aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* layerscape: add ls1012afrdm device supportYangbo Lu2017-11-106-5/+88
| | | | | | | | The QorIQ FRDM-LS1012A Board is an ultra-low-cost development platform for QorIQ LS1012A Series Network Processors built on ARM Cortex-A53 processor. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: enlarge ext4 rootfs size to 30MBYangbo Lu2017-11-105-8/+8
| | | | | | This patch is to enlarge ext4 rootfs size to 30MB. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add ppa firmware packageYangbo Lu2017-11-102-10/+128
| | | | | | | | | | | | | | This patch is to add PPA (The Primary Protected Application) package and also enable it for all layerscape devices. LSDK github provides ppa source code git tree, but it only could be compiled with 64-bit toolchain. For 32-bit devices, there was no method to use it. https://github.com/qoriq-open-source/ppa-generic This patch is to directly use a private ppa binary tree for both 32-bit and 64-bit devices. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support LSDK ppfeYangbo Lu2017-11-103-64/+36
| | | | | | | | This patch is to use ppfe git tree on LSDK github instead of private git tree, and support the latest ppfe on ls1012ardb. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix ls1046ardb 32-bit call traceYangbo Lu2017-11-102-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enabled CONFIG_ARCH_DMA_ADDR_T_64BIT in kernel to resolve below call trace when ls1046ardb 32-bit started up kernel. [ 0.142141] Bman ver:0a02,02,01 [ 0.145326] ------------[ cut here ]------------ [ 0.149969] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:303 __arm_ioremap_pfn_caller+0x1ac/0x1d8 [ 0.159152] Modules linked in: [ 0.162216] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.51-g9c76e024 #2 [ 0.169036] Hardware name: Generic DT based system [ 0.173853] [<c02236a4>] (unwind_backtrace) from [<c021ed94>] (show_stack+0x10/0x14) [ 0.181638] [<c021ed94>] (show_stack) from [<c04d2d38>] (dump_stack+0x98/0xac) [ 0.188899] [<c04d2d38>] (dump_stack) from [<c0245bcc>] (__warn+0xe4/0x100) [ 0.195896] [<c0245bcc>] (__warn) from [<c0245c98>] (warn_slowpath_null+0x20/0x28) [ 0.203504] [<c0245c98>] (warn_slowpath_null) from [<c0229e24>] (__arm_ioremap_pfn_caller+0x1ac/0x1d8) [ 0.212861] [<c0229e24>] (__arm_ioremap_pfn_caller) from [<c0229f0c>] (ioremap_cache+0x20/0x28) [ 0.221608] [<c0229f0c>] (ioremap_cache) from [<c105e390>] (parse_mem_property.part.3+0x18/0x50) [ 0.230441] [<c105e390>] (parse_mem_property.part.3) from [<c105e6dc>] (qman_init_early+0x314/0x334) [ 0.239623] [<c105e6dc>] (qman_init_early) from [<c0201a24>] (do_one_initcall+0xb4/0x168) [ 0.247844] [<c0201a24>] (do_one_initcall) from [<c1000e84>] (kernel_init_freeable+0x1d8/0x280) [ 0.256590] [<c1000e84>] (kernel_init_freeable) from [<c0adbcfc>] (kernel_init+0x8/0x114) [ 0.264812] [<c0adbcfc>] (kernel_init) from [<c021bb28>] (ret_from_fork+0x14/0x2c) [ 0.272423] ---[ end trace 39aaeef329e2a0a2 ]--- [ 0.277058] qman-fqd addr 0xfb000000 size 0x800000 Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update config-4.9Yangbo Lu2017-11-102-4/+12
| | | | | | | | Some new options were introduced by kernel patches. And some options should be removed/added. The config-4.9 should be updated accordingly. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update kernel patchesYangbo Lu2017-11-1013-1411/+14969
| | | | | | | Updated kernel patches to align layerscape kernel with latest LSDK linux (LSDK-17.09-update-103017-V4.9 tag). Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: stop pfe before starting up kernelYangbo Lu2017-11-102-3/+3
| | | | | | | For ls1012ardb, pfe should be stopped before starting up kernel. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update u-boot to LSDK-1709-update-103017 tagYangbo Lu2017-11-102-4/+4
| | | | | | Updated u-boot to LSDK-1709-update-103017 tag. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: use 1GHz CPU fequency for ls1012ardbYangbo Lu2017-11-101-1/+1
| | | | | | Used 1GHz CPU fequency for ls1012ardb instead of 800MHz. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update rcw to LSDK-17.09-update-103017 tagYangbo Lu2017-11-101-2/+2
| | | | | | Updated rcw to LSDK-17.09-update-103017 tag. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support LEDE boot for ls1088ardb/ls2088ardbYangbo Lu2017-11-102-0/+112
| | | | | | | Added u-boot patches to support LEDE boot for ls1088ardb and ls2088ardb. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support all-in-one firmware for ls1088ardb/ls2088ardbYangbo Lu2017-11-103-10/+58
| | | | | | | Suppport all-in-one firmware for ls1088ardb/ls2088ardb by integrating u-boot/rcw/mc/dpl/restool. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: remove default profileYangbo Lu2017-11-102-36/+0
| | | | | | | | | | Default profile had to enable many packages for all devices support. This made these packages still enabled when built for single device. This patch is to remove default profile. For multiple devices build, it's proper to build with multiple devices profile. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add restool packageYangbo Lu2017-11-1013-0/+794
| | | | | | | | restool is a user space application providing the ability to dynamically create and manage Layerscape DPAA2 containers and objects from Linux. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add dpl firmware packageYangbo Lu2017-11-101-0/+58
| | | | | | | This patch is to add data path layout files for the second generation Data Path Acceleration Architecture. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add mc firmware packageYangbo Lu2017-11-101-0/+57
| | | | | | | | This patch is to add package support for Management Complex Firmware for the second generation Data Path Acceleration Architecture. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: move fman/rcw/ppfe packages to layerscape/Yangbo Lu2017-11-104-0/+0
| | | | | | | This patch is to create a layerscape directory for all firmware packages of layerscape. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: clean up kernel patchesYangbo Lu2017-11-108-538/+538
| | | | | | | | | | | | | | | A previous patch disaggregated kernel patch 601 intending to reverse the ndo_get_stats64 change, but it also dropped many other changes without a reason. This caused build issue for layerscape. This patch is to fix that with below steps. 1. Reversed patch "1c4415a layerscape: reverse changes to ndo_get_stats64", but kept kernel patch 701 which was a proper fix. 2. Reversed the ndo_get_stats64 change in kernel patch 601. 3. Renamed patch 601 (net patch) to 202 (core-linux patch). Maybe it's more proper. Fixes: 1c4415a679f9 ("layerscape: reverse changes to ndo_get_stats64") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* brcm47xx: fix switch port mapping on Asus RT-N16Tim Thorpe2017-11-101-1/+1
| | | | | | | On the Asus RT-N16, the ports are not mapped the in the same way as the RT-N12. It is, however, the same as the Linksys E3000v1. Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
* ar71xx: fix regression in 74x164 initialization with 4.9Felix Fietkau2017-11-101-10/+12
| | | | | | | | | The memcpy of the init data relies on chip->registers to be initialized, which only happens later in the code. Move this initialization further down to make it work. This was breaking PCIe/USB on some MikroTik RouterBoard devices. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* rpcd: update to the latest version from 2017-11-09Rafał Miłecki2017-11-091-3/+3
| | | | | | 9a8640183c031 plugin: use RTLD_LOCAL instead of RTLD_GLOBAL when loading library Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: fix generating dtb with / in DEVICE_DTSFelix Fietkau2017-11-091-3/+4
| | | | | | Fixes layerscape build error Signed-off-by: Felix Fietkau <nbd@nbd.name>
* toolchain/musl: update to version 1.1.18Felix Fietkau2017-11-092-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/coreutils: install readlinkFelix Fietkau2017-11-091-2/+2
| | | | | | Parts of the build system use non-portable invocation of readlink Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: fix getting gid from group_add_nextYousong Zhou2017-11-092-8/+7
| | | | | | | | | | | | Shell function return code only has range [0, 255]. Other values will be truncated, e.g. return 65536 will have the same effect as return 0 While at it, drop other "return $rc" where rc will almost always take value 0 and whose value current callers actually do not check Fixes FS#988 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* lantiq: add missing macaddr retrieval for Netgear DGN3500Daniel Gimpelevich2017-11-081-0/+2
| | | | | | | The MAC addresses were not being set for LAN and WAN. This will now use the same MAC mechanism as the rest of the target. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ramips: add support for TP-Link TL-WR840N v5Robert Marko2017-11-087-1/+139
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 1x LED (GPIO-controlled), 1x button * LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Orange LED is registered so you can later use it for your own purposes. Flash instruction: Unlike TL-WR840N v4 flashing through WEB UI works in v5. 1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image. 2. Go to 192.168.0.1 3. Flash the sysupgrade image through Firmware upgrade section of WEB UI. 4. Wait until green LED stops flashing and use the router. Notes: TFTP recovery is broken since TP-Link reused bootloader code for v4 and that does not take into account only 4 MB of flash and bricks the device. So do not use TFTP Recovery or you will have to rewrite SPI flash. They fixed it in later GPL code,but it is unknown which version of bootloader you have. After manually compiling and flashing bootloader from GPL sources TFTP recovery works properly. Signed-off-by: Robert Marko <robimarko@gmail.com>
* functions.sh: fix default_postinst functionMarko Ratkaj2017-11-081-1/+1
| | | | | | | | | | | | | | | | | | When we run "opkg install" on a package that installs an uci-defaults script, functions.sh will fail to evaluate that script in its default_postinst function. This happens because there is no "./" present and it searches for the file in paths specified by the PATH variable. This would work on bash, but it will not work on ash and some other shells like sh, zsh. This applys to the ". filename" directive used in this case. This patch will make the path relative to the /etc/uci-defaults directory. Fixes: FS#1021 Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* generic: make mtdsplit-tplink.c honor rootfs offsetThibaut VARÈNE2017-11-081-6/+6
| | | | | | | | | | | | | | | | | | | | The splitter ignored the rootfs offset from the header, probably because until c1e6e61 it was invalid. This patch fixes the splitter to use the now correct header data. Regarding target/linux/ar71xx/files/drivers/mtd/tplinkpart.c, this particular splitter "falls back" to the correct rootfs offset reading and as such it doesn't need to be updated, although it will report a kernel partition length that can be larger than the actual length as it assumes that partition fills the entire segment up to the rootfs partition. Tested-by: Mathias Kresin <dev@kresin.me> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Henryk Heisig <hyniu@o2.pl> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* tools/firmware-utils: mktplinkfw* fix rootfs offsetThibaut VARÈNE2017-11-083-12/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With '-a' specified on the command line, the current code: - computes an aligned _kernel length_ instead of an aligned _rootfs offset_. - does not update the rootfs offset after computing the new kernel length, and instead retains the layout default. When the kernel length exceeds the available space left with this fixed offset, the resulting image header contains invalid data, with the recorded rootfs offset overlapping the kernel area. This patch ensures that rootfs offset is correctly computed and reflected in the final image. Furthermore, the build_fw() function special cases the rootfs_align option because of the above invalid logic. This is also fixed and the computed (or command-line provided, or layout-provided) rootfs_ofs value is used in all cases. There seems to be no valid reason to extend the kernel length beyond the actual length of the kernel itself (OFW images don't do it) so this part of the existing behavior is dropped. Example image before the patch: Kernel data offset : 0x00000200 / 512 bytes Kernel data length : 0x00158438 / 1410104 bytes Kernel load address : 0x00000080 Kernel entry point : 0x00000080 Rootfs data offset : 0x00140000 / 1310720 bytes Rootfs data length : 0x001e4f7e / 1986430 bytes Example image after the patch: Kernel data offset : 0x00000200 / 512 bytes Kernel data length : 0x001583fe / 1410046 bytes Kernel load address : 0x00000080 Kernel entry point : 0x00000080 Rootfs data offset : 0x00158600 / 1410560 bytes Rootfs data length : 0x001e4e22 / 1986082 bytes Tested-by: Mathias Kresin <dev@kresin.me> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Henryk Heisig <hyniu@o2.pl> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ltq-ptm: add missing depency to ltq-?dsl-*-meiJonas Gorski2017-11-071-0/+5
| | | | | | | Add the required dependency to the mei driver as cought by the depenceny checker. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ltq-atm: fix dependency for xrx200Jonas Gorski2017-11-071-1/+1
| | | | | | | Ad the missing dependency for the xrx200 variant, which depends on the vdsl mei driver. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ltq-adsl-mei: use the same file name for all variantJonas Gorski2017-11-073-8/+4
| | | | | | | | | | | Due to limitations in the symvers treatment and the mei drivers exporting the same funtions, modpost might use the wrong mei driver to link against. Work around this by renaming them all to the same name, making it always the "right" module name even if the wrong file was used. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* partially revert "mwlwifi: switch to AutoProbe"Jonas Gorski2017-11-071-1/+1
| | | | | | | | | | | | | Apearently we need to ensure mwlwifi loads before mwifiex on the WRT3200ACM, else mwifiex will claim the wifi. Fix this by reverting to AutoLoad, but keep the removal of mac80211 line. This partially reverts commit 471d5dc6e3c16a2bef9bde2b788b563a00357292. Fixes: 471d5dc6e3c1 ("mwlwifi: switch to AutoProbe") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* build: fix module symbol collection if build_dir is a symlinkJonas Gorski2017-11-071-1/+1
| | | | | | | | | | | | If PKG_BUILD_DIR contains symlinks, the generated Module.symvers will contain the resolved paths, not the virtual path with the symlink name. This breaks the filter for the module's own symbols, so to fix this ensure we also grep for the resolved path. Reported-by: Roman Yeryomin <roman@advem.lv> Tested-by: Roman Yeryomin <roman@advem.lv> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* firewall: update to latest git HEADHans Dedecker2017-11-071-3/+3
| | | | | | c430937 ubus: parse the firewall data within the service itself Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* include: kernel.mk: simplify module autoloadingJo-Philipp Wich2017-11-072-51/+25
| | | | | | | | | | | | | | | | | | Let the generic postinstall script invoke "kmodloader" when the just installed package contains any /etc/module.d/ entries. This allows us to skip the explicit "insert_module()" calls in the package postinstall. Due to the removed insert_module calls we do not need to assemble a complete list of modules per package anymore, which allows for vast simplification of the package generation code. While we're at it, also support specifying default parameters for modules using either the MODPARAM or MODPARAM.modulename variables in KernelPackage. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uhttpd: fix query string handlingJo-Philipp Wich2017-11-071-3/+3
| | | | | | | | | | Update to latest Git in order to fix potential memory corruption and invalid memory access when handling query strings in conjunction with active basic authentication. a235636 2017-11-04 file: fix query string handling Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* netifd: fix PKG_MIRROR_HASHDaniel Golle2017-11-071-1/+1
| | | | | | | | | commit fbde9ac7184 set an incorrect sha256sum which doesn't match the file http://sources.lede-project.org/netifd-2017-10-31-0f96606b.tar.xz or a locally packaged checkout (which resulted in a file identical with the one referenced by the URL above). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: remove default r1_key_holder generationYury Shvedov2017-11-061-2/+1
| | | | | | | | By default, hostapd assumes r1_key_holder equal to bssid. If LEDE configures the same static r1 key holder ID on two different APs (BSSes) the RRB exchanges fails behind them. Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
* netfilter, iptables: add optional CHECKSUM moduleDenis Osvald2017-11-063-0/+31
| | | | Signed-off-by: Denis Osvald <denis.osvald@sartura.hr>
* sunxi: add Orange Pi 2 supportZoltan HERPAI2017-11-062-0/+16
| | | | | | | | | | | | | - H3 @ 1.3 GHz - 1GiB DDR3 - 10/100Mbps Ethernet - Realtek RTL8189ETV wifi - 4 USB 2.0 Difference to the "Orange Pi Plus" is the lack of Gbit ethernet and lack of onboard flash. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT.Rosen Penev2017-11-063-7/+6
| | | | | | NAPI_POLL_WEIGHT was introduced in the kernel for exactly this purpose 5 years ago. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ixp4xx: drop the jumbo frame supportSergey Ryazanov2017-11-061-80/+0
| | | | | | | | | | | | | | | Current jumbo frame support code allocates rxbuffers of the maximum size supported by the hardware (~14KB). This happens at the device open time even if the configured MTU is lower (e.g. if it configured to standard 1500 bytes). Such behavior effectivly prevents interface start on boards with a low ammount of RAM (e.g. WRT300N v2), since the kernel simly can not allocates of ~0.8MB (14KB x 64). So remove jumbo frame support for now. Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net> Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ixp4xx: fix non-standard phy supportSergey Ryazanov2017-11-061-3/+25
| | | | | | | | | | | | | | | | | The patch, which adds multiphy support, adds new path for non-standard PHYs (e.g. MV88E6060 switch IC) to avoid using kernel phy framework. All work well except the link status traking (Duplex and Speed), which is reseted as soon as PHY connection procedure is done. This leads to lost of the link status of non-standard PHY, which is configured exactly in the ixp4xx_phy_connect() function. Move the generic reset of a link state to the ixp4xx_phy_connect() function to the code path, which is intended for handling of a normal PHY. Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net> Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* package: kernel: dtc: Add DTO supportMarek Vasut2017-11-061-0/+642
| | | | | | Add patch with the DT overlay support into the DTC package. Signed-off-by: Marek Vasut <marex@denx.de>
* openssl: fix cryptodev config dependencyRalph Sennhauser2017-11-061-0/+1
| | | | Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
* sunxi: Added profile for HAOYU Electronics Marsboard A10Kayo Phoenix2017-11-062-0/+16
| | | | | | | | | The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC. http://linux-sunxi.org/MarsBoard_A10 Signed-off-by: Kayo Phoenix <kayo@illumium.org> [Forward-ported to new target layout:] Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* iwinfo: add "PKG_MIRROR_HASH" to the MakefileArjun AK2017-11-061-0/+1
| | | | | | | Defining it will let the build tool download the tarball file from a buildbot server, avoiding a clone of the source repo. Signed-off-by: Arjun AK <lede@arjunak.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 15:36:04 +0000