aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for RT-N14U (mt7620n based) boardJohn Crispin2013-12-256-0/+132
| | | | | | | | | | | | | | | | | added dts file and userspace scripts modified to support Asus RT-N14U board current support status: usb works ethernet works buttons reset, wps leds asus:blue:[usb|lan|wan|air|power] i2c not tested uart not tested wifi not yet Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com> SVN-Revision: 39163
* ramips: add gpio pin 72 in mt7620 chips to dtsi filesJohn Crispin2013-12-252-0/+38
| | | | | | | | describes register set to control last gpio pin on mt7620 platfrom Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com> SVN-Revision: 39162
* ar71xx: fix max frame length of the QCA955x SoCsGabor Juhos2013-12-231-0/+11
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39161
* ar71xx: don't set builtin_switch flag for QCA9558Gabor Juhos2013-12-231-6/+1
| | | | | | | | It makes no sense, the SoC has no built-in switch. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39160
* x86/kvm_guest: remove 3.7 supportGabor Juhos2013-12-231-87/+0
| | | | | | | | Patch-by: Stijn Tintel <stijn@linux-ipv6.be> Patchwork: http://patchwork.openwrt.org/patch/4637/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39159
* x86/kvm_guest: remove 3.3 supportGabor Juhos2013-12-231-91/+0
| | | | | | | | Patch-by: Stijn Tintel <stijn@linux-ipv6.be> Patchwork: http://patchwork.openwrt.org/patch/46366/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39158
* x86/kvm_guest: add support for 3.10 and switch to itGabor Juhos2013-12-232-0/+97
| | | | | | | | Patch-by: Stijn Tintel <stijn@linux-ipv6.be> Patchwork: http://patchwork.openwrt.org/patch/4635/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39157
* hostapd: fix wep with netifdFelix Fietkau2013-12-231-4/+4
| | | | | | Signed-off-by: Catalin Patulea <cat@vv.carleton.ca> SVN-Revision: 39156
* wpa_supplicant: fix interface combination parsing issuesFelix Fietkau2013-12-211-0/+18
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39155
* opkg: switch to git repository (#14655)Jo-Philipp Wich2013-12-211-3/+3
| | | | | | | | | | Upstream development now takes place in a git repository which was clone from the old svn repository. Switch the source location to the git tree using the commit that corresponds to the old svn r618 revision. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39153
* dnsmasq: rework init procedureJo-Philipp Wich2013-12-213-11/+46
| | | | | | | | | | | - cache udhcp check results to speed up subsequent reloads - enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed - implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed - launch dnsmasq from interface hotplug to avoid race conditions with network bringup Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39152
* change fixup method and fix CFLAGS handlingImre Kaloz2013-12-203-3/+14
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39151
* ath9k: merge a timer handling fixesFelix Fietkau2013-12-201-6/+8
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39150
* ar71xx: allow to use large ethernet frames on AR934x SoCsGabor Juhos2013-12-201-0/+4
| | | | | | | | | | | | | | | The hardware supports large ethernet frames. Override the maximum frame length and packet lenght mask in the platform data to allow to use large MTU on the ethernet interfaces. Limit the feature to AR934x SoCs for now. It should work on some other SoCs as well, but those has not been tested yet. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39149
* ar71xx: ag71xx: fix max frame length setup of the built-in switchesGabor Juhos2013-12-201-5/+12
| | | | | | | | | | | | | The currently used bitmask of the maximum frame length field is wrong for both models. On AR724x/AR933x the largest frame size is 2047 bytes, on the AR934x it is 16383 bytes. Make the MTU setup code model specific, and use the correct bitmask for both models. Also change the value to the maximum. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39148
* ar71xx: ag71xx: calculate max frame len register value from the MTUGabor Juhos2013-12-201-3/+15
| | | | | | | | | | | | | | | Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init() and write the correct value into that from the ag71xx_open() and ag71xx_fast_reset() functions. Also recalculate the RX buffer size based on the actual maximum frame length value to optimize memory allocation. Additionaly, disallow to change the MTU value while the interface it running. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39147
* ar71xx: ag71xx: add ag71xx_max_frame_len() helperGabor Juhos2013-12-201-2/+8
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39146
* ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform dataGabor Juhos2013-12-203-2/+11
| | | | | | | | This will allow to use SoC specific values for both. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39145
* ar71xx: ag71xx: store descriptor packet length mask in ag71xx structGabor Juhos2013-12-202-7/+5
| | | | | | | | | | | | | | | The currently used bitmask is not correct for all SoCs. Introduce a new field in struct ag71xx and store the bitmask in that. Use the current value for now, it will be adjusted for each SoCs in further patches. Aslo use the new field directly in the ag71xx_rx_packets and ag71xx_hard_start_xmit() functions and remove the ag71xx_desc_pktlen() helper. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39144
* handle new libs required for new kernelsImre Kaloz2013-12-201-0/+10
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39142
* don't fail if there are no dtbsImre Kaloz2013-12-201-3/+3
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39141
* ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450hFelix Fietkau2013-12-191-0/+24
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39139
* ath9k: merge another round of upstream (or -pending) fixes and cleanupsFelix Fietkau2013-12-1917-170/+2799
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39138
* imx6: refresh patchesLuka Perkov2013-12-198-17/+15
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39135
* kernel: backport upstream inet fixLuka Perkov2013-12-191-0/+54
| | | | | | | | | Without it in some occasions oops is shown on network restart. Problem was noticed on imx6 targed. Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39134
* imx6: proper fix for io-remapLuka Perkov2013-12-194-210/+118
| | | | | | | | | The previous patch was not the proper fix for PCI devices that require io resources. The new patch is the proper fix backported from mainline. Signed-off-by: Tim Harvey <tharvey@gateworks.com> SVN-Revision: 39133
* procd: fix service file trackingJo-Philipp Wich2013-12-181-2/+2
| | | | | | | | | | | | | | | The instance_config_move() function in the procd instance managing code is missing a blobmsg_list_move() call to update the tracked file items with the newly calculated checksums in case of a file change. Without that change, services are always reloaded after the first change to a tracked file regardless of whether there are any subsequent changes or not. Add a missing instance of blobmsg_list_free() as well. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39132
* netifd: add reload trigger for /etc/config/wireless as wellJo-Philipp Wich2013-12-181-1/+4
| | | | SVN-Revision: 39131
* ar71xx: enable images for WD My Net N750Gabor Juhos2013-12-172-0/+10
| | | | | | | | | | | | | | Now that the switch works correctly we can enable the images for this board. Flashing from the factory firmware, the factory failsafe loader and sysupgrade was tested successfully. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4617/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39130
* ar71xx: fix WD My Net N750 switch led cfgGabor Juhos2013-12-171-4/+4
| | | | | | | | | | | Now that the switch is working correctly I had the chance to actually test the LED config. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4616/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39129
* ar71xx: implement switch fix for WD My Net N750Gabor Juhos2013-12-171-0/+19
| | | | | | | | | | | | | | | The bootloader on the WD My Net N750 disables the ports on it's internal AR8327N switch by powering them down. The stock firmware then brings the ports back up again by starting the auto negotiation process on each port. This fix implements just that. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4615/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39128
* ar71xx: implement callback in mdio resetGabor Juhos2013-12-172-0/+5
| | | | | | | | | | | This enables us to add fixups to the board specific code for boards that require special treatment of PHYs on mdio bus reset. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> http://patchwork.openwrt.org/patch/4614/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39127
* ar71xx: make ag71xx_mdio_platform_data visibleGabor Juhos2013-12-172-2/+4
| | | | | | | | | | | This enables us to modify the ag71xx_mdio_platform_data from within the board support files. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4613/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39126
* busybox: add back support for top-level menuconfig based config overrides ↵Felix Fietkau2013-12-173-6/+7
| | | | | | | | (can be used by custom packages to alter the config) Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39125
* gpio-button-hotplug: fix crash on removeJonas Gorski2013-12-171-1/+1
| | | | | | | | | | Don't call gpio_keys_remove recursively. Setting the platform data to NULL triggered an oops on the second iteration, so there was no infinate loop. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 39124
* busybox: restore init scriptsJo-Philipp Wich2013-12-171-8/+3
| | | | | | | | | | Since the removal of the busybox menuconfig entries, the init scripts for cron, telnet and ntp are not packaged anymore. Unconditionally ship them from now on. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39123
* firewall: fix handling of tcp_ecn parameterJo-Philipp Wich2013-12-171-2/+2
| | | | | | | | | | | The firewall3 implementation as well as the shell implementation predating it used to process the tcp_ecnoption as boolean while it actually is an integer. Change the code to parse tcp_ecn as integer. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39122
* ar71xx: ag71xx: compute the RX buffer size from the maximum frame sizeGabor Juhos2013-12-172-3/+1
| | | | | | | | | | | | | | | | Currently, the AG71XX_RX_PKT_SIZE value limits the received frame size to 1514/1516 bytes with/without a VLAN header respectively. However the hardware limit is controlled by the value the AG71XX_REG_MAC_MFL register which contains the value of the max_frame_len field. Compute the RX buffer size from the max_frame_len field to get rid of the 1514/1516 byte limitation. Also remove the unused AG71XX_RX_PKT_SIZE definition. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39121
* ar71xx: ag71xx: store RX buffer size in the ag71xx structGabor Juhos2013-12-172-6/+8
| | | | | | | | This allows to change the value dynamically. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39120
* iproute2: reduce .ipk package size from ~100k down to ~60kFelix Fietkau2013-12-172-1/+121
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39119
* busybox: disable module utils, kmodloader provides themFelix Fietkau2013-12-171-6/+7
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39118
* ar71xx: ag71xx: store maximum frame length in the ag71xx structGabor Juhos2013-12-172-2/+8
| | | | | | | | | This will allow to use different values for the different SoCs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39117
* ar71xx: ag71xx: use mdio bus name in ar7240_probe messagesGabor Juhos2013-12-171-4/+4
| | | | | | | | | | | | | | | The ar7240_probe function uses the network device name in the kernel log messages, however the name is not yet initialized when the ar7240_probe function is called. Use the mdio bus name in the messages to avoid ugly log lines like the following one: eth%d: Found an AR7240/AR9330 built-in switch Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39116
* ag71xx: ag71xx: use device name for debugfs entryGabor Juhos2013-12-171-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | The ag71xx debugfs code uses the network device name for the device specific debugfs directory. Since r38689 'ar71xx: ag71xx: fix a race involving netdev registration' the debugfs initialization happens before the ethernet device gets registered and the network device name contains 'eth%d' at this point. If the board setup code registers multiple ag71xx devices, the debugfs code tries to create the device specific dir with the same name which causes an error like this: eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] ag71xx: probe of ag71xx.0 failed with error -12 Use the device name for the debugfs directory to avoid the collisions. Also add an error message and change the return code if the debugfs_create_dir call fails. Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39115
* busybox: fix typo in Config.in (#14628)Felix Fietkau2013-12-171-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 39114
* imx6: ventana: add canbus utilsLuka Perkov2013-12-171-1/+2
| | | | | | | | | Some of the Gateworks Ventana boards have CAN bus support, therefore we will install the userspace utils. Signed-off-by: Tim Harvey <tharvey@gateworks.com> SVN-Revision: 39113
* imx6: ventana: add default kernel modules for GSCLuka Perkov2013-12-171-0/+1
| | | | | | | | | | | | | All Gateworks Ventana boards have a Gateworks System Controller which emulates the following: - ds1672 RTC - pca953x GPIO expander - hardware monitor - at24 eeprom Signed-off-by: Tim Harvey <tharvey@gateworks.com> SVN-Revision: 39112
* imx6: add rtc feature supportLuka Perkov2013-12-173-1/+8
| | | | | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39111
* kernel: add rtc-ds1672 module supportLuka Perkov2013-12-171-0/+17
| | | | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com> SVN-Revision: 39110
* imx6: drop upstreamed patchLuka Perkov2013-12-171-25/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39109
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-16 14:58:09 +0000