diff options
Diffstat (limited to 'target/linux/ipq40xx')
6 files changed, 296 insertions, 2 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 2966fbf1fb..d744e9b7e2 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -16,7 +16,8 @@ ipq40xx_setup_interfaces() 8dev,jalapeno|\ alfa-network,ap120c-ac|\ engenius,emr3500|\ - engenius,ens620ext) + engenius,ens620ext|\ + luma,wrtq-329acn) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; aruba,ap-303|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index d68e8d54b8..7a7464cf9a 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -97,6 +97,7 @@ case "$FIRMWARE" in edgecore,oap100 |\ engenius,eap1300 |\ engenius,eap2200 |\ + luma,wrtq-329acn|\ openmesh,a42 |\ openmesh,a62 |\ qxwlan,e2600ac-c1 |\ @@ -192,6 +193,7 @@ case "$FIRMWARE" in edgecore,oap100 |\ engenius,eap1300 |\ engenius,eap2200 |\ + luma,wrtq-329acn|\ openmesh,a42 |\ openmesh,a62 |\ qxwlan,e2600ac-c1 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 0bae8e1681..e09ab0344b 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -69,6 +69,7 @@ platform_do_upgrade() { edgecore,ecw5211 |\ edgecore,oap100 |\ engenius,eap2200 |\ + luma,wrtq-329acn |\ mobipromo,cm520-79f |\ qxwlan,e2600ac-c2) nand_do_upgrade "$1" diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wrtq-329acn.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wrtq-329acn.dts new file mode 100644 index 0000000000..faac71489c --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wrtq-329acn.dts @@ -0,0 +1,277 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +#include "qcom-ipq4019.dtsi" + +/ { + model = "Luma Home WRTQ-329ACN"; + compatible = "luma,wrtq-329acn"; + + i2c-gpio { + compatible = "i2c-gpio"; + sda-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + /* No driver exists */ + led_ring@48 { + compatible = "ti,msp430"; + reg = <0x48>; + }; + + eeprom@50 { + compatible = "atmel,24c16"; + reg = <0x50>; + pagesize = <16>; + read-only; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + + /delete-node/ ethernet-phy@0; + /delete-node/ ethernet-phy@1; + /delete-node/ ethernet-phy@3; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + + switch_lan_bmp = <0x1e>; + switch_wan_bmp = <0x20>; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + + +&blsp1_spi1 { + status = "okay"; + + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 59 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x040000 0x020000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x060000 0x060000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0x0c0000 0x010000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x0d0000 0x010000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0x0e0000 0x010000>; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0x0f0000 0x080000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x010000>; + read-only; + }; + }; + }; + + flash@1 { + status = "okay"; + + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x0000000 0x8000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <2>; + qcom,poll_required = <1>; +}; + +&gmac1 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; +}; + +&tlmm { + serial0_pins: serial0_pinmux { + mux { + function = "blsp_uart0"; + pins = "gpio60", "gpio61"; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + bias-disable; + drive-strength = <12>; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + bias-disable; + drive-strength = <2>; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Luma-WRTQ-329ACN"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "Luma-WRTQ-329ACN"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 0f03e1f429..5c76bc39b7 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -540,6 +540,18 @@ define Device/linksys_ea8300 endef TARGET_DEVICES += linksys_ea8300 +define Device/luma_wrtq-329acn + $(call Device/FitImage) + DEVICE_VENDOR := Luma Home + DEVICE_MODEL := WRTQ-329ACN + SOC := qcom-ipq4018 + DEVICE_PACKAGES := ipq-wifi-luma_wrtq-329acn kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio uboot-envtools + IMAGE_SIZE := 76632k + BLOCKSIZE := 128k + PAGESIZE := 2048 +endef +TARGET_DEVICES += luma_wrtq-329acn + define Device/meraki_mr33 $(call Device/FitImage) DEVICE_VENDOR := Cisco Meraki diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 2b5220d3ed..0fc50217c4 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,52 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,53 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -33,6 +33,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-oap100.dtb \ + qcom-ipq4018-rt-ac58u.dtb \ + qcom-ipq4018-wre6606.dtb \ ++ qcom-ipq4018-wrtq-329acn.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ qcom-ipq4019-ap.dk04.1-c1.dtb \ qcom-ipq4019-ap.dk04.1-c3.dtb \ |