aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: ZTE MF286[,A,R]: use GPIO19 as ath9k LEDLech Perczak2022-06-051-14/+7
| | | | | | | | | | | | With the pinctrl configuration set properly by the previous commit, the LED stays lit regardless of status of 2.4GHz radio, even if 5GHz radio is disabled. Map GPIO19 as LED for ath9k, this way the LED will show activity for both bands, as it is bound by logical AND with output of ath10k-phy0 LED. This works well because during management traffic, phy*tpt triggers typically cause LEDs to blink in unison. Link: <https://github.com/openwrt/openwrt/pull/9941> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ZTE MF286[,A,R]: fix WLAN LED mappingLech Perczak2022-06-051-0/+8
| | | | | | | | | | The default configuration of pinctrl for GPIO19 set by U-boot was not a GPIO, but an alternate function, which prevented the GPIO hog from working. Set GPIO19 into GPIO mode to allow the hog to work, then the ath10k LED output can control the state of actual LED properly. Link: <https://github.com/openwrt/openwrt/pull/9941> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: add support for Linksys WHW01 v1Peter Adkins2022-06-058-5/+362
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Link: https://github.com/openwrt/openwrt/pull/3682 Signed-off-by: Peter Adkins <peter@sunkenlab.com> (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: remove patch to fix vlan setup on mv88e6xxxJosef Schlehofer2022-06-051-27/+0
| | | | | | | | | | | | This patch was present in Linux kernel [1] since version 5.11rc1, but it was superseded by another patch, which set configure_vlan_while_not_filtering to true by default since kernel v5.12-rc2 [2]. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/net/dsa/mv88e6xxx/chip.c?h=v5.15.41&id=b8b79c414eca4e9bcab645e02cb92c48db974ce9 [2] https://github.com/torvalds/linux/commit/0ee2af4ebbe3c4364429859acd571018ebfb3424# Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* kernel: move Toshiba-TC58NVG0S3H patch to ipq40xxChristian Lamparter2022-06-052-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hannu Nyman wrote in openwrt's github issue #9962: |Based on forum discussion, the commit 0bc794a |"kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash" |causes flash memory chip misdetection for some other |Fritzbox devices, as the commit only defines a 4-byte flash |memory chip ID that matches several chips used in the devices. | |See discussion from this onward |<https://forum.openwrt.org/t/openwrt-22-03-0-rc1-first-release-candidate/126045/182> | |OpenWrt 22.03.0-rc2 and rc3 are causing on a Fritzbox 7412 |bootloops due to a misdetected flash chip. | |Yup, that patch is missing the 5th ID byte entirely - both chips |share the same first 4; | | TC58NVG0S3HTA00 = 0x98 0xf1 0x80 0x15 0x72 (digikey datasheet, page 35) | TC58BVG0S3HTA00 = 0x98 0xf1 0x80 0x15 0xf2 (digikey datasheet, page 28) | |The commit has also been backported to openwrt-22.03 after rc1, |so both rc2 and rc3 suffer from this bug." Andreas' TC58NVG0S3H seems not to follow Toshibas/Kioxa's own datasheet. It only reports the first four bytes: "98 f1 80 15 00 00 00 00". This patch changes the id_len in the entry to 8. This makes it so that Andreas' NAND is still detected. At the same time, this prevents other Toshiba NAND flash chips - that share the same four bytes - from being misdetected. The issue has been reported upstream, since they also accepted the initial patch... so if not addressed, 5.19/5.20 will also break those affected devices again. Reported-by: Peter-vdL Fixes: 0bc794a66845 ("kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash") Link: <https://github.com/openwrt/openwrt/issues/9962> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: modules: make ar8216/8327 modularizableChristian 'Ansuel' Marangi2022-06-053-6/+26
| | | | | | | Make ar8216/8327 swconfig driver modularizable and add entry to the netdevices.mk kernel modules file. Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* generic: 5.15: fix wrong PACKET_MANGLE select in swconfig switch patchChristian 'Ansuel' Marangi2022-06-051-1/+1
| | | | | | | | | In the rebase process of 5.15 hack patch the ETHERNET_PACKET_MANGLE got wrongly swapped from AR8216_PHY to PSB6970_PHY. Restore the ETHERNET_PACKET_MANGLE select to the right place. Fixes: 1f302afd7350 ("generic: 5.15: rework hack patch") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* build: fix find warning with SCAN_EXTRALeo Chung2022-06-051-1/+1
| | | | | | | | | | | | | | | | | | If you change SCAN_EXTRA variable with "-path target/linux/xxxx" in include/toplevel.mk for speed up scan, find will warn with: find: warning: you have specified the global option -maxdepth after the argument -path, but global options are not positional, i.e., -maxdepth affects tests specified before it as well as those specified after it. Please specify global options before other arguments. The find option -mindepth -maxdepth are global options and must be before any path option. Change order of $(SCAN_EXTRA) after -mindepth and -maxdepth to fix this. Signed-off-by: Leo Chung <gewalalb@gmail.com> [capitalize Description, Author and Sob and minor description tweak] Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* tools/mkimage: increase tmpfile name length limitDaniel Golle2022-06-051-0/+11
| | | | | | | | mkimage limits the length of the file paths in can deal with to 256 characters. Turns out that in automated builds by asu we break this limit, so increase it to 1024 characters. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi/cortexa53: enable armv8-CE crypto algorithmsEneas U de Queiroz2022-06-042-0/+20
| | | | | | | This enables armv8 crypto extensions version of AES, GHASH, SHA1, and CRC T10 algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* sunxi/cortexa53: refresh kernel 5.15 configEneas U de Queiroz2022-06-041-8/+6
| | | | | | | | | This is result of a make kernel_oldconfig CONFIG_TARGET=subtarget. One new option popped up: Support for the Allwinner H616 CCU (SUN50I_H616_CCU) [Y/n/?] (NEW) n Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* rockchip/armv8: enable armv8-CE crypto algorithmsEneas U de Queiroz2022-06-041-0/+9
| | | | | | | This enables armv8 crypto extensions version of AES, GHASH, and CRC T10 algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* octeontx: add armv8-CE version of CRC T10Eneas U de Queiroz2022-06-041-0/+1
| | | | | | | Adds the crypto extensions version of the CRC T10 algorithm that is already built into the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mvebu/cortexa72: enable armv8-CE crypto algosEneas U de Queiroz2022-06-041-0/+11
| | | | | | | | | | | This enables armv8 crypto extensions version of AES, GHASH, SHA1, SHA256, and SHA512 algorithms in the kernel. The choice of algorithms match the 32-bit versions that are enabled in the target config-5.10 file, but were only used by the cortexa9 subtarget. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mvebu/cortexa72: refresh kernel 5.10 configEneas U de Queiroz2022-06-041-1/+3
| | | | | | This is result of a plain make kernel_oldconfig CONFIG_TARGET=subtarget. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mvebu/cortexa53: enable armv8-CE crypto algosEneas U de Queiroz2022-06-041-0/+11
| | | | | | | | | | | This enables armv8 crypto extensions version of AES, GHASH, SHA1, SHA256, and SHA512 algorithms in the kernel. The choice of algorithms match the 32-bit versions that are enabled in the target config-5.10 file, but were only used by the cortexa9 subtarget. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mvebu/cortexa53: refresh kernel 5.10 configEneas U de Queiroz2022-06-041-1/+6
| | | | | | This is result of a plain make kernel_oldconfig CONFIG_TARGET=subtarget. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* layerscape/armv8_64b: enable armv8-CE crypto algosEneas U de Queiroz2022-06-041-0/+11
| | | | | | | This enables armv8 crypto extensions version of AES, GHASH, SHA256 and CRC T10 algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* bcm4908: enable armv8-CE crypto algorithmsEneas U de Queiroz2022-06-041-0/+8
| | | | | | | This enables armv8 crypto extensions version of AES and GHASH algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* bcm27xx/bcm2711: enable asm crypto algorithmsEneas U de Queiroz2022-06-041-0/+8
| | | | | | | | This enables arm64/neon version of AES, SHA256 and SHA512 algorithms in the kernel. bcm2711 does not support armv8 crypto extensions, so they are not included. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* bcm27xx/bcm2710: enable asm crypto algorithmsEneas U de Queiroz2022-06-041-0/+8
| | | | | | | | This enables arm64/neon version of AES, SHA256 and SHA512 algorithms in the kernel. bcm2710 does not support armv8 crypto extensions, so they are not included. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mac80211: add airtime fairness rework/fixesFelix Fietkau2022-06-043-2/+986
| | | | | | | latency and short-term fairness is improved by fixing the tx queue sorting so that it considers the pending AQL budget Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-032-2/+4
| | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
* kernel: crypto: add kmod-crypto-chacha20poly1305Xu Wang2022-06-031-0/+12
| | | | | | | | Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used by wireguard. Signed-off-by: Xu Wang <xwang1498@gmx.com>
* mt76: update to the latest versionFelix Fietkau2022-06-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 6da21a0b7280 linux-firmware: update firmware for MT7921 WiFi device 4876688c41dc linux-firmware: update firmware for MT7915 79b1b86040de linux-firmware: add firmware for MT7986 784c27b159b9 linux-firmware: add firmware for MT7922 079e41dc71a1 mt76: mt7915: configure soc clocks in mt7986_wmac_init 747c70fc6c89 mt76: connac: use skb_put_data instead of open coding e98f58815018 mt76: mt7915: update mt7986 patch in mt7986_wmac_adie_patch_7976() b7104b4b2f2d mt76: mt7915: fix twt table_mask to u16 in mt7915_dev d39368f336ee mt76: mt7915: reject duplicated twt flows 4718ed04a655 mt76: mt7915: limit minimum twt duration 84319691b742 mt76: mt7915: reowrk SER debugfs knob bac5f22365a2 mt76: mt7915: introduce mt7915_mac_severe_check() 81524067686c mt76: mt7915: move MT_INT_MASK_CSR to init.c 2b7f5e85290e mt76: mt7915: add support for 6G in-band discovery 31273183ea0a mt76: mt7615/mt7915: do reset_work with mt76's work queue bb54f5e1c115 mt76: mt7915: improve error handling for fw_debug knobs 838529da6470 mt76: mt7915: add more statistics from fw_util debugfs knobs 3a65deb93737 mt76: add gfp to mt76_mcu_msg_alloc signature 8e87669eefcf mt76: mt7921: add ipv6 NS offload support e1b2c18eee29 mt76: mt7915: fix endianness in mt7915_rf_regval_get 0742eaeafee2 mt76: mt76x02u: fix possible memory leak in __mt76x02u_mcu_send_msg d299ad96d867 mt76: mt7915: fix endian bug in mt7915_rf_regval_set() 380eac6f31ec mt76: add 6 GHz band support in mt76_sar_freq_ranges 268ce38e9e36 mt76: mt7921: introduce ACPI SAR support 8c27300b4271 mt76: mt7921: introduce ACPI SAR config in tx power 54b6504a3ef8 mt76: mt7915: add more ethtool stats cdd66d642977 mt76: add DBDC rxq handlings into mac_reset_work b284684f5cba mt76: mt7921: add PATCH_FINISH_REQ cmd response handling f8b9be4287cc mt76: mt7921s: fix firmware download random fail 28b19d2cc53f mt76: mt7915: add missing bh-disable around tx napi enable/schedule 1d8af168e86f mt76: mt7615: add missing bh-disable around rx napi enable/schedule Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add a bug fix for a rare crashFelix Fietkau2022-06-021-0/+38
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix crashes in bridge offload codeFelix Fietkau2022-06-022-10/+10
| | | | | | - fix an issues when accessing the port pointer of an expired/invalid fdb entry Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: add Aruba AP-365 specific BDFDavid Bauer2022-06-024-1/+12
| | | | | | | | | | | | | Aruba deploys a BDF in the root filesystem, however this matches the one used for the DK04 reference board. The board-specific BDFs are built into the kernel. The AP-365 shows sinificant degraded performance with increased range when used with the reference BDF. Replace the BDF with the one extracted from Arubas kernel. Signed-off-by: David Bauer <mail@david-bauer.net>
* fstools: update to git HEADDaniel Golle2022-06-021-3/+3
| | | | | | 93369be Revert "fstools: remove SELinux restorecon hack" Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ubus: update to git HEADDaniel Golle2022-06-011-4/+4
| | | | | | | 2f793a4 lua: add optional path filter to objects() method 2bebf93 ubusd: handle invoke on event object without data Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to git HEADDaniel Golle2022-06-011-3/+3
| | | | | | | 2e1fcf4 netifd: fix hwmode for 60g band 39ef9fe interface-ip: fix memory corruption bug when using jail network namespaces Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2022-06-011-3/+3
| | | | | | | 557c98e init: selinux: don't relabel virtual filesystems 7a00968 init: only relabel rootfs if started from initramfs Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* rpcd: update to latest Git HEADChristian 'Ansuel' Marangi2022-06-011-3/+3
| | | | | | | 1c48257 iwinfo: fix compilation error with GCC 12 [remove extra change in Makefile] Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* Revert "rpcd: update to latest Git HEAD"Christian 'Ansuel' Marangi2022-06-011-8/+3
| | | | This reverts commit 8885cf88279fd131c163d0ac34aeeef0bbff0ceb.
* kernel: add two ksyms to the generic kconfigsRui Salvaterra2022-06-012-0/+4
| | | | | | These will be prompted for with GCC 12. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* toolchain: add support for GCC 12Rui Salvaterra2022-06-0120-2/+625
| | | | | | | | | | | | | | | | GCC 12.1 is out. Add support for it. Deleted (upstreamed): 011-v12-configure-define-TARGET_LIBC_GNUSTACK-on-musl.patch 931-libffi-fix-MIPS-softfloat-build-issue.patch Deleted (unneeded?) 970-macos_arm64-building-fix.patch Other patches manually rebased due to C++ conversion and consequent file name changing (.c to .cc). Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* rpcd: update to latest Git HEADChristian 'Ansuel' Marangi2022-06-011-3/+8
| | | | | | 1c48257 iwinfo: fix compilation error with GCC 12 Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* uhttpd: update to latest Git HEADChristian 'Ansuel' Marangi2022-06-011-3/+3
| | | | | | | d59d732 client: fix compilation error with GCC 12 51283f9 fix compiler uninitialized variable Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* toolchain: bump GCC 11 to 11.3.0Rui Salvaterra2022-06-0122-123/+9
| | | | | | Remove an upstreamed patch and rebase all remaining patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ucode: update to latest Git HEADJo-Philipp Wich2022-06-011-3/+3
| | | | | | | | d996047 syntax: adjust number literal parsing and string to number conversion 9efbe18 lib: refactor `uc_int()` Fixes: #9923 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: update to latest Git HEADJo-Philipp Wich2022-05-311-3/+3
| | | | | | | | | | | | | | 210991d fw4: prefer /dev/stdin if available 4e5e322 fw4: make `fw4 restart` behavior more robust 221040e ruleset: emit time ranges when both start and stop times are specified 30a7d47 fw4: fix datetime parsing fb9a6b2 ruleset: correct mangle_output chain type 6dd2617 fw4: fix logic flaw in testing hw flow offloading support c7c9c84 fw4: ensure that negative bitcounts are properly translated c4a78ed fw4: fix typo in emitted set types Fixes: #9764, #9923, #9927, #9935, #9955 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ucode: update to latest Git HEADJo-Philipp Wich2022-05-311-3/+3
| | | | | | | da3f089 lib: rework uc_index() implementation 559029e ci: make jobs faster during pull request testing Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* generic: 5.15: fix panic on tcp_no_window_check set with interface upChristian 'Ansuel' Marangi2022-05-291-39/+43
| | | | | | | | | | | The current reworked version cause kernel panic when the value is changes and an interface is up. Following the tcp_be_liberal impelementation, reimplement this to permit a safe change of this value without any panic. This has been tested with a QSDK package where tcp_no_window_check is used. Fixes: 92fb51bc9881 ("generic: 5.15: standardize tcp_no_window_check pending patch") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* realtek: don't unmask non-maskable GPIO IRQsSander Vanheule2022-05-301-0/+29
| | | | | | | | | | | | | | | | On uniprocessor builds, for_each_cpu(cpu, mask) will assume 'mask' always contains exactly one CPU, and ignore the actual mask contents. This causes the loop to run, even when it shouldn't on an empty mask, and tries to access an uninitialised pointer. Fix this by wrapping the loop in a cpumask_empty() check, to ensure it will not run on uniprocessor builds if the CPU mask is empty. Fixes: af6cd37f42f3 ("realtek: replace RTL93xx GPIO patches") Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reported-by: Robert Marko <robimarko@gmail.com> Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: fix label MAC address for D-Link DIR-825B1Sebastian Schaper2022-05-291-0/+1
| | | | | | | The label MAC address for DIR-825 Rev. B1 is the WAN address located at 0xffb4 in `caldata`, which equals LAN MAC at 0xffa0 incremented by 1. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ramips: disable unsupported background-radarDavid Bauer2022-05-292-0/+6
| | | | | | | | The UniFi 6 Lite as well as the Tenbay T-MB5EU do not have the third background-radar chain. For the Tenbay, the connector is present, however no antenna is connected to it. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: introduce BSS color collision detectionDavid Bauer2022-05-291-0/+118
| | | | | | | | | | | | | | | | | | Add ieee80211_rx_check_bss_color_collision routine in order to introduce BSS color collision detection in mac80211 if it is not supported in HW/FW (e.g. for mt7915 chipset). Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify BSS color collision detection is supported in HW/FW. Set this for ath11k which apparently didn't need this code. Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com> Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org [clarify commit message a bit, move flag to mac80211] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* malta: use default OpenWrt network configurationHauke Mehrtens2022-05-281-13/+0
| | | | | | | | | | | | | | | | Currently malta configures the first Ethernet device as WAN interface. If it finds a second one it will configure it as LAN. This commit reverses it to match armvirt and x86. If there is only one network device it will be configured as LAN device now. If we find two network devices the 2. one will be WAN. If no board.d network configuration is given it will be configured in package/base-files/files/etc/board.d/99-default_network Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [minor typos] Signed-off-by: Paul Spooren <mail@aparcar.org>
* uboot-imx: fix wrong make flags overridingPetr Štetiar2022-05-281-2/+2
| | | | | | | | | | | | | | | | | | | Buidbots are currently choking on the following compile error: In file included from tools/aisimage.c:9: include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory # include <openssl/evp.h> ^~~~~~~~~~~~~~~ compilation terminated. This is caused by a complete overriding of make flags which are provided correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden instead of extended. This then leads to the usage of build host include dirs, which are not available. Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: backport flow offload fixesRitaro Takenaka2022-05-274-2/+200
| | | | | | | | | Some dst in IPv6 flow offload table become invalid after the table is created. So check_dst is needed in packet path. Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com> [Add patch for kernel 5.15 too and rename file] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-15 13:54:52 +0000