aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/ipq40xx')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/01_leds1
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh1
-rw-r--r--target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts325
-rw-r--r--target/linux/ipq40xx/image/Makefile12
-rw-r--r--target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch9
7 files changed, 348 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 0a128e8cbc..e9e0de9da9 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -62,6 +62,7 @@ zyxel,nbg6617)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
;;
+edgecore,ecw5211 |\
zyxel,wre6606)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy1tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 61d02a17bc..571479aaf2 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -38,6 +38,7 @@ ipq40xx_setup_interfaces()
;;
asus,map-ac2200|\
cilab,meshpoint-one|\
+ edgecore,ecw5211|\
openmesh,a42|\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8df7990f2e..d85424142b 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -93,6 +93,7 @@ case "$FIRMWARE" in
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
+ edgecore,ecw5211 |\
engenius,eap1300 |\
engenius,eap2200 |\
openmesh,a42 |\
@@ -186,6 +187,7 @@ case "$FIRMWARE" in
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
+ edgecore,ecw5211 |\
engenius,eap1300 |\
engenius,eap2200 |\
openmesh,a42 |\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 5b89710a22..ae5a0a7c1b 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -66,6 +66,7 @@ platform_do_upgrade() {
avm,fritzrepeater-3000 |\
buffalo,wtr-m2133hp |\
cilab,meshpoint-one |\
+ edgecore,ecw5211 |\
engenius,eap2200 |\
mobipromo,cm520-79f |\
qxwlan,e2600ac-c2)
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts
new file mode 100644
index 0000000000..3f7e2ad6fd
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-ecw5211.dts
@@ -0,0 +1,325 @@
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Edgecore ECW5211";
+ compatible = "edgecore,ecw5211";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs-append = " root=/dev/ubiblock0_1";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "ecw5211:yellow:power";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "ecw5211:green:wlan2g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g {
+ label = "ecw5211:green:wlan5g";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ status = "okay";
+
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio_pinmux {
+ mux_mdio {
+ pins = "gpio53";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_mdc {
+ pins = "gpio52";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ i2c0_pins: i2c0_pinmux {
+ mux_i2c {
+ function = "blsp_i2c0";
+ pins = "gpio58", "gpio59";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ status = "okay";
+
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "0:APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "0:APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ spi-nand@1 {
+ status = "okay";
+
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "rootfs";
+ reg = <0x00000000 0x04000000>;
+ };
+ };
+ };
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+
+ tpm@29 {
+ compatible = "atmel,at97sc3204t";
+ reg = <0x29>;
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <4>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <3>;
+ vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+ status = "okay";
+
+ qcom,ath10k-calibration-variant = "Edgecore-ECW5211";
+};
+
+&wifi1 {
+ status = "okay";
+
+ qcom,ath10k-calibration-variant = "Edgecore-ECW5211";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 51e8bcc7e3..127af99ce5 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -344,6 +344,18 @@ define Device/dlink_dap-2610
endef
TARGET_DEVICES += dlink_dap-2610
+define Device/edgecore_ecw5211
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_TITLE := Edgecore ECW5211
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
+ DEVICE_DTS := qcom-ipq4018-ecw5211
+ DEVICE_PACKAGES := ipq-wifi-edgecore_ecw5211 kmod-tpm-i2c-atmel kmod-usb-acm uboot-envtools
+endef
+TARGET_DEVICES += edgecore_ecw5211
+
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index d281bb468d..ea45606c27 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -8,9 +8,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,50 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+Index: linux-5.4.63/arch/arm/boot/dts/Makefile
+===================================================================
+--- linux-5.4.63.orig/arch/arm/boot/dts/Makefile
++++ linux-5.4.63/arch/arm/boot/dts/Makefile
+@@ -837,11 +837,51 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -20,6 +22,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
+ qcom-ipq4018-ea6350v3.dtb \
+ qcom-ipq4018-eap1300.dtb \
++ qcom-ipq4018-ecw5211.dtb \
+ qcom-ipq4018-emd1.dtb \
+ qcom-ipq4018-emr3500.dtb \
+ qcom-ipq4018-ens620ext.dtb \
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 11:25:16 +0000