diff options
Diffstat (limited to 'target/linux')
12 files changed, 931 insertions, 2 deletions
diff --git a/target/linux/ipq806x/Makefile b/target/linux/ipq806x/Makefile index 862ad7da00..5c89d413c0 100644 --- a/target/linux/ipq806x/Makefile +++ b/target/linux/ipq806x/Makefile @@ -5,10 +5,10 @@ include $(TOPDIR)/rules.mk ARCH:=arm BOARD:=ipq806x BOARDNAME:=Qualcomm Atheros IPQ806X -FEATURES:=squashfs nand fpu ramdisk +FEATURES:=squashfs fpu ramdisk CPU_TYPE:=cortex-a15 CPU_SUBTYPE:=neon-vfpv4 -SUBTARGETS:=generic +SUBTARGETS:=generic chromium KERNEL_PATCHVER:=5.15 diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index dbff854731..f38876b69f 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -79,6 +79,12 @@ tplink,ad7200) ucidef_add_switch "switch0" \ "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "6@eth1" "1:wan" "0@eth0" ;; +asus,onhub |\ +tplink,onhub) + ucidef_set_interfaces_lan_wan "eth1" "eth0" + ucidef_add_switch "switch0" \ + "1:lan" "6@eth1" "2:wan" "0@eth0" + ;; ubnt,unifi-ac-hd) ucidef_set_interface_lan "eth0 eth1" ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 398ddf9a29..a0e2e9d123 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -6,9 +6,32 @@ board=$(board_name) +dt_base64_extract() { + local target_dir="/sys$DEVPATH" + local source="$target_dir/../../of_node/qcom,ath10k-calibration-data-base64" + + [ -e "$source" ] || caldata_die "cannot find base64 calibration data: $source" + [ -d "$target_dir" ] || \ + caldata_die "no sysfs dir to write: $target" + + echo 1 > "$target_dir/loading" + base64decode.uc "$source" > "$target_dir/data" + if [ $? != 0 ]; then + echo 1 > "$target_dir/loading" + caldata_die \ + "failed to write calibration data to $target_dir/data" + else + echo 0 > "$target_dir/loading" + fi +} + case "$FIRMWARE" in "ath10k/cal-pci-0000:01:00.0.bin") case "$board" in + asus,onhub |\ + tplink,onhub) + dt_base64_extract + ;; meraki,mr52) CI_UBIPART=art caldata_extract_ubi "ART" 0x1000 0x844 @@ -35,6 +58,14 @@ case "$FIRMWARE" in ;; esac ;; +"ath10k/cal-pci-0001:01:00.0.bin") + case "$board" in + asus,onhub |\ + tplink,onhub) + dt_base64_extract + ;; + esac + ;; "ath10k/pre-cal-pci-0001:01:00.0.bin") case $board in asrock,g10) @@ -61,6 +92,10 @@ case "$FIRMWARE" in ;; "ath10k/cal-pci-0002:01:00.0.bin") case "$board" in + asus,onhub |\ + tplink,onhub) + dt_base64_extract + ;; meraki,mr42) CI_UBIPART=art caldata_extract_ubi "ART" 0x9000 0x844 diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index f9e592f4bd..67ceaab24f 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -57,6 +57,15 @@ platform_do_upgrade() { MTD_CONFIG_ARGS="-s 0x200000" default_do_upgrade "$1" ;; + asus,onhub |\ + tplink,onhub) + export_bootdevice + export_partdevice CI_ROOTDEV 0 + CI_KERNPART="kernel" + CI_ROOTPART="rootfs" + CI_DATAPART="rootfs_data" + emmc_do_upgrade "$1" + ;; tplink,vr2600v) MTD_CONFIG_ARGS="-s 0x200000" default_do_upgrade "$1" @@ -69,3 +78,13 @@ platform_do_upgrade() { ;; esac } + +platform_copy_config() { + case "${board_name}" in + asus,onhub |\ + tplink,onhub) + emmc_copy_config + ;; + esac + return 0 +} diff --git a/target/linux/ipq806x/base-files/usr/bin/base64decode.uc b/target/linux/ipq806x/base-files/usr/bin/base64decode.uc new file mode 100755 index 0000000000..7dcf30986c --- /dev/null +++ b/target/linux/ipq806x/base-files/usr/bin/base64decode.uc @@ -0,0 +1,23 @@ +#!/usr/bin/ucode + +import { stdin, open, error } from 'fs'; + +if (length(ARGV) == 0 && stdin.isatty()) { + warn("usage: b64decode [stdin|path]\n"); + exit(1); +} + +let fp = stdin; +let source = ARGV[0]; + +if (source) { + fp = open(source); + if (!fp) { + warn('b64decode: unable to open ${source}: ${error()}\n'); + exit(1); + } +} + +print(b64dec(fp.read("all"))); +fp.close(); +exit(0); diff --git a/target/linux/ipq806x/chromium/config-default b/target/linux/ipq806x/chromium/config-default new file mode 100644 index 0000000000..d7db9f7db3 --- /dev/null +++ b/target/linux/ipq806x/chromium/config-default @@ -0,0 +1,13 @@ +CONFIG_BLK_DEV_SD=y +CONFIG_LEDS_LP5523=y +CONFIG_LEDS_LP55XX_COMMON=y +CONFIG_PHY_QCOM_IPQ806X_USB=y +CONFIG_SCSI=y +CONFIG_SCSI_COMMON=y +CONFIG_SG_POOL=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_HOST=y +CONFIG_USB_DWC3_QCOM=y +CONFIG_USB_STORAGE=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PLATFORM=y diff --git a/target/linux/ipq806x/chromium/target.mk b/target/linux/ipq806x/chromium/target.mk new file mode 100644 index 0000000000..3983a9281a --- /dev/null +++ b/target/linux/ipq806x/chromium/target.mk @@ -0,0 +1,2 @@ +BOARDNAME:=Google Chromium +FEATURES += emmc boot-part rootfs-part diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-asus-onhub.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-asus-onhub.dts new file mode 100644 index 0000000000..5b60ddb04b --- /dev/null +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-asus-onhub.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2014 The ChromiumOS Authors + */ + +#include "qcom-ipq8064-onhub.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/soc/qcom,gsbi.h> + +/ { + model = "ASUS OnHub"; + compatible = "asus,onhub", "google,arkham", "qcom,ipq8064"; + + chosen { + bootargs-append = " rootwait"; + }; +}; + +&qcom_pinmux { + ap3223_pins: ap3223_pinmux { + pins = "gpio22"; + function = "gpio"; + bias-none; + }; + + i2c7_pins: i2c7_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "gsbi7"; + }; + data { + pins = "gpio8"; + bias-disable; + }; + clk { + pins = "gpio9"; + bias-disable; + }; + }; +}; + +&gsbi7 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C_UART>; +}; + +&gsbi7_i2c { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c7_pins>; + pinctrl-names = "default"; + + ap3223@1c { + compatible = "dynaimage,ap3223"; + reg = <0x1c>; + + pinctrl-0 = <&ap3223_pins>; + pinctrl-names = "default"; + + int-gpio = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>; + }; + + led-controller@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + #address-cells = <1>; + #size-cells = <0>; + + led@4 { + reg = <4>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0xfa>; + max-cur = /bits/ 8 <0xff>; + }; + + led@5 { + reg = <5>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status"; + led-cur = /bits/ 8 <0xfa>; + max-cur = /bits/ 8 <0xff>; + }; + + led@8 { + reg = <8>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status"; + led-cur = /bits/ 8 <0xfa>; + max-cur = /bits/ 8 <0xff>; + }; + }; +}; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-onhub.dtsi b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-onhub.dtsi new file mode 100644 index 0000000000..25ba71da00 --- /dev/null +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-onhub.dtsi @@ -0,0 +1,463 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2014 The ChromiumOS Authors + */ + +#include "qcom-ipq8064-smb208.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac2; + mdio-gpio0 = &mdio; + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + mdio: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, + <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + soc { + rng@1a500000 { + status = "disabled"; + }; + + sound { + compatible = "google,storm-audio"; + qcom,model = "ipq806x-storm"; + cpu = <&lpass>; + codec = <&max98357a>; + }; + + lpass: lpass@28100000 { + status = "okay"; + pinctrl-names = "default", "idle"; + pinctrl-0 = <&mi2s_default>; + pinctrl-1 = <&mi2s_idle>; + }; + + max98357a: max98357a { + compatible = "maxim,max98357a"; + #sound-dai-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmode_pins>; + sdmode-gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + rgmii0_pins: rgmii0_pins { + mux { + pins = "gpio2", "gpio66"; + drive-strength = <8>; + bias-disable; + }; + }; + mi2s_pins { + mi2s_default: mi2s_default { + dout { + pins = "gpio32"; + function = "mi2s"; + drive-strength = <16>; + bias-disable; + }; + sync { + pins = "gpio27"; + function = "mi2s"; + drive-strength = <16>; + bias-disable; + }; + clk { + pins = "gpio28"; + function = "mi2s"; + drive-strength = <16>; + bias-disable; + }; + }; + mi2s_idle: mi2s_idle { + dout { + pins = "gpio32"; + function = "mi2s"; + drive-strength = <2>; + bias-pull-down; + }; + sync { + pins = "gpio27"; + function = "mi2s"; + drive-strength = <2>; + bias-pull-down; + }; + clk { + pins = "gpio28"; + function = "mi2s"; + drive-strength = <2>; + bias-pull-down; + }; + }; + }; + + mdio_pins: mdio_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + rst { + pins = "gpio26"; + output-low; + }; + }; + + sdmode_pins: sdmode_pinmux { + pins = "gpio25"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + sdcc1_pins: sdcc1_pinmux { + mux { + pins = "gpio38", "gpio39", "gpio40", + "gpio41", "gpio42", "gpio43", + "gpio44", "gpio45", "gpio46", + "gpio47"; + function = "sdc1"; + }; + cmd { + pins = "gpio45"; + drive-strength = <10>; + bias-pull-up; + }; + data { + pins = "gpio38", "gpio39", "gpio40", + "gpio41", "gpio43", "gpio44", + "gpio46", "gpio47"; + drive-strength = <10>; + bias-pull-up; + }; + clk { + pins = "gpio42"; + drive-strength = <16>; + bias-pull-down; + }; + }; + + i2c1_pins: i2c1_pinmux { + pins = "gpio53", "gpio54"; + function = "gsbi1"; + bias-disable; + }; + + rpm_i2c_pinmux: rpm_i2c_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + /delete-property/ bias-none; + /delete-property/ drive-strength; + }; + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + fw_pinmux { + wp { + pins = "gpio17"; + output-low; + }; + recovery { + pins = "gpio16"; + bias-none; + }; + developer { + pins = "gpio15"; + bias-none; + }; + }; + + spi6_pins: spi6_pins { + mux { + pins = "gpio55", "gpio56", "gpio58"; + function = "gsbi6"; + bias-pull-down; + }; + data { + pins = "gpio55", "gpio56"; + drive-strength = <10>; + }; + cs { + pins = "gpio57"; + drive-strength = <10>; + bias-pull-up; + output-high; + }; + clk { + pins = "gpio58"; + drive-strength = <12>; + }; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <0>; + phy-handle = <&phy1>; + + pinctrl-0 = <&rgmii0_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + phy-handle = <&phy0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi1 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C_UART>; +}; + +&gsbi1_i2c { + status = "okay"; + + clock-frequency = <100000>; + + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + powered-while-suspended; + }; +}; + +&gsbi4 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C_UART>; +}; + +&gsbi4_serial { + status = "okay"; +}; + +&gsbi5 { + status = "okay"; + qcom,mode = <GSBI_PROT_SPI>; + + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 0>; + + flash: flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; +}; + +&gsbi6 { + status = "okay"; + qcom,mode = <GSBI_PROT_SPI>; +}; + +&gsbi6_spi { + status = "okay"; + spi-max-frequency = <25000000>; + + pinctrl-0 = <&spi6_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; + + dmas = <&adm_dma 8 0xb>, + <&adm_dma 7 0x14>; + dma-names = "rx", "tx"; + + /* + * This "spidev" was included in the manufacturer device tree. I suspect + * it's the (unused) Zigbee radio -- SiliconLabs EM3581 Zigbee? There's + * no driver or binding for this at the moment. + */ + spidev@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <25000000>; + }; +}; + +&pcie0 { + status = "okay"; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-sa-gpio = <2 3 4 0>; + qcom,ath10k-sa-gpio-func = <5 5 5 0>; + }; + }; +}; + +&pcie1 { + status = "okay"; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-sa-gpio = <2 3 4 0>; + qcom,ath10k-sa-gpio-func = <5 5 5 0>; + }; + }; +}; + +&pcie2 { + status = "okay"; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + }; + }; +}; + +&rpm { + pinctrl-0 = <&rpm_i2c_pinmux>; + pinctrl-names = "default"; +}; + +&sdcc1 { + status = "okay"; + pinctrl-0 = <&sdcc1_pins>; + pinctrl-names = "default"; + /delete-property/ mmc-ddr-1_8v; +}; + +&tcsr { + compatible = "qcom,tcsr-ipq8064", "qcom,tcsr", "syscon"; + qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>; +}; + +&hs_phy_0 { + status = "okay"; +}; + +&ss_phy_0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&hs_phy_1 { + status = "okay"; +}; + +&ss_phy_1 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-tplink-onhub.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-tplink-onhub.dts new file mode 100644 index 0000000000..6dd39f0d95 --- /dev/null +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8064-tplink-onhub.dts @@ -0,0 +1,213 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2014 The ChromiumOS Authors + */ + +#include "qcom-ipq8064-onhub.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/soc/qcom,gsbi.h> + +/ { + model = "TP-Link OnHub"; + compatible = "tplink,onhub", "google,whirlwind-sp5", "qcom,ipq8064"; + + chosen { + bootargs-append = " rootwait"; + }; +}; + +&qcom_pinmux { + i2c7_pins: i2c7_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "gsbi7"; + }; + data { + pins = "gpio8"; + bias-disable; + }; + clk { + pins = "gpio9"; + bias-disable; + }; + }; +}; + +&gsbi7 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C_UART>; +}; + +&gsbi7_i2c { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c7_pins>; + pinctrl-names = "default"; + + led-controller@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-0"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-0"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-0"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-1"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@4 { + reg = <4>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-1"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@5 { + reg = <5>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-1"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@6 { + reg = <6>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-2"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@7 { + reg = <7>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-2"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@8 { + reg = <8>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-2"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + }; + + led-controller@33 { + compatible = "national,lp5523"; + reg = <0x33>; + clock-mode = /bits/ 8 <1>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-3"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-3"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-3"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-4"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@4 { + reg = <4>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-4"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@5 { + reg = <5>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-4"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@6 { + reg = <6>; + color = <LED_COLOR_ID_RED>; + chan-name = "red:status-5"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@7 { + reg = <7>; + color = <LED_COLOR_ID_GREEN>; + chan-name = "green:status-5"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + + led@8 { + reg = <8>; + color = <LED_COLOR_ID_BLUE>; + chan-name = "blue:status-5"; + linux,default-trigger = "default-on"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + }; + }; +}; diff --git a/target/linux/ipq806x/generic/target.mk b/target/linux/ipq806x/generic/target.mk index f5cb1fb19b..4de636f0e0 100644 --- a/target/linux/ipq806x/generic/target.mk +++ b/target/linux/ipq806x/generic/target.mk @@ -1 +1,2 @@ BOARDNAME:=Generic +FEATURES += nand diff --git a/target/linux/ipq806x/image/chromium.mk b/target/linux/ipq806x/image/chromium.mk new file mode 100644 index 0000000000..16af6b95ba --- /dev/null +++ b/target/linux/ipq806x/image/chromium.mk @@ -0,0 +1,58 @@ +define Build/cros-gpt + cp $@ $@.tmp 2>/dev/null || true + ptgen -o $@.tmp -g \ + -T cros_kernel -N kernel -p $(CONFIG_TARGET_KERNEL_PARTSIZE)m \ + -N rootfs -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)m \ + -N rootfs_data -p \ + $$((3687-$(CONFIG_TARGET_ROOTFS_PARTSIZE)-\ + $(CONFIG_TARGET_KERNEL_PARTSIZE)))m + cat $@.tmp >> $@ + rm $@.tmp +endef + +define Build/append-kernel-part + dd if=$(IMAGE_KERNEL) bs=$(CONFIG_TARGET_KERNEL_PARTSIZE)M conv=sync >> $@ +endef + +# NB: Chrome OS bootloaders replace the '%U' in command lines with the UUID of +# the kernel partition it chooses to boot from. This gives a flexible way to +# consistently build and sign kernels that always use the subsequent +# (PARTNROFF=1) partition as their rootfs. +define Build/cros-vboot + $(STAGING_DIR_HOST)/bin/cros-vbutil \ + -k $@ -c "root=PARTUUID=%U/PARTNROFF=1" -o $@.new + @mv $@.new $@ +endef + +define Device/OnhubImage + KERNEL_LOADADDR = 0x44208000 + SOC := qcom-ipq8064 + KERNEL_SUFFIX := -fit-zImage.itb.vboot + KERNEL_NAME := zImage + KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb | cros-vboot + IMAGES := factory.bin sysupgrade.bin + IMAGE/factory.bin := cros-gpt | append-kernel-part | append-rootfs + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct e2fsprogs kmod-fs-ext4 losetup \ + partx-utils mkf2fs kmod-fs-f2fs \ + ucode kmod-google-firmware kmod-tpm-i2c-infineon \ + kmod-sound-soc-ipq8064-storm kmod-usb-storage +endef + +define Device/asus_onhub + $(call Device/OnhubImage) + DEVICE_VENDOR := ASUS + DEVICE_MODEL := OnHub SRT-AC1900 + DEVICE_DTS := $$(SOC)-asus-onhub + BOARD_NAME := asus-onhub +endef +TARGET_DEVICES += asus_onhub + +define Device/tplink_onhub + $(call Device/OnhubImage) + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := OnHub AC1900 Cloud Router + DEVICE_DTS := $$(SOC)-tplink-onhub + BOARD_NAME := tplink-onhub +endef +TARGET_DEVICES += tplink_onhub |