diff options
Diffstat (limited to 'target')
7 files changed, 411 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 6a94fe3ff4..ecdbac8f86 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -17,6 +17,7 @@ ipq40xx_setup_interfaces() engenius,emr3500|\ engenius,ens620ext|\ luma,wrtq-329acn|\ + netgear,wac510|\ plasmacloud,pa1200|\ plasmacloud,pa2200) ucidef_set_interfaces_lan_wan "eth0" "eth1" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index b12c9af9a7..42cb295496 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -150,6 +150,10 @@ case "$FIRMWARE" in caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0) ;; + netgear,wac510) + caldata_extract "0:ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary "0:MANUDATA" 0x6) + ;; zyxel,nbg6617 |\ zyxel,wre6606) caldata_extract "ART" 0x1000 0x2f20 @@ -260,6 +264,10 @@ case "$FIRMWARE" in caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc) ;; + netgear,wac510) + caldata_extract "0:ART" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:MANUDATA" 0x6) +16) + ;; zyxel,nbg6617 |\ zyxel,wre6606) caldata_extract "ART" 0x5000 0x2f20 diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount index d2a4abcadd..9abfbddc43 100755 --- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -13,5 +13,8 @@ boot() { linksys,mr8300) mtd resetbc s_env || true ;; + netgear,wac510) + fw_setenv boot_cnt=0 + ;; esac } diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 54683977cd..68027be666 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -72,6 +72,7 @@ platform_do_upgrade() { glinet,gl-ap1300 |\ luma,wrtq-329acn |\ mobipromo,cm520-79f |\ + netgear,wac510 |\ qxwlan,e2600ac-c2) nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wac510.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wac510.dts new file mode 100644 index 0000000000..20e12855f4 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wac510.dts @@ -0,0 +1,371 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */ + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "Netgear WAC510"; + compatible = "netgear,wac510"; + + aliases { + led-boot = &led_power_amber; + led-failsafe = &led_power_amber; + led-running = &led_power_green; + led-upgrade = &led_power_amber; + label-mac-device = &gmac0; + }; + + chosen { + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + status = "okay"; + + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2: usb2@60f8800 { + status = "okay"; + }; + + usb3: usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + + ssr: ssr@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_amber: power_amber { + label = "amber:power"; + gpios = <&ssr 6 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + led_power_green: power_green { + label = "green:power"; + gpios = <&ssr 5 GPIO_ACTIVE_LOW>; + }; + + wlan2g_blue { + label = "blue:wlan2g"; + gpios = <&ssr 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan2g_green { + label = "green:wlan2g"; + gpios = <&ssr 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0radio"; + }; + + wlan5g_blue { + label = "blue:wlan5g"; + gpios = <&ssr 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g_green { + label = "green:wlan5g"; + gpios = <&ssr 1 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1radio"; + }; + + act_green { + label = "green:act"; + gpios = <&ssr 0 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0x000f0000 0x000f0000>; + read-only; + }; + + partition@1e0000 { + label = "0:MANUDATA"; + reg = <0x001e0000 0x00010000>; + read-only; + }; + + partition@1f0000 { + label = "0:ART"; + reg = <0x001f0000 0x00010000>; + read-only; + }; + }; + }; + + nand@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <48000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x00000000 0x03800000>; + }; + + partition@3800000 { + label = "rootfs_1"; + reg = <0x03800000 0x03800000>; + }; + + partition@7000000 { + label = "var_config"; + reg = <0x07000000 0x00f00000>; + read-only; + }; + + partition@7f00000 { + label = "Oops_log"; + reg = <0x07f00000 0x000c0000>; + read-only; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; + reset-delay-us = <2000>; +}; + +&gmac0 { + qcom,forced_duplex = <1>; + qcom,forced_speed = <1000>; + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + vlan_tag = <1 0x10>; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Netgear-WAC510"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Netgear-WAC510"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 4e40b8be50..2d6186ed99 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -62,6 +62,16 @@ define Build/mkmylofw_32m @mv $@.new $@ endef +define Build/wac5xx-netgear-tar + mkdir $@.tmp + mv $@ $@.tmp/wac5xx-ubifs-root.img + md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum + echo "WAC505 WAC510" > $@.tmp/metadata.txt + echo "WAC505_V9.9.9.9" > $@.tmp/version + tar -C $@.tmp/ -cf $@ . + rm -rf $@.tmp +endef + define Build/qsdk-ipq-factory-nand-askey $(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\ askey_kernel $(IMAGE_KERNEL) \ @@ -636,6 +646,21 @@ define Device/netgear_ex6150v2 endef TARGET_DEVICES += netgear_ex6150v2 +define Device/netgear_wac510 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Netgear + DEVICE_MODEL := WAC510 + SOC := qcom-ipq4018 + DEVICE_DTS_CONFIG := config@5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGES += nand-factory.tar + IMAGE/nand-factory.tar := append-ubi | wac5xx-netgear-tar + DEVICE_PACKAGES := uboot-envtools +endef +TARGET_DEVICES += netgear_wac510 + define Device/openmesh_a42 $(call Device/FitImageLzma) DEVICE_VENDOR := OpenMesh diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 6b7c68bf63..0447fb6012 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,60 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,61 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -37,6 +37,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-oap100.dtb \ + qcom-ipq4018-pa1200.dtb \ + qcom-ipq4018-rt-ac58u.dtb \ ++ qcom-ipq4018-wac510.dtb \ + qcom-ipq4018-wre6606.dtb \ + qcom-ipq4018-wrtq-329acn.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ |