aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* omap: add sysupgrade supportLucian Cristian2018-07-302-0/+109
| | | | | | add sysupgrade missing script files Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* omap: rename image for sysupgrade compatibilityLucian Cristian2018-07-302-14/+14
| | | | | | for sysupgrade to work we need to change the image name based on dts target name Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* omap: fix squashfs image boot and creationLucian Cristian2018-07-303-1/+5
| | | | | | | fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder also activate squashf image creation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* hostapd: add ht and vht support in handle event function Add ht and vht ↵Nick Hainke2018-07-303-2/+45
| | | | | | capabilities. If a device sends a probe request, the capabilities are added. Signed-off-by: Nick Hainke <vincent@systemli.org>
* hostapd: add ubus call for ap featuresNick Hainke2018-07-301-0/+16
| | | | | | | | | | | The call "get_features" allows to gather hostapd config options via ubus. As first infos we add the ht and vht support. Although nl80211 supports to gather informations about ht and vht capabilities, the hostapd configuration can disable vht and ht. However, it is possible that the iw output is not representing the actual hostapd configuration. Signed-off-by: Nick Hainke <vincent@systemli.org>
* uboot-envtools: add configuration for Traverse LS1043 boards.Mathew McBride2018-07-301-0/+25
| | | | Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: add Traverse LS1043-S supportMathew McBride2018-07-3011-8/+925
| | | | | | | | | | | | | | | | | | The Traverse LS1043-S board is a router board based on NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+, as well as miniPCIe and M.2 LTE. Unlike the Layerscape reference boards, the LS1043-S board has NAND flash and uses the mainline U-Boot. This patch implements support for the LS1043-S board, as well as the earlier LS1043-V board. It is our intention that all boards in this family (LS1043-S and later, Five64) will boot the same binary. Not included in this patchset are the hwmon drivers not in the kernel (emc1704,pac1934) or the bootloader. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: add multiple-configuration generator for FIT imagesMathew McBride2018-07-301-0/+596
| | | | | | | | | | | | | | | | | This is required for the Traverse LS1043 family, we generate a FIT image that works on all boards across the family. This is done by creating multiple configurations that select the right DTB for the board. The bootloader on these boards is configured to boot like this: bootm $kernel_load#ls1043s bootm $kernel_load#ls1043v This is based on earlier work by Jason Wu for Zynq: https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html Modified to add FDT load addresses and multiple configurations with DTB. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: add support for fixed-link on RGMII interfacesMathew McBride2018-07-301-0/+62
| | | | | | | | | This is required on the Traverse LS1043 boards to support SFP and xDSL plug-ins. This will not be needed on kernel 4.14. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: enable QorIQ thermal driverMathew McBride2018-07-301-0/+1
| | | | | | | This provides access to the CPU die temperature sensor and the thermal throttling integration Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: remove DEVICE_TYPE=developerboardMathew McBride2018-07-301-1/+0
| | | | | | | The Traverse LS1043 series are router boards and need the default router package selection Signed-off-by: Mathew McBride <matt@traverse.com.au>
* openvpn-easy-rsa: update to 3.0.4Luiz Angelo Daros de Luca2018-07-302-6/+31
| | | | | | | | | | | | | | Upstream renamed openssl-1.0.cnf to openssl-easyrsa.cnf. However, pkg kept using openssl-1.0.cnf. Upstream easyrsa searchs for vars, openssl-*, x509-types in the same directory as easyrsa script. This was patched to revert back to static /etc/easy-rsa/ directory (as does OpenSUSE). EASYRSA_PKI still depends on $PWD. Move easyrsa from /usr/sbin to /usr/bin as root is not needed. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* kernel: package x86-optimized crypto-misc modulesDaniel Gimpelevich2018-07-301-2/+50
| | | | | | | | | | | | Some of the modules in the crypto-misc package have alternate implementations optimized for different x86 instruction set extensions, but only one of these was built for this package until now: twofish-i586.ko Tested with insmod, on both x86 and x86_64. The modules now have an autoload, which they previous didn't, loading the dependencies in the correct order. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* kernel: generic: fix problem with w1-gpio-customPawel Dembicki2018-07-302-0/+86
| | | | | | | | | | In boards with fdt is impossible to use kmod-w1-gpio-custom. w1-gpio-custom create platform structure for w1-gpio module, but if board use fdt, data is ignored in w1-gpio probe. This workaround fix the problem. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix RBM11G nameThibaut VARÈNE2018-07-301-1/+1
| | | | | | | | The device name is corrected to match the hardware-stored (in hard config flash space) device name. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: fix RBM33G nameThibaut VARÈNE2018-07-301-1/+1
| | | | | | | | The device name is corrected to match the hardware-stored (in hard config flash space) device name. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* libevent: update to 2.1.8Leon M. George2018-07-302-15/+102
| | | | Signed-off-by: Leon M. George <leon@georgemail.eu>
* ramips: mmc: Add SD card support to HC5661ALoveSy2018-07-302-0/+5
| | | | | | | | | | Tested on HC5661A and it now fixes the issue that when enabling sd card in HC5661A, the wan and 3 lan ports will down. Known issue: - When enabling SD card support, the led light of system will down and the rest 2 lights keep working. Signed-off-by: LoveSy <shana@zju.edu.cn>
* ramips: mmc: Fix init for MT7628ANLoveSy2018-07-302-1/+16
| | | | | | | | There is another thing about crc to do when initialize SD card on MT7628. This commit is to fix this init issue. Signed-off-by: LoveSy <shana@zju.edu.cn>
* include: add netdev family support for nftablesRosy Song2018-07-301-0/+20
| | | | Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ncurses: install lib on host buildAndy Walsh2018-07-301-0/+2
| | | | Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
* iptables: add ip[6|]tables-compat packages + libxtables-compat depends on ↵Martin Strobel2018-07-301-0/+59
| | | | | | | | | IPTABLES_NFTABLES allows iptables-compat to use nft packet filtering allows to translate iptables-style to nft-style Signed-off-by: Martin Strobel <arctus@crza.de>
* config: Change conf.c remove compiler warningsPaul Schulz2018-07-301-6/+6
| | | | | | | | | | | | Compiler is producing the warning: warning: format not a string literal and no format arguments [-Wformat-security] This patch makes the format a literal string in printf statements. This with: gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3) in Ubuntu 18.04 Signed-off-by: Paul Schulz <paul@mawsonlakes.org>
* igmpproxy: drop SSDP packetsDmitry Tunin2018-07-302-1/+13
| | | | | | | It is insecure to let this type of packets inside They can e.g. open ports on some other routers with UPnP, etc Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ar71xx:add support for E750G v8张鹏2018-07-3012-2/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750G v8 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4G GHz (AR9344) - 2x 10/100 Mbps Ethernet (PoE support) - 2x 10/100/1000 Mbps Ethernet - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx:add support for E750A v4张鹏2018-07-3011-1/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750A v4 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 5G GHz (AR9344) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx:add support for E558 v2张鹏2018-07-3012-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9558) - 3x 10/100/1000 Mbps Ethernet (one port with PoE support) - 4x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 3-pos switch - 1x DC jack for main power input (9-48 V) - UART (JP5) and LEDs (J8) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* include/verbose.mk: Add sc to failure messageDaniel Engberg2018-07-301-1/+1
| | | | | | Add sc to build error message Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ar71xx: ag71xx: Prevent kernel oops for board defDaniel F. Dickinson2018-07-301-1/+15
| | | | | | | | | | | The driver is written in such a way that with a board defintion that connects a fixed phy, mdio, and switch in a certain way, a kernel oops could result because of lack of previously probed mdio bus. This commit allows for easier debugging in this case by casting the correct blame with serial console messages. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: ag71xx: Add connect message: fixed phyDaniel F. Dickinson2018-07-301-0/+7
| | | | | | | | It's a little noisier but makes it obvious when the ar7240 switch was connected to the MDIO bus, and to which phy device (or the failure to do so). Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: ag71xx_phy: Fix compilation for debug messagesDaniel F. Dickinson2018-07-301-2/+4
| | | | | | | | | | | NB: Error only appears with ag71xx debug messages and dynamic printk enabled. This is probably why no one has caught it before. Previously phy probe debug messages used old (now wrong) functions to get the phy name for printing. There was also the chance of a NULL pointer in the event no phy_device was found. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath10k: update QCA4019 firmwareMassimo Tum2018-07-301-1/+1
| | | | | | | | | | With AVM Fritz!Box 4040 and OpenWrt 18.06 RC1 there are many kernel warnings kern.warn kernel: [87771.917049] ath10k_ahb a000000.wifi: Invalid VHT mcs 15 peer stats and there are disconnections when the connected clients are many, at the moment I tried with 16 clients on 2.4 GHz and 8 on 5 GHZ. Firmware 10.4-3.5.3-00057 fixes these warnings and the problem of disconnections of some clients. Signed-off-by: Massimo Tum <masnia@tiscali.it>
* ath79: Add switch reset definition in dtsChuanhong Guo2018-07-307-0/+14
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: assert a switch reset if defined in dts.Chuanhong Guo2018-07-301-0/+9
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar724x: Fix reset definition for gmac0/gmac1Chuanhong Guo2018-07-303-12/+12
| | | | | | reset bit 8 is for builtin switch and bit 12 is marked 'reserved' on datasheet. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar7240: Update dts for current ag71xx driverChuanhong Guo2018-07-303-26/+20
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: Explicitly register mdio bus after ag71xx_hw_init() for ar7240Chuanhong Guo2018-07-301-0/+8
| | | | | | | | | | mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?) Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0 For ar7240 and older chips, manually create platform device after ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between ag71xx_hw_init() and ag71xx_phy_connect(). Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: Rework mdio clock settingsChuanhong Guo2018-07-302-26/+63
| | | | | | | Allow specifying desired mdio clock frequency in dts. Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar7242: Update dts for current ag71xx driverChuanhong Guo2018-07-301-2/+16
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar7241: Update dts for current ag71xx driverChuanhong Guo2018-07-306-44/+23
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: Fix support for TP-LINK Archer C7 v2Chuanhong Guo2018-07-303-46/+41
| | | | | | | | | | | | | | | | Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0. Add gmac-config for Archer C7. Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically. The following are for adding support for WDR4900 v2/Archer C7 v1 and other devices that shared the same machine file in ar71xx: Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash. Flash on Archer C7 v1/TL-WDR4900 v2 is 8M. Add label for wlan leds. The default trigger for archer c7/wdr4900 is different. Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380. Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qca955x: Update dts for current ag71xx driverChuanhong Guo2018-07-301-2/+2
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qca956x: Update dts for current ag71xx driverChuanhong Guo2018-07-302-4/+31
| | | | | | | | enable mdio1 by default because mdio1 node is a subnode of eth1 and eth1 node is a "simple-mfd", which makes mdio1 disabled when eth1 isn't enabled. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qca953x: Add chosen node and specify console in bootargsChuanhong Guo2018-07-301-0/+4
| | | | | | | Most qca devices use 115200n8 as it's default uart baudrate. Add 'chosen' node for qca953x like other SoCs in ath79 target. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qca953x: Update dts for current ag71xx driverChuanhong Guo2018-07-302-30/+36
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: update qca9533 to new irq driverLucian Cristian2018-07-302-24/+28
| | | | | | | | | | | | | | | | Commit c7efc93 renamed controller name to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked. Correct the dtsi and adust it to the new format Add gmac and correct reset for cascaded irq and build-in switch Also add the reference clock to soc dtsi so we don't have to have it in every dts Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> Remove switch reset definition Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.) Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar933x: Update dts for current ag71xx driverChuanhong Guo2018-07-307-81/+42
| | | | | | | | gmac0 is always connected to switch phy4 and mdio1 is always needed. So add phy handle for eth0 and enable mdio1 by default. Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar934x: Update dts for current ag71xx driverChuanhong Guo2018-07-303-4/+42
| | | | | | | | | Enable mdio1 by default because mdio1 is needed when eth1 is enabled. PS: If a ar9341 device has only one port and you only want to use gmac0, change compatible of gmac1 to "syscon", "simple-mfd" in dts. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: Make builtin switch driver a separated moduleChuanhong Guo2018-07-302-68/+84
| | | | | | | | | This patch did several things: 1. Probe the builtin switch as a separated mdio device. 2. Register a separated mdio bus for builtin switch. 3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: Split mdio driver into an independent platform device.Chuanhong Guo2018-07-304-84/+78
| | | | | | | We need to have mdio1 belonging to gmac1 initialized before gmac0. Split it into a separated mdio device to get both mdios ready before probing gmac. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 04:29:56 +0000