added during the ImageBuilder generation. They are same as in shipped images (stored at `/etc/opkg/keys/`). To allow a local package feed in which the user can add additional packages, a local set of `usign` and `ucert` keys is generated, same as building OpenWrt from source. The private key signs the local repository inside the packages/ folder. The local public key is added to the keys/ folder to be considered by `opkg` when updating repositories. This way a local package feed can be modified while requiring `opkg` to check signatures for remote feed, making HTTPS optional. The new option `ADD_LOCAL_KEY` allows to add the local key inside the created images, adding the advantage that sysupgrades can validate the ImageBuilders local key. Signed-off-by: Paul Spooren <mail@aparcar.org>
* build: create $(PKG_SYMVERS_DIR) if non-existentSebastian Kemper2020-11-192-1/+1
| | | | | | | | | | | | | Commit 5d76065 moved the creation of the symvers directory to include/kernel-build.mk. This is fine when building from scratch. But when unpacking an SDK the directory doesn't exist and because the kernel won't be built (again) this directory will not be created by the build system, causing build failure if make tries to copy files into it. This moves the creation of the symvers directory back into include/kernel.mk so that the directory is created in any case. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
* base-files: generated named bridge-vlan sectionsJohn Crispin2020-11-191-7/+8
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for the Hak5 WiFi Pineapple Mark 7Marc Egerton2020-11-183-0/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WiFi Pineapple Mark 7, a wireless penetration testing tool. Specifications: * SoC: MediaTek MT7628 (580MHz) * RAM: 256MiB (DDR2) * Storage 1: 32MiB NOR (SPI) * Storage 2: 2GB eMMC * Wireless 1: 802.11b/g/n 2.4GHz (Built In) * Wireless 2: 802.11b/g/n 2.4GHz (MT7601) * Wireless 3: 802.11b/g/n 2.4GHz (MT7601) * USB: 1x USB Type-A 2.0 Host Port * Ethernet: 1x USB Type-C AX88772C Ethernet * UART: 57600 8N1 on PCB * Inputs: 1x Reset Button * Outputs: 1x RGB LED * FCCID: 2AA52MK7 Flash Instructions: Original firmware is based on OpenWRT. Use sysupgrade via SSH to flash. Signed-off-by: Marc Egerton <foxtrot@realloc.me> [pepe2k@gmail.com: set only required/used gpio groups to gpio function] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: fix reset button support on 8devices LimaPiotr Dymacz2020-11-181-1/+1
| | | | | | | | | | This fixes 'linux,code' property name and value for the 'reset' key node in 8devices Lima DTS file. Problem and solution were reported on the forum, see: https://forum.openwrt.org/t/resetbutton-not-working-ath79-8devices-lima/78810 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: calculate Eth MACs from WLAN on ALFA Network R36APiotr Dymacz2020-11-181-2/+4
| | | | | | | | New batches of the R36A board series might no longer keep separated Ethernet MAC addresses stored in flash. Use same approach as on the N2Q and calculate Ethernet MACs from WLAN one which is kept in ART. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ath79: add support for ALFA Network Pi-WiFi4Piotr Dymacz2020-11-181-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for ALFA Network Pi-WiFi4Piotr Dymacz2020-11-184-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet - 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM - 2x IPEX/U.FL connectors on PCB - 4x USB 2.0 Type-A - Genesys Logic GL850G 4-port USB HUB - USB power is controlled by GPIO - 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - 1x micro USB Type-B for power and system console (Holtek HT42B534) - UART and GPIO (8-pin, 1.27 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add label MAC address for ALFA Network N5QPiotr Dymacz2020-11-181-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* scripts: add const_structs.checkpatch for checkpatch.plAdrian Schmutzler2020-11-181-0/+68
| | | | | | | | | | | | | | | | | | Kernel has separated the structs that are reported to be const in checkpatch.pl into a file of its own, const_structs.checkpatch. This file has been missing after the recent update of checkpatch.pl, leading to the following message: No structs that should be const will be found - file '/data/openwrt/scripts/const_structs.checkpatch': No such file or directory This commit adds the relevant file from v5.10-rc4. Fixes: 086ee09bbcac ("scripts: Update checkpatch.pl to 2020-06-11") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* scripts: checkpatch.pl: suppress warnings about MAINTAINERSAdrian Schmutzler2020-11-181-1/+1
| | | | | | | | | | | | | | | | | | | The kernel expects changes to MAINTAINERS for all removed or added files, printing warnings like: WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? #828: deleted file mode 100644 Since this does not apply to "our" files in OpenWrt repo, this warning should be disabled. This can be achieved easiest by setting $reported_maintainer_file to 1. While this is a hack that tricks the script into believing the proper MAINTAINERS changes have been made, it's the easiest solution as it does not require to touch any other code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use m25p,fast-read on Xiaomi Mi Router 4A Gb/3G v2Adrian Schmutzler2020-11-181-0/+1
| | | | | | | | | | | The Xiaomi Mi Router 4A Gigabit model has a race condition on bootup causing the SQUASHFS data errors to appear and create a bootloop scenario. Adding the m25p,fast-read property resolves this issue. Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 20:18:19 +0000