diff options
Diffstat (limited to 'target/linux')
7 files changed, 286 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index 8942ad2000..16039c8c42 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -22,7 +22,8 @@ avm,fritzbox-4040) ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x1e" ;; avm,fritzbox-7530 |\ -glinet,gl-b1300) +glinet,gl-b1300 |\ +mikrotik,lhgg-60ad) ucidef_set_led_wlan "wlan" "WLAN" "green:wlan" "phy0tpt" ;; edgecore,oap100) diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 12e67387fa..63209fa49a 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -29,6 +29,7 @@ ipq40xx_setup_interfaces() engenius,eap1300|\ engenius,emd1|\ meraki,mr33|\ + mikrotik,lhgg-60ad|\ mikrotik,sxtsq-5-ac|\ netgear,ex6100v2|\ netgear,ex6150v2|\ @@ -190,6 +191,7 @@ ipq40xx_setup_macs() lan_mac=$(macaddr_add $wan_mac 1) label_mac="$wan_mac" ;; + mikrotik,lhgg-60ad|\ mikrotik,sxtsq-5-ac) lan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base) label_mac="$lan_mac" diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index bd55b1712b..8f8494dcff 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -133,6 +133,7 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; mikrotik,hap-ac2|\ + mikrotik,lhgg-60ad|\ mikrotik,sxtsq-5-ac) [ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware default_do_upgrade "$1" diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-lhgg-60ad.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-lhgg-60ad.dts new file mode 100644 index 0000000000..bd61f4b69f --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-lhgg-60ad.dts @@ -0,0 +1,269 @@ +/* Copyright (c) 2015, The Linux Foundation. All rights reserved. + * Copyright (c) 2019, Robert Marko <robimarko@gmail.com> + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "Mikrotik Wireless Wire Dish LHGG-60ad"; + compatible = "mikrotik,lhgg-60ad"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + led-boot = &user; + led-failsafe = &user; + led-running = &user; + led-upgrade = &user; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + + /delete-node/ ethernet-phy@1; + /delete-node/ ethernet-phy@2; + /delete-node/ ethernet-phy@3; + /delete-node/ ethernet-phy@4; + /delete-node/ psgmii-phy@5; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */ + switch_lan_bmp = <0x0>; /* lan port bitmap */ + switch_wan_bmp = <0x10>; /* wan port bitmap */ + }; + + edma@c080000 { + status = "okay"; + phy-mode = "rgmii-id"; + qcom,num_gmac = <1>; + qcom,single-phy; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: power { + label = "blue:power"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + panic-indicator; + }; + + user: user { + label = "yellow:user"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + }; + + wlan { + label = "green:wlan"; + gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>; + }; + + align-left { + label = "green:align-left"; + gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; + }; + + align-right { + label = "green:align-right"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + + wlan-rx { + label = "green:align-down"; + gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>; + }; + + wlan-tx { + label = "green:align-up"; + gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi-0-pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + status = "okay"; + + m25p80@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Qualcomm"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + compatible = "mikrotik,routerboot-partitions"; + #address-cells = <1>; + #size-cells = <1>; + label = "RouterBoot"; + reg = <0x80000 0x80000>; + read-only; + + hard_config { + read-only; + size = <0x2000>; + }; + + dtb_config { + read-only; + }; + + soft_config { + }; + }; + + partition@100000 { + compatible = "mikrotik,minor"; + label = "firmware"; + reg = <0x100000 0xf00000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 42 GPIO_ACTIVE_HIGH>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + /* wil6210 802.11ad card */ + wifi: wifi@1,0 { + status = "okay"; + /* wil6210 driver has no compatible */ + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&gmac0 { + qcom,phy_mdio_addr = <0>; + qcom,poll_required = <1>; + vlan_tag = <0 0x20>; +}; diff --git a/target/linux/ipq40xx/image/mikrotik.mk b/target/linux/ipq40xx/image/mikrotik.mk index bfff58597f..2fdaad60ab 100644 --- a/target/linux/ipq40xx/image/mikrotik.mk +++ b/target/linux/ipq40xx/image/mikrotik.mk @@ -40,6 +40,14 @@ define Device/mikrotik_hap-ac3 endef TARGET_DEVICES += mikrotik_hap-ac3 +define Device/mikrotik_lhgg-60ad + $(call Device/mikrotik_nor) + DEVICE_MODEL := Wireless Wire Dish LHGG-60ad + DEVICE_DTS := qcom-ipq4019-lhgg-60ad + DEVICE_PACKAGES += -kmod-ath10k-ct -ath10k-firmware-qca4019-ct kmod-wil6210 +endef +TARGET_DEVICES += mikrotik_lhgg-60ad + define Device/mikrotik_sxtsq-5-ac $(call Device/mikrotik_nor) DEVICE_MODEL := SXTsq 5 ac (RBSXTsqG-5acD) diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index 9817e9c102..3bd13bf932 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -902,11 +902,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -58,6 +58,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-habanero-dvk.dtb \ + qcom-ipq4019-hap-ac3.dtb \ + qcom-ipq4019-map-ac2200.dtb \ ++ qcom-ipq4019-lhgg-60ad.dtb \ + qcom-ipq4019-mr8300.dtb \ + qcom-ipq4019-pa2200.dtb \ + qcom-ipq4019-r619ac-64m.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index bda2b014a4..734d08387a 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,67 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -55,6 +55,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-fritzrepeater-3000.dtb \ + qcom-ipq4019-hap-ac3.dtb \ + qcom-ipq4019-map-ac2200.dtb \ ++ qcom-ipq4019-lhgg-60ad.dtb \ + qcom-ipq4019-mr8300.dtb \ + qcom-ipq4019-e2600ac-c1.dtb \ + qcom-ipq4019-e2600ac-c2.dtb \ |