aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* package: fix cmake packages build with ninjaRosen Penev2021-06-125-4/+5
| | | | | | | | += is needed for CMAKE_OPTIONS. mt76 needs Ninja disabled as the kernel stuff uses normal make. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* build: add ninja build tool and make it available for cmakeFelix Fietkau2021-06-125-1/+2359
| | | | | | | | | | | | ninja is faster at building cmake packages than make, and according to reports also more reliable at handling parallel builds This commit includes a patch that adds GNU make jobserver support, in order to allow more precise control over the number of parallel tasks Enable parallel build by default for packages using ninja Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Rosen Penev <rosenp@gmail.com>
* u-boot: support verbose buildFelix Fietkau2021-06-121-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add support for 802.3 encap offload with software rate controlFelix Fietkau2021-06-122-0/+158
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: improve rate control performanceFelix Fietkau2021-06-121-0/+114
| | | | | | Call rate control handler after intermediate queueuing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* rockchip: add NanoPi R4S supportTianling Shen2021-06-1012-2/+452
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3399 ARM64 (6 cores) 4GB LPDDR4 RAM 2x 1000 Base-T 3 LEDs (LAN / WAN / SYS) 1 Button (Reset) Micro-SD slot 2x USB 3.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card using dd. ===================================== NOTICE FOR USERS WHO USE 1GB VERSION: BY NOW IT IS NOT SUPPORTED ==================================== [initialed target] Co-developed-by: Marty Jones <mj8263788@gmail.com> Signed-off-by: Marty Jones <mj8263788@gmail.com> [fixed bootscript] Co-developed-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com> Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: add NanoPi R4S supportTianling Shen2021-06-102-0/+301
| | | | | | Add support for the FriendlyARM NanoPi R4S. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* x86: add upgrade support to diag.shChris Blake2021-06-101-0/+4
| | | | | | | | | Similar to how this is done in the diag.sh found in the base-files package, we should blink our status LED (if we have one) during the upgrade process. This follows the same blink pattern as seen at ./package/base-files/files/etc/diag.sh#L36 Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* mac80211: rely on iwinfo for phy->path and path->phy lookupsFelix Fietkau2021-06-104-42/+3
| | | | | | This avoids inconsistencies from having multiple implementations do the same thing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* iwinfo: update to the latest versionFelix Fietkau2021-06-101-3/+3
| | | | | | | | | aa0e3c4bbe12 iwinfo: nl80211: add support for printing the device path for a phy dd6d6d2dec35 iwinfo: nl80211: use new path lookup function for nl80211_phy_idx_from_uci_path 268bb26d2e2a iwinfo: nl80211: support looking up phy by path=.. and macaddr=... c0414642fead iwinfo: nl80211: fix typo Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix LAN LED trigger assignment for Xiaomi Router 3 ProAdam Elyas2021-06-091-2/+2
| | | | | | | | | | | | The default trigger for the amber lights on lan1 and lan3 were mistakenly swapped after the device's migration to DSA. This caused activity on one port to trigger the amber light on the other port. Swapping their default trigger in the DTS file fixes that. Signed-off-by: Adam Elyas <adamelyas@outlook.com> [minor commit title adjustment, wrap commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: disable Jboot devices buildPawel Dembicki2021-06-091-0/+1
| | | | | | | At this moment kernel size in mt7620 snapshot builds is bigger than 2048k. It should be disabled by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: add kernel size for Jboot devicesPawel Dembicki2021-06-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since few months multiple users reported problems with various JBoot devices. [0][1][2][3] All of them was bricked. On my Lava LR-25G001 it freezes with current snapshot: CDW57CAM_003 Jboot B695 Giga Switch AR8327 init AR8327/AR8337 id ==> 0x1302 JRecovery Version R1.2 2014/04/01 18:25 SPI FLASH: MX25l12805d 16M . . (freeze) The kernel size is >2048k. I built current master with minimal config and it boots well: CDW57CAM_003 Jboot B695 Giga Switch AR8327 init AR8327/AR8337 id ==> 0x1302 JRecovery Version R1.2 2014/04/01 18:25 SPI FLASH: MX25l12805d 16M . ........................... Starting kernel @80000000... [ 0.000000] Linux version 5.4.124 Kernel size is <2048k. Jboot bootloader isn't open source, so it's impossible to find solution in code. It looks, that some buffer for kernel have 2MB size. To avoid bricked devices, this commit introduces 2048k limit kernel size for all jboot routers. [0] https://bugs.openwrt.org/index.php?do=details&task_id=3539 [1] https://eko.one.pl/forum/viewtopic.php?pid=254344 [2] https://eko.one.pl/forum/viewtopic.php?id=20930 [3] https://eko.one.pl/forum/viewtopic.php?pid=241376#p241376 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [remove Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix Ethernet random MAC address for HILINK HLK-7628NLiu Yu2021-06-092-4/+5
| | | | | | | | | | | | | | | | | | Set the ethernet address from flash. MAC addresses as verified by OEM firmware: use interface source 2g wlan0 factory 0x04 (label) LAN eth0.1 factory 0x28 (label+1) WAN eth0.2 factory 0x2e (label+2) Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N") Signed-off-by: Liu Yu <f78fk@live.com> [drop old MAC address setup from 02_network, cut out state_default changes, face-lift commit message, add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* toolchain/gdb: fix broken non-python buildFelix Fietkau2021-06-091-1/+1
| | | | | | | Append configure args instead of overwriting them Fixes: 74417f8b3a80 ("toolchain: gdb: Add optional python support") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: fix build for devices without initramfsDavid Bauer2021-06-081-1/+1
| | | | | | | | | Don't attempt to copy initramfs images for devices which do not output an initramfs image. This was breaking builds for mpc85xx-p1010 since mid-march. Signed-off-by: David Bauer <mail@david-bauer.net>
* scripts/feeds: generate index after all feeds are updatedKarel Kočí2021-06-071-44/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This separates index update from feed update. The result is that all requested feeds are first updated and only then indexed. The reason for this change is to prevent errors being reported and potentially invalid index being generated thanks to cross feeds dependency. The feeds script pulls in default all feeds as they come and on install prefers packages from first feeds (unless special feed is requested). Thus order of feeds in some way specifies preferences. This is handy for downstream distributions as they can simply override any package from upstream feeds by placing their feed before them. This removes need to patch or fork upstream feeds. The problem is that such feed most likely depends in some way also on subsequent feeds. The most likely feeds are 'packages' or 'luci'. The example would be Python package that needs 'python.mk' from 'packages' feed. Ordering custom feed after dependent feeds is sometimes just not possible because of preference requirement described before. The solution is to just first pull all feeds and generate indexes only after that. In the end this ensures that index is generated correctly at first try without any error. In terms of code this removes 'perform_update' argument from 'update_feed' as with index update removal the update is the only action performed in that subroutine. Thus this moves condition to 'update' subroutine. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* ramips: fix patch locationDavid Bauer2021-06-081-7/+7
| | | | | | | | | | | The patch for adding the config_aneg function for the Atheros AR8031/AR8033 PHY was formatted in a way it moved to different PHY models while refreshing patches on kernel updates. Move the diff directly below the PHY name so this won't happen in the future. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7620: enable autonegotiation for all portsGaspare Bruno2021-06-081-0/+1
| | | | | | | | | This enables autonegotiation for all ephy ports on probe. Some devices do not configure the ports, particularly port 4. Signed-off-by: Gaspare Bruno <gaspare@anlix.io> [replace magic values ; reword commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: make PHY initialization more descriptiveDavid Bauer2021-06-081-3/+4
| | | | | | | The basic mode control register of the ESW PHYs is modified in this codeblock. Use the respective macros to make this code more readable. Signed-off-by: David Bauer <mail@david-bauer.net>
* linux-firmware: update to 20210511Tomas Lara2021-06-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20201118..20210511 7685cf4 (HEAD, tag: 20210511) nvidia: Update Tegra194 XUSB firmware to v60.09 cf32752 nvidia: Update Tegra186 XUSB firmware to v55.18 cb8ca82 nvidia: Update Tegra210 XUSB firmware to v50.26 f99d6a1 linux-firmware: update firmware for mhdp8546 ecdfcf8 Merge branch 'adlp_dmc_firmware' of git://anongit.freedesktop.org/drm/drm-firmware into main 547b202 Merge https://github.com/suraj714/linux-firmware-venus into main 3d32f21 i915: Add ADL-P DMC Support 3f23f51 amdgpu: add new polaris 12 MC firmware a2565bb firmware: nvidia: Add VIC firmware for Tegra194 17ec2a5 qcom: add gpu firmwares for sc7280 b653cf4 Merge https://github.com/pkshih/linux-firmware into main 2a96c08 brcm: Add a link to enable khadas VIM2's WiFi ffc64a2 rtw89: 8852a: update fw to v0.13.8.0 3e3497c rtl_bt: Update RTL8852A BT USB firmware to 0xD9A8_7893 c7b11ed qcom: Add venus firmware files for VPU-2.0 2f4f0f8 rtw89: 8852a: update fw to v0.13.8.0 fa0efef linux-firmware: Update firmware file for Intel Bluetooth AX210 9be3daa linux-firmware: Update firmware file for Intel Bluetooth 9560 687d64a linux-firmware: Update firmware file for Intel Bluetooth 9260 a7f1249 linux-firmware: Update firmware file for Intel Bluetooth AX200 47650a0 linux-firmware: Update firmware file for Intel Bluetooth AX201 195ecf1 linux-firmware: Intel BT 7265: Fix Security Issues 4116d72 linux-firmware: Update firmware file for Intel Bluetooth 8265 ca83c73 qcom: update venus firmware files for v5.4 1334578 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main 16052e4 mrvl: prestera: Add Marvell Prestera Switchdev firmware 3.0 version bdf929d rtw88: 8822c: Update normal firmware to v9.9.9 0b558e8 brcm: add missing symlink for Pi Zero W NVRAM file cfa004c amdgpu: update arcturus firmware from 21.10 d5567c5 amdgpu: update navy flounder firmware from 21.10 ef5ea5d amdgpu: update sienna cichlid firmware from 21.10 f35700f amdgpu: update vega20 firmware from 21.10 1be98f1 amdgpu: update picasso firmware from 21.10 fee0497 amdgpu: update navi14 firmware from 21.10 15003b0 amdgpu: update green sardine firmware from 21.10 64555fb amdgpu: update vega12 firmware from 21.10 eb07276 amdgpu: update navi12 firmware from 21.10 e36c82a amdgpu: update vega10 firmware from 21.10 4a5eaa2 amdgpu: update renoir firmware from 21.10 65eb326 amdgpu: update navi10 firmware from 21.10 8bdca03 amdgpu: update raven2 firmware from 21.10 c9e44ca amdgpu: update raven firmware from 21.10 bc3e610 rtl_nic: add new firmware for RTL8153 and RTL8156 series 8528618 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware into main 940b7f4 cxgb4: Update firmware to revision 1.25.4.0 f66adc3 Merge branch 'main' of gitolite.kernel.org:/pub/scm/linux/kernel/git/maks/linux-firmware into main f350e91 Merge https://github.com/rjliao-qca/qca-btfw into main 9bc1bcc Merge https://github.com/Netronome/linux-firmware into main 2f30708 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2438 393f272 brcm: Link CM4's WiFi firmware with DMI machine name. 73144e0 linux-firmware: Update firmware file for Intel Bluetooth AX201 8ab7aba amdgpu: update navi14 smc firmware 4fe6e53 amdgpu: update navi10 SMC firmware c296849 QCA: Update Bluetooth firmware for QCA6174 d6a18e9 WHENCE: link to similar config file for rtl8821a support 6c419ae nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.14.A.6 af1ca28 amdgpu: add arcturus firmware 0dd245d Merge branch 'sm8250-new-fw' of https://github.com/lumag/linux-firmware into main 55cab07 rtl_bt: Add rtl8723bs_config-OBDA0623.bin symlink 2548d06 brcm: Add nvram for the Chuwi Hi8 (CWI509) tablet e45c137 brcm: Add nvram for the Predia Basic tablet d8fa0cf qcom: sm8250: update remoteproc firmware 84af0e0 qcom: update a650 firmware files 3f026a2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x59A_76A3 c82cb46 amdgpu: update sienna cichlid firmware for 20.50 24fe696 amdgpu: update vega20 firmware for 20.50 e05d197 amdgpu: update picasso firmware for 20.50 76d07cd amdgpu: update navi14 firmware for 20.50 b2fc037 amdgpu: update vega12 firmware for 20.50 25451a4 amdgpu: update navi12 firmware for 20.50 b938597 amdgpu: update vega10 firmware for 20.50 2542ba7 amdgpu: update renoir firmware for 20.50 b55d063 amdgpu: update navi10 firmware for 20.50 1a62f28 amdgpu: update raven2 firmware for 20.50 4df488f amdgpu: update raven firmware for 20.50 a29bdb2 amdgpu: add initial support for navy flounder 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 Signed-off-by: Tomas Lara <tl849670@gmail.com> [rebased; removed brcmfmac changes due to removed firmware] Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: backport at803x fixesDavid Bauer2021-06-0812-208/+361
| | | | | | | | | | As patches for the AR8031/AR8033 copper page selection were merged upstream, we can backport these patches. This also fixes a PHY capabilities detection issue on the Ubiquiti ER-X-SFP. Signed-off-by: David Bauer <mail@david-bauer.net>
* ethtool: update to version 5.12Robert Marko2021-06-081-2/+2
| | | | | | Update ethtool to newly released 5.12 version. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ugps: update to git HEADDaniel Golle2021-06-071-4/+4
| | | | | | | | 86ee86e nmea: parse $GPZDA sentences for date/time 8e12414 nmea: parse $GPGLL sentences for position 5e88403 ubus: display only available information Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: fix eth0 PLL registers on WD My Net Wi-Fi Range ExtenderJonathan A. Kollasch2021-06-071-2/+2
| | | | | | | | | | | This replaces the register bits for RGMII delay on the MAC side in favor of having the RGMII delay on the PHY side by setting the phy-mode property to rgmii-id (RGMII internal delay), which is supported by the at803x driver. Speed 1000 is fixed as a result, so now all ethernet speeds function. Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-by: Michael Pratt <mcpratt@pm.me>
* ath79: Support for Ubiquiti Rocket 5AC LiteNick Hainke2021-06-074-0/+49
| | | | | | | | | | | | | | | | | | | The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - Ethernet: 1x 10/100/1000 Mbps - WiFi 5 GHz: QCA988x - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI Installation: - Instructions for XC-type Ubiquiti: https://openwrt.org/toh/ubiquiti/common Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: add support for NEC Aterm WF1200CRINAGAKI Hiroshi2021-06-065-5/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on QCA9561. Specification: - SoC : Qualcomm Atheros QCA9561 - RAM : DDR2 128 MiB (W971GG6SB-25) - Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9561 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100 Mbps - Switch : QCA9561 (SoC) - LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from "JP1" marking - 115200n8 - Power : 12 VDC, 0.9 A Flash instruction using factory image (stock: < v1.3.2): 1. Boot WF1200CR normally with "Router" mode 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Alternate flash instruction using initramfs image (stock: >= v1.3.2): 1. Prepare the TFTP server with the IP address 192.168.1.10 and place the OpenWrt initramfs image to the TFTP directory with the name "0101A8C0.img" 2. Connect serial console to WF1200CR 3. Boot WF1200CR and interrupt with any key after the message "Hit any key to stop autoboot: 2", the U-Boot starts telnetd after the message "starting telnetd server from server 192.168.1.1" 4. login the telnet (address: 192.168.1.1) 5. Perform the following commands to modify "bootcmd" variable temporary and check the value (to ignore the limitation of available commands, "tp; " command at the first is required as dummy, and the output of "printenv" is printed on the serial console) tp; set bootcmd 'set autostart yes; tftpboot' tp; printenv 6. Save the modified variable with the following command and reset device tp; saveenv tp; reset 7. The U-Boot downloads initramfs image from TFTP server and boots it 8. On initramfs image, download the sysupgrade image to the device and perform the following commands to erase stock firmware and sysupgrade mtd erase firmware sysupgrade <sysupgrade image> 9. After the rebooting by completion of sysupgrade, start U-Boot telnetd and login with the same way above (3, 4) 10. Perform the following commands to reset "bootcmd" variable to the default and reset the device tp; run seattle tp; reset (the contents of "seattle": setenv bootcmd 'bootm 0x9f070040' && saveenv) 11. Wait booting-up the device Known issues: - the following 6x LEDs are connected to the gpio controller on QCA9888 chip and the implementation of control via the controller is missing in ath10k/ath10k-ct - "ACTIVE" (Red/Green) - "2.4GHz" (Red/Green) - "5GHz" (Red/Green) Note: - after the version v1.3.2 of stock firmware, "offline update" by uploading image by user is deleted and the factory image cannot be used - the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN and the configuration is required on OpenWrt - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output - pinmux: set GPIO 14/19 as switch-controlled LEDs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Add support for SERCOMM NA502Andreas Böhler2021-06-064-0/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: do not quote compatible in shell scriptsAdrian Schmutzler2021-06-063-21/+21
| | | | | | | The compatible is a literal string without any problematic characters, so there is no reason to quote it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uboot-kirkwood: refresh patchesAdrian Schmutzler2021-06-0610-45/+35
| | | | | | | | This is only cosmetic, but the next one adding a patch here would have to do it anyway, and thus will get a smaller diff for review now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-068-2/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for the Wavlink WL-WN579X3Ben Gainey2021-06-064-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | About the device ---------------- SoC: MediaTek MT7620a @ 580MHz RAM: 64M FLASH: 8MB WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 2x (RTL8211F) BTN: - WPS - Reset - Router/Repeater/AP (3-way slide-switch) LED: - WPS (blue) - 3-segment Wifi signal representation (blue) - WiFi (blue) - WAN (blue) - LAN (blue) - Power (blue) UART: UART is present as Pads with through-holes on the PCB. They are located next to the reset button and are labelled Vcc/TX/RX/GND as appropriate. Use 3.3V, 57600-8N1. Installation ------------ Using the webcmd interface -------------------------- Warning: Do not update to the latest Wavlink firmware (version 20201201) as this removes the webcmd console and you will need to use the serial port instead. You will need to have built uboot/sqauashfs image for this device, and you will need to provide an HTTP service where the image can be downloaded from that is accessible by the device. You cannot use the device manufacturers firmware upgrade interface as it rejects the OpenWrt image. 1. Log into the device's admin portal. This is necessary to authenticate you as a user in order to be able to access the webcmd interface. 2. Navigate to http://<device-ip>/webcmd.shtml - you can access the console directly through this page, or you may wish to launch the installed `telnetd` and use telnet instead. * Using telnet is recommended since it provides a more convenient shell interface that the web form. * Launch telnetd from the form with the command `telnetd`. * Check the port that telnetd is running on using `netstat -antp|grep telnetd`, it is likely to be 2323. * Connect to the target using `telnet`. The username should be `admin2860`, and the password is your admin password. 3. On the target use `curl` to download the image. e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\ wavlink_wl-wn579x3-squashfs-sysupgrade.bin`. Check the hash using `md5sum`. 4. Use the mtd_write command to flash the image. * The flash partition should be mtd4, but check /sys/class/mtd/mtd4/name first. The partition should be called 'Kernel'. * To flash use the following command: `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>` Where mtd<n> is the Kernel partition, and <image-file> is the OpenWrt image previously downloaded. * The command above will erase, flash and then reboot the device. Once it reboots it will be running OpenWrt. Connect via ssh to the device at 192.168.1.1 on the LAN port. The WAN port will be configured via DHCP. Using the serial port --------------------- The device uses uboot like many other MT7260a based boards. To use this interface, you will need to connect to the serial interface, and provide a TFTP server. At boot follow the bootloader menu and select option 2 to erase/flash the image. Provide the address and filename details for the tftp server. The bootloader will do the rest. Once the image is flashed, the board will boot into OpenWrt. The console is available over the serial port. Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
* ath79: add support for Devolo dLAN pro 1200+ WiFi acFelix Matouschek2021-06-068-166/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Devolo dLAN pro 1200+ WiFi ac. This device is a plc wifi AC2400 router/extender with 2 Ethernet ports, has a QCA7500 PLC and uses the HomePlug AV2 standard. Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI. Therefore it uses the same dts, which was moved to a dtsi to be included by both boards. This is a board that was previously included in the ar71xx tree. Hardware: SoC: AR9344 CPU: 560 MHz Flash: 16 MiB (W25Q128JVSIQ) RAM: 128 MiB DDR2 Ethernet: 2xLAN 10/100/1000 PLC: QCA75000 (Qualcomm HPAV2) PLC Uplink: 1Gbps MIMO PLC Link: RGMII 1Gbps (WAN) WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9882-BR4A 5GHz 802.11ac Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2 Button: 3x Buttons (Reset, wifi and plc) LED: 3x Leds (wifi, plc white, plc red) GPIO Switch: 11-PLC Pairing (Active Low) 13-PLC Enable 21-WLAN power MACs Details verified with the stock firmware: Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002 Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006 Ethernet &ethernet *:4e = 2.4 GHz + 2 PLC uplink --- *:4f = 2.4 GHz + 3 Label MAC address is from PLC uplink The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd party firmware which is not available from standard OpenWrt package feeds. There is a package feed on github which you must add to OpenWrt buildroot so you can build a firmware image which supports the plc interface. See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and added compatibility for OpenWrt 21.02) Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.100 2. Download the sysupgrade image and rename it to uploadfile 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Allow 1-2 minutes for the first boot. Signed-off-by: Felix Matouschek <felix@matouschek.org> [add "plus" to compatible and device name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: Update to backports-5.10.42Hauke Mehrtens2021-06-0634-2349/+63
| | | | | | | | | | | | The removed patches were integrated upstream. The brcmf_driver_work workqueue was removed in brcmfmac with kernel 5.10.42, the asynchronous call was covered to a synchronous call. There is no need to wait any more. This part was removed manually from this patch: brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mt76: update to the latest versionFelix Fietkau2021-06-061-4/+4
| | | | | | | | Add mt7915e dependency on kmod-thermal 22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered Signed-off-by: Felix Fietkau <nbd@nbd.name>
* linux-firmware: update to version 20210315 and trim down broadcom FWJosef Schlehofer2021-06-063-34/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In there linux-firmware repository located in kernel, there were removed old broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability (CVE-2019-15126), because Cypress released new versions and superseded by it. In OpenWrt, there is Makefile for cypress-firmware, which already provides the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio provides brcmfmac-firmware-43455-sdio [2]. Changelog between 2020118 and 20210315: 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 [1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c [2] https://github.com/openwrt/openwrt/blob/eeda8652f1655d4f9c11e9c9f51ddcd3377d119a/package/firmware/cypress-firmware/Makefile#L124 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* x86: add Roqos Core RC10 ethernet interfacesTomasz Maciej Nowak2021-06-061-0/+3
| | | | | | | | | | | | | | | | | | | eth0 -> single NIC (i211at) eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U) Notes UART is exposed on J4 connector, pinout starting from pin marked 1: 1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC? baud: 115200, parity: none, flow control: none The board is setup by coreboot with UEFI. To enter setup screen hold ESC key on boot. The 5-LED multicolor matrix is attached on first I2C device named "Synopsys DesignWare I2C adapter" at address 0x60. Controlling values are stored in /opt/roqos/etc/rcLED.conf of original firmware. Remember to backup the original firmware, there are no downloadable copies. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* kernel: package Synopsys Designware PCI to I2C controllerTomasz Maciej Nowak2021-06-061-0/+29
| | | | | | This is present on Roqos Core RC10 and needed to control LED matrix. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: armada-37xx: remove ethernet alias patchTomasz Maciej Nowak2021-06-064-20/+0
| | | | | | | | | This patch has been added with initial support for ESPRESSObin board and mistakenly it affects all boards with this SoC. Drop this patch since the aliases are now in upstream dts for ESPRESSObin. If any boards are relying on this, please add the respective alias to that board dts. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add uboot-envtools to default packagesTomasz Maciej Nowak2021-06-062-17/+14
| | | | | | | | | | | | | | | | | | | When support for Luma WRTQ-329ACN was added, the instructions for flashing this device include using tools from uboot-envtools package. Unfortunately the OpenWrt buildroot system omits packages from DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE, CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In result the official images are without tools mentioned in the instruction. The workoround for the fashing would be installing uboot-envtools when booted with initramfs image, but not always the access to internet is available. The other method would be to issue the necesary command in U-Boot environment but some serial terminals default configuration don't work well with pasting lines longer than 80 chars. Therefore add uboot-envtools to default packages, which adds really small flash footprint to rootfs, where increased size usually is not an issue. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tools/isl: bump to 0.24Rui Salvaterra2021-06-061-2/+2
| | | | | | Tested with Graphite and -floop-nest-optimize, without issues. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* toolchain: gdb: Add optional python supportHauke Mehrtens2021-06-062-1/+18
| | | | | | | | | | | | | Compile gdb with python support optionally. To use the Python support in gdb some extra python files are needed, install them too. While at it also install other shared files which we did not install before. If gdb is built without Python support the python folder does not exists. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* ipq806x: fix LAN and WAN port assignments on TP-Link AD7200Alex Henrie2021-06-061-1/+4
| | | | | | | | LAN port 4 was swapped with the WAN port and the remaining three LAN ports were numbered in reverse order from their labels on the case. Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200") Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
* layerscape: armv8_64b: enable CONFIG_ARM_PSCI_CPUIDLEMartin Schiller2021-06-061-0/+1
| | | | | | | | Enable PSCI firmware based CPUidle driver. PSCI firmware is the standard power management control for all ARM64 based platforms. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* kernel: usb: add kmod-usb-gadget-ncmKuan-Yi Li2021-06-061-0/+17
| | | | | | | Add kernel module package for USB Network Control Model (NCM) Gadget support. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* x86: kernel: enable Fusion-MPT SAS driverMark Carroll2021-06-062-0/+2
| | | | | | | Compile in MPT SAS driver required to mount rootfs on some VMWare systems (e.g. required for 1&1 IONOS). Signed-off-by: Mark Carroll <git@markcarroll.net>
* ath10k-ct: update to latest versionMichael Yartys2021-06-064-45/+8
| | | | | | | | | | | | | | | | Changelog: - ath10k-ct: Add security fixes. - ath10k-ct: Add 5.12 kernel version. - ath10k-ct: Fix the beacon/mcast/bcast override issue - ath10k-ct 5.7: Fix setting mcast/bcast/beacon rate from debugfs. - ath10k-ct: Add 5.11 driver. Delete upstreamed patch and refresh the rest. Also, use the opportunity to set PKG_RELEASE to $(AUTORELEASE). Runtime-tested on ipq806x (Netgear R7800). Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
* kernel: bump 5.4 to 5.4.124John Audia2021-06-0645-167/+168
| | | | | | | | | | | | | | | | | Manually rebased: generic/hack-5.4/662-remove_pfifo_fast.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [manual changes to ramips/patches-5.10/835-asoc-add-mt7620-support.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.10 to 5.10.42Rui Salvaterra2021-06-0654-190/+148
| | | | | | | | | | Deleted (reverse-appliable): generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch Manually refreshed: ramips/patches-5.10/835-asoc-add-mt7620-support.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-0512-49/+49
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>